ACE deploying issue,

Hi,
I have question in regards to Deploying configurations to ACE with ANM. I presume it should deploy it in few seconds but for me it takes 8 to 10 minutes. Can anyone suggest why is this taking so much time????
Thanks in advance.

Do you have a large config? How many contexts?
Is there an issue with the connection between the ANM server and the ACE (low bandwidth,...)
Did you install the ANM on an approved server (meets the min requirements?)
ACE is well discovered by ANM?
Keep us posted.

Similar Messages

  • Typical/Common large-scale ACE deployment or designs?

    I am deploying several ACE devices and GSS devices to facilitate redundancy and site load balancing at a couple of data centers.  Now that I have a bunch of experience with the ACE and GSS, are there typical or common ACE deployment methods?  Are there reference designs?  I have been looking, and haven't really found any.
    Even if they are not Cisco 'official' methods, I'm wondering how most people, particularily those who deploy a lot of these or deploy them with large-scale systems, typically do it.
    I'm using routed mode (not one-arm mode) and I'm wondering if most people use real server (in my case, web servers) with dual-NICs to support connectivity to back-end systems?  Or do people commonly just route it all through the ACE?
    Also, how many VIPs and real servers have been deployed in a single ACE 4710 device?  I'm trying to deploy about 700 VIPs with about 1800 Real Servers providing content to those VIPs.
    How do people configure VIPs, farms, and sticky?  I'm looking for how someone who wants to put a large ammount of VIPs and real servers into the ACE would succeed at doing it.  I have attempted to add a large number in the 'global' policy-map, but that uses too many PANs.
    I have tried a few methods myself, and have run into the limit on Policy Action Nodes (PANs) in the ACE device.  Has anyone else hit this issue?  Any tips or tricks on how to use PANs more conservitively?
    Any insight you can share would be appreciated.
    - Erik

    As far as i can see from your requirements i suggest you create 1 ear file for your portal and 1 ear file per module.
    The ear file from your portal is the main application and the ear files of your modules are shared libraries that contain the taskflows. These taskflows can be consumed in the portal application.
    This way, you can easily deploy 1 module without needing to deploy the main application or the other application.
    It also let you devide your team of developer so everybody can work on a sepperate module without interfering.
    On a sidenote: when you have deployed your main application, and later you create a new module, than you have to register that module to your application so then you will need to redeploy your portal but if you update an existing module, you won't need to redeploy your portal.
    As for the security, all your modules will inherit the security model of your portal application.

  • Outbound BPEL Process deployment Issue in SOA (binding.jca-12600)

    Hi,
    I have Designed an Outbound BPEL Process for Siebel CRM Service Integration using Jdeveloper (11.1.1.3.0). After that I am facing the deployment issue of this application in SOA suite (11.1.1.6.0). Following is the deployment.log status in jdeveloper:-
    [10:57:54 AM] ---- Deployment started. ----
    [10:57:54 AM] Target platform is (Weblogic 10.3).
    [10:57:54 AM] Running dependency analysis...
    [10:57:54 AM] Building...
    [10:57:58 AM] Deploying profile...
    [10:57:58 AM] Wrote Archive Module to C:\JDeveloper\mywork\Siebel_Outbound_BPEL\QueryWithView_Invoke\deploy\sca_QueryWithView_Invoke_rev1.0.jar
    [10:57:58 AM] Deploying sca_QueryWithView_Invoke_rev1.0.jar to partition "default" on server AdminServer [10.10.22.81:7001]
    [10:57:58 AM] Processing sar=/C:/JDeveloper/mywork/Siebel_Outbound_BPEL/QueryWithView_Invoke/deploy/sca_QueryWithView_Invoke_rev1.0.jar
    [10:57:58 AM] Adding sar file - C:\JDeveloper\mywork\Siebel_Outbound_BPEL\QueryWithView_Invoke\deploy\sca_QueryWithView_Invoke_rev1.0.jar
    [10:57:58 AM] Preparing to send HTTP request for deployment
    [10:57:59 AM] Creating HTTP connection to host:10.10.22.81, port:7001
    [10:57:59 AM] Sending internal deployment descriptor
    [10:57:59 AM] Sending archive - sca_QueryWithView_Invoke_rev1.0.jar
    [10:58:00 AM] Received HTTP response from the server, response code=500
    [10:58:00 AM] Error deploying archive sca_QueryWithView_Invoke_rev1.0.jar to partition "default" on server AdminServer [10.10.22.81:7001]
    [10:58:00 AM] HTTP error code returned [500]
    [10:58:00 AM] Error message from server:
    #;There was an error deploying the composite on AdminServer: Deployment Failed: [JCABinding] [QueryWithView_Invoke.QueryWithView/1.0]Unable to complete load due to: Generic error.
    #;Generic error.
    #;Cause: Unable to find suitable outbound binding.
    #;Please create a Service Request with Oracle Support.
    #;: Generic error.
    #;Generic error.
    #;Cause: Unable to find suitable outbound binding.
    #;Please create a Service Request with Oracle Support.
    [10:58:00 AM] Check server log for more details.
    [10:58:00 AM] Error deploying archive sca_QueryWithView_Invoke_rev1.0.jar to partition "default" on server AdminServer [10.10.22.81:7001]
    [10:58:00 AM] #### Deployment incomplete. ####
    [10:58:00 AM] Error deploying archive file:/C:/JDeveloper/mywork/Siebel_Outbound_BPEL/QueryWithView_Invoke/deploy/sca_QueryWithView_Invoke_rev1.0.jar
    (oracle.tip.tools.ide.fabric.deploy.common.SOARemoteDeployer)
    And the following is the SOA Server Side log file status:-
    ####<Jun 3, 2013 10:36:05 AM AST> <Info> <Health> <HOSADDAT02> <AdminServer> <weblogic.GCMonitor> <<anonymous>> <> <4be72ac3bdb5ebae:-a61256d:13f08d94c98:-8000-00000000000000f4> <1370244965280> <BEA-310002> <36% of the total memory in the server is free>
    ####<Jun 3, 2013 10:36:12 AM AST> <Error> <ServletContext-/soa-infra> <HOSADDAT02> <AdminServer> <[ACTIVE] ExecuteThread: '2' for queue: 'weblogic.kernel.Default (self-tuning)'> <weblogic> <> <4be72ac3bdb5ebae:-a61256d:13f08d94c98:-8000-000000000000182b> <1370244972343> <BEA-000000> <Error during deployment
    oracle.fabric.common.FabricException: Deployment Failed: [JCABinding] [QueryWithView_Invoke.QueryWithView/1.0]Unable to complete load due to: Generic error.
    Generic error.
    Cause: Unable to find suitable outbound binding.
    Please create a Service Request with Oracle Support.
    : Generic error.
    Generic error.
    Cause: Unable to find suitable outbound binding.
    Please create a Service Request with Oracle Support.
         at oracle.integration.platform.blocks.deploy.StandaloneCompositeDeploymentCoordinatorImpl.coordinateCompositeDeployment(StandaloneCompositeDeploymentCoordinatorImpl.java:64)
         at oracle.integration.platform.blocks.deploy.servlet.BaseDeployProcessor.deployNewComposite(BaseDeployProcessor.java:415)
         at oracle.integration.platform.blocks.deploy.servlet.BaseDeployProcessor.deploySARs(BaseDeployProcessor.java:250)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.doDeployWork(DeployProcessor.java:167)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.doDeployWork(DeployProcessor.java:112)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.doDeploy(DeployProcessor.java:99)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.process(DeployProcessor.java:81)
         at oracle.integration.platform.blocks.deploy.servlet.CompositeDeployerServlet.doPostInsideLoggingSession(CompositeDeployerServlet.java:219)
         at oracle.integration.platform.blocks.deploy.servlet.CompositeDeployerServlet.doPost(CompositeDeployerServlet.java:130)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:727)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)
         at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
         at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
         at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:301)
         at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:119)
         at java.security.AccessController.doPrivileged(Native Method)
         at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:315)
         at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:442)
         at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:103)
         at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:171)
         at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:119)
         at java.security.AccessController.doPrivileged(Native Method)
         at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:315)
         at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:442)
         at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:103)
         at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:171)
         at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:139)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.wrapRun(WebAppServletContext.java:3730)
         at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3696)
         at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
         at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)
         at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2273)
         at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2179)
         at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1490)
         at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)
         at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)
    Caused By: oracle.fabric.common.FabricDeploymentException: [JCABinding] [QueryWithView_Invoke.QueryWithView/1.0]Unable to complete load due to: Generic error.
    Generic error.
    Cause: Unable to find suitable outbound binding.
    Please create a Service Request with Oracle Support.
    : Generic error.
    Generic error.
    Cause: Unable to find suitable outbound binding.
    Please create a Service Request with Oracle Support.
    {rootCauses=[]}
         at oracle.integration.platform.blocks.adapter.AdapterReference.load(AdapterReference.java:458)
         at oracle.integration.platform.blocks.adapter.AdapterReference.load(AdapterReference.java:82)
         at oracle.integration.platform.blocks.deploy.CompositeDeploymentConnection.deployReferences(CompositeDeploymentConnection.java:201)
         at oracle.integration.platform.blocks.deploy.CompositeDeploymentConnection.deploy(CompositeDeploymentConnection.java:93)
         at oracle.integration.platform.blocks.deploy.CompositeDeploymentManagerImpl.initDeployment(CompositeDeploymentManagerImpl.java:150)
         at oracle.integration.platform.blocks.deploy.CompositeDeploymentManagerImpl.load(CompositeDeploymentManagerImpl.java:63)
         at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
         at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
         at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
         at java.lang.reflect.Method.invoke(Method.java:597)
         at org.springframework.aop.support.AopUtils.invokeJoinpointUsingReflection(AopUtils.java:307)
         at org.springframework.aop.framework.ReflectiveMethodInvocation.invokeJoinpoint(ReflectiveMethodInvocation.java:182)
         at org.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:149)
         at oracle.integration.platform.blocks.deploy.DeploymentEventPublisher.invoke(DeploymentEventPublisher.java:77)
         at org.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:171)
         at org.springframework.aop.framework.JdkDynamicAopProxy.invoke(JdkDynamicAopProxy.java:204)
         at $Proxy314.load(Unknown Source)
         at oracle.integration.platform.blocks.deploy.StandaloneCompositeDeploymentCoordinatorImpl.coordinateCompositeDeployment(StandaloneCompositeDeploymentCoordinatorImpl.java:59)
         at oracle.integration.platform.blocks.deploy.servlet.BaseDeployProcessor.deployNewComposite(BaseDeployProcessor.java:415)
         at oracle.integration.platform.blocks.deploy.servlet.BaseDeployProcessor.deploySARs(BaseDeployProcessor.java:250)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.doDeployWork(DeployProcessor.java:167)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.doDeployWork(DeployProcessor.java:112)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.doDeploy(DeployProcessor.java:99)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.process(DeployProcessor.java:81)
         at oracle.integration.platform.blocks.deploy.servlet.CompositeDeployerServlet.doPostInsideLoggingSession(CompositeDeployerServlet.java:219)
         at oracle.integration.platform.blocks.deploy.servlet.CompositeDeployerServlet.doPost(CompositeDeployerServlet.java:130)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:727)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)
         at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
         at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
         at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:301)
         at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:119)
         at java.security.AccessController.doPrivileged(Native Method)
         at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:315)
         at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:442)
         at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:103)
         at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:171)
         at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:119)
         at java.security.AccessController.doPrivileged(Native Method)
         at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:315)
         at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:442)
         at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:103)
         at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:171)
         at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:139)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.wrapRun(WebAppServletContext.java:3730)
         at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3696)
         at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
         at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)
         at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2273)
         at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2179)
         at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1490)
         at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)
         at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)
    Caused By: BINDING.JCA-12600
    Generic error.
    Generic error.
    Cause: Unable to find suitable outbound binding.
    Please create a Service Request with Oracle Support.
         at oracle.integration.platform.blocks.adapter.fw.metadata.AdapterBindingConfig.addAdapterReference(AdapterBindingConfig.java:206)
         at oracle.integration.platform.blocks.adapter.AdapterReference.setupAdapterReference(AdapterReference.java:506)
         at oracle.integration.platform.blocks.adapter.AdapterReference.load(AdapterReference.java:425)
         at oracle.integration.platform.blocks.adapter.AdapterReference.load(AdapterReference.java:82)
         at oracle.integration.platform.blocks.deploy.CompositeDeploymentConnection.deployReferences(CompositeDeploymentConnection.java:201)
         at oracle.integration.platform.blocks.deploy.CompositeDeploymentConnection.deploy(CompositeDeploymentConnection.java:93)
         at oracle.integration.platform.blocks.deploy.CompositeDeploymentManagerImpl.initDeployment(CompositeDeploymentManagerImpl.java:150)
         at oracle.integration.platform.blocks.deploy.CompositeDeploymentManagerImpl.load(CompositeDeploymentManagerImpl.java:63)
         at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
         at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
         at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
         at java.lang.reflect.Method.invoke(Method.java:597)
         at org.springframework.aop.support.AopUtils.invokeJoinpointUsingReflection(AopUtils.java:307)
         at org.springframework.aop.framework.ReflectiveMethodInvocation.invokeJoinpoint(ReflectiveMethodInvocation.java:182)
         at org.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:149)
         at oracle.integration.platform.blocks.deploy.DeploymentEventPublisher.invoke(DeploymentEventPublisher.java:77)
         at org.springframework.aop.framework.ReflectiveMethodInvocation.proceed(ReflectiveMethodInvocation.java:171)
         at org.springframework.aop.framework.JdkDynamicAopProxy.invoke(JdkDynamicAopProxy.java:204)
         at $Proxy314.load(Unknown Source)
         at oracle.integration.platform.blocks.deploy.StandaloneCompositeDeploymentCoordinatorImpl.coordinateCompositeDeployment(StandaloneCompositeDeploymentCoordinatorImpl.java:59)
         at oracle.integration.platform.blocks.deploy.servlet.BaseDeployProcessor.deployNewComposite(BaseDeployProcessor.java:415)
         at oracle.integration.platform.blocks.deploy.servlet.BaseDeployProcessor.deploySARs(BaseDeployProcessor.java:250)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.doDeployWork(DeployProcessor.java:167)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.doDeployWork(DeployProcessor.java:112)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.doDeploy(DeployProcessor.java:99)
         at oracle.integration.platform.blocks.deploy.servlet.DeployProcessor.process(DeployProcessor.java:81)
         at oracle.integration.platform.blocks.deploy.servlet.CompositeDeployerServlet.doPostInsideLoggingSession(CompositeDeployerServlet.java:219)
         at oracle.integration.platform.blocks.deploy.servlet.CompositeDeployerServlet.doPost(CompositeDeployerServlet.java:130)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:727)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)
         at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
         at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
         at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:301)
         at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:119)
         at java.security.AccessController.doPrivileged(Native Method)
         at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:315)
         at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:442)
         at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:103)
         at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:171)
         at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.security.jps.ee.http.JpsAbsFilter$1.run(JpsAbsFilter.java:119)
         at java.security.AccessController.doPrivileged(Native Method)
         at oracle.security.jps.util.JpsSubject.doAsPrivileged(JpsSubject.java:315)
         at oracle.security.jps.ee.util.JpsPlatformUtil.runJaasMode(JpsPlatformUtil.java:442)
         at oracle.security.jps.ee.http.JpsAbsFilter.runJaasMode(JpsAbsFilter.java:103)
         at oracle.security.jps.ee.http.JpsAbsFilter.doFilter(JpsAbsFilter.java:171)
         at oracle.security.jps.ee.http.JpsFilter.doFilter(JpsFilter.java:71)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.dms.servlet.DMSServletFilter.doFilter(DMSServletFilter.java:139)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.wrapRun(WebAppServletContext.java:3730)
         at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3696)
         at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
         at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)
         at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2273)
         at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2179)
         at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1490)
         at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)
         at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)
    Kindly help me in this regard

    Solution:
    Workaround the issue immediately by removing the "ns1:" qualification on the operation for the binding.jca entry in the composite.xml and redeploying.
    For example:
    From:
    <binding.jca config="BAPI_COMPANYCODE_GETDETAIL_invoke_3P.jca"
    operation="ns1:BAPI_COMPANYCODE_GETDETAIL"/>
    To:
    <binding.jca config="BAPI_COMPANYCODE_GETDETAIL_invoke_3P.jca"
    operation="BAPI_COMPANYCODE_GETDETAIL"/>
    Regards,
    Shaheer Badar

  • Adobe Acrobat 9 Pro deployment issue

    Hello. I am having a deployment issue with Adobe Acrobat 9 using Altiris. I create the rip which is bassically an image of the install. My facility has pruchased 50 seats for this software so I know we are covered for the users that we have to use this software. The issue that I am having after I make the rip, and deploy it to a machine it asks for the CD key again in order to use. Am I having an issue with my installation or is Adobe put some kind of security into their software so that when you try to make a rip of the installation is asks for teh CD Key again after the install? Is this an issue that can be resolved?

    SOLUTION:
    The issue was somehow related to DPI (START > Settings > Control Pannel > Display > Settings Tab > Advanced button). Eventhough the DPI was set to normal, I switched it to LARGE, restarted the machine, logged in after the reboot, changed it back to normal size, restarted again, logged in once more, checked the Printer Preferences and PRESTO --- a properly displayed window.

  • Deploy issue from JDeveloper 10.1.3.5 to OAS 10.1.2

    I have written an application using ADF on JDeveloper 10.1.3.5 and need to deploy it to our OAS 10.1.2. I have run the adfinstaller on the linux server to upgrade the ADF libraries to the correct versions, updated the web.xml files to have the correct versions, changed to J2SE 1.4.2_19 for the application and have still got deployment issues.
    Error
    An error occurred while redeploying application "FormsSiebelIntegration". See base exception for details.
    Resolution:
    See base exception for details.
    Base Exception:
    java.lang.UnsupportedClassVersionError
    com/sun/faces/application/ApplicationAssociate (Unsupported major.minor version 49.0). com/sun/faces/application/ApplicationAssociate (Unsupported major.minor version 49.0)
    Removing the jsf-impl.jar file allows the application to deploy, but when running on the app server I get the following errors:
    OracleJSP: oracle.jsp.parse.JspParseException:
    /codename.jspx: Line # 6, <jsp:root xmlns:jsp="http://java.sun.com/JSP/Page" version="2.0" xmlns:h="http://java.sun.com/jsf/html" xmlns:f="http://java.sun.com/jsf/core" xmlns:af="http://xmlns.oracle.com/adf/faces" xmlns:afh="http://xmlns.oracle.com/adf/faces/html">
    Help! I'm starting to have total mind block as to what to do next.
    Error: Unable to load taghandler class: http://java.sun.com/jsf/html

    I had already applied all of this before trying to deploy.
    The error seems to be a versioning error in the jsf-impl.jar file as the ApplicationAssociate class is found there. I have changed the JDK and J2EE to 1.4.2 and 1.3 respectively, rebuilt everything, updated all the settings to the right versions for 10.1.2 but it still keeps failing on the deploy.

  • A very urgent deployment issue about DBAdapter

    Hello All,
    I have a very urgent deployment issue about DBAdapter.
    That DBAdapter is connect to DB2 AS400 Database. I have a developing database (jdbc:as400://server01/TEST) and a production database (jdbc:as400://server01/PROD).
    During developing, I used DBAdapter wizard to create it, and import some tables, and set the Adapter to use jabc/DB2DS as connection information for easily deployment later.
    Then I deploy to Production. I configured Data-source.xml and oc4j-ra.xml rightly; I set DB connection point to production database. But the DBAdapter still write into developing Database.
    I checked the DBAdapter, the imported tables are something like this, TEST.table1, TEST.table2. And there are a lot "TEST" located in DB2Writer_toplink_mapping.xml, DB2Writer.xml, TEST.schema, DB2Writer.table1.ClassDescriptor.xml.
    This TEST is refrer to the TEST in connect String jdbc:as400://server01/TEST.
    I think this might be the reason cause the problem. As to production database, "TEST" should replaced by "PROD". If I changed it manually, I have to change every time when switch between TEST and PROD. And I also don't know if it is safe to do it? (I tried, and bring some toplink mapping problem)
    By the way, for Oracle Database, because we use 2 instances for testing and production with same schema name, and do not have this issue.
    Anyone could help and many thanks.
    Kerr
    Message was edited by:
    Kerr

    Hi Kerr,
    The idea is to set up all connections in the BPEL or ESB services with logical names, e.g. typically of the form eis/DB/MyFinancialSystem or eis/DB/MyLogisticsSystem. This way, you do not have to modify code when deploying it onto different environments that serve different purposes.
    When moving your services through their lifecyle, on every environment you deploy these to you will have the same logical connections configured on each instance, e.g. for DEV, QA, SIT, UAT and PROD. Only, in case of QA the actual physical connection is configured to point to the QA instance of the systems that your services interact with whereas in case of UAT it points to the UAT instance of the same system.
    Maybe your problem is caused by connecting as user "SomeUser" when running the DB Adapter wizard during development and actually selecting objects from a different schema than you used to connect with, e.g. "Test" in your case.
    Hth,
    Sjoerd

  • ACE Configuration Issue.

    We would like to configure on ace like below:
    the virtual ip address and port like this
    : 10.10.10.10:8000,this ip address will be use to outside user request servie
    and we have to configure server farm like below
    real server 10.10.10.1:8001, 10.10.10.1:8002, 10.10.10.1:8003 ...
    the ip address is same on 10.10.10.10:8000's serverfarm, but real server service is different, and this port should be loadbalanced and healchecked.
    Is it possible solution? F5 big ip , Nortal is possible, but I don't know on ACE above issue.
    If you ok. could you give me a sample configuration?

    page 2....
    Also i forget to tell you to
    8.create resourse-class
    9. create context othr then admin context if you need multiple contexts:
    (inside context add resource class)
    10 class map type management (for remote access)
    as follows:
    Kindly find some config sample as follows:
    ACE/Admin# sh run
    Generating configuration....
    resource-class ABCD_Resource
    limit-resource all minimum 5.00 maximum unlimited
    limit-resource sticky minimum 5.00 maximum unlimited
    boot system image:c4710ace-mz.A3_2_1.bin
    hostname ACE
    context Admin
    member ABCD_Resource
    access-list everyone line 10 extended permit icmp any any
    access-list everyone line 20 extended permit ip any any
    access-list for-cap line 8 extended permit ip any any
    probe http HTTP-Probe
    port 8000
    interval 2
    faildetect 2
    passdetect interval 15
    request method head
    probe icmp ICMP-Probe
    interval 2
    faildetect 2
    passdetect interval 60
    probe tcp TCP-8000
    port 8000
    interval 2
    faildetect 2
    passdetect interval 15
    passdetect count 2
    open 1
    rserver host A
    ip address 10.10.10.1
    inservice
    rserver host B
    ip address 10.10.10.2
    inservice
    rserver host C
    ip address 10.10.10.3
    inservice
    rserver host D
    ip address 10.10.10.4
    inservice
    serverfarm host SF-8000-1
    probe ICMP-Probe
    probe TCP-8000
    rserver A 8000
    inservice
    rserver B 8000
    inservice
    serverfarm host SF-8000-2
    probe HTTP-Probe
    probe ICMP-Probe
    probe TCP-8000
    rserver C 8000
    inservice
    rserver D 8000
    inservice
    class-map match-all L4-CLASS-REDIRECT-1
    2 match virtual-address 10.10.60.10 tcp eq www
    class-map match-all VIP-PORT-8000-1
    2 match virtual-address 10.10.60.10 tcp eq https
    class-map match-all VIP-PORT-8000-2
    2 match virtual-address 10.10.60.12 tcp eq https
    class-map type management match-any remote-mgmt
    10 match protocol ssh any
    20 match protocol telnet any
    30 match protocol icmp any
    40 match protocol http any
    50 match protocol https any
    class-map match-any server-initiated
    3 match source-address 10.10.10.4 255.255.255.255
    4 match source-address 10.10.10.3 255.255.255.255
    policy-map type management first-match remote-access
    class remote-mgmt
    permit
    policy-map type loadbalance first-match VIP-POLICY-8000-1
    class class-default
    policy-map multi-match Service-Policy-8000-1
    class VIP-PORT-8000-1
    loadbalance vip inservice
    loadbalance policy VIP-POLICY-8000-1
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 60
    class L4-CLASS-REDIRECT-1
    loadbalance vip inservice
    loadbalance policy VIP-POLICY-8000-1
    policy-map multi-match Service-Policy-8000-2
    class VIP-PORT-8000-2
    loadbalance vip inservice
    loadbalance policy VIP-POLICY-8000-2
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 60
    ssl-proxy server SSL-Offload-Proxy-2
    policy-map multi-match server-side
    class server-initiated
    nat dynamic 1 vlan 60
    interface vlan 10
    description APPPROD-Client-Vlan
    bridge-group 10
    mtu 1500
    access-group input everyone
    access-group output everyone
    service-policy input remote-access
    no shutdown
    interface vlan 30
    description management-vlan-interface
    ip address 10.10.30.22 255.255.255.0
    access-group input everyone
    access-group output everyone
    service-policy input remote-access
    no shutdown
    continued page 3......

  • Re: Deployment Issues

    Hi Dale;
    We have the similar situation. We wrote an application to be able to send
    alert message before we shut down the Forte application. When we upgrade our
    applications, we will send alert message to all users before we shut down the
    Forte application through ECONSOLE which forces all users to log out, and then
    overwrite the files.
    Our client files are sitting at one of our network servers instead of
    individual user's PC, so the user accesses the files through network. So we
    are facing the same issue that we have to shut all users down before we
    upgrade our applications. If you install those files on your individual user's
    PC, you may try to use "compatible level" to update your application.
    Hope this helps.
    Lu Wang
    Eli Lilly and Company
    [email protected]

    My problem lies more in the way that we update the Forte software. We are
    controlled enough with a new distribution from the application side that
    there are not problems there.
    My question is: how is everyone updating their client PC's from say Forte
    R2 to R3. This was not a problem before because we didn't have very many
    clients. Now we have quite a few and we can't just copy the proper files
    because of the registry updates that are required.
    Does anyone have any suggestions? Can I run the Forte client software off
    the Novell server?
    Thanks,
    Tony
    -----Original Message-----
    From: Lu Wang X1 <[email protected]>
    To: Dale V. Georg <[email protected]>
    Cc: Forte Users <[email protected]>; Gardner, Steve
    <[email protected]>
    Date: Wednesday, November 19, 1997 11:17 AM
    Subject: Re: Deployment Issues
    You are right. Through econsole, we can only shut down the serverpartitions,
    even though we can uninstall the application, as long as the clientpartition
    is running, we can't overwrite the files. We were probably lucky that nouser
    was running the application when we upgraded it.
    Since our applications can capture the system alert message, probably wecan
    make changes to our application to be able to shut itself down when it
    receives certain type of alert message. Just a thought. Don't know ifthere
    is any better way to handle it.
    Lu
    "Dale V. Georg" <[email protected]> on 11/19/97 03:02:27 AM
    Please respond to "Dale V. Georg" <[email protected]>
    To: Lu Wang X1/AM/LLY
    cc: Forte Users <[email protected]>, "Gardner, Steve"
    <[email protected]>
    Subject: Re: Deployment Issues
    On Tue, 18 Nov 1997 11:04:53 -0500, Lu Wang X1 wrote:
    Hi Dale;
    We have the similar situation. We wrote an application to be able to send
    alert message before we shut down the Forte application. When we upgradeour
    applications, we will send alert message to all users before we shut down
    the
    Forte application through ECONSOLE which forces all users to log out, andthen
    overwrite the files.If I remember correctly, econsole will only forcibly close down the
    server partitions, not the client partitions.
    Our client files are sitting at one of our network servers instead of
    individual user's PC, so the user accesses the files through network. So
    we
    are facing the same issue that we have to shut all users down before we
    upgrade our applications. If you install those files on your individualuser's
    PC, you may try to use "compatible level" to update your application.We did think about using the compatibility level at one point, but that
    introduces extra maintenence whenever a new version of the application
    is rolled out. On the other hand, if that's the cost of a smooth and
    reliable upgrade, then it may be worth paying.
    Dale
    ================================================
    Dale V. Georg
    Systems Analyst
    Indus Consultancy Services
    [email protected]
    ================================================

  • Ear deployment issue.

    Hi,
    i am using jdev Studio Edition Version 11.1.1.4.0
    I have created EAR of my application and trying to depoly it on Weblogic server.
    I have following entry in weblogic-application.xml
    <library-ref>
    <library-name>adf.oracle.domain</library-name>
    </library-ref>
    [03:12:39 PM] ---- Deployment started. ----
    [03:12:39 PM] Target platform is (Weblogic 10.3).
    [03:13:07 PM] Retrieving existing application information
    [03:13:07 PM] Running dependency analysis...
    [03:13:07 PM] Building...
    [03:13:28 PM] Deploying 3 profiles...
    [03:13:29 PM] Moving WEB-INF/adfc-config.xml to META-INF/adfc-config.xml
    [03:13:30 PM] Wrote Archive Module to /home/kpophale/CDMR/13June/frontend/ConsoleApps/AppsInventoryManagerUi/deploy/AppsInventoryManagerUi.jar
    [03:13:38 PM] Wrote Web Application Module to /home/kpophale/CDMR/13June/frontend/ConsoleApps/AppsInventoryManagerUi/deploy/AppsInventory.war
    *[03:13:38 PM] Removing the following prohibited entry from the EAR: lib/trinidad-api.jar*
    *[03:13:38 PM] Removing the following prohibited entry from the EAR: lib/trinidad-impl.jar*
    [03:13:38 PM] removed bundleresolver.jar from lib because it cannot be part of an EJB deployment
    [03:13:54 PM] Wrote Enterprise Application Module to /home/kpophale/CDMR/13June/frontend/deploy/AppsInventoryManager.ear
    [03:13:55 PM] Entering Oracle Deployment Plan Editor
    [03:15:53 PM] Deploying Application...
    [03:16:41 PM] [Deployer:149034]An exception occurred for task [Deployer:149026]deploy application AppsInventoryManager on AdminServer.: [Deployer:149145]Unable to contact 'bam_server1'. Deployment is deferred until 'bam_server1' becomes available.; nested exception is:
         java.rmi.UnknownHostException: Could not discover administration URL for server 'bam_server1'.
    [03:16:41 PM] [Deployer:149034]An exception occurred for task [Deployer:149026]deploy application AppsInventoryManager on AdminServer.: [Deployer:149145]Unable to contact 'osb_server1'. Deployment is deferred until 'osb_server1' becomes available.; nested exception is:
         java.rmi.UnknownHostException: Could not discover administration URL for server 'osb_server1'.
    [03:16:41 PM] [Deployer:149034]An exception occurred for task [Deployer:149026]deploy application AppsInventoryManager on AdminServer.: [Deployer:149145]Unable to contact 'soa_server1'. Deployment is deferred until 'soa_server1' becomes available.; nested exception is:
         java.rmi.UnknownHostException: Could not discover administration URL for server 'soa_server1'.
    [03:16:41 PM] [Deployer:149034]An exception occurred for task [Deployer:149026]deploy application AppsInventoryManager on AdminServer.: [Deployer:149145]Unable to contact 'adf_server1'. Deployment is deferred until 'adf_server1' becomes available.; nested exception is:
         java.rmi.UnknownHostException: Could not discover administration URL for server 'adf_server1'.
    [03:16:41 PM] [Deployer:149193]Operation 'deploy' on application 'AppsInventoryManager' has failed on 'AdminServer'
    [03:16:41 PM] [Deployer:149034]An exception occurred for task [Deployer:149026]deploy application AppsInventoryManager on AdminServer.: Failed to load webapp: 'trellis-AppsInventoryManagerUi-context-root'.
    [03:16:41 PM] Weblogic Server Exception: weblogic.application.ModuleException: Failed to load webapp: 'trellis-AppsInventoryManagerUi-context-root'
    *[03:16:41 PM] Caused by: java.lang.NoClassDefFoundError: org/apache/myfaces/trinidad/webapp/UIXComponentELTag*
    [03:16:41 PM] See server logs or server console for more details.
    [03:16:41 PM] weblogic.application.ModuleException: Failed to load webapp: 'trellis-AppsInventoryManagerUi-context-root'
    [03:16:41 PM] #### Deployment incomplete. ####
    [03:16:41 PM] Remote deployment failed (oracle.jdevimpl.deploy.common.Jsr88RemoteDeployer)
    I am getting above exception while i am trying to depoly the my ear. please see bold lines.
    Please give me some guide line .
    Regards,
    Kiran.

    Hi John,
    Yes I have. I even tried on two seperate WebLogic installations. I noticed, even when I create just an ear file (not deploy to server), it gives me the same warnings about removing trinidad. Is there something i'm missing in JDeveloper?
    For my installations:
    On one Middleware home: I installed: WLS 10.3.5, ADF 11.1.1.5, then ADF 11.1.2 Patch 12611176. configured domain with all ADF/JRF libraries, followed by upgradeADF WLST command. I got same deployment issue.
    On another middleware home: I even just installed JDeveloper 11.1.2, configured a new domain with all librearies. I got same deployment issue.
    FYI: I also added the two Trinidad JSP Tag Libraries to my View Controller Project. I got same error.
    Thank you,
    Gavin
    Edited by: GavinWoods on Feb 14, 2012 6:25 AM

  • EPMA Deployment Issues (Rollback Database)

    I have seen some posts where users were able to rollback their EPMA databases. This could be helpful when running into deployment issues. Can anyone outline the steps that are needed to rollback an EPMA database?
    Thank you

    spring_patel wrote:
    i really appreciate you trying to solve my problem..
    but i think...my estion is fairly simple and straight forward...and i've provided every detail of my problem(if uv'e read my opening post of this thread)....
    and as far as that link goes...i've already checked it b4 u guys mentioned it... as it is provided right there in the tutorial i've provided link of...
    and i've tried my options b4 making use of this forum...and i didnt find a solution that's why i'm taking ur help..
    nevertheless...i repeat my question...
    there's a tutorial at this link...[http://www.netbeans.org/kb/docs/java/gui-db.html]...in it is described how to create a java desktop database applicaiton...
    at the end of the tuorial there is a section called: "Building and Deploying the Application"
    in that section they have instructed to exit netbeans IDE and try and run the application outside it...which is not happening
    the reason they say is that i've to start Java DB from outside of the IDE...that is wat my problem is ..
    i dont know how to start Java DB from outside the Netbeans ide...You are not telling us anything.
    If I tell you "my automobile doesn't work" how do you know what is wrong. Instead I need to tell you one of the following.
    1. The engine didn't start.
    2. The wheel fell off.
    3. The engine caught fire.
    4. When I went to the driveway the car wasn't even there.
    When you "run" something then something happens. When I run notepad from a console window if notepad is not in the path then I will get an error about command not found. if it is in the path then the command executes and notepad pops up. Even if I don't see notepad pop up I know that the command seemed to execute from the command window.
    The above are examples of describing what you did and what did happen. In detail.
    "It doesn't work" provides neither detail about how you ran it nor what did happen when you did attempt to run it.

  • Deployment issue: compatiblity issue with ODP, instant vs full client on PC

    After a lot of deployment issues with full client, we thought we had the solution with Instant Client.
    It worked great for a while, but now some of our users have full Oracle 11 client installed after installing our Instant Client because of other software that requires full client.
    As soon as they install full client, our Instant Client breaks:
    Exception has been thrown by the target of an invocation. (mscorlib)
    The type initializer for 'Oracle.DataAccess.Client.OracleClientFactory' threw an exception.
    The provider is not compatible with the version of Oracle client (Oracle Data Provider for .NET)
    Our instant client is compiled with 2.111.6.20, the client is installing a different version (though I tried installing exactly same version does not seem to work either)
    I've been experimenting to redirect the version to another assembly but no success.
    How can I make Instant Client and Full client co-exist? The whole idea of using Instant was to be independent of other software who needs ODP.NET...
    What do you do when 2 apps need different versions of ORacle ODP.NET (e.g. 2.111.6.0 vs. 2.112.1.0)?
    Note that I don't have source code access to "our" app, so if it is at all possible through configuration, that is a prefered solution.
    I also don't control our customers deployment strategy, they roll out apps over 1000's of PC's

    According to documentation at [http://docs.oracle.com/cd/E20434_01/doc/win.112/e23174/featConfig.htm]
    >
    Configuration File Support
    For customers who have numerous applications on a computer that depends on a single version of ODP.NET, the Windows Registry settings for a given version of ODP.NET may not necessarily be applicable for all applications that use that version of ODP.NET. To provide more granular control, ODP.NET Configuration File Support allows developers to specify ODP.NET configuration settings in an application config, web.config, or a machine.config file.
    If a computer does not require granular control beyond configuration settings at the ODP.NET version level, there is no need to specify ODP.NET configuration settings through configuration files.
    The following is an example of a web.config file for .NET Framework 2.0 and higher:
    <?xml version="1.0" encoding="utf-8" ?>
    <configuration>
    <oracle.dataaccess.client>
    <settings>
    <add name="DllPath" value="C:\oracle\bin"/>
    <add name="FetchSize" value="131072"/>
    <add name="PromotableTransaction" value="promotable"/>
    <add name="StatementCacheSize" value="10"/>
    <add name="TraceFileName" value="C:\odpnet2.trc"/>
    <add name="TraceLevel" value="63"/>
    <add name="TraceOption" value="1"/>
    </settings>
    </oracle.dataaccess.client>
    </configuration>

  • ACE deployment considerations

    folks
    i'm looking for a good practice guide for ace deployment if anyone can help
    i intend to use my ACE appliance to load balance traffic between 4 different proxy servers, i.e. users request a url, i.e. www.cnn.com from the ACE and it then connects to one of 4 proxies which will then retrieve the web page, pass it back to the ACE which will deliver the content to the user
    my ACE appliance is no my trusted/corporate lan
    my proxies are on an untrusted lan/dmz behind a firewall
    i want to install a 4710 with its client interface on my corporate lan (closest to the users) and the server interface on my proxy lan but i need to know if the ACE appliance is secure enough to be deployed in this topology
    is it EAL certified or does it run in a firewall/stateful inspection mode?
    thanks to anyone taking the time to read this or to reply

    Hi,
    As far as I know, the ACE is not stateful like your typical firewall device, and I have no knowledge of wether it's EAL certified or not.
    However, since ACE comes with a wide range of inspection features and is generally considered very security-aware, you could argue that it would make a good firewall substitute. Personally, I've deployed the ACE as an addition to my firewall setup and attached the proxies to ACE on dedicated interfaces, having a clientside interface point towards the users and a dedicated egress interface attached to the firewall on a dmz. That way any nat-rules can remain unchanged.
    Another option, depending on your topology, would be a bridge-mode implementation, basically deploying the ACE as a bumb-in-road between the firewall-dmz and the proxies.
    Anyway, just my thought. Hope you find 'em useful.
    /Ulrich

  • EJB deployment issue in websphere

    EJB deployment issue in websphere
    I have created an EJB project in eclipse and created a stateless session bean successfully.
    I created Enterprise application project and added the EJB project.
    I tried to check it using Universal test client.
    When I click the JNDI explorer>>sample.HelloWorldEJBHome
    I get error IWAD0401E Unknown type of JNDI object
    But when I install an EJB jar using administrator console after exporting the jar file for the EJB project
    It is working file
    I like to reduce the number of steps by right clicking the server publish and test.
    Do any one have come across the same issue please help me
    Thanks in advance.

    Hi,
    i have not done any changes to any process. I have created new DC and created new process.
    new DC is not getting deployed with error "Adapter com.sap.glx.adapter.internal.Transformer didn't comply with configuration". If you will check error log above then you will find it their.

  • ACE MAXCONNS issue

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0in 5.4pt 0in 5.4pt;
    mso-para-margin:0in;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;
    mso-bidi-font-family:"Times New Roman";
    mso-bidi-theme-font:minor-bidi;}
    Hi,
    This is with regards to my customer who is facing the following problem with Maxconns – “we are using TCP probes and MaxConn and MinConn are used to determine when a server is busy or not.
    If the MaxConn is exceeded then busy server trips in and stops when the number of TCP sessions drop below MinConn.
    However, we have a situation where if MaxConn is exceeded counting of TCP connections stops and the connections never come down.”
    Customer has A2(1.4a) currently deployed in its network. On perusing the release notes I came across this bug CSCsy30440/CSCsy04371 - ACE: rservers may not accept conns even though they are out of maxconns. I am wondering if this is the issue that they might be facing currently.
    Will this issue be resolved for them if I recommend that they move to A2(1.6a) or A2(2.3) release ?
    Is there a workaround for this other than configuring a backup serverfarm which my customer already has configured? Would it make a difference if they used HTTP probes instead of TCP probes?
    Also is there a way to simulate the connection count behavior using HTTP probes?
    Would really appreciate some help with this issue.
    Thanks & Regards
    Vidhya Nair

    Vidhya,
    you have to open a tac service request so that we can collect the necessary information with the lbinspect tool.
    If you don't want to do any troubleshooting, simply upgrade to the latest version and see if that helps.
    Gilles.

  • Adobe Creative Cloud Enterprise Deployment Issues using SCCM 2012 R2

    Hi,
    I have been trying to deploy Adobe Creative Cloud Enterprise to Windows 8.1 machines that are identical, using SCCM 2012 R2.
    The Adobe package seems fine, because it seems to deploy successfully to some machines. And SCCM 2012 R2 has been configured correctly, as I can deploy other software using it, and again, it deploys Adobe CC successfully to some of the machines.
    I have tried comparing the package that is downloaded on the test machine/client machine, with the original package on the distribution point, using Beyond Compare, and there are no differences.
    I have contacted Adobe Enterprise Support, and they asked me to send to them log files from Event Viewer, the msi installer, and other Adobe logs, from the machine that failed the deployment. However, after Adobe studying them, they told me that they could not identify any problems... Strange, because I could have sworn that I saw error 1603 pop up over 20 times on different machines indicating that the 'Set-up.dat' file had a problem with it.
    After all the testing on over 20 identical machines (same hardware/same software), using different configurations on SCCM 2012 R2 and the client machines, I still can't seem to have a reliable solution to deploying Adobe CC.
    The fact that it deploys successfully on one machine and fails on another, or sometimes deploy to two machines and fail on another (simultaneously), is something that I don't understand.
    Another thing is that, if I retry the deployment 10-15 times after it failed the first time, it might go through...
    Adobe Enterprise Support asked me if they could remote into a machine that failed the deployment to have a look at it and I agreed to that option, but it seems like my issue has been ignored because they never got back to me.
    Has anyone had this kind of problem or anything similar before?
    I need to be able to deploy this remotely to 100+ machines. So installing manually is not an option.
    Any help is appreciated.
    This was posted in the wrong section a few days ago. I'm hoping I can get some help here.
    Case Number: 1862659812
    UPDATE: I spoke to Adobe Customer Support and after 1.5 hours on the phone with a remote session going on, problem was still not solved or identified. Additional log files have been sent and now I'm waiting for a call back.

    Hi Robert,
    We seem to be having a very similar issue.  Our installs would randomly fail with error code 1603 and an error message about a fault in Set-up.dat.  Failure rate was near 95% on our 900 machines.  Adobe Support and Karl having been looking into our issues but so far no solution has been found.
    Having done a lot of investigating we've managed to deploy our package using a schedule task running as a domain admin.  This is a nasty solution and we don't intend on using this permanently, but we needed to get the package out.
    Are you seeing any of the following:
    Entries in PDApp.log:
    [FATAL] |  | ASU | DeploymentManager | DeploymentManager |  |  | 2900 | The Bootstrapper Process is (5).Stopping the installation process.
    [FATAL] |  | ASU | DeploymentManager | DeploymentManager |  |  | 2900 | The return code from the Adobe Installer Process is (33).Stopping the uninstallation process.
    [WARN] |  | ASU | DeploymentManager | DeploymentManager |  |  | 2900 | Failed to find the pdb database.
    [WARN] |  | ASU | DeploymentManager | DeploymentManager |  |  | 2900 | Failed to get the local payload database handle.
    Event Log:
    Faulting application name: Set-up.dat, version: 2.9.1.474, time stamp: 0x54e11f94
    Faulting module name: Set-up.dat, version: 2.9.1.474, time stamp: 0x54e11f94
    Exception code: 0xc0000005
    Fault offset: 0x000d7c52
    Faulting process id: 0xb40
    Faulting application start time: 0x01d072a073861622
    Faulting application path: \\server.name.path\Adobe CC\FullPackage\Build\ASU\Set-up.dat
    Faulting module path: \\server.name.path\Adobe CC\FullPackage\Build\ASU\Set-up.dat
    Report Id: c86d9216-de93-11e4-8284-782bcb99e284
    Faulting package full name:
    Faulting package-relative application ID:
    Installer Log
    Indicates it can't find the Media_db.  We noticed that the folder C:\Program Files (x86)\Common Files\Adobe\caps doesn't get created on the machines were the install fails, so error message is correct in that there isn't a Media_db.db.  Sysinterals Process Monitor seems to show that the setup tried to create the folder/files but they don't actually get created.  Copying a Media_db into the folder from another machine seems to allow the installation to almost finish, but unsurprisingly you end up with problems later on.

Maybe you are looking for

  • What is new in Nokia 6500s update firmware ver. 6....

    What is new in Nokia 6500s update firmware ver. 6.6? Nokia N73. V 4.0812.4.0.1 Code: 0529786 Nokia 6500 Slide V6.6 code: 0556234

  • What is it with yield() that I don't understand?

    The following code starts a thread that awaits a notification that never comes. However, I was expecting the Foo main thread to enter the running state again sometime after it yields and print the last line "main running again", but not so. The progr

  • Uploading a PDF form to the internet

    I have a program that users can download from my website, but I want to keep track of who is downloading it. I've created a simply form in LiveCycle, gathering the basic information. What I want to happen is when a user clicks on the download link, t

  • VGA Cable (Not Adapter)

    My iBook is used as a desktop machine, connected to an external 17" panel via the VGA adapter which Apple supply. The Apple VGA Adapter is only a couple of inches long and so you end up with an ugly VGA plug hanging down from the iBook. Does anyone k

  • Modification of program LRRSVF20

    Hi Experts, I am applying doc "How to....Report Data in Alternate Units of Measure" in BW3.5 Can you mention OSS Note to modify program LRRSVF20 for unit conversion? Useful answer will be rewarded with suitable points. Thanks in advance! Sapna