ACE: SSL termination, Probe and Redirect problem
Hello,
I have problem with three things: -1) SSL offload, -2) probe, and -3) server redirect.
1) I made SSL offload like shows attached file with "show run". But during going to the VIP address by the browser: https://192.168.254.143 I get window with Java error: java.lang.NullPointerException - I have to click OK on this window and then can work fine. Without SSL offload I don't have this error message in window.
When I have SSL offload I have following configuration:
ssl-proxy service SSL
key klucz.pem
cert certyfikat.pem
serverfarm host SFARM
rserver S1 8080
rserver S2 8080
policy-map multi-match SLB-POLICY
class SLB
ssl-proxy server SSL
Without SSL offloading I have only this:
serverfarm host SFARM
rserver S1 (without 8080!)
rserver S2
2) Right now I have two real servers and I send traffic to them by port TCP 8080. So I made probe to check TCP 8080 port availability.:
probe tcp TCP_8080
port 8080
interval 15
passdetect interval 60
serverfarm host SFARM
rserver S1 8080
probe TCP_8080
inservice
rserver S2 8080
probe TCP_8080
inservice
I want also check port TCP 6400 availability, and I only one from port 8080 or 6400 don't work - make real server unavailable. So must work TCP port 8080 ang 6400 togethet to treat real server as operational.
So I want to make something like this:
probe tcp TEST
port 8080 and 6400 !?! - ofcourse It is impossible but I want to make config with this functionality.
How to do this?
3) I hant to make that when I write in browser https://bo.kw.coig.biz/ = https://192.168.254.143 I want to be redirected to one of real server on address: https://bo.kw.coig.biz/businessobjects/enterprise115/desktoplaunch/InfoView/logon/logon.do
I made something like this:
rserver redirect S3
webhost-redirection https://%h/businessobjects/enterprise115/desktoplaunch/InfoView/logon/logon.do 302
inservice
serverfarm redirect REDIRECT
rserver S3
inservice
policy-map type loadbalance first-match POLICY-TYPE
class class-default
serverfarm REDIRECT
But this configuration dosn't work. I have in browser window with error messeging.
How to do this?
1/ this is a java problem.
Java is telling you that it attempted to use a null pointer. You need to check with the people who created the java program
2/ you can configure multiple tcp probe, one for each port you need to monitor and assign all the probes to the serverfarm.
BTW, you can assign the problem to the entire serverfarm so you don't need to specify it for each rserver.
3/ the problem with your redirect is that you applied to class-default.
So even a request to ...../logon will be redirected to ...../logon.
Therefore you just created a nice loop.
You need to create a class-map to only match the url "/" so the redirect is only applied then.
Gilles.
Similar Messages
-
Hello Friends,
Need ur help on cisco ACE SSL termination.
If i import the certificate and key (.PEM), where this files will be saved ?
can we able to download the .PEM file any time as we need(back-up)?
suppose if my .PEM is got hacked, hacker is sniffing the data packet which going through the web server, can it be possiable to deencrypt the packet and see the exact packet ?
Regards,
NarenNaren,
1. In order to import certs and keys, please see the following link to the command reference. To summarize, any time you import/export/delete keys/certs, you are doing so via commands in exec mode. Regarding how and where the ACE actually saves this information, I do not know this answer.
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/ace/v3.00_A2/command/reference/execmds.html#wp1616651
2. You can import a key as non-exportable if you do not want it to be able to be exported. If you import it as exportable, you can always export it later for backups or what not.
3. You can decrypt captured HTTPS traffic if you have the private key. It is important to limit access to it. Please see this link for more info on using Wireshark to view decrypted HTTPS traffic: http://wiki.wireshark.org/SSL
Hope this helps!
Regards,
Matt -
ACE SSL Terminator doesn't work
Hi,
I should implement a balancing HTTP and for HTTPS an SSL terminator on my ACE.
Public IP 22.235.121.6 port 80 --> balanced on 192.168.250.165-166 on port 8889
Public IP 22.235.121.6 port 443 --> my ace terminate ssl and balance the traffic in clear text to 192.168.250.165-166 on port 8889
This is the configuration:
probe http EXAMPLE_IT_HTTP
port 8889
interval 5
faildetect 2
passdetect interval 10
passdetect count 2
request method get url /probe/probe.html
expect status 200 206
expect status 300 307
open 1
serverfarm host example_IT_HTTP
failaction reassign across-interface
predictor leastconns
probe example_IT_HTTP
fail-on-all
rserver H-192.168.250.165 8889
inservice
rserver H-192.168.250.166 8889
inservice
serverfarm host example_IT_HTTPS-HTTP
failaction reassign across-interface
predictor leastconns
probe example_IT_HTTP
fail-on-all
rserver H-192.168.250.165 8889
inservice
rserver H-192.168.250.166 8889
inservice
sticky ip-netmask 255.255.255.255 address both example-IT-HTTPS-HTTP
timeout 60
replicate sticky
serverfarm example_IT_HTTPS-HTTP
ssl-proxy service SSL_example_IT
key example_it.key
cert example_it.cert
chaingroup SSL_CHAIN_example_IT
crypto chaingroup SSL_CHAIN_example_IT
cert example_it.ca
class-map match-all example_IT_HTTP
2 match virtual-address 22.235.121.6 tcp eq www
class-map match-all example_IT_HTTPS-HTTP
2 match virtual-address 22.235.121.6 tcp eq www
policy-map type loadbalance first-match example_IT_HTTP-l7slb
class class-default
serverfarm example_IT_HTTP
policy-map type loadbalance first-match example_IT_HTTPS-HTTP-l7slb
class class-default
sticky-serverfarm example-IT-HTTPS-HTTP
policy-map multi-match int41
class example_IT_HTTP
loadbalance vip inservice
loadbalance policy example_IT_HTTP-l7slb
loadbalance vip icmp-reply active primary-inservice
class example_IT_HTTPS-HTTP
loadbalance vip inservice
loadbalance policy example_IT_HTTPS-HTTP-l7slb
loadbalance vip icmp-reply active primary-inservice
ssl-proxy server SSL_example_IT
the balancing on http work properly, but doesn't work the ssl termination, when I try to connect from my client in https I don't see request on the server 192.168.250.165-166 coming.
Some show:
balancer# sh crypto certificate all
example_it.cert:
Subject: /C=GB/ST=United Kingdom/L=London/O=XXXXXXXX/OU=XXXXXXXXX/CN=*.xxxx.com
Issuer: /C=US/O=Symantec Corporation/OU=Symantec Trust Network/CN=Symantec Class 3 Secure Server CA - G4
Not Before: Apr 11 00:00:00 2014 GMT
Not After: Apr 12 23:59:59 2015 GMT
CA Cert: FALSE
example_it.ca:
Subject: /C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=(c) 2006 VeriSign, Inc. - For authorized use only/CN=VeriSign Class 3 Public Primary Certification Authority - G5
Issuer: /C=US/O=VeriSign, Inc./OU=VeriSign Trust Network/OU=(c) 2006 VeriSign, Inc. - For authorized use only/CN=VeriSign Class 3 Public Primary Certification Authority - G5
Not Before: Nov 8 00:00:00 2006 GMT
Not After: Jul 16 23:59:59 2036 GMT
CA Cert: TRUE
balancer# sh crypto session
SSL Session Cache Stats for Context
Number of Client Sessions: 0
Number of Server Sessions: 0
balancer#
balancer# sh crypto files
Filename File File Expor Key/
Size Type table Cert
cisco-sample-cert 1082 PEM Yes CERT
cisco-sample-key 887 PEM Yes KEY
example_it.ca 7444 PEM Yes CERT
example_it.cert 1812 PEM Yes CERT
example_it.key 1675 PEM Yes KEY
balancer#
balancer# crypto verify example_it.key example_it.cert
Keypair in example_it.key matches certificate in example_it.cert.
balancer#
the show stats crypto client/server give me all 0
Someone can help me to understand why is not working ?
for further information please ask me
Thanks a lotHi,
The problem is here:
class-map match-all example_IT_HTTPS-HTTP
2 match virtual-address 22.235.121.6 tcp eq www
You should change it to 443 instead of WWW which means port 80.
You will never match this class "example_IT_HTTPS-HTTP".
Regards,
Kanwal
Note: Please mark answers if they are helpful. -
ACE - SSL Termination is not working
HTTPS is not working from official IE browser but it is working from test Firefox browser. However HTTP is working with both IE and Firefox browsers. This is true for multiple implementations on the ACE service module with SSL termination.
ACE software 3.0(0)A1(4a)
IE v6 SP3 Cipher 128
Firefox v3.6.3
Sample configuration:
access-list FT ethertype permit bpdu
access-list ALL-ACCESS extended permit icmp any any
access-list ALL-ACCESS extended permit ip any any
crypto chaingroup ROOT-CERT
cert abc.PEM
cert xyz.PEM
parameter-map type ssl SSL-PARAMETER-1
cipher RSA_WITH_RC4_128_MD5
cipher RSA_WITH_RC4_128_SHA
cipher RSA_WITH_AES_128_CBC_SHA priority 2
cipher RSA_WITH_AES_256_CBC_SHA
cipher RSA_EXPORT1024_WITH_DES_CBC_SHA
parameter-map type ssl SSL-PARAMETER-2
cipher RSA_WITH_AES_128_CBC_SHA priority 2
ssl-proxy service SSL-1
key KEY-1.PEM
cert CERT-1.PEM
chaingroup ROOT-CERT
ssl advanced-options SSL-PARAMETER-1
ssl-proxy service SSL-2
key KEY-1.PEM
cert CERT-1.PEM
chaingroup ROOT-CERT
ssl advanced-options SSL-PARAMETER-2
ssl-proxy service SSL-3
key KEY-1.PEM
cert CERT-1.PEM
chaingroup ROOT-CERT
rserver host server1
ip address 10.100.15.89
inservice
rserver host server2
ip address 10.100.15.121
inservice
probe http PROBE-1
interval 30
faildetect 2
request method get url /keepalive.htm
expect status 200 200
serverfarm host SERVERFARM-1
probe PROBE-1
rserver server1 80
inservice
rserver server2 80
inservice
sticky ip-netmask 255.255.255.255 address both STICKY-1
timeout 30
replicate sticky
serverfarm SERVERFARM-1
class-map type management match-any REMOTE-ACCESS
match protocol icmp any
match protocol snmp any
match protocol ssh any
match protocol https any
class-map match-all VIP-1
match virtual-address 10.100.15.140 tcp eq https
class-map match-all VIP-2
match virtual-address 10.100.15.140 tcp eq www
policy-map type management first-match REMOTE-ACCESS
class REMOTE-ACCESS
permit
policy-map type loadbalance first-match POLICY-1
class class-default
sticky-serverfarm STICKY-1
policy-map multi-match LB-1
class VIP-1
loadbalance vip inservice
loadbalance vip icmp-reply active
loadbalance policy POLICY-1
ssl-proxy server SSL-1
(i have tried with ssl-proxy server SSL-2 and ssl-proxy server SSL-3 but did not helP)
policy-map multi-match LB-2
class VIP-2
loadbalance vip inservice
loadbalance vip icmp-reply active
loadbalance policy POLICY-1
interface vlan 15
description client vlan
bridge-group 15
mac-sticky enable
access-group input FT
access-group input ALL-ACCESS
access-group output ALL-ACCESS
service-policy input REMOTE-ACCESS
service-policy input LB-1
service-policy input LB-2
no shutdown
interface vlan 2015
description server vlan
bridge-group 15
mac-sticky enable
access-group input FT
access-group input ALL-ACCESS
access-group output ALL-ACCESS
service-policy input REMOTE-ACCESS
no shutdown
interface bvi 15
description bridge group
ip address 10.100.15.5 255.255.255.0
peer ip address 10.100.15.6 255.255.255.0
alias 10.100.15.4 255.255.255.0
no shutdown
ip route 0.0.0.0 0.0.0.0 10.100.15.1
note: Subnet, Server Name, Certificate Name and Key Name are modified for security reason.Hello,
We will not be able to determine why your SSL terminated connections fail with only your config. You may want to take a look at a similar thread where someone else was having problems with IE and SSL termination, but Firefox worked fine. It also includes a solid action plan you can use to gather data needed to diagnose root cause. That thread can be viewed at the following link:
https://supportforums.cisco.com/thread/2025417?tstart=0
Also, the ACE software you are running is extremely old now and very buggy. I would strongly urge you to upgrade to A2(2.4) as soon as possible. It will help you avoid some headaches as you move forward.
Hope this helps,
Sean -
ACE SSL - Modifying certs and keys
I'm having a problem updating the certs and keys I have in my ssl-proxy service.
My cert is about to expire and I've purchased a new cert. I've uploaded the new cert and key, but I still see the old cert when I go to the VIP with my browser. I thought that by deleting the proxy-service and re-adding I could get the ACE to recognize that it's got new certs but that didn't seem to work.
Is there a trick to make the ACE see the new certs? Does it cache the certs instead of reading them from flash? What's going on here.
Thanks!I changed my certs hot while the application was still running worked like a charm.
What i did was.
- import the new certificate into the crypto store (pkcs12)
- prepare a textfile with the necessary commands
no key old
key new
no cert old
cert new
- paste the commands into the running config.
I had several Customers and Application Admins test the App. while i was changing certs. They didn't even notice something happened. After approx. 60 seconds all new connections were using the new cert old connections were using the old cert. No trouble at all.
And yes the ACE caches the certs if i am not mistaken.
If you want to make sure that it works just create a test context or try it on a test farm first. That's what i did prior to changing the certs and the config on the production enviroment.
Hope it helps.
Roble -
ACE: HTTP followed by HTTPs/SSL termination, stickiness
Dear Helpers,
I'm trying to figure out the best sticky/persistence method for the following for ACE,
Client X ----(HTTP)--------------------------------------------ACE LB ---to----Server 1
Client X -----(HTTPs)---ACE/SSL termination ------ACE LB ---to---- Server1
Both HTTP and HTTPs use the same VIP for HTTP and HTTPs)
The same client to stick/persist to the same server using both HTTP and HTTPs. HTTPs/SSL is terminated by ACE.
Could you point me to sample configurations for this requirement, please.
Thank you
SSHI Gilles,
thanks for the response. Sorry had gotten distracted with a bunch of other things, didn't get a chance to get back to this. Anyway, so, I can generate the 302 response in my web-servers except I need to turn it around to a different domain name. Now assuming I use URL re-write when I see this coming back from the web-server, I can rewrite this to https and send to the client? A few questions about this and the links you sent above with using redirect service.
a) can I do a a redirect to an https address or does it only do http (considering I only saw examples configs only using www.domain.com/index.html type redirects without specifying the protocol to use)?
b) If not, then I use URL rewrite in conjunction with the 302 from the web-servers. But for my SSL off-load in a pair of CSS using VIP and Virtul Interface redundancy, do I buy 2xSSL Certs for the same domain-name or do I buy ONE (i.e. generate the key-pair/CSR in Master CSS) and import the same rsakey and SSL Cert recd. from CA into both CSSs?
c) Does the CSS handle a wildcard SSL Cert without problems?
Thanks again,
\R -
I have a client that will not use my domain in connectivity to an application I am hosting. They want to add an entry in thier DNS using thier domain, but resolve it to an address that I have configured as a VIP on my CSS. I am terminating SSL for this particular VIP and have multiple clients already connecting to this same VIP. Since I can't associate multiple certificates with a single VIP I was wondering is there a way that I can give this one client a seperate VIP and terminate the client certificate on my CSS and then rewrite the host header to look like my domain and hit the same VIP that all my other clients are hitting with the rewritten url.
So the client will input https://www.abc.com and it will resolve to 174.10.10.1 (VIP). The CSS will decrypt the SSL change the header to https://xyz.net which will resolve to 174.10.20.1 (leveraged VIP that all my other clients hit).
If the url rewrite won't work could I use the SSL initiate commands to make this work. My goal is to allow the client to use thier own domain in thier browser, but when it hits my backend servers it has to be from my hosted domain.Good afternoon,
I'm not sure to understand why you need to rewrite the host header or send the request back to the other VIP.
Since you are doing SSL termination, the backend connection (the one between the CSS and the server) will be using HTTP, so, the domain name would not have any impact.
What you should do is create a new SSL termination VIP and map it to the same HTTP content rule or server.
Don't hesitate to contact me again if you need further explanation on this.
Regards
Daniel -
SSL termination and URL redirection
Hi All,
I have configured application in cisco ACE module for which i got more requirement for URL redirection.
Application setup is as below.
VIP : 10.232.92.x/24 which is pointing to 2 Web server 10.232.94.x/24 range. In addition to that app team want APP server also need to be loadbalanced hence new VIP is configured for 10.232.92.x/24 which is pointing to 2 different app server 10.232.94.x/24.
Both Web and App servers are having different IP but in same broadcastdomain. SSL termination is done on ACE.
Issue : 1) After initiating connection i am getting login page but after login its again giveing login page. After 2 to 3 trial its giving me application page but with invalid session error.
2) How to do https connection redirecting to different path.
Ex. https://apps.xyz.com to https://apps.xyz.com/abc
configuration :
probe tcp rem_app_tcp
port 2100
interval 5
passdetect interval 10
passdetect count 2
open 1
probe http rem_itsm_https
port 80
interval 5
passdetect interval 10
passdetect count 2
request method get url /keepalive/https.html
expect status 200 200
open 1
serverfarm host app_tcp
predictor leastconns
probe rem_app_tcp
rserver server1 2100
inservice
rserver server2 2100
inservice
serverfarm host rem_https
predictor leastconns
probe rem_itsm_https
rserver server3 80
inservice
rserver server4 80
inservice
action-list type modify http remurlrewrite
ssl url rewrite location "apps\.xyz\.com"
policy-map type loadbalance first-match app_tcp
class class-default
serverfarm app_tcp
policy-map type loadbalance first-match app_https
class class-default
serverfarm rem_https
action remurlrewrite
class-map match-all VIP_rem_app_tcp
2 match virtual-address 10.232.92.8 any
class-map match-all VIP_rem_itsm_https
2 match virtual-address 10.232.92.9 tcp eq https
class-map match-all real_servers_vlan273
2 match source-address 10.232.94.0 255.255.255.0
policy-map multi-match VIPS
class real_servers_vlan273
nat dynamic 1 vlan 273
class VIP_rem_app_tcp
loadbalance vip inservice
loadbalance policy rem_app_tcp
loadbalance vip icmp-reply
class VIP_rem_itsm_https
loadbalance vip inservice
loadbalance policy rem_itsm_https
loadbalance vip icmp-reply
ssl-proxy server Remedy-SSL-PROXYHi Kanwaljeet,
I have applied below config for HTTPS URL redirection. Seems it dint work for me. Redirect serverfarm and policy map was not hitted.
access-list ANY line 8 extended permit ip any any
probe tcp rem_app_tcp
port 2100
interval 5
passdetect interval 10
passdetect count 2
open 1
probe http rem_itsm_https
port 80
interval 5
passdetect interval 10
passdetect count 2
request method get url /keepalive/https.html
expect status 200 200
open 1
ip domain-name nls.jlrint.com
ip name-server 10.226.0.10
ip name-server 10.226.128.10
rserver redirect REDIRECT-TO-HTTPS
webhost-redirection https://%h/arsys 301
inservice
rserver host serv1
ip address 10.232.94.74
inservice
rserver host serv2
ip address 10.232.94.75
inservice
rserver host serv3
ip address 10.232.94.76
inservice
rserver host serv4
ip address 10.232.94.77
inservice
serverfarm redirect REDIRECT-SERVERFARM
predictor leastconns
rserver REDIRECT-TO-HTTPS
inservice
serverfarm host rem_app_tcp
predictor leastconns
probe rem_app_tcp
rserver serv1 2100
inservice
rserver serv2 2100
inservice
serverfarm host rem_itsm_https
predictor leastconns
probe rem_itsm_https
rserver serv3 80
inservice
rserver serv4 80
inservice
ssl-proxy service Remedy-SSL-PROXY
key Remkey.pem
cert Remcert.pem
class-map type management match-any MANAGEMENT_CLASS
3 match protocol ssh any
4 match protocol snmp any
5 match protocol icmp any
6 match protocol http any
7 match protocol https any
class-map match-all VIP_rem_app_tcp
2 match virtual-address 10.232.92.8 any
class-map match-all VIP_rem_itsm_http
2 match virtual-address 10.232.92.9 tcp eq www
class-map match-all VIP_rem_itsm_https
2 match virtual-address 10.232.92.9 tcp eq https
class-map match-all real_servers_vlan273
2 match source-address 10.232.94.0 255.255.255.0
policy-map type management first-match MANAGEMENT_POLICY
class MANAGEMENT_CLASS
permit
policy-map type loadbalance first-match REDIRECT-PM
class class-default
serverfarm REDIRECT-SERVERFARM
policy-map type loadbalance first-match rem_app_tcp
class class-default
serverfarm rem_app_tcp
policy-map type loadbalance first-match rem_itsm_https
class class-default
serverfarm rem_itsm_https
policy-map multi-match VIPS
class real_servers_vlan273
nat dynamic 1 vlan 273
class VIP_rem_itsm_http
loadbalance vip inservice
loadbalance policy REDIRECT-PM
class VIP_rem_itsm_https
loadbalance vip inservice
loadbalance policy rem_itsm_https
loadbalance vip icmp-reply
ssl-proxy server Remedy-SSL-PROXY
class VIP_rem_app_tcp
loadbalance vip inservice
loadbalance policy rem_app_tcp
loadbalance vip icmp-reply
interface vlan 270
description VIP
ip address 10.232.92.4 255.255.255.0
alias 10.232.92.6 255.255.255.0
peer ip address 10.232.92.5 255.255.255.0
access-group input ANY
service-policy input MANAGEMENT_POLICY
service-policy input VIPS
no shutdown
interface vlan 273
description Real server
ip address 10.232.94.66 255.255.255.192
alias 10.232.94.65 255.255.255.192
peer ip address 10.232.94.67 255.255.255.192
access-group input ANY
nat-pool 1 10.232.92.253 10.232.92.253 netmask 255.255.255.0 pat
service-policy input MANAGEMENT_POLICY
service-policy input VIPS
no shutdown -
We have moved SSL termination to a loadbalancer (F5) from the Sun webservers. The load balancer after terminating SSL goes to the http listener on the webservers. We have some NSAPI code that does a redirect. It used to do the redirect based on the original scheme of the listener (if http then the redirect was http based. If https then redirect https). Of course, now all redirects come back http even though the user may have an https session.
For weblogic we can feed a header from the F5 (WL-PROXY-SSL) and it would recognize that a load balancer was used for SSL termination and perform java redirects using the correct scheme. Is there any header like this I can feed to the Sun Webserver so it recognizes that a loadbalancer has terminated the SSL session and any redirects should be https?It might be easiest to configure separate HTTP listeners (e.g. separate ports) for SSL and non-SSL requests. You can configure which scheme should be used in self-referencing URLs (such as those used in redirects) per HTTP listener. In Sun Java System Web Server 7.0, you can do that using the admin GUI, CLI, or by editing the server.xml configuration. If you edit server.xml, you need to specify the <server-name> element in the appropriate <http-listener> element.
-
SSL Termination not working in ACE
Hi,
The context was configured for Load Balancing Port 80 and 443 traffic before the SSL Configs was Applied.
The SSL Termination is configured on ACE module running the software version A2(1.6a) [build 3.0(0)A2(1.6a)
The load balacing is working without no issues, But when i do a https://abc.www.abc.qa/wps/portal/login
the browser reconganizes the certificate from ACE, but does not show up any thing, just shows this symbol €
in a blank page.
Plese let me know if you have any suggestions.
Thanks in Advance.
Here is the relevant config.
===================
crypto csr-params ABC-II-PRAMS
country XX
state XXXX
locality XXXX
organization-name abc council
common-name abc.www.abc.qa
serial-number 1
email [email protected]
rserver host abcserver1
ip address 10.14.1.165
inservice
rserver host abcserver2
ip address 10.14.1.177
inservice
ssl-proxy service abc.www.proxy
key abc-II-key.pem
cert abc-II-cert.pem
serverfarm host abc.www.abc.qa-443
failaction purge
rserver abcserver1
probe abcicmp
inservice
rserver abcserver2
probe abcicmp
inservice
serverfarm host abc.www.abc.qa-80
failaction purge
rserver abcserver1
probe abcicmp
inservice
rserver abcserver2
probe abcicmp
inservice
sticky ip-netmask 255.255.255.255 address source abc.www.abc.qa-sticky-80
timeout 120
serverfarm abc.www.abc.qa-80
sticky ip-netmask 255.255.255.255 address source abc.www.abc.qa-sticky-443
timeout 120
serverfarm abc.www.abc.qa-443
class-map match-all abc.www.abc.qa-443
match virtual-address 10.14.1.203 tcp eq https
class-map match-all abc.www.abc.qa-80
match virtual-address 10.14.1.203 tcp eq www
policy-map type loadbalance first-match abc.www.abc.qa-VIP-443
class class-default
sticky-serverfarm abc.www.abc.qa-sticky-443
policy-map type loadbalance first-match abc.www.abc.qa-VIP-80
class class-default
sticky-serverfarm abc.www.abc.qa-sticky-80
policy-map multi-match abc-POLICY
class abc.www.abc.qa-80
loadbalance vip inservice
loadbalance policy abc.www.abc.qa-VIP-80
loadbalance vip icmp-reply
class abc.www.abc.qa-443
loadbalance vip inservice
loadbalance policy abc.www.abc.qa-VIP-443
loadbalance vip icmp-reply
ssl-proxy server abc.www.proxy
=============================Hi,
You may want to check this thread I think it would be very helpful.
https://supportforums.cisco.com/thread/2027253
HTH
Pablo
Cisco TAC -
SSL Termination in ACE 4710 not working
Hi,
I have configured a new ACE 4710 with only a sinlge context to redirect https traffic to http real servers using SSL Termination. When I do a telnet on port 443 or 80 to the VIP it works fine but when I try to open the URL it prompts me for accepting the certificate then it tries to find and establish connection to the URL but eventually dies out giving a "Page cannot be displayed error". I have done some troubleshooting and found that the connection to the VIP on 443 port is Established but the out connection from the real server to the client remains in the INIT state. I am attaching the configs and all the troubleshooting data I have collected. Pls someone help.Yes the "server pkt count" for the "class: VIP_HTTPD_Redirect" is not incrementing and yes the servers do not have the default gateway towards the ACE.So as suggested I have configured default route in the servers towards the ACE interface vlan ip address. Still the server packet count is not incrementing. I am posting the updated configuration of the ACE as an attachment. Pls help.
-
ACE module SSL url rewrite and path rewrite
Hi all,
I'm hoping some of you helpful people on this forum can guide me or suggest a solution to a problem I'm faced with.
I am currently load balancing exchange 2010 traffic via an ACE module. Software version is A2(3.3). I have most parts of it working fine however I am having an issue when it comes to SSL termination for Outlook Web Access (OWA).
The problem comes down to a HTTP header (field is location). I have configured an action list to re-write the SSL pure URL as per page 96 of the "Cisco Application Control Engine Module SSL Configuration Guide". example:
ssl url rewrite location bnecas\.mycompany\.com sslport 443
That part works, the http header location field that comes back from the GET request is changed to https://cas.mycompany.com which is great. However, in addition to that url, there is also a path or something following that part. The actual string that is returned is:
https://cas.mycompany.com/owa/auth/logon.aspx?url=http://cas.mycompany.com/owa/&reason=0
The first bit of it, (https://cas.mycompany.com) is changed by the ssl url rewrite command, however the last part (http://cas.mycompany.com/owa/&reason=0) isn't changed.
This is where I've been trying to get the http Header Rewrite command to do something. I don't know if it can work in conjunction with the ssl url rewrite function however with the ssl rewrite function it seems it can't change bits of the string that aren't the pure URL at the front.
The end result is that while I have an SSL connection to the OWA login page, when I do login to OWA it reverts back to HTTP. I'm fairly sure it is because of the last part of the location string above. Is there a way to change that location string to do the following:
1. change the first part of the string to be https://cas.mycompany.com (like the ssl url rewrite function)
2. change the last part of the location string to put https in there instead of http
Ideally I would love to have this string
http://cas.mycompany.com/owa/auth/logon.aspx?url=http://cas.mycompany.com/owa/&reason=0
replaced with this one
https://cas.mycompany.com/owa/auth/logon.aspx?url=https://cas.mycompany.com/owa/&reason=0
I had originally tried the following in the action list:
header rewrite response location header-value "(owa/auth/logon\.aspx\?url=)http(://bnecas\.thiess\.aus/owa/&reason=0)" replace "%1https%2"
ssl url rewrite location bnecas\.mycompany\.com sslport 443
but it didn't work. I'm probably screwing up the regex somewhere however there doesn't seem to be very clear examples anywhere I can find.
Any help will be greatly appreciated and of course I will be sure to rate every post that responds to my plea for help.
BradHi Brad,
try this:
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
action-list type modify http X
header rewrite response Location header-value "http://(.*url=)http://(.*)" replace "https://%1https://%2"
we wont be using ssl url rewrite in this case
Also we will be needing persistence rebalance applied through application parameter map and apply that under the VIP class -
ACE http health probes - best practice for interval and passdetect interval?
Hi,
Is there a recommended standard for http health probes in terms of interval and passdetect interval timings, i.e. should the passdetect interval always be less than the interval or visa versa? Can a http probe be 'mis-configured', i.e. return a 'false positive' by configuring an interval timeout thats 'incompatible' with the device it's polling?
I have a http probe for a serverfarm consisting of two Apache http servers and get intermittent 'server reply timeout' probe failures. I'm keen to ensure that the configuration of the probe isn't at fault so I can be confident that a failed probe indicates a problem with the server and not my configuration.
The probe is currently configured as below:-
probe http http-apache
interval 30
passdetect interval 15
passdetect count 6
request method get url /cs/images/ACE.html
expect status 200 304
Any advice on the subject woud be gratefully received.
thanks
MatthewHi Gilles,
Thanks for the advice. In another dicussion (found here https://supportforums.cisco.com/message/462397#462397) a poster has stated that:-
"(The) "Probe interval" should always be less then (open+recieve) timeout value. Default open & receive timeouts are 10 seconds."
Are you able to advise on whether the above is correct and if so, why? I currently have an interval value of 30 that obviously goes against the advice above (which I've interpretted to mean that if you leave the open & receive timeouts at their default settings your probe interval should be less than 20 seconds?).
thanks
Matthew -
ACE 4700 configuring SSL termination weblogic server 10.3.6
Hello,
Im trying to configure an ACE 4700 so that SSL termination is done on the ACE and HTTP reaches the weblogic server instance.
I have a working setup of a Apache reverse proxy doing SSL offloading and using a weblogic module and that works fine
Was reading http://docs.oracle.com/cd/E23943_01/web.1111/e13709/load_balancing.htm#i1045186
Can anyone point me to a working config example for doing this with the ACE4700 or give me some directions here?
Kind regards,
LaurensHi Laurens,
Here is a basic configuration for SSL termination:
rserver host test
ip address 10.198.16.98
inservice
rserver host test2
ip address 10.198.16.93
inservice
serverfarm host test
rserver test 80
inservice
rserver test2 80
inservice
ssl-proxy service TEST
key cert
cert cert
class-map match-all VIPSSL
2 match virtual-address 10.198.16.122 tcp eq https
policy-map type loadbalance first-match test
class class-default
serverfarm test
policy-map multi-match clients
class VIPSSL
loadbalance vip inservice
loadbalance policy test
loadbalance vip icmp-reply active
nat dynamic 1 vlan 112
ssl-proxy server TEST
interface vlan 112
ip address 10.198.16.91 255.255.255.192
access-group input Allow_Access
nat-pool 1 10.198.16.122 10.198.16.122 netmask 255.255.255.192 pat
service-policy input NSS_MGMT
service-policy input clients
no shutdown
Cesar R
ANS Team -
Configuring JMS and loadbalancer with SSL termination? Has Anyone done it?
Hi all,
I'm having a problem getting JMS or even any JNDI lookup to work with a hardware load balancer and SSL termination. Has anyone used such a configuration? The load balancer in question is a Cisco CSS 11500 Series which has an SSL module. A client communicates with the CSS over SSL, the SSL module decrypts the packets and sends it for content switching and on to WebLogic as cleartext.
Without SSL termination everthing works fine. With SSL termination active, Web service and web content all work fine, but I can't get SSL tGetting Initial context from ms01
<29-Sep-2006 16:07:22 o'clock IST> <Debug> <TLS> <000000> <SSL/Domestic license found>
<29-Sep-2006 16:07:22 o'clock IST> <Debug> <TLS> <000000> <Not in server, Certicom SSL license found>
<29-Sep-2006 16:07:23 o'clock IST> <Debug> <TLS> <000000> <SSL Session TTL :90000>
<29-Sep-2006 16:07:23 o'clock IST> <Debug> <TLS> <000000> <Trusted CA keystore: D:/eclipse/workspace/LoadBalancerTest/ssl/keystores/cssKeyS
ore.keystore>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <Filtering JSSE SSLSocket>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.addContext(ctx): 886220>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLSocket will NOT be Muxing>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <write SSL_20_RECORD>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <3941240 received HANDSHAKE>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHello>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <3941240 received HANDSHAKE>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Certificate>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <validationCallback: validateErr = 0>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> < cert[0] = [
Version: V3
Subject: EMAILADDRESS="[email protected] ", CN=10.51.0.200, OU=Web Administration, O=Revenue Commissioners, L=Dublin, ST=Dublin,
=IE
Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
Key: SunJSSE RSA public key:
public exponent:
010001
modulus:
a8f60248 b87c5860 229b9044 a666a9ae 27eb488c 424d9e67 e7b9d6d0 c292f081
cfa76c04 f3d89b28 1bf544f9 5de2b66d 576ebeca 5dc5ca8a fceead9a 52e2ce6c
2b91afef e4da5071 49b8784c 12d7f5f3 99f76482 79efe1d8 0a24f664 4c8d6e9e
b0bc63be 1faf8319 eeb23e8a 019b65b2 59dd086d 1b714d4c 01618804 66f416bb
Validity: [From: Fri Sep 08 11:44:28 BST 2006,
To: Mon Sep 05 11:44:28 BST 2016]
Issuer: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
SerialNumber: [ 0131]
Certificate Extensions: 4
[1]: ObjectId: 2.16.840.1.113730.1.13 Criticality=false
Extension unknown: DER encoded OCTET string =
0000: 04 1F 16 1D 4F 70 65 6E 53 53 4C 20 47 65 6E 65 ....OpenSSL Gene
0010: 72 61 74 65 64 20 43 65 72 74 69 66 69 63 61 74 rated Certificat
0020: 65 e
[2]: ObjectId: 2.5.29.14 Criticality=false
SubjectKeyIdentifier [
KeyIdentifier [
0000: 0E 6E 72 2E B1 3B B6 A3 59 79 5A C5 41 26 B7 B6 .nr..;..YyZ.A&..
0010: A2 39 4C 73 .9Ls
[3]: ObjectId: 2.5.29.35 Criticality=false
AuthorityKeyIdentifier [
KeyIdentifier [
0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
0010: AA 97 05 0D ....
[CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE]
SerialNumber: [ 00]
[4]: ObjectId: 2.5.29.19 Criticality=false
BasicConstraints:[
CA:false
PathLen: undefined
Algorithm: [MD5withRSA]
Signature:
0000: 2C A0 0C 34 4E 0D CA 24 A5 C3 03 3A 71 A1 2D D3 ,..4N..$...:q.-.
0010: 65 A2 FA EF C1 5D D4 4A 28 8C 1A 70 5F 92 73 5E e....].J(..p_.s^
0020: 7B 13 D4 AE 36 A8 86 EA 60 7F A5 E3 86 6E 84 1F ....6...`....n..
0030: 5E 5F 30 06 B4 AA 2E 5C A7 65 74 32 09 0A 91 14 ^_0....\.et2....
]>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> < cert[1] = [
Version: V3
Subject: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
Key: SunJSSE RSA public key:
public exponent:
010001
modulus:
bc61b29f a830c97a 7a76883e 1665a241 a68b891f 8e4167eb 62e578ac 9e342c3e
53c9de8b e756634b e364010f 4d36c1c5 21a65b37 b64b4861 6f4dda29 b932191f
Validity: [From: Mon May 31 15:22:15 BST 2004,
To: Thu May 29 15:22:15 BST 2014]
Issuer: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
SerialNumber: [ 00]
Certificate Extensions: 3
[1]: ObjectId: 2.5.29.14 Criticality=false
SubjectKeyIdentifier [
KeyIdentifier [
0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
0010: AA 97 05 0D ....
[2]: ObjectId: 2.5.29.35 Criticality=false
AuthorityKeyIdentifier [
KeyIdentifier [
0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
0010: AA 97 05 0D ....
[CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE]
SerialNumber: [ 00]
[3]: ObjectId: 2.5.29.19 Criticality=true
BasicConstraints:[
CA:true
PathLen:2147483647
Algorithm: [MD5withRSA]
Signature:
0000: 3C 64 7C 9E 0B 90 48 9D 70 74 06 80 7F 2C AF 73 <d....H.pt...,.s
0010: 92 1C C3 39 DD C3 45 B6 A4 8E 11 27 8E 21 18 4B ...9..E....'.!.K
0020: FD AA 31 5E 35 FC DF 9E 70 42 F4 65 5C DF 56 9A ..1^5...pB.e\.V.
0030: DD 8C 6B B7 3B BE E5 A7 D5 4A 16 23 C1 91 07 CA ..k.;....J.#....
]>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <SSLTrustValidator returns: 0>
<29-Sep-2006 16:07:24 o'clock IST> <Debug> <TLS> <000000> <Trust status (0): NONE>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <Performing hostname validation checks: 10.51.0.200>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 received HANDSHAKE>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHelloDone>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 134>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write CHANGE_CIPHER_SPEC, offset = 0, length = 1>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 16>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 received CHANGE_CIPHER_SPEC>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3941240 received HANDSHAKE>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Finished>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 272>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <3445873 read(offset=0, length=2048)>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3941240 received APPLICATION_DATA: databufferLen 0, contentLength 372>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3445873 read databufferLen 372>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3445873 read A returns 372>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 339>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3445873 read(offset=372, length=1676)>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <Filtering JSSE SSLSocket>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.addContext(ctx): 6771926>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLSocket will NOT be Muxing>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 93>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 SSL3/TLS MAC>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 received HANDSHAKE>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHello>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 SSL3/TLS MAC>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 received CHANGE_CIPHER_SPEC>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 SSL3/TLS MAC>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 received HANDSHAKE>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Finished>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write CHANGE_CIPHER_SPEC, offset = 0, length = 1>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 16>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 402>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 1707>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <23328673 read(offset=0, length=2048)>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 SSL3/TLS MAC>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <3840954 received APPLICATION_DATA: databufferLen 0, contentLength 174>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <23328673 read databufferLen 174>
<29-Sep-2006 16:07:29 o'clock IST> <Debug> <TLS> <000000> <23328673 read A returns 174>
<29-Sep-2006 16:07:44 o'clock IST> <Debug> <TLS> <000000> <NEW ALERT with Severity: WARNING, Type: 0
java.lang.Exception: New alert stack
at com.certicom.tls.record.alert.Alert.<init>(Unknown Source)
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.closeWriteHandler(Unknown Source)
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.close(Unknown Source)
at javax.net.ssl.impl.SSLSocketImpl.close(Unknown Source)
at weblogic.net.http.HttpClient.closeServer(HttpClient.java:466)
at weblogic.net.http.KeepAliveCache$1.run(KeepAliveCache.java:120)
at java.util.TimerThread.mainLoop(Unknown Source)
at java.util.TimerThread.run(Unknown Source)
>
<29-Sep-2006 16:07:44 o'clock IST> <Debug> <TLS> <000000> <avalable(): 23328673 : 0 + 0 = 0>
<29-Sep-2006 16:07:44 o'clock IST> <Debug> <TLS> <000000> <write ALERT, offset = 0, length = 2>
<29-Sep-2006 16:07:44 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.removeContext(ctx): 6771926>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <3941240 SSL3/TLS MAC>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <3941240 received APPLICATION_DATA: databufferLen 0, contentLength 98>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <3445873 read databufferLen 98>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <3445873 read A returns 98>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <Filtering JSSE SSLSocket>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.addContext(ctx): 8406772>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLSocket will NOT be Muxing>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 93>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 SSL3/TLS MAC>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 received HANDSHAKE>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHello>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 SSL3/TLS MAC>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 received CHANGE_CIPHER_SPEC>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 SSL3/TLS MAC>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <21830977 received HANDSHAKE>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Finished>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write CHANGE_CIPHER_SPEC, offset = 0, length = 1>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 16>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 339>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <5618579 read(offset=0, length=2048)>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:08:13 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
Exception in thread "main" javax.naming.CommunicationException [Root exception is java.net.ConnectException: https://10.51.0.200:8143: Boot
trap to: 10.51.0.200/10.51.0.200:8143' over: 'https' got an error or timed out]
at weblogic.jndi.internal.ExceptionTranslator.toNamingException(ExceptionTranslator.java:47)
at weblogic.jndi.WLInitialContextFactoryDelegate.toNamingException(WLInitialContextFactoryDelegate.java:636)
at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:306)
at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:239)
at weblogic.jndi.WLInitialContextFactory.getInitialContext(WLInitialContextFactory.java:135)
at javax.naming.spi.NamingManager.getInitialContext(Unknown Source)
at javax.naming.InitialContext.getDefaultInitCtx(Unknown Source)
at javax.naming.InitialContext.init(Unknown Source)
at javax.naming.InitialContext.<init>(Unknown Source)
at TestAllManagedServers.main(TestAllManagedServers.java:54)
Caused by: java.net.ConnectException: https://10.51.0.200:8143: Bootstrap to: 10.51.0.200/10.51.0.200:8143' over: 'https' got an error or t
med out
at weblogic.rjvm.RJVMFinder.findOrCreate(RJVMFinder.java:200)
at weblogic.rjvm.ServerURL.findOrCreateRJVM(ServerURL.java:125)
at weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialContextFactoryDelegate.java:296)
... 7 more
o work for a simple JNDI lookup. With SSL debugging turned on, the following output is given:
When I compare the Server HTTP logs I see that an initial context lookup involves 3 HTTP requests, e.g.
25.2.1.210 - - [29/Sep/2006:16:29:12 +0100] "GET /bea_wls_internal/HTTPClntLogin/a.tun?wl-login=https+dummy+WLREQS+8.1.5+dummy+%0A&r
and=3018901804201457976&AS=255&HL=19 HTTP/1.1" 200 17
25.2.1.210 - - [29/Sep/2006:16:29:12 +0100] "GET /bea_wls_internal/HTTPClntRecv/a.tun?connectionID=0&rand=7332722597180897050 HTTP/1
.1" 200 2341
25.2.1.210 - - [29/Sep/2006:16:29:12 +0100] "POST /bea_wls_internal/HTTPClntSend/a.tun?connectionID=0&rand=3415396992694182025 HTTP/
1.1" 200 17
When my request goes through the load balancer I see the following in the HTTP logs:
10.51.0.200 - - [29/Sep/2006:16:31:33 +0100] "GET /bea_wls_internal/HTTPClntLogin/a.tun?wl-login=https+dummy+WLREQS+8.1.5+dummy+%0A&
rand=8279752507152372405&AS=255&HL=19 HTTP/1.1" 200 17
10.51.0.200 - - [29/Sep/2006:16:31:33 +0100] "POST /bea_wls_internal/HTTPClntSend/a.tun?connectionID=0&rand=1051450669479197885 HTTP
/1.1" 200 17
10.51.0.200 - - [29/Sep/2006:16:32:28 +0100] "GET /bea_wls_internal/HTTPClntRecv/a.tun?connectionID=0&rand=6035654607615870287 HTTP/
1.1" 200 5
10.51.0.200 - - [29/Sep/2006:16:33:13 +0100] "GET /bea_wls_internal/HTTPClntRecv/a.tun?connectionID=0&rand=8245112057388607005 HTTP/
1.1" 200 5
Notice the time delay in some of the messages.
The following error appears in the WebLogic server log, however I've verified that all IP addresses referenced by the load balancer configuration match those in the WebLogic configuration:
<29-Sep-2006 16:31:43 o'clock IST> <Error> <RJVM> <BEA-000572> <The server rejected a connection attempt JVMMessage from: '266014296
868812899C:25.2.1.210R:2462711729186814398S:10.51.0.2:[8113,8113,8114,8114,8113,8114,-1,0,0]:10.51.0.1:8103,10.51.0.1:8105,10.51.0.1
:8107,10.51.0.2:8109,10.51.0.2:8111,10.51.0.2:8113:risIntCluster01:ms06' to: '0S:10.51.0.200:[-1,-1,-1,8143,-1,-1,-1,-1,-1]' cmd: 'C
MD_IDENTIFY_REQUEST', QOS: '102', responseId: '0', invokableId: '0', flags: 'JVMIDs Sent, TX Context Not Sent', abbrev offset: '228'
probably due to an incorrect firewall configuration or admin command.>
When a JNDI lookup is made directly to a WebLogic server on the https port, the client gives the following output:
Getting Initial context from ms01
<29-Sep-2006 16:29:22 o'clock IST> <Debug> <TLS> <000000> <SSL/Domestic license found>
<29-Sep-2006 16:29:22 o'clock IST> <Debug> <TLS> <000000> <Not in server, Certicom SSL license found>
<29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <SSL Session TTL :90000>
<29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <Trusted CA keystore: D:/eclipse/workspace/LoadBalancerTest/ssl/keystores/cssKeySt
ore.keystore>
<29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <Filtering JSSE SSLSocket>
<29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <SSLIOContextTable.addContext(ctx): 7860099>
<29-Sep-2006 16:29:23 o'clock IST> <Debug> <TLS> <000000> <SSLSocket will NOT be Muxing>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <write SSL_20_RECORD>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <32915800 received HANDSHAKE>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHello>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <32915800 received HANDSHAKE>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Certificate>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <validationCallback: validateErr = 0>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> < cert[0] = [
Version: V3
Subject: CN=10.52.0.3, OU=Revenue Integration Server, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
Key: SunJSSE RSA public key:
public exponent:
010001
modulus:
ac47cae5 45e55fe4 8ec06362 84aab923 af35d7f1 8b7e8aaa 32772d8a d8185106
0ba91363 07162207 6eaa33b4 db8a3fbb 1e228e93 841ff322 e319242a 04ae7447
Validity: [From: Mon May 31 16:45:21 BST 2004,
To: Thu May 29 16:45:21 BST 2014]
Issuer: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
SerialNumber: [ 05]
Certificate Extensions: 4
[1]: ObjectId: 2.16.840.1.113730.1.13 Criticality=false
Extension unknown: DER encoded OCTET string =
0000: 04 1F 16 1D 4F 70 65 6E 53 53 4C 20 47 65 6E 65 ....OpenSSL Gene
0010: 72 61 74 65 64 20 43 65 72 74 69 66 69 63 61 74 rated Certificat
0020: 65 e
[2]: ObjectId: 2.5.29.14 Criticality=false
SubjectKeyIdentifier [
KeyIdentifier [
0000: D7 B3 92 7B C7 4E 2F 5D F3 97 CB 3B F9 FB 0A 1E .....N/]...;....
0010: 97 C5 DD F1 ....
[3]: ObjectId: 2.5.29.35 Criticality=false
AuthorityKeyIdentifier [
KeyIdentifier [
0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
0010: AA 97 05 0D ....
[CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE]
SerialNumber: [ 00]
[4]: ObjectId: 2.5.29.19 Criticality=false
BasicConstraints:[
CA:false
PathLen: undefined
Algorithm: [MD5withRSA]
Signature:
0000: 57 B6 54 4E 1A 54 91 66 5C A8 FE AF B6 50 AB 23 W.TN.T.f\....P.#
0010: 6A 32 42 77 06 44 D5 7D 40 81 E4 DD 84 E3 7B 55 [email protected]
0020: 96 A6 BC E9 E9 51 96 B9 E4 01 56 F9 41 B7 0C C3 .....Q....V.A...
0030: 0A 92 C0 17 6E 6B 9D D6 9A 87 6D 6E 15 5A 86 F4 ....nk....mn.Z..
]>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> < cert[1] = [
Version: V3
Subject: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
Key: SunJSSE RSA public key:
public exponent:
010001
modulus:
bc61b29f a830c97a 7a76883e 1665a241 a68b891f 8e4167eb 62e578ac 9e342c3e
53c9de8b e756634b e364010f 4d36c1c5 21a65b37 b64b4861 6f4dda29 b932191f
Validity: [From: Mon May 31 15:22:15 BST 2004,
To: Thu May 29 15:22:15 BST 2014]
Issuer: CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE
SerialNumber: [ 00]
Certificate Extensions: 3
[1]: ObjectId: 2.5.29.14 Criticality=false
SubjectKeyIdentifier [
KeyIdentifier [
0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
0010: AA 97 05 0D ....
[2]: ObjectId: 2.5.29.35 Criticality=false
AuthorityKeyIdentifier [
KeyIdentifier [
0000: D2 66 DD FC 06 C2 BC 7E 18 D5 64 38 AD 6E D0 0A .f........d8.n..
0010: AA 97 05 0D ....
[CN=Revenue CA, OU=Revenue Certificate Authority, O=Office Of The Revenue Commissioners, L=Dublin, ST=Dublin, C=IE]
SerialNumber: [ 00]
[3]: ObjectId: 2.5.29.19 Criticality=true
BasicConstraints:[
CA:true
PathLen:2147483647
Algorithm: [MD5withRSA]
Signature:
0000: 3C 64 7C 9E 0B 90 48 9D 70 74 06 80 7F 2C AF 73 <d....H.pt...,.s
0010: 92 1C C3 39 DD C3 45 B6 A4 8E 11 27 8E 21 18 4B ...9..E....'.!.K
0020: FD AA 31 5E 35 FC DF 9E 70 42 F4 65 5C DF 56 9A ..1^5...pB.e\.V.
0030: DD 8C 6B B7 3B BE E5 A7 D5 4A 16 23 C1 91 07 CA ..k.;....J.#....
]>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <SSLTrustValidator returns: 0>
<29-Sep-2006 16:29:24 o'clock IST> <Debug> <TLS> <000000> <Trust status (0): NONE>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <Performing hostname validation checks: 10.51.0.1>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 received HANDSHAKE>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: ServerHelloDone>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 70>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write CHANGE_CIPHER_SPEC, offset = 0, length = 1>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write HANDSHAKE, offset = 0, length = 16>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 received CHANGE_CIPHER_SPEC>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 received HANDSHAKE>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <HANDSHAKEMESSAGE: Finished>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 0>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <write APPLICATION_DATA, offset = 0, length = 270>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <30340343 read(offset=0, length=2048)>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <isMuxerActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <SSLFilter.isActivated: false>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLS> <000000> <32915800 SSL3/TLS MAC>
<29-Sep-2006 16:29:28 o'clock IST> <Debug> <TLYou will need an AAM set with the internal (http) address.
http://blogs.msdn.com/b/ajithas/archive/2009/09/11/alternate-access-mapping-in-reverse-proxy-configuration.aspx
Dimitri Ayrapetov (MCSE: SharePoint)
Maybe you are looking for
-
Opening photoshop from double click on file opens the app but doesn't open the file.
This is a new behaviour... how can we solve it? Its very annoying!
-
How do i transfer pictures from ipad 2 to pc
how do i transfer pictures from my ipad 2 to my pc
-
my mac failed a month ago and apple needed to put in a new hard drive, which deleted everything. i need to put music from my iphone to my itunes library, please help?
-
When I opened ASP for a non-related issue in noticed that the VRAM was listed as 48MB when the card (ATI Redeon 9000 Mobile) is supposed to be 64MB. Despite many searches on other froums and on the net I could not find any suggetstions. I reset the P
-
I'm not sure where to post this question, but here goes. Is it possible to reset the audio on my mac so that the sound volume of video clips and movies is raised? I regularly encounter video with audio volume that is too low, even though I have the v