Ace tcp idle timer VERY URGENT!

Hi,
I set the following
parametermap type conection TCP-60sec
set timeout inactivity 60
policy-map multi match Tandem
class POS-33067
loadbalance vip inservice
loadbalance policy POS-33067
loadbalance vip icmp-reply
loadbalance vip advertise
connection advanced-options TCP-60sec
interface vlan 100
service-policy input Tandem
Unfurtunetly this is not affect. after clear conn there will be connections which have more than 60 sec idle timeout.
Very thanks

Hi Karoly,
Please take into account that, as long as one of the sides of the connection (client-to-ace or ace-to-server) is still open, the other one will remain open as well even if the inactivity timeout is higher than what it's configured. This could happen if, for example, one of the sides is using TCP keepalives but the other one is not.
This is just something to check to see if you really have an issue or not. If you need further troubleshooting, I would recommend you to open a TAC case.
Regards
Daniel

Similar Messages

Modify a tcp idle time-out on ACE

Hi.
I have a question about tcp idle-time out on ace.
I configured like below
set timeout inactivity 600000
class-map match-any TCP_Connection_IP
2 match virtual-address 100.254.130.0 255.255.255.0 tcp any
policy-map multi-match TCP_Connection_Policy
class TCP_Connection_IP
connection advanced-options TCP_Connection_Timer
interface vlan 30(Client Vlan)
service-policy input TCP_Connection_Policy
interface vlan 330(Server Vlan)
service-policy input TCP_Connection_Policy
Is it a correct?,
If ok, How can I check the tcp-idle?
as show command,

You can't use the virtual-address keyword if you don't want to loadbalance the traffic.
If you just want to the timeout for traffic routed, you need to use a class-map with an acl.
ie:
access-list net1 extended permit tcp any 100.254.130.0 255.255.255.0
class-map net1
match access-list net1
policy-map multimatch TCP_Connection_Policy
class net1
connection advanced-options TCP_Connection_Timer
Now, if you have multiple virtual ip address and want to set the timeout for this virtual ip, you have to assign the connection timeout to all individual virtual ip.
You can't do it in one shot like you did.
There is no command to see if a connection has the right idle timeout.
All you can do is a 'show conn detail' and see if the idle timeout increases up to your configured value.
Gilles.

Total Relenishment Lead Time vs. Routings Lead Time ( very urgent)

Hello PP Champs
Need urgent help
I am facing a scenario in current project -
My Customer service quotes for delivery to an customer with in 3 days for a stock item by seeing the availability check with Total Replenishment Lead time in MAterial Master , but when production order is created SAP schedules the same on routing Lead time basis with a date after 7 days. this seems technically correct as per Std.SAP settings
1=but How to avoid this business conflict in SAP PP module?
2=another thing we are nt using the capacity planning with this client ,but incase we get 2-3 orders with same start date and same requirement date for a single work center " how to priortise the selection of production orders" w/o capacity planning
pl consider first query as most urgent and help me
Could somebody put a thought on this and help me out.. I'll reward full points any helping hand for the same
Thx in advance
BR
Sumit

Hi,
you can define via define the checking scope opjj whether to include the RLT
in availability check or not.
Note:
Items for which the delivery date falls within the replenishment lead time, but for which there is no inventory, are confirmed for delivery after the replenishment lead time. In the case of items for which the delivery date falls after the end of the replenishment lead time, the system assumes that everything can be confirmed.
In the standard version, leave this field blank if you want the system to check the replenishment lead time.
Dependencies
If you want the system to check the replenishment lead time, you should make sure that you have entered a value in at least one of the following three fields in the material master:
GR (goods receipt) processing time (Purchasing view)
Planned delivery time (MRP I view)
GR processing time (MRP II view)
Otherwise, the system confirms every requirement
Regards,
nandha

ACE - TCP 60 minute idle timer?

Hi Gilles,
is there a tcp idle timeout with exact 60 minutes within ACE Software for NON LB connections?
I have a certain TCP Connection from a FrontendServer to a certain Backend Server which gets a TCP RST every 60 minutes.
The application guys blame the network for this tcp reset. In my opinion all the timing values which are e.g. set in a connection map are only for the Ports designated within the corresponding loadbalancing rules.
So if i am not wrong any other connection traversing the ACE module should be treated as "simple" connection over any other layer 2/3 switch in a network with the exception that the ace is in charge for the routing of this network.
As i am not hundert percent sure that there isn't a timer comparable to the xlate timeout on PIX or ASA for idle sessions i thought maybe you have an idea.
Have a look at the attached textfile.
Thanks for reading
Roble

Hi,
good information, but i have a doubt.
I have an existing policy L3/L4 multi-match like the one below.
I   would like to increase the inactivity timeout on every TCP connections. Can i nest the new class map (match all) to my policy-map, as shown below in bold?
This can create problems for the existing policy?
Can you confirm me that i can apply only one L3L4 policy map to the interface Vlan?
In necessary to remove and apply the policy to see the effect of the new timeout?
Thanks in advance
Best Regards
policy-map multi-match L4_VIP3_POLICY
description Multi-Match VIPs on Vlan 18 to ServerFarms
class L4-FARM-RDP
    loadbalance vip inservice
    loadbalance policy L7-FARM-RDP
    loadbalance vip icmp-reply active
class L4-FARM-RDP-TOKYO
    loadbalance vip inservice
    loadbalance policy L7-FARM-RDP-TOKYO
    loadbalance vip icmp-reply active
class L4-FARM-RDP-NY
    loadbalance vip inservice
    loadbalance policy L7-FARM-RDP-NY
    loadbalance vip icmp-reply active
class L4-FARM-RDP-KUALA
    loadbalance vip inservice
    loadbalance policy L7-FARM-RDP-KUALA
    loadbalance vip icmp-reply active
class L4-FARM-RDP-NY
    loadbalance vip inservice
    loadbalance policy L7-FARM-RDP-NY
    loadbalance vip icmp-reply active
class TCP-CLASS
     connection advanced TCP-PARAM
where:
parameter-map type connection TCP-PARAM
set timeout inactivity 36000
class-map match-all TCP-CLASS
match port tcp any

SQL Loader Oracle 10g problem in upload date with time data -- Very urgent.

Hi
I am trying to upload data using SQL loader. There are three columns in the table
defined as DATE. When I tried upload a data like this '2007-02-15 15:10:20', it is not loading time part. The date stored as 02/15/2008' only. There is not time on that. I tried with many different format nothing work. Can please help me ?
I have also tried with to_date --> to_timestamp it did not work.
The application is going to be in production, I cannot change DATE to TIME STAMP. This is very urgent.
LASTWRITTEN "decode(:LASTWRITTEN,'null',Null, to_date(:LASTWRITTEN,'YYYY-MM-DD HH24:Mi:SS'))",
CREATEDON "decode(:CREATEDON,'null',Null, to_date(:CREATEDON,'YYYY-MM-DD HH24:Mi:SS'))",
LASTUPDATEDON(21) "decode(:LASTUPDATEDON,'null',Null, to_date(:LASTUPDATEDON(21),'DD/MM/YYYY HH24:MI:SS'))"

Your problem is most likely in decode - the return type in your expression will be character based on first search value ('null'), so it will be implicitly converted to character and then again implicitly converted to date by loading into date column. At some of this conversions you probably are loosing your time part. You can try instead use cast:
SQL> desc t
Name                                      Null?    Type
LASTWRITTEN                                        DATE
CREATEDON                                          DATE
LASTUPDATEDON                                      DATE
SQL> select * from t;
no rows selected
SQL> !cat t.ctl
LOAD DATA
INFILE *
INTO TABLE T
TRUNCATE
FIELDS TERMINATED BY ',' OPTIONALLY ENCLOSED BY '"' TRAILING NULLCOLS
LASTWRITTEN
"decode(:LASTWRITTEN,'null',cast(Null as date),
to_date(:LASTWRITTEN,'YYYY-MM-DD HH24:MI:SS'))",
CREATEDON
"decode(:CREATEDON,'null',cast(Null as date),
to_date(:CREATEDON,'YYYY-MM-DD HH24:MI:SS'))",
LASTUPDATEDON
"decode(:LASTUPDATEDON,'null',cast(Null as date),
to_date(:LASTUPDATEDON,'DD/MM/YYYY HH24:MI:SS'))"
BEGINDATA
2007-02-15 15:10:20,null,null
null,2007-02-15 15:10:20,null
null,null,15/02/2007 15:10:20
SQL> !sqlldr userid=scott/tiger control=t.ctl log=t.log
SQL*Loader: Release 10.2.0.3.0 - Production on Fri Feb 29 00:20:07 2008
Copyright (c) 1982, 2005, Oracle. All rights reserved.
Commit point reached - logical record count 3
SQL> select * from t;
LASTWRITTEN         CREATEDON           LASTUPDATEDON
15.02.2007 15:10:20
                    15.02.2007 15:10:20
                                        15.02.2007 15:10:20Best regards
Maxim

ThinkVantage Power Manager - idle time for screen brightness fixed at 1minute (very anoying)

Dear all,
Please consider this problem:
I have just recieved my new X301 which I am very pleased with. However the ThinkVantage Power Manager has a very annoying bug. When creating a custom power scheme everything works as it should (as far as I can tell) except for one thing. Whilst in the "Idle timers" section the first drop down box which allows you to select the "lower display brightness" time in the "battery settings" column I find that I can select any of the options provided, i.e. "After 1 minute", "After 2 minutes", ...etc "After 45 minutes" or "Never". HOWEVER, regardless of what option I select the power manager instantly reverts back to "After 1 minute" as soon as I exit (selecting the "apply" button or the "okay" button does not help). This is incredibly anoying as it means I'm constantly harrased by the sreen changing brighness when I don't want it to OR having to set the "Lower to" setting to the same as the active screen brightness which means there are no power saving advantages at all and I get the anoying flash of the brightness bars on the screen every 60 seconds (that's 60 times in a working hour!)
I have done the following to try to resolve the problem:
1) updated the power manager to the latest verion: 1.54
2) uninstalled the power manager comletely and then reinstalled it, then applied the updates bit by bit and checking the problem at each stage
3) completely restored the entire system to factory setup (formatting the SSD and losing all data and settings...)
NONE of these options have worked. Please note that this is a brand new system out of the box... (cost 2800USD...)
Can anyone please confirm whether or not this happens on their system as well? Is it just me or is this a global problem? I've called the Lenovo ThinkVantage call centre in the US but they couldn't help.
Thanks for your help,
AMS.

This is clearly a bug in PM 1.54. I get the same thing with my old X40, Win XP, SP3. I've recently installed PM 1.54, and have the same problem. It has nothing to do with scheduled tasks, as (a) I don't have any (and don't run the Task Scheduler service on my machine), and (b) it happens immediately (ie. edits are lost as soon as I try to apply them).
Does anyone know if there is an official place to log bugs for TP software?
[editM also kicks in with the 'idle' timer while I'm working.I like its functions, but PM does seem buggy]
Message Edited by crispinb on 06-16-2009 12:36 PM

Time overlapping of data record..very urgent

Hi All,
while loading time dependent data(texts..0HRPOSITION), i am geeting the following error....
Processing (data packet): Errors occurred
   Data Package 1 ( 7418 Records ) : Errors occurred
          Update ( 0 new / 0 changed ) : Errors occurred
               Data records for package 1 selected in PSA - 2 error(s)
               Record 7415 :0HRPOSITION : Time overlapping of data record 7415 with 7416 : '['20100924'/'20070618'] " .
               Record 7416 :0HRPOSITION : Time overlapping of data record 7415 with 7416 : '['20100924'/'20070618'] ....
Could anyone let me know how to rectify this error and reload the IP..I am workning on production system.....its very urgent
Thanks in advance.
Manjula

Hi Manjula
!)0HRposition infobject and check what is the time previously for that record..
2)Edit the PSA for the 7415 or 7416 and change the vlaue to the previous record time which u found in the infoobject
3) i think ur doing a full load. so better edit the PSA and repload the data from PSA
Regards
AK

Controlling forms 10g idle time with java

Hello,
I'm trying to control web forms 10gr2 idle time with a java bean app, does anyone knows where can i gather some information or examples about this issue.
Please help, it´s very urgent.
Thanks

hi , my dear all
i'm working in the company working in service maintanince and we used oracle in our work
this databse is gerat and most security
i need to learning it , i have mor info about accsess sql and all office work and some info about vb application
need to begining to learn oracle developer and i hop so will'be aprogramer in oracle put i need to help !!!!!!!!
how i can creat aform with oracle 10g
tell me about sql code to learning this version frome oracle
if you need to help me you can conntact me in my mail
1) [email protected]
2) [email protected]
will thank you mor and mor
with best regard
sameh,foda..... cairo..egypt.. 14-dec-2008 11:51:00 pm .... samadon..ashmon..m.n.f
Edited by: user10134747 on 14/12/2008 01:40 م

Finding out idle time

How can i find out the idle time in java?
I want to fire an even if the idle time is 1 minute
Thanks

Topic: IDLE Time for Java Application not SYSTEM Idle Hi I am Krishna , I want to calculate idle time for an application.That is , if user1 uses the application for example called "yahoo site" for checking mails , then after 10 mins he went to outside , from 11th min the status of application should show (Like Yahoo messenger after certail time it shows idle time ) in another ADMINJSP page for Admins that how much this user1 idle say.. : 1 min idle 2 min idle .... .... 10 min idle Now user1 comes and now clicks on application . then ADMINJSP page should show total IDLE time (10 mins idle). And he again after 15 mins he went some where from 16th min the status of the application should show in ADMINJSP page.If user1 left the application like that then the application should be idle for 1 hour i.e 1 min idle 2 min idle ... ... 59 mins idle 60 mins idle Time Up -- Session Expired then he has to login again. So the above is the issue --------------------------------------------------------------------------- What i have done ..................issssssssssssss ------------------------------------------------------------------------- I have taken time for last request by using getLastAccessedTime() I have taken present time System.currentTimeMills() Taking the difference we will get the idle time . But the problem here is When user1 click on any page only this calcuting will be done and showing to ADMINJSP because getLastAccessedTime works only when any requests comes , but we dont want like that , we want the application without any requests from user1 the application should show idle for 1 min , 2 mins , 3 mins...so on upto user1 uses the application then the time should be normal. I have also tried all the EVENTS classes in HttpSessionBinding like valueunbound()...or sessiondestroy() etc. Can any one please help me by giving any CODE.If you need more information plz ask me Plz plz plz plz this is very urgent plz can any please send me the CODE , ihave tried this very hard but no idea how to do? long startTime = session.getLastAccessedTime(); long stopTime = System.currentTimeMillis(); long diffTimeInSecs = (stopTime - startTime) / 1000 ; gives idle time for every request Regards Krishna

How to write code for this logic in a routine, very urgent --help me

hi all,
i want to apply this logic into one subroutin ZABC.
here i m giving my logic ,can any body help me in coding for this, this is very urgent, i hv to submit on wednesday.
4.1 Read the company code number BSEG-BUKRS from document line item.
4.2 Fetch PRDHA from MARA into GV_PRDHA where MATNR = BSEG-MATNR.
4.3 Fetch Business area (GSBER) from ZFIBU into GV_GSBER where (PRDHA = GV_PRDHA and BUKRS = BSEG-BUKRS) OR (PRDHA = GV_PRDHA and BUKRS = SPACE).
4.4 If business area match is found, go to step 3.9. Else continue.
4.5 If BKPF-BLART IN set ZVS_POSDT OR BKPF-XBLNR starts with I0*, execute steps below. Else, go to Step 3.6.
i. MOVE: BSEG-BKURS TO work area field WA_ZFIBUE-BUKRS,
BSEG-MATNR TO work area field WA_ZFIBUE-MATNR,
GV_PRDHA TO work area field WA_ZFIBUE-PRDHA,
BSEG-HKONT TO work area field WA_ZFIBUE-HKONT,
BSEG-GSBER TO work area field WA_ZFIBUE-GSBER,
BSEG-PSWBT TO work area field WA_ZFIBUE-PSWBT,
BKPF-BUDAT TO work area field WA_ZFIBUE-BUDAT,
SY-DATUM TO work area field WA_ZFIBUE-CREDATE,
SY-UZEIT TO work area field WA_ZFIBUE-CRETIME,
Fetch running serial number (WA_ZFIBUE-SERIALNO) from ZFICO. This number will be stored in ZFICO with PARAMTYPE = "BPM030307", SUBTYPE = "ZFIBUE" and KEY1 = "SERIALNO". The actual serial number will be stored in the field VALUE1.
i. Insert WA_ZFIBUE INTO ZFIBUE.
ii. Send email notification to the user (if it is not already sent to user on the same posting date).
Use function module SO_NEW_DOCUMENT_ATT_SEND_API1 to send mail.
Fetch email address and date of last email from ZFICO. These values will be stored in ZFICO with PARAMTYPE = "BPM030307", SUBTYPE = "EMAIL" and KEY1 = "<USERNAME>". The email address will be stored in the field VALUE1 and posting date in VALUE2. Once mail is sent, VALUE2 is updated with latest posting date (BKPF-BUDAT).
iii. Increment the running serial number and update ZFICO with new serial number.
a. GV_ SERIALNO = WA_ZFIBUE-SERIALNO + 1
b. Update ZFICO Set value1 = GV_SERIALNO
Where PARAMTYPE = "BPM030307" AND
SUBTYPE = "ZFIBUE" AND
KEY1 = "SERIALNO".
iv Move VDFT to BSEG-GSBER.
v. Exit routine.
4.6 Fetch MTART into GV_MTART from MARA where MATNR = BSEG-MATNR.
4.7 If SY-BATCH = INITIAL AND GV_MTART <> ROH, issue the error message - Maintain the mapping of product hierarchy <PRDHA> from article <MATNR> for <BUKRS>. Else, go to step 3.8.
4.8 If SY-BATCH <> INITIAL AND GV_MTART <> ROH, issue the error message - Maintain product hierarchy on article master. Go to step 3.10.
4.9 Move GV_GSBER TO BSEG-GSBER.
4.10 Exit Routine
plz give me reply asap --this is very urgent
thanks in advance
swathi

Hi Swathi,
If it's very very urgent then you better get on with it, don't waste time on the web. Chop chop.

How to write code for this logic, plz help me very urgent

Hi All,
i am new to sap-abap, i got this work and i m working on this can any body help me in writing code, plz help me, this is very very urgent.
here i m giving my logic, can anybody send me the code related to this logic.
this is very urgent .
this program o/p should be in ALV format and need to create one commond 'SAVE" on this o/t list if user clicks save processedon and processedby fields in ZFIBUE should be updated automatically.
i am creating one custom table zfibue having fields: (serialno, bukrs, matnr,prdha,hkont,gsber,wrbtr,budat, credate, cretime,processed, processedon, processedby,mapped)
fields of zfibue:
serailno = numc
bukrs = char
matnr = char
prdha = char
hkont = char
gsber = char
wrbtr = char
budat = date
credate = date
cretime = time
processed= char
processedon = date
processedby = char
mapped = char      are   belongs to above type data types
and seelct-optionfields: s_bukrs for bseg-bukrs
                                    s_hkont for bseg-hkont,
                                     s_budat for bkpf-budat,
                                     s_processed for zfibue-processed,
                                      s_processedon for zfibue-processedon,
                                      s_mapped. for zfibue-mapped
parameters: p_chk1 as checkbox,
                  p_chk2 as checkbox.
                  p_filepath type rlgrap-filename.
1.1 Validate the user inputs (S_BUKRS and S_HKONT) against respective check tables (T001 and SKB1). If the validation fails, provide respective error message. Eg: Invalid input for Company Code.
1.2 Fetch SERIALNO, BUKRS, MATNR, PRDHA, HKONT, GSBER, WRBTR, BUDAT, CREDATE, CRETIME, PROCESSED, PROCESSEDON, PROCESSEDBY, MAPPED from table ZFIBUE into internal table GT_ZFIBUE where BUKRS IN S_BUKRS, HKONT IN S_HKONT, BUDAT IN S_BUDAT, PROCESSED IN S_PROCESSED, PROCESSEDON IN S_PROCESSEDON, and MAPPED IN S_MAPPED.
1.3 If P_CHK2 = X, go to step 1.11. Else continue.
1.4 If P_CHK1 = X, continue. Else go to step 1.9
1.5 Fetch MATNR, PRDHA from MARA into GT_MARA for all entries in GT_ZFIBUE where MATNR = GT_ZFIBUE-MATNR.
1.6 Sort and delete adjacent duplicates from GT_MARA based on MATNR.
1.7 Loop through GT_ZFIBUE where PRDHA = blank.
          Read Table GT_MARA based on MATNR = GT_ZFIBUE-MATNR.
          IF sy-subrc = 0.
                 Move GT_MARA-PRDHA to GT_ZFIBUE-PRDHA.
              Modify Table GT_ZFIBUE. Update Product Hierarchy
             Endif.
    Fetch PRDHA, GSBER from ZFIBU into GT_ZFIBU for all entries in GT_ZFIBUE where PRDHA = GT_ZFIBUE-PRDHA.
    Read Table GT_ZFIBU based on PRDHA = GT_ZFIBUE-PRDHA.
          IF sy-subrc = 0.
                 Move GT_ZFIBU-GSBER to GT_ZFIBUE-GSBER.
              Move X to GT_ZFIBUE-MAPPED.
              Modify Table GT_ZFIBUE.
             Endif.
Endloop.
1.8 Modify database table ZFIBUE from GT_ZFIBUE.
1.9 Fill the field catalog table GT_FIELDCAT using the details of output fields listed in section Inputs/Outputs (above).
   Eg:                 LWA_ FIELDCAT -SELTEXT_L = 'Serial Number.
                          LWA_ FIELDCAT -DATATYPE = NUMC.
                          LWA_ FIELDCAT -OUTPUTLEN = 9.
                          LWA_ FIELDCAT -TABNAME = 'GT_ZFIBUE'.
                          LWA_ FIELDCAT-FIELDNAME = 'SERIALNO'.
          Append LWA_FIELDCAT to GT_FIELDCAT
Note: a) The output field GT_ZFIBUE-PROCESSED will be editable marking INPUT = X in field catalog (GT_FIELDCAT).
         b) The standard ALV functionality will be used to give the user option for selecting all or blocks of entries at a time.
         c) The PF-STATUS STANDARD_FULLSCREEN from function group SLVC_FULLSCREEN will be copied to the program and modified to include a SAVE button.
1.10 Call the function module REUSE_ALV_GRID_DISPLAY passing output table GT_ZFIBUE and field catalog GT_FIELDCAT. Additional parameters like I_CALLBACK_PF_STATUS_SET (= ZFIBUESTAT) and I_CALLBACK_USER_COMMAND (=HANDLE_USER_ACTION) will also be passed to handle user events. Go to 2.14.
1.11 Download the file to P_FILEPATH using function module GUI_DOWNLOAD passing GT_ZFIBUE.
1.12 Exit Program.
Logic to be implemented in routine Handle_User_Action
This routine will have the following interface:
FORM Handle_User_Action USING r_ucomm LIKE sy-ucomm
                                                           rs_selfield TYPE slis_selfield.
ENDFORM.
Following logic will be implemented in this routine:
1.     If r_ucomm = SAVE, continue. Else exit.
2.     Loop through GT_ZFIBUE where SEL_ROW = X. Row is selected
a.     IF GT_ZFIBUE-PROCESSED = X.
i.     GT_ZFIBUE-PROCESSEDON = SY-DATUM.
ii.     GT_ZFIBUE-PROCESSEDBY = SY-UNAME.
iii.     MODIFY ZFIBUE FROM work area GT_ZFIBUE.
Endif.
Endloop.

Hi Swathi,
If it's very very urgent then you better get on with it, don't waste time on the web. Chop chop.

Please help me with the following two questions, very urgent

Hi All,
Please help me with some scenerios about what are the common problems when modifying a standard script such a standard Invoice script and how can we overcome them.
What are the common problems encountered when working with SAP SMARTFORMS and how to overcome them?
Please help me with these questions, its very urgent.
Thanks in advance.
MD.

hi
hope it will help you.
reward if ehlp.
How to create a New smartfrom, it is having step by step procedure
http://sap.niraj.tripod.com/id67.html
step by step good ex link is....
http://smoschid.tripod.com/How_to_do_things_in_SAP/How_To_Build_SMARTFORMS/How_To_Build_SMARTFORMS.html
Here is the procedure
1. Create a new smartforms
Transaction code SMARTFORMS
Create new smartforms call ZSMART
2. Define looping process for internal table
Pages and windows
First Page -> Header Window (Cursor at First Page then click Edit -> Node -> Create)
Here, you can specify your title and page numbering
&SFSY-PAGE& (Page 1) of &SFSY-FORMPAGES(Z4.0)& (Total Page)
Main windows -> TABLE -> DATA
In the Loop section, tick Internal table and fill in
ITAB1 (table in ABAP SMARTFORM calling function) INTO ITAB2
3. Define table in smartforms
Global settings :
Form interface
Variable name Type assignment Reference type
ITAB1 TYPE Table Structure
Global definitions
Variable name Type assignment Reference type
ITAB2 TYPE Table Structure
4. To display the data in the form
Make used of the Table Painter and declare the Line Type in Tabstrips Table
e.g. HD_GEN for printing header details,
IT_GEN for printing data details.
You have to specify the Line Type in your Text elements in the Tabstrips Output options.
Tick the New Line and specify the Line Type for outputting the data.
Declare your output fields in Text elements
Tabstrips - Output Options
For different fonts use this Style : IDWTCERTSTYLE
For Quantity or Amout you can used this variable &GS_ITAB-AMOUNT(12.2)&
5. Calling SMARTFORMS from your ABAP program
REPORT ZSMARTFORM.
Calling SMARTFORMS from your ABAP program.
Collecting all the table data in your program, and pass once to SMARTFORMS
SMARTFORMS
Declare your table type in :-
Global Settings -> Form Interface
Global Definintions -> Global Data
Main Window -> Table -> DATA
Written by : SAP Hints and Tips on Configuration and ABAP/4 Programming
http://sapr3.tripod.com
TABLES: MKPF.
DATA: FM_NAME TYPE RS38L_FNAM.
DATA: BEGIN OF INT_MKPF OCCURS 0.
INCLUDE STRUCTURE MKPF.
DATA: END OF INT_MKPF.
SELECT-OPTIONS S_MBLNR FOR MKPF-MBLNR MEMORY ID 001.
SELECT * FROM MKPF WHERE MBLNR IN S_MBLNR.
MOVE-CORRESPONDING MKPF TO INT_MKPF.
APPEND INT_MKPF.
ENDSELECT.
At the end of your program.
Passing data to SMARTFORMS
call function 'SSF_FUNCTION_MODULE_NAME'
exporting
formname = 'ZSMARTFORM'
VARIANT = ' '
DIRECT_CALL = ' '
IMPORTING
FM_NAME = FM_NAME
EXCEPTIONS
NO_FORM = 1
NO_FUNCTION_MODULE = 2
OTHERS = 3.
if sy-subrc <> 0.
WRITE: / 'ERROR 1'.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
endif.
call function FM_NAME
EXPORTING
ARCHIVE_INDEX =
ARCHIVE_INDEX_TAB =
ARCHIVE_PARAMETERS =
CONTROL_PARAMETERS =
MAIL_APPL_OBJ =
MAIL_RECIPIENT =
MAIL_SENDER =
OUTPUT_OPTIONS =
USER_SETTINGS = 'X'
IMPORTING
DOCUMENT_OUTPUT_INFO =
JOB_OUTPUT_INFO =
JOB_OUTPUT_OPTIONS =
TABLES
GS_MKPF = INT_MKPF
EXCEPTIONS
FORMATTING_ERROR = 1
INTERNAL_ERROR = 2
SEND_ERROR = 3
USER_CANCELED = 4
OTHERS = 5.
if sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
endif.
Smartform
you can check this link here you can see the steps and you can do it the same by looking at it..
http://smoschid.tripod.com/How_to_do_things_in_SAP/How_To_Build_SMARTFORMS/How_To_Build_SMARTFORMS.html
SMARTFORMS STEPS.
1. In Tcode se11 Create a structure(struct) same like the Internal table that you are going to use in your report.
2. Create Table type(t_struct) of stracture in se11.
3. In your program declare Internal table(Itab) type table of structure(struct).
4. Define work area(wa) like line of internal table.
5. Open Tcode Smartforms
6. In form Global setting , forminterface Import parameter define Internal table(Itab) like table type of stracture(t_struct).
7. In form Global setting , Global definitions , in Global data define Work area(wa) like type stracture(struct).
8. In form pages and window, create Page node by default Page1 is available.
9. In page node you can create numbers of secondary window. But in form there is only one Main window.
10. By right click on page you can create windows or Go to Edit, Node, Create.
11. After creating the window right click on window create table for displaying the data that you are passing through internal table.
12. In the table Data parameter, loop internal internal table (Itab) into work area(wa).
13. In table there are three areas Header, Main Area, Footer.
14. Right click on the Main area create table line by default line type1 is there select it.
15. Divide line into cells according to your need then for each cell create Text node.
16. In text node general attribute. Write down fields of your work area(wa) or write any thing you want to display.
17. Save form and activate it.
18. Then go to Environment, function module name, there you get the name of function module copy it.
19. In your program call the function module that you have copied from your form.
20. In your program in exporting parameter of function pass the internal table(itab).
SAP Smart Forms is introduced in SAP Basis Release 4.6C as the tool for creating and maintaining forms.
SAP Smart Forms allow you to execute simple modifications to the form and in the form logic by using simple graphical tools; in 90% of all cases, this won't include any programming effort. Thus, a power user without any programming knowledge can
configure forms with data from an SAP System for the relevant business processes.
To print a form, you need a program for data retrieval and a Smart Form that contains the entire from logic. As data retrieval and form logic are separated, you must only adapt the Smart Form if changes to the form logic are necessary. The application program passes the data via a function module interface to the Smart Form. When activating the Smart Form, the system automatically generates a function module. At runtime, the system processes this function module.
You can insert static and dynamic tables. This includes line feeds in individual table cells, triggering events for table headings and subtotals, and sorting data before output.
You can check individual nodes as well as the entire form and find any existing errors in the tree structure. The data flow analysis checks whether all fields (variables) have a defined value at the moment they are displayed.
SAP Smart Forms allow you to include graphics, which you can display either as part of the form or as background graphics. You use background graphics to copy the layout of an existing (scanned) form or to lend forms a company-specific look. During printout, you can suppress the background graphic, if desired.
SAP Smart Forms also support postage optimizing.
Also read SAP Note No. 168368 - Smart Forms: New form tool in Release 4.6C
What Transaction to start SAP Smart Forms?
Execute transaction SMARTFORMS to start SAP Smart Forms.
Key Benefits of SAP Smart Forms:
SAP Smart Forms allows you to reduce considerably the implementation costs of mySAP.com solutions since forms can be adjusted in minimum time.
You design a form using the graphical Form Painter and the graphical Table Painter. The form logic is represented by a hierarchy structure (tree structure) that consists of individual nodes, such as nodes for global settings, nodes for texts, nodes for output tables, or nodes for graphics.
To make changes, use Drag & Drop, Copy & Paste, and select different attributes.
These actions do not include writing of coding lines or using a Script language.
Using your form description maintained in the Form Builder, Smart Forms generates a function module that encapsulates layout, content and form logic. So you do not need a group of function modules to print a form, but only one.
For Web publishing, the system provides a generated XML output of the processed form.
Smart Forms provides a data stream called XML for Smart Forms (XSF) to allow the use of 3rd party printing tools. XSF passes form content from R/3 to an external product without passing any layout information about the Smart Form.
SmartForms System Fields
Within a form you can use the field string SFSY with its system fields. During form processing the system replaces these fields with the corresponding values. The field values come from the SAP System or are results of the processing.
System fields of Smart Forms
&SFSY-DATE&
Displays the date. You determine the display format in the user master record.
&SFSY-TIME&
Displays the time of day in the form HH:MM:SS.
&SFSY-PAGE&
Inserts the number of the current print page into the text. You determine the format of the page number (for example, Arabic, numeric) in the page node.
&SFSY-FORMPAGES&
Displays the total number of pages for the currently processed form. This allows you to include texts such as'Page x of y' into your output.
&SFSY-JOBPAGES&
Contains the total page number of all forms in the currently processed print request.
&SFSY-WINDOWNAME&
Contains the name of the current window (string in the Window field)
&SFSY-PAGENAME&
Contains the name of the current page (string in the Page field)
&SFSY-PAGEBREAK&
Is set to 'X' after a page break (either automatic [Page 7] or command-controlled [Page 46])
&SFSY-MAINEND&
Is set as soon as processing of the main window on the current page ends
&SFSY-EXCEPTION&
Contains the name of the raised exception. You must trigger your own exceptions, which you defined in the form interface, using the user_exception macro (syntax: user_exception <exception name >).
Example Forms Available in Standard SAP R/3
SF_EXAMPLE_01
Simple example; invoice with table output of flight booking for one customer
SF_EXAMPLE_02
Similar to SF_EXAMPLE_01 but with subtotals
SF_EXAMPLE_03
Similar to SF_EXAMPLE_02, whereby several customers are selected in the application program; the form is called for each customer and all form outputs are included in an output request
Advantages of SAP Smart Forms
SAP Smart Forms have the following advantages:
1. The adaption of forms is supported to a large extent by graphic tools for layout and logic, so that no programming knowledge is necessary (at least 90% of all adjustments). Therefore, power user forms can also make configurations for your business processes with data from an SAP system. Consultants are only required in special cases.
2. Displaying table structures (dynamic framing of texts)
3. Output of background graphics, for form design in particular the use of templates which were scanned.
4. Colored output of texts
5. User-friendly and integrated Form Painter for the graphical design of forms
6. Graphical Table Painter for drawing tables
7. Reusing Font and paragraph formats in forms (Smart Styles)
8. Data interface in XML format (XML for Smart Forms, in short XSF)
9. Form translation is supported by standard translation tools
10. Flexible reuse of text modules
11. HTML output of forms (Basis release 6.10)
12. Interactive Web forms with input fields, pushbuttons, radio buttons, etc. (Basis-Release 6.10)

HT202786 my friend shared a video with me on icloud photo sharing and then she deleted it from her camera roll, how do I save it???(very urgent)

my friend shared a video with me on icloud photo sharing and then she deleted it from her camera roll, how do I save it???(very urgent)

DVDs are encoded into MPEG2, which iMovie cannot edit. So you need to convert the DVD back to something else. For highest quality, I recommend that you convert the DVD to Apple Intermediate Codec. There is a free tool called MPEG Streamclip that will do this. You will also need to install the Apple QuickTIme MPEG2 Playback Component.
Here are the details.
1) Download and install the Apple MPEG2 QuickTime Component ($20) - available online from Apple.
2) Download and install MPEG Streamclip from Squared 5 (free).
3) Start MPEG Streamclip
4) Insert your DVD into your Mac. If DVD Player or Front Row starts automatically quit those.
5) Open a Finder window. Navigate to your DVD to the Video_TS folder.
6) Drag the .VOB files from the Video_TS folder and drop then into MPEG Streamclip.
7) If MPEG Streamclip offers to fix timecode breaks, say yes.
8) Use FILE/EXPORT TO QUICKTIME to convert the files to Apple Intermediate Codec (or h.264 if you prefer)
9a) Optional: You can deinterlace your footage in this step, if you like
9b) optional: If you know the date and or time of the footage, name your file
clip-yyyy-mm-dd hh;mm;ss
(let mpeg streamclip provide the extension). This will provide metadata that iMovie will use to put the event in the right year and month.
9c) Optional: If you don't want to make one huge clip out of your DVD, you can make smaller clips by using MPEG Streamclip. Move the cursor to the "in" point of the clip, and press i. Move the cursor to the "Out" point of the clip, and press o. Then do steps 8 through 10 and repeat until you have done this for all clips you want.
10) Save the resulting file in a place where you can find it, like your Desktop.
11) Open iMovie.
12) In iMovie, choose FILE/IMPORT/From File and choose the file you saved in steps 8, 9, 10.
13) iMovie will generate thumbnails and you can edit.

SQL SELECT Query Help ..Please its very Urgent!!

Hi All,
I am having Oracle Database whice is storing 1000's of records daily.
I need to select some information based on date and time.
I am having two coloumns for Date and time. The first column(testDate) of type Date stores date as MM/DD/YY format and the second column(testTime)of type Numeric stores the time in seconds.
The Example data is :
testDate ------=-- testTime
11/12/2002 --- 35000
11/12/2002 --- 43000
11/12/2002 --- 45000
11/12/2002 --- 75000
11/13/2002 --- 2000
11/13/2002 --- 3500
11/13/2002 --- 4300
11/13/2002 --- 9800
11/13/2002 --- 23000
11/14/2002 --- 5000
11/14/2002 --- 10000
11/14/2002 --- 15000
How can i write a SELECT Query to get the records of specific date and seconds to next day specific date and seconds.I mean i want all the records between 11/12/2002 --- 43000 seconds to 11/14/2002 --- 1000 seconds.
If any one helps me in this regard iam very thank full to them.Its very urgent for me.
Thanks

Hi m7nra,
I used the query as
SELECT * FROM table
WHERE testDate + (testTime/(24*60*60)) BETWEEN TO_DATE('MM/DD/YYYY','12.11.2002') AND TO_DATE('MM/DD/YYYY','14.11.2002')
its giving DATE FORMAT NOT RECOGNIZED error.
The Example data is :
testDate ------=-- testTime
11/12/2002 --- 35000
11/12/2002 --- 43000
11/12/2002 --- 45000
11/12/2002 --- 75000
11/13/2002 --- 2000
11/13/2002 --- 3500
11/13/2002 --- 4300
11/13/2002 --- 9800
11/13/2002 --- 23000
11/14/2002 --- 5000
11/14/2002 --- 10000
11/14/2002 --- 15000
infact i need all the records between 11/12/2002 --- 43000 seconds to 11/14/2002 --- 1000 seconds.
Please help me to find a full query beacuse iam very new to Oracle.
Thanks,
S R Mannava

Very urgent --pls help Report Painter Problem,

Hi to all,
I have created 5 operating expenses report by cost centres through report painter. some for full period , some for actual and sone for budget.
Under one set of that cost centre reports I have many subsets under which there are cost centre groups and then the cost centres.
I want to add one more set to existing set. I have added the set and set contains one cost centre group and their are also cost centres under it.
The table which i am using for cost centre grous is GLT1 and field is RCNTR and for cost centres it is CCSS and KOSTL respectively.
In the above procedure I have two queries.
1)even after adding the set and when i try to execute the report from T- code SERP it doesnot show my created set in variation.
2)Also even if it was showing the set earlier but report was showing zero values. When i clicked on zero amount a pop up arises for plan and actual values and when i clicked on plan values it had value of Rs 255000(for cost centres). then outside why this amount doesnot appears.
PLS THIS IS VERY VERY URGENT
Regards
TANUJA

I've just read this thread three times and I have absolutely no idea what you are doing, in what version, and what you are asking for help with.
Do you want to change the message type? If you do you MUST drop the queue and start over again from the beginning.
Do you want to enqueue messages?
Post your DDL and other relevant information or you are on your own. We can not guess at your issue.

Ace tcp idle timer VERY URGENT!

Similar Messages

Maybe you are looking for