Acer aspire 5670: Performance issues

I have now kdemod installed, but this has been happening on kde and gnome, so i think it is because of the damn ati video card.
The point is that the system gets completely frozen for some minutes, and then all goes back to normal during some seconds again......
Could it be some issues with the video driver? WHat can i try? Of course, composition is deactivated.
If you reboot the system it seems to be ok for the first minutes, then you can see how the memory usage and the processor usage increases constantly, even when you are doing nothing.....
Any suggestions would be apreciated.
Thanks!!!

What video driver do you use, open or proprietary? Do you run with or without xorg.conf? If you use xorg.conf, it could help to post it. Do you use KMS (kernel mode setting). Personally, I had problems with an ATI card and KMS, so I disabled it and my problems went away. See wiki article on how to disable it:
http://wiki.archlinux.org/index.php/ATI … _.28KMS.29
On the other hand, some people report performance improvements using KMS, so you may want to set it up according to the wiki article and see if it helps.
Did you look into, e.g. htop, during times of high CPU usage?

Similar Messages

[SOLVED] Card reader in Acer Aspire 5670

I have an Acer Aspire 5670 Laptop in which the card reader was working under ubuntu (as far as i can remember), but i cannot get it to work under arch.
iAs the wiki pages does not have any article related to this model, and trying with symilar model wikis is not getting me anywhere, i need your help, at least to tell me where to start from.
Thanks!!
Last edited by Xi0N (2009-02-10 00:27:59)

I have this messages:
tifm_core: MMC/SD card detected in socket 0:1
mmc0: new SD card at address 0002
mmcblk0: mmc0:0002 3.67 GiB
mmcblk0:
mmcblk0: error -110 transferring data
end_request: I/O error, dev mmcblk0, sector 7700352
Buffer I/O error on device mmcblk0, logical block 962544
This is what i get. The card is not formatted, but i use gparted for viewing graphically the devices buut this card (4Gb) does not show up...
Please, a bit more help.. i think we are close!!!

Acer Aspire 7750g driver issue.

Hello everyone,
I own an Acer Aspire 7750g-2636G75Mnkk
Recently i updated to Windows 10 but i found out that my AMD Radeon 6650M is not supported, so i switched back to windows 7 with the Back up disc i made with the factory settings.
So i tried to update everything, i used the AMD auto detect tool and it did install to the newest 15.7 driver. After the restart i got horizontal black lines flickering over my screen so i uninstalled it and went back to the factory driver.
Went to the acer site for driver download and i saw there was a "newer" version available. (8.901.4.0).
So i uninstalled the factory one(8.822.0.0) and installed this one. But the installer said when it was done that there were some problems. I checked the log but everything was succesfully installed.
After the restart everything went good until after the login screen. Screen was black with green, i could barely see anything.
Tried to plug HDMI cable into my TV.
Tv screen is normal but laptop screen is still black and green.
So i uninstalled that one again and went back with the factory one. (8.822.0.0)
I am now running into compatibility issues, i can start a program but it closes right after. I can only start it when i put Windows 7 manually in the compatibility mode.
Even some games say my drivers are outdated.
When i do 64bit DxDiag, it says program stopped working. Started it again and it said it had problems accessing the Direct3D. If i don't skip this step, it stops working. But if i do skip it, it runs but when i check the Screen tab, there is nothing. Not even a driver detected.
I can't even open Catalyst Control Center because it says program stopped working and has been shutdown.
I have updated my BIOS to the latest version Acer gave me V1.21
Oh, and i also downloaded all the updates from Windows Update.
I tried different kind of Catalyst Control Center Suites(mostly the same as the newest driver 15.7, horizontal black lines flickering over the whole screen)
So now im stuck.
Someone got an idea on how to fix this?

Hello Guys, Even I had a similar problem. I was planning to take it to service center. But just wanted to try once more so searched in the community and got this thread.My situation is I changed my RAM 2 months ago from 3GB to 8GB on my 5830TG. It was working fine till last couple of weeks until I made one change in BIOS setting and then I tried rebooting then I don't get any screen. my Hardisk looks like it was running. I never got to BIOS screen at all. I got scared & din't know what to do. After reading this post I replaced my new ram with the old once which I had it with me. My laptop booted properly. Then I removed the old ones & added both the new RAM's then the laptop did not boot. Suspecting that one of the RAM must have gone non functional I tried one by one. Both worked fine. Finally I had to insert the RAM properly. Insert it little hard so that it sat fine in the slot. I also reset my BIOS just in case. Great post guys, it helped my try once. You don't know how much time and money I saved :-) Thanks a ton.

[Fixed]Acer Aspire 7750g driver issue.

Hello everyone,
I own an Acer Aspire 7750g-2636G75Mnkk
Recently i updated to Windows 10 but i found out that my AMD Radeon 6650M is not supported, so i switched back to windows 7 with the Back up disc i made with the factory settings.
So i tried to update everything, i used the AMD auto detect tool and it did install to the newest 15.7 driver. After the restart i got horizontal black lines flickering over my screen so i uninstalled it and went back to the factory driver.
Went to the acer site for driver download and i saw there was a "newer" version available. (8.901.4.0).
So i uninstalled the factory one(8.822.0.0) and installed this one. But the installer said when it was done that there were some problems. I checked the log but everything was succesfully installed.
After the restart everything went good until after the login screen. Screen was black with green, i could barely see anything.
Tried to plug HDMI cable into my TV.
Tv screen is normal but laptop screen is still black and green.
So i uninstalled that one again and went back with the factory one. (8.822.0.0)
I am now running into compatibility issues, i can start a program but it closes right after. I can only start it when i put Windows 7 manually in the compatibility mode.
Even some games say my drivers are outdated.
When i do 64bit DxDiag, it says program stopped working. Started it again and it said it had problems accessing the Direct3D. If i don't skip this step, it stops working. But if i do skip it, it runs but when i check the Screen tab, there is nothing. Not even a driver detected.
I can't even open Catalyst Control Center because it says program stopped working and has been shutdown.
I have updated my BIOS to the latest version Acer gave me V1.21
Oh, and i also downloaded all the updates from Windows Update.
I tried different kind of Catalyst Control Center Suites(mostly the same as the newest driver 15.7, horizontal black lines flickering over the whole screen)
So now im stuck.
Someone got an idea on how to fix this?
Edit: After a long search on how to fix it, i've finally found it.
I have downloaded Display Driver Uninstaller from Guru3d.
Cleaned everything in safe mode and reinstalled the driver.
Everything works perfect now!

Hello, Aspire 7750g (7750 series and 7560 series):55.RB002.001POWER BD Aspire 5750:55.RFD02.001POWER BD They are not compatible.

Acer aspire ES1-111 issues

Hi all,I decided to register in this community in order to get some advice and opinion about issues I'm experiencing with this laptop. I'm an owner of an Acer Aspire ES1-111 which I bought a week ago. Since its first configuration I noticed problems using it with windows 8.1 (its native OS). For example touchpad or keyboard not working properly and, most of all, shutdown problems. In this particular case I was never able to shutdown properly the device, because it either freezed or remained with the power indicator that continued being "on" although it seemed that the system was shutdown. However, in order to really shutdown I had to press power button. Firstly I decided to reset the system with the integrated software eRecovery but problems remained. Secondly I decided to do a clean install of the operating system and I tried both Windows 8 and Windows 8.1. In both cases, installation process finished without problems but when trying installing all drivers I experienced freezes and again shutdown problems. I followed an order to install drivers (Chipset first, than VGA etc), but in most of cases I had the aformentioned issues. I also tried disabling "Turn on fast startup (recommended)" to no avail. But now comes the strange part... I finally decided to give a try to Windows 7 and, to my surprise, everything is working fine! I was able to install drivers properly and to shutdown or restart my notebook without problems. Now I'm using it with Windows 7, but, as it is in warranty, I would like to ask you what do you think about this issues. I find quite strange that a notebook isn't working properly with its native OS but it's fine with an old OS!! Do you think I should send it to Acer assistance or ask to change it (although, I don't know if I'm still able to pursue this second option). Thanks for your attention! Mic

Bios was set to UEFI when I bought the notebook. System was very slow on its first configuration, probably due to all the third part softwares installed. Also the hdd was not partitioned, something I didn't like. So, after a reset with Acer eRecovery software that didn't solved the slowness of the system, I decided for a clean install with a Windows 8.1 bootable usb stick I had. And, in order to select the boot order desired, I had to change bios mode from UEFI to LEGACY. But, I think that this step was not the best option for a notebook that has a native UEFI bios, as my struggles showed. So, after some research, I decided to reset bios to UEFI, create a usb bootable stick that was compatible with UEFI (through RUFUS software) and run again installation process of Windows 8.1. And this time, all steps were done automatically and without problems. System is far more usable now. Yes, I lost the eRecovery partition, but I can alwasys use the one that the new installation has created.

ACER ASPIRE 5560G BIOS ISSUE

I purchased a Acer Aspire 5560g yesterday second hand , lappy worked great. Was updating all the drivers one of which was the BIOS. The install went through and then upon reboot the machine Black Screened. No HDD activity no display. Just a solid Blue light on front bezel fan running. Connected to external monitor and still nothing. From all Ive read it sounds like the BIOS installed hosed. Can someone PLEASE give me a good step by step on how to reflash the BIOS on this machine using a USB drive? I have also reset the cmos battery and reseated the ram.

Hello Guys, Even I had a similar problem. I was planning to take it to service center. But just wanted to try once more so searched in the community and got this thread.My situation is I changed my RAM 2 months ago from 3GB to 8GB on my 5830TG. It was working fine till last couple of weeks until I made one change in BIOS setting and then I tried rebooting then I don't get any screen. my Hardisk looks like it was running. I never got to BIOS screen at all. I got scared & din't know what to do. After reading this post I replaced my new ram with the old once which I had it with me. My laptop booted properly. Then I removed the old ones & added both the new RAM's then the laptop did not boot. Suspecting that one of the RAM must have gone non functional I tried one by one. Both worked fine. Finally I had to insert the RAM properly. Insert it little hard so that it sat fine in the slot. I also reset my BIOS just in case. Great post guys, it helped my try once. You don't know how much time and money I saved :-) Thanks a ton.

[SOLVED] Acer Aspire One - Wireless issue + Wpa_supplicant

Hi there!
I've been using arch on both my desktop and laptop for a while, with wpa_supplicant working perfectly for both of them (University 802.1x auth) I have a config file which works perfectly on the same wireless network with my laptop, but on the netbook I just can't seem to get on it. It's an Acer Aspire One - A150.
This computer uses as we know an atheros chip, which I just can't seem to get working. My laptop on the other hand uses an ipw2200 chip which works fine.
I've installed the madwifi modules, and when doing iwconfig i can see wlan0 listed. If i try to scan for wireless ap's with "iwlist wlan0 scan" it does not find anything.
Doing "wpa_supplicant -Dmadwifi -iwlan0 -c/..../wpa_supplicant.conf -dd " produces the following error
[henrik@scribble ~]$ sudo wpa_supplicant -Dmadwifi -iwlan0 -c/home/henrik/wpa_supplicant.conf -dd
Initializing interface 'wlan0' conf '/home/henrik/wpa_supplicant.conf' driver 'madwifi' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/home/henrik/wpa_supplicant.conf' -> '/home/henrik/wpa_supplicant.conf'
Reading configuration file '/home/henrik/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
eapol_version=1
ap_scan=1
fast_reauth=1
Line: 485 - start of a new network block
ssid - hexdump_ascii(len=7):
65 64 75 72 6f 61 6d eduroam
key_mgmt: 0x1
eap methods - hexdump(len=16): 00 00 00 00 19 00 00 00 00 00 00 00 00 00 00 00
identity - hexdump_ascii(len=21):
68 72 69 30 30 33 40 6d 61 69 6c 62 6f 78 2e 75 xXxXXX@xxxxxxx
69 74 2e 6e 6f xx.com
password - hexdump_ascii(len=8): [REMOVED]
phase2 - hexdump_ascii(len=13):
61 75 74 68 3d 4d 53 43 48 41 50 56 32 auth=MSCHAPV2
priority=10 (0xa)
Priority group 10
id=0 ssid='eduroam'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
ioctl[IEEE80211_IOCTL_SETPARAM]: Operation not supported
wpa_driver_madwifi_init: failed to set wpa_supplicant-based roaming
WEXT: Operstate: linkmode=0, operstate=6
Failed to initialize driver interface
Failed to add interface wlan0
Cancelling scan request
Cancelling authentication timeout
[henrik@scribble ~]$
I really hope some of you have a suggestion to what I can do to fix this, as it's really annoying only being able to use wired.
What I find wierd, is that "iwlist...scan" does not work.
Thanks in advance
-Henrik
Last edited by henrikken (2009-03-24 15:49:54)

two things:
1. Your computer should be using the ath5k driver for the ar5007 chipset that your netbook has... and
2. If the opensource approach doesn't work for you, build this driver.
p.s. (wlan0 will be renamed to ath0)
#Contributor: KJoN <[email protected]>
pkgname=madwifi-hal
pkgver=0.10.5.6
pkgrel=svn
pkgdesc="Multiband Atheros Drivers - hal 0.10.5.6 - svn"
arch=('i686' 'x86_64')
url="http://svn.madwifi-project.org"
license=('GPL')
depends=('subversion')
provides=('madwifi' 'madwifi-utils')
source=()
md5sums=()
build() {
cd $startdir/src
svn co http://svn.madwifi-project.org/madwifi/branches/$pkgname-$pkgver
cd $pkgname-$pkgver
make
make DESTDIR=$startdir/pkg install
cp $startdir/pkg/usr/local/* $startdir/pkg/usr -vR
cp $startdir/pkg/usr/share/* $startdir/pkg/usr -vR
rm $startdir/pkg/usr/{local,share} -r
errr... remember to blacklist ath5k on MODULES on your rc.conf and please, run depmod -a after installing this package.
Luck with your issue

[fixed] Touchpad suddenly not working on Acer Aspire 5670

I am using gnome 2.28 and i never had any problem with my touchpad: I actually cannot recall having updated before this issue came out..... just, suddenly, the touchpad is not working... no movement, no clicking... nothing at all.....
I am using an external useb mouse........ i am also using hotplugging (no xorg.conf).... any idea? Not having mouse is quite frustrating
Last edited by Xi0N (2009-10-29 12:40:11)

that's odd..
does the touchpad works on login screen?
(mine did it there, but no in the desktop)
is it enabled in Bios option?
did you try erasing and re-installing xf86-input-synaptics?
pacman -Rsn xf86-input-synaptics, and then pacman -S xf86-input-synaptics
just giving you ideas.. 'cause i don't know what can be the cause
ps: did you read this wiki? http://wiki.archlinux.org/index.php/Touchpad_Synaptics
Last edited by palinux (2009-10-24 03:21:40)

Screen turns bluish on shutdown Asus ee pc running through an Aspire 5670 monitor

I know this is a bit of an odd one but I hope that maybe someone can help me!
I'm running photoshop on my Asus eee pc but I have it running on an Acer Aspire 5670 monitor (bigger screen makes it easier for my retouching work!) and whenever I shutdown photoshop my screen gets a little bit bluer.
I can fix it by doing a recalibration but it's still kinda annoying because I don't always remember to do it and I'm sure you can understand that trying to get skin tones right when your screen is blue can be an utter nightmare.
Please let me know what other information you might need to help.
Thankyou!

John - when you say that I may have been talking to call centre drongos, you're probably right. I'll go back and make sure I get a recording next time. I wouldn't mind but apparently I was speaking to the head of the department. I didn't take any names so I guess that was my fault.
I've re-read my email and as much as it seemed like I'd taken out all the emotion at the time, coming back and looking again I can see that it's still very obvious I'm fairly upset about all this.
Sorry, It's just that so far I've spent 6 hours on the phone, which is about 24 photos retouched (a decent bit of money when I can do it properly). Now it looks like I'm going to have to be on hold for another few hours tomorrow. I'm frustrated and I'm lashing out where I shouldn't. Sorry again. I've turned in a couple of pieces that looked fine on my (bluish) monitor but looked horrible when I was being shown why I'm getting less work now.
My main client pays for me to get a recalibration every 6 months but I'm finding I need one every few weeks. If I wasn't friends with someone that recalibrates monitors for a living I'd have to pay $100 a pop. I'm getting one every couple of weeks at the moment and I'm at the point of tearing my hair out here.
I'm saying this more so that you can understand where I'm coming from here rather than as some sort of justification of my earlier post. I know that I shouldn't be rude to people that are trying to help me and again, I'm sorry.
In terms of "another potential source of error" though, I should point out that I only came here as a last resort - I don't get this problem when I run any other applications on either laptop. I have spent a lot of time on the phone to both asus and acer over the last few months. I was a bit quick to point the finger but I've spent a lot of time ruling out other options.
I recognise that by saying it's your code's problem I'm almost saying that your baby is ugly and I really shouldn't have gone so far earlier. Honestly though, if you could at least give me some ammunition when I call the other various hardware support places I would be eternally grateful.
Wolf - As mentioned, I have a friend that can recalibrate my monitor for free. It's getting to the point where I'm being really demanding and he just keeps giving out of the goodness of his heart. I appreciate that that's what you guys are doing also and I hope people haven't been put off my the harshness of my earlier message. I'm just really really frustrated by all of this.

Will my Acer Aspire perform fine with Adobe Production Premium CS6?

I have an Acer Aspire and wanted to know if it will perform fine with Adobe Production Premium?
Intel Pentium T4500
Intel GMA 4500MHD
4 GB DDR3 Memory
500 GB HDD
Windows 7

That laptop of yours is far too weak for the type of video that you'll be editing. In fact, if a fast PC takes an hour (or a fast laptop takes three to four hours) for a given AVCHD content, your laptop may very well take all of three days (72 hours) to render that same amount of that same video. An analogy to this would be driving a beat-up old jalopy whose transmission is permanently stuck in first gear on a road that's designed to be used by modern high-performance sports sedans.
And in my experience, no dual-core CPU-based PC - not even a desktop - performs as fast in Premiere as even a quad-core CPU-based PC of merely average performance. In fact, my Core i3-2100-based desktop PC, though it was the fastest of all PCs with dual-core CPUs in the PPBM5 results list, is still outperformed by several laptops with quad-core CPUs.
Other bad points: The built-in screen has too low of a resolution to display the Premiere Pro interface properly. Some vital portions of the interface will be cut off, with absolutely no way at all whatsoever to retrieve this cut-off portion. This is because your display has a vertical resolution of only 768 pixels. Premiere Pro requires a minimum vertical display resolution of at least 900 pixels and a horizontal display resolution of at least 1280 pixels just to properly display the UI.

Acer Aspire v3-111P-C9Z3 SSD Upgrade issues

Hello I bought an Acer Aspire v3-111P-C9Z3 last summer and this summer bought an SSD to upgrade it with. I plugged the SSD in through my external USB dock, cloned the OS and tried running it. The seemingly simple operation ended when I got a "No Bootable Device" message from the Acer Bios. Running on legacy mode nets me a similar error. I used EaseUS to clone the OSI bought a 120g PNY SSDCLoned win10 the BIOS seems to recognize that the SSD is there (In the BIOS load order in the f2 screen it says something like " HDDSD-XXXXXXXXXXX" but it doesn't boot up the OS from the SSD the way that would be expected after being cloned. I appreciate anyone's help. I'm pretty computer-literate and have been looking around but have not found anything to fix this yet. Thanks

you can try to repair the cloned OS with a windows bootable media, boot from it and choose repair my computer then troubleshot and check if automatic repair/startup repair is able to fix it. Honestly, i would prefer to make a fresh install switching from HDD to SSD, since Windows makes some tweaks when installing on SSD (Trim, garbage collector, alignement)

Acer aspire v5 131 start up issues

Hello, I have an Acer aspire v5-131 and its 2 years old. It's windows 8 I got the message where I can auto update to windows 10 so I decided to do that but never noticed any difference. The problem where it can't get past the start up and there's 3 different types. 1. It shows the acer logo and the loading animation but then the screen goes black after 10 minutes. 2. It says preparing automatic repair then the screen goes black after 10 minutes. 3. It says "Scanning and repairing drive (C but stops at 47%. I've waited 3 hours but it still didn't progress after that.

if you don't have a recovery media, please download the iso for windows 10 and create a bootable media with it:https://www.microsoft.com/en-us/software-download/windows10 once done, try to boot from it, press F12 at boot and select your bootable media. if it boots try to enter safe mode as i wrote in my previous post.

Firefox Slow Even When Offline on Acer Aspire One ao751h-1145

I have a 2gb RAM, 1.33 Ghz Intel Atom CPU Z520, and a fresh install of Windows 7 Ultimate on my Acer Aspire One ao751h-1145. I have no viruses and no programs running in the background. I've installed and uninstalled various versions of Firefox (4, 11, 12) and even upon a fresh install before I edit preferences, bookmarks, or add-ons, the PROGRAM ITSELF is super slow. It isn't using any more RAM or processer speed that it should, however. What it does: Menus are slow to open, scrolling is jumpy, and switching from tab to tab takes like 2 seconds. Internet Explorer 8 works just fine, as do all other programs on the computer. Also, it works fine in Safe Mode. I can't find anything regarding this issue online. Help!

Thanks for reply. But, drivers are up to date. However, I found on this page (https://support.mozilla.org/en-US/kb/how-do-i-upgrade-my-graphics-drivers) that I might want to disable hardware acceleration. I did that through the options menu and Firefox is "usable," but still not what I'm used to on other computers and still not as fast as IE on the same computer. Since turning of the hardware acceleration helped, what else can I do along the same lines to speed it up more? I know a 1.33GHz processor is plenty fast enough to run only firefox by itself. The computer I'm on now (my non-netbook) runs at 700MHz when on batteries and has no performance issues. I hope I can get it because I don't want to use another browser! :(

Can't complete a clean installation of WIN 7 PRO on an Acer Aspire 4738

Hello,
If any one could help me with this problem i would really appreciate it.
I have an Acer Aspire 4738-6888 (icore 5, 3GB RAM, 500GB HD), it was running win 7 ultimate 32 bits but started working erratically so i decided to perform a clean installation. HD was formatted entirely.
Then tried installing WIN 7 PRO 64 bits from a DVD, but the installation program does not load and shows a kernel error oxc0000098
It is funny that if i use a WIN 7 PRO 32 bits DVD, the installation programs loads and starts, everything seems to run normally (HD partitions can be created and formatted, Files are expanded and configuration begins) but just after the third restart
when the assistant shows the message " preparing to run windows for the first time " the blue screen appears showing a "Memory_Management" error. Tried one more time but using a WIN 7 ULTIMATE 32 bits DVD with same results.
Finally, I tried using the "repair option" from the DVD and get this message:
StartupRepairOffline
01: 6.1.7600.16385
02: 6.1.7600.16385
03: unknown
04: 21350397
05: ExternalMedia
06: 1
07: FailureDuringSetup
OS version: 6.1.7601.2.1.0.256.1
Regional config: 3082
Before hand thanks a lot for your help,
Rgds,
GCH.

Hi GustavoCh,
What issue did you meet so you want to reinstall?
Could you please use the Windows install image to install Windows in other computer or virtual machine? So we can make sure this issue is not caused by the image.
I think this issue is related to hardware, please contact the manufacturer for better help.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

Performance issues w/LR 4.4

ugh...I am desperately searching for (more) ideas on how to make my LR 4.4(or my computer) run faster or perform quicker without taking forever to load catalogs/ previews and etc. Any suggestions on where I can look to get my computer to work better with LR 4.4? I didn't always have these issues and I have not loaded any new software BUT I DO still have LR 3 on my computer but I am not using it. I didnt realize when I loaded 4.4 that it would not simply update 3. I know that sounds lame but its true. Also, these problems did NOT begin when I loaded 4.4 but have begun the more I create and use new catalogs etc. I am somewhat of a novice on the workings of the files/memory etc but I use LR exclusively. Any ideas folks? I have changed a TON of my startup programs to not come on when I start my computer and I have defragged and ran virus protection, deleted cookies, temp files, programs I don't need or use.... and so forth. Everything I could imagine. I would appreciate any help. My computer is a year & a half old and I dont store onto it. I have 2 external drives where I store photo file originals and edits as well as any other files i need/use.I have an ACER Aspire X1430G with 4.GB (3.5useable) of Ram (and added 2 or 4- I cant recall- RAM) an AMD E-450 APU with 1.65 GHz HD Graphics. Yes...I am a moron... and I thank you for trying.
Thanks!
L

I've got this problem but it's not just with 3rd party accessories but also the apple headphones. It sometimes recognises that headphones are in and then randomly (upto 1 min) cuts out. When I press play (with the headphones still in) it plays through the speakers.
Is this just a faulty devices? I only got it last week...

Acer aspire 5670: Performance issues

Similar Messages

Maybe you are looking for