ACNS - Content Engine Pre-Positioning Video
Is it possible to load content onto a Content Engine CDNFS partition directly without using CDM? We have large videos that we would like to get the content from a PC to the Content Engine at the remote location
Hi,
The CDNFS partition and its database is managed exclusively by the CDM Manager. You can't upload files directly to that partition without using CDM. Thanks!
I hope this helps!
Regards,
Jose Quesada.
Similar Messages
-
Configuring a Content Engine to host Video
I have a customer whom has a Cisco CE 510 installed. currently they are using it just for Web Caching.
I remember reading at some point in the past that this Content Engine could serve video. Is this accurate? Is there any documentation to support this?
ThanksKevin,
Live and on-demand Video is definitely supported.
1. You need to figure out how to intercept the traffic you want to serve (wccp, proxy-pac, etc.) You may need to add services to your intercpetion technology.
2. You need to have a license for ACNS for Windows Media (and Real) support.
3. You may have to re-partition the drives for MediaFS if you want to cache VOD and CDNFS if you want to pre-position VODs and other files.
Here is a link for Video support in ACNS 5.5.
with CDM: http://www.cisco.com/en/US/docs/app_ntwk_services/waas/acns/v55/configuration/central/guide/9136strm.html')">http://www.cisco.com/en/US/docs/app_ntwk_services/waas/acns/v55/configuration/central/guide/9136strm.html
without CDM: http://www.cisco.com/en/US/docs/app_ntwk_services/waas/acns/v55/configuration/local/guide/wmtstrm.html')">http://www.cisco.com/en/US/docs/app_ntwk_services/waas/acns/v55/configuration/local/guide/wmtstrm.html
Hope that helps,
Dan -
File attachment size on CSS/ ACNS/content engine
Our great Peoplesoft developers raised the question whether the CSS/ACNS/ContentEngine are capable of detectng the size of the attachment and if it possible to set the allowable size.
Aparrently, the great Peoplesoft don't do this and guess what they pass everything to Comms to solve their freaking problem.
Thanks in advance.
BenjaminI saw your previous query for the same question and decided at that time to not answer to see if sb else had an idea but since you ask it again, the answer is "not possible".
Gilles. -
Content Engine caching video content?
I am currently running ACNS version 5.5.11.2 on a CE510 Content Engine. I recently had to replace the unit and when I set up the partitions for the new build, I elected to go with CE510#disk config sysfs 10% cfs 45% mediafs 45%.
Before the cfs was setup to use the whole box. I was thinking that the mediafs partition would start to cache video content. Does that happen automatically or is there some other setting to make that happen further. How do I determine if it is getting any use?A content engine can cache files transfered via ftp but not https [as the content is encrypted].
It can cache whatever file, including video, audio, ...
Content routing, content switching are just names.
They refer to how the traffic will be intercepted and forwarded to the content engine.
You could simply use a proxy solution and have your users setup their browser to use the content engine as a proxy, or you could transparently intercept http/ftp traffic via a router running wccp, or you could use a Layer7 device like a CSS to intercept the traffic and redirect to the content engine.
Regards,
Gilles. -
Content engine for video on the LAN
Hi
I have a video server on the LAN. I want to position the content engine on the LAN to use it for stream splitting to avoid loading the video server. Can i do this i.e. placing the Content engine on the same network as the source? Or could I use the Content engine module on the router. If so then how do I connect it?
Thank you
SanjI suggest that you use the content engine module on the router.
-
Content Engine NM ACNS/network access
After searching Google and Cisco, here's my setup...
2851 Router running 15.1T
CE-NM-BP-80G-K9 in slot 1/0
Bridge group 1 for LAN and Wireless WIC.
Goal: Either add the external CE interface to the LAN on the bridge group or use WCCP to cache traffic through the internal interface.
I was able to access ACNS once, but I'm completely new to the design and it was only for testing with the IP scheme. I reset the config, reloaded the router and now I can't access ACNS via the web gui nor can I access the network from the CE (ping or ftp).
Interface ContentEngine 1/0 Config:
ip address 10.0.0.1 255.255.255.0
Service Module ip address 10.0.0.2 255.255.255.0
Service Module external ip address 10.0.1.1 255.255.255.0
Service Module ip default gateway 10.0.0.1
Interface BVI1
ip address 192.168.2.1 255.255.255.0
using dhcp etc
Service module config:
CE#sh run
! ACNS version 5.5.3
hostname CE
http proxy incoming 80 8080
ip domain-name mydomain.com
interface FastEthernet external
exit
interface FastEthernet internal
exit
wmt evaluate
wmt accept-license-agreement
wmt enable
ip name-server 8.8.8.8
ip name-server 192.168.2.1
wccp router-list 1 192.168.2.1
wccp web-cache router-list-num 1
wccp reverse-proxy router-list-num 1
wccp wmt router-list-num 1
wccp version 2
username admin password 1 xxx
username admin privilege 15
username xxxx password 1 xxx uid 2001
username xxxx privilege 15
authentication login local enable primary
authentication configuration local enable primary
cdm ip 192.168.2.1
! End of ACNS configuration
Here's what I get when attempting to ping:
CE#ping 192.168.2.1
connect: Network is unreachable
CE#ping 10.0.0.1
connect: Network is unreachable
CE#ping 10.0.1.1
connect: Network is unreachable
And from the LAN:
seth@Sony:~$ ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
64 bytes from 192.168.2.1: icmp_req=1 ttl=255 time=1.79 ms
^C
--- 192.168.2.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 1.799/1.799/1.799/0.000 ms
seth@Sony:~$ ping 10.0.0.1
PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data.
64 bytes from 10.0.0.1: icmp_req=1 ttl=255 time=1.39 ms
64 bytes from 10.0.0.1: icmp_req=2 ttl=255 time=1.93 ms
^C
--- 10.0.0.1 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 1.396/1.666/1.936/0.270 ms
seth@Sony:~$ ping 10.0.0.2
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
^C
--- 10.0.0.2 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 1006ms
seth@Sony:~$ ping 10.0.1.1
PING 10.0.1.1 (10.0.1.1) 56(84) bytes of data.
^C
--- 10.0.1.1 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 1007ms
Page cannot be displayed when attempting to hit the CE on port 8001 or securely at 8003 although the CE shows it's listening
CE#sh gui-server
GUI Server is enabled
Listen on port 8001
Secured GUI Server is enabled
Secured GUI Listen on port 8003
Let me know if there's some other pertinent info, but what am I missing?SOLVED --
The mistake was my own...in writing this post and re-testing, I realized I had made a foolish mistake. I applied an access-list (which I forgot to include) to the "ip wccp web-cache redirect-list bypass_content_engine" in the global config of the router.
When I installed service 95 for spoofing, I automatically added the same access list to it as well.
This was not a good thing since the access list denied packets with a destination of our internal IP addresses from going through the content engine. This worked fine on the way *out* of the router. But as the now-spoofed packets returned, their destination was an inside IP address and they were pretty much discarded. Foolish Mistake!
Removing the ACL from the "ip wccp 95" statement in the global config fixed the issue and I am spoofing fine.
Sorry to waste time...
David Hunter -
Smartfilter with Content Engine Module (NM-CE-BP-40G-K9) & ACNS on 3661
I've been looking over the CCO docs, but can't find one that has sample configs for using a 3661 router containing content engine module, smartfilter, & ACNS. Topology is basically the following...
(PC's)----(LAN Switch)-----(3661 w/content engine module)----(PIX)---(internet)
I don't want to creat a new IP subnet for the 3 interfaces within the content engine module/router. I want to use the IP's from the current LAN IP Block.
Any advice appreciated.I thought this might help.
Easy NM-CE Configuration Guide!
Router IOS:c3725-ik9o3s-mz.122-15.T2
Content Engine Software: ACNS 5.0.3.5
Configure basic router configuration as normal.
Set the IP addresses for the Service Module (Content-Engine) using these commands:
interface Content-Engine2/0
ip address 10.1.1.1 255.255.255.0
ip nat inside
service-module external ip address 10.0.0.1 255.255.255.0
service-module ip address 10.1.1.2 255.255.255.0
service-module ip default-gateway 10.1.1.1
Complete Config Example (DHCP and NAT for Lab):
urrent configuration : 2440 bytes
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname lab3745_NM-CE
logging queue-limit 100
enable password cisco
ip subnet-zero
ip wccp web-cache
ip dhcp pool NM-ESW-16-POOL
network 10.1.2.0 255.255.255.0
domain-name cisco.com
default-router 10.1.2.1
dns-server 171.68.226.120 171.70.168.183
lease 7
ip audit notify log
ip audit po max-events 100
no voice hpi capture buffer
no voice hpi capture destination
mta receive maximum-recipients 0
interface FastEthernet0/0
ip address 172.16.12.108 255.255.255.0
ip wccp web-cache redirect out
ip nat outside
duplex auto
speed auto
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface FastEthernet1/0
no ip address
interface FastEthernet1/1
no ip address
interface FastEthernet1/2
no ip address
interface FastEthernet1/3
no ip address
interface FastEthernet1/4
no ip address
interface FastEthernet1/5
no ip address
interface FastEthernet1/6
no ip address
interface FastEthernet1/7
no ip address
interface FastEthernet1/8
no ip address
interface FastEthernet1/9
no ip address
interface FastEthernet1/10
no ip address
interface FastEthernet1/11
no ip address
interface FastEthernet1/12
no ip address
interface FastEthernet1/13
no ip address
interface FastEthernet1/14
no ip address
interface FastEthernet1/15
no ip address
interface Content-Engine2/0
ip address 10.1.1.1 255.255.255.0
ip nat inside
service-module external ip address 10.0.0.1 255.255.255.0
service-module ip address 10.1.1.2 255.255.255.0
service-module ip default-gateway 10.1.1.1
interface Vlan1
ip address 10.1.2.1 255.255.255.0
ip nat inside
ip local pool NM-ESW-16-POOL 10.1.2.2 10.1.2.254
ip nat pool TEST-NAT-POOL 172.16.12.108 172.16.12.108 prefix-length 24
ip nat inside source list 7 pool TEST-NAT-POOL overload
ip http server
no ip http secure-server
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.12.254
access-list 7 permit 10.1.2.0 0.0.0.255
access-list 7 permit 10.1.1.0 0.0.0.255
access-list 7 permit 10.0.0.0 0.0.0.255
call rsvp-sync
mgcp profile default
dial-peer cor custom
line con 0
speed 115200
line 65
flush-at-activation
no activation-character
no exec
transport input all
line aux 0
line vty 0 4
password cisco
login
end
reset service-module 2 to reboot the Content-Engine:
service-module content-Engine 2/0 reload
Within 30 Seconds Session from the Router to the Service Module:
service-module content-engine session
Enter Basic Configuration for Network Module:
Password, etc
Configure The service Modeule using the command line interface:
hostname NM-CE-BP
ip domain-name CISCO.COM
interface FastEthernet 0/0
ip address 10.0.0.1 255.255.255.0
exit
interface FastEthernet 0/1
ip address 10.1.1.2 255.255.255.0
exit
ip default-gateway 10.1.1.1
primary-interface FastEthernet 0/1
ip name-server 172.72.1.1
wccp router-list 1 172.16.12.108
wccp web-cache router-list-num 1
wccp version 2
username xxx password xxxx
username xxxx privilege 15
authentication login local enable primary
authentication configuration local enable primary
NM-CE-BP#exit
You can use the command line interface to show statics from the Content Engine by using the show statistics screen command or use your web browers for a more graphical report. -
Content Engine compatability with Windows Media Player
I am currently running ACNS version 5.5 on our CE510 Content Engine. We want to set this box up to serve VOD requests from WMT. I think the clients on site are all using Windows Media Player version 10. Does this version of ACNS software work with Windows Media Player 10?
Dan
this brings up an interesting point. The content (which is canned Video on an Intranet Web site) is HTTP? I am wasting my time here by trying to use the Windows MP services?? Perhaps I already have what I need...
Your comments appreciated.
Kevin -
Dear All Experties,
We are using a Cisco Content engine 7325 as a proxy server.recently we brough WAE-674 as a replacement of these old content engine.After turn on WAE-674,Blue screen pop up on moniter.I am not able to access anything with GUI as well through command line.That why i am not able to configure that one.
Please advise me if anybody else also faced this problem or if anybody have any idea what i can do ???
Thanks in advanceHi,
How are you connected to the WAE?
If you are directly connected to the WAE through a screen/keyboard, what you see might be expected: the WAAS/ACNS software stop redirecting it's console output on the screen after booting it's kernel and move it to the serial port.
This is explained in the hardware specs of your device:
You can connect a keyboard to any USB port and connect a monitor to the video connector to troubleshoot the BIOS boot process. However, video output is for troubleshooting only during the BIOS boot process. The video output stops displaying when the serial port becomes active. To monitor the boot process in normal operation, use the serial console port.
http://www.cisco.com/en/US/partner/docs/app_ntwk_services/waas/wae/installation/7341-7371/guide/7300intr.html#wp1040565
Could you have a look at the boot sequence from the serial port and see if everything looks fine from there?
Regards,
Nicolas -
Help!!! Content engine
my configuration is follow the attached file. I don't know what is wrong with my content engine using as a cache server. when i connect this CE to my network, i can make my user access to the internet fast only 2 days, but after 2 days it makes my users internet connection slow. So when users access to the internet slow, i disconnect this CE from my network, then my users internet connections is running better. So please help me to find what is incorrect with my configuration and what commands i should add more to this current configuration"
What is the ACNS software version u r using in ur content Engine7305.I am sending u a configuration doc for ACNS rlease 5.2.This has all the info regarding ACNS 5.2.
http://www.cisco.com/en/US/products/sw/conntsw/ps491/products_configuration_guide_book09186a00802debd6.html
Let me know, if you have any problem in browsing this big document. and finding out the pblm.I will assist you. -
Dear All,
My apologies if this posting is on the wrong board.
I've a problem with our content engine returning an error of:
"Tre reply from server is not valid"
The URL of the site is http://hiring.monster.co.uk/jobs/createtitle.aspx?mode=qb.
I've attached a screenshot of the error message.
Any advice or help would be greatly appreciated.
Thank you in advance.
SinhThis symptom is observed on a router on which Web Cache
Communication Protocol (WCCP) is enabled and Cisco Express Forwarding (CEF)
switching is disabled. If the caches are Cisco caches, they will be running
software prior to ACNS 4.2.5.
solution: Ensure that CEF switching is enabled on the router. If this is not possible, the impact of the problem on the cache will be minimized if the authentication bypass function is disabled.also try upgrading IOS to 12.1(18.01)E which may solve the issue. -
Should the Content Engine work while the Inernet link is down ?
I have installed CE590 in a client network
The http saving performance is from 30 : 40 %
My client want to make sure the CE is caching the web site
He want to shutdown Serial port of the main router , and try to browse web sites. ( the Cached sites )
Should he get a reply from the CE and browse the cached sites ??
I mean , Can the PC browser ( while the internet is link is down ) open page like www.yahoo.com for example if it is cached on the CE ??
Is there is any command of the CE that can display the name of the cahced web pages ?
Note : Cisco Content Engine Software Release 3.11
Can anyone help me ?
Thanks
Mohamed AbdallahMohamed,
Before you go any futher you need to upgrade the CE to ACNS 4.2.3. There are known issues with 3.1.1.
To answer your question the CE will only server content if it can not access the internet if the object is fresh. By this I mean the object has not expired or the object does not need revalidation eg If modified since request.
This could cause problems with broken pages etc etc.
Your best option is to turn on transaction logging.
transaction-logs enable
You can then go to the local1/logs directory on the CE
type working.log
This will show you the urls that clients are requesting and if they got a hit / miss/ ims hit / ims miss etc etc.
Overall your cache should always have access to the origin server for content.
Cheers
Phil -
Positioning video in fixed layout epub
Hi.
How can i positioning video in fixed layout page?
here is the xhtml contents.
<video src="videos/video1.mp4" poster="images/video1.png" width="300" height="200" preload="auto" controls="true"></video>
I want to change position of video but don`t know how.
I used "top", "left" property but it not work.
<video src="videos/video1.mp4" poster="images/video1.png" top="100" left="200" width="300" height="200" preload="auto" controls="true"></video>
I saw book in iBookstore "The Beatles Yellow Submarine" and see video can move any position.
Please help.
Thanks.Hi Lifelab,
I have the exact same problem! Did you happen to fix it by now? Please, it would really help me.
Thanks
Dina -
Content engine 565 - real server relay
hi all,
we have a standalone content engine 565 running acns 5.3.1. we would like to realize something like a live stream 'relay':
we place the ce on the network edge and it receives a live stream (rtsp) directly from a content provider. the internal clients send their rtsp requests for that live stream directly to the ce which answers the requests. one important thing is that we cannot use a proxy configuration, because a proxy config on the client is not possible - meaning that we need to place requests directly (no direct or transparent proxy). in the real subscriber config interface I saw the receiver/transmitter section - is that the right way to go? where can I find config examples or documentation for that issue. on the cisco website I could not find any detailed documentation for real subscriber configs.thanks for the answer - i realized it rather late. can you help me in configuring this setup? as i said I cannot find any documentation support for such a setup...I would really appreciate any help.
thanks,
daniel -
Content Engine cannot authenticate using LDAP
Dear All,
I have a problem with content engine 511 authenticating with LDAP server. I am using Lotus notes LDAP server to authenticate with content engine but it doesn't work. Anyone has try with LDAP before? Please advice. Thank you for your help.
Regards,
ChrisDear,
I already using the latest version of ACNS software 5.3. And there is an option to use LDAP authentication in CLI and WEB based management. Thank you for your help.
Regards,
Chris
Maybe you are looking for
-
If I send my Zen Touch in to Creative, will they delete my da
Here's the story. I got a Zen Touch from my parents for Christmas, and I was thrilled. I put on about 9 GB of music in the first few weeks. Then, poof, it freezes my computer when I try to connect to it. It was working fine the day before, and nothin
-
Generate outbound idoc for Customer Master
Hi Developers, I have requirement to generate outbound IDOC for Customer Master Data. I need to send customer master data through an Outbound IDOC. Can we generate an outbound DEBMAS06 idoc? Can someone help me finding a solution to this problem? Tha
-
SAP Cloud for Customer & SAP ECC/CRM OnPremise integration using WebServices!
Hello All, I would like to ask if anyone has really created a working integration scenario between a Cloud Solution & an ECC/CRM OnPremise solution? We are trying to build some prototypes for this, however, due to connectivity errors/issues, unable t
-
New to Business Graphics in WD ABAP
Hi all, I am new to Business Graphics in WD ABAP. I have already go through the WDR_TEST_EVETS. But I don't get it clearly. Is there any other document or any earlier thread to understand BG. Please suggst. Thanks Sanket sethi
-
How to crop to a specific aspect ratio, then resize to specific size?
HI, I need a running start, could someone please help me accomplish a specific task. 1) I need to be able to restrict a crop tool to a specific aspect ratio, then resize the cropping tool as I like to make my selection. 2) After, I need to resize