ACS 4.2 HW appliance Change speed + duplex

On The ACS Hw appliance how do you configure the speed and duplex ? Currently my sw is set to 100 full and my ACS keeps on negotiating to 100 half. Any suggestions ?

Hi
Each NIC is configured to automatically detect the speed and duplex mode of the network.
Please observe the following cabling restrictions for 10BASE-T, 100BASE-TX, and 1000BASE-TX networks:
â¢For 10BASE-T networks, use Category 3 or greater wiring and connectors.
â¢For 100BASE-TX and 1000BASE-TX networks, use Category 5 or greater wiring and connectors.
â¢The maximum cable run length is 328 feet (ft) or 100 meters (m).
Regards

Similar Messages

Change speed, duplex, auto negotioation of NIC using Powershell or command line

Hi
I created Hyper-V cluster using nodes with Microsoft Hyper-V server 2012R2. So these nodes don't have GUI. How to change for example NIC speed? I have 1GB NIC but in system autonegotiation use 100MBps? How to force 1gps speed.
This is one of example. Using Power Shell Get/Set-NedAdater commands don't have power to do it.
Thank you for help!
Kind Regards Tomasz

Is this the nic on a VM or on a VM Host?
A physical NIC can usually only be changed by the vendors utilities. A VM can change NICs in the config file.
This might be helpfulk in deciding:
https://social.technet.microsoft.com/Forums/windowsserver/en-US/8746cfc4-df49-4b12-9e66-81d80605e717/configure-hyperv-vm-nic-speed?forum=winserverhyperv
¯\_(ツ)_/¯

Change NIC speeds/Duplex of all machines by script or other ? Is it possible

Hi, we need to change the duplex settings ona all our desktops. Anyone know if this can be done via script or any other way please ?

Hello joebhoy,
These steps may vary a little but should provide some guidance for you.
Click here
Instead of choosing auto-negotiate, select desired link speed.
Best regards,
Bgriffin2
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

How to change Speed?

Hi,
I'm using 2960 with GLC-GE-100FX= .
I can not change Speed from Auto to 100MB.
Please advice how to change Speed.
Current I/F setting is as following,
Switch#sh int gi 0/1
GigabitEthernet0/1 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 0025.b42a.d919 (bia 0025.b42a.d919)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Full-duplex, Auto-speed, link type is auto, media type is 100BaseFX SFP
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Best regards,
Ichiro

Hi Leolaohoo,
Thank you for your prompt reply and exact answer.
I connected Fiber optic cable to SFP. Speed became 100Mb/s from Auto automatically.   Thanks!
Best regards,
Ichiro

IPS Speed & Duplex settings

I have a 4240 inline between an ASA and a Switch, and am experiencing errors on the switch indicating receive discards.
The devices are directly connected like this, ASA --- IPS --- SWITCH. The ASA and Switch have the speed/duplex fixed to 100/Full, but the IPS is auto negotiate. Both ports have negotiated to 100/Half, which I believe is causing the issue (open to alternative suggestions) however if I change to fixed parameters I loose connectivity. How should these connections be configured to remove the errors?

Network Interfaces do not support fixed configuration of speed and duplex on one device and auto negotiate on the other device.
The device set to auto negotiate will send out negotiation queries to the other device, but because the other device is fixed it will not respond to the queries. The devices with the fixed speed and duplex does Not respond with the fixed speed and duplex, and instead just simply does not respond at all to the auto negotiation queries.
So the device with auto negotiation is not able to determine the settings for the other device, and will set it's own speed and duplex to the default settings for that NIC. On most 10/100 and 10/100/1000 copper interfaces the default will be 100 Half Duplex.
So for auto negotiation to work properly you Must set Both devices to auto negotions.
If you will fix speed and duplex on one device, then you must also fix speed and duplex on the other device.
The other thing to keep in mind is the type of cable connecting the 2 devices.
For 10/100 interfaces you have to be very carefull of the type of cable being used. When connecting the sensor to a switch it must be a standard cable. BUT when connecting the sensor to a Firewall, Router, or PC, then it likely needs to be a CrossOver cable. (The switch has built in the equivalent of crossover directly within its ports, but firewalls, routers, etc... generally do not)
If you are using 10/100/1000 interfaces on both devices, and have both devices set to auto negotiate; then in most cases the type of cable will not matter. When auto negotiate begins they will determine the cable type and one of the 2 will automatically do a sort of internal crossover if needed, and will then auto negotiate to 1000 Full.
HOWEVER, if you fix the speed and duplex then just like with 10/100 interfaces you have to be very carefull that you are using the right type of cable. There will not be any negotiation and so your cable choice must be very specific. In most instances you will need to use a crossover cable when connecting the sensor to a Firewall or Router, but use a standard cable when connecting to a switch.
So be sure to set speed and duplex the same on both devices. Either both devices with fixed speed and duplex, or both devices with auto negotiated speed and duplex.
And be sure you are suing the right type of cable for your particular connections.

K9a2 plat. v2. unable to change speed on my case fan

Hi!
I just bough a 80mm case fan and I can't change it's speed using the BIOS or from within the OS using speedfan.
The fan in question is a Zalman ZM-F1 with a 3 pin connector.
The motherboard can detect the fan speed. (3000rpm, so it's registering it correctly) but I have so far been unable to change it's speed. I can't figure out why, since i have a 120mm no-name fan which it detects changes speed just fine.
The 120mm is connected to sysfan 1 (works)
The 80mm zm-f1 is connected to sysfan2 (doesn't work)
I know that I can use a connector to the psu to perma-run the fan in silent mode, but the thing is that i want to be able to control the fan from BIOS (and OS). I can't figure out why i cant control the speed since the bios is able to detect it Could this be a BIOS issue?
I've been trying to find something about this issue for myself but this is all i've managed to come up with so far :
In this link it's mentioned that some motherboards can't monitor the fan speeds. I'm however able to see the fan speed.. so why can't it be changed? hmm..
http://www.quietpcusa.com/Zalman-80mm-Quiet-Computer-Fan-with-3-Pin-Connector-ZM-F1-P73C6.aspx
I hope that some of you might be able to shed some light over the situation. I'm at a loss here.
Best wishes
/Cawanga
K9A2 PLATINUM V2
BIOS ver. 1.5
AMD Phenom 9750 2640MHZ@220 FSB
Corsair 2x2048-6400
ATI 3850 CF
Corsair 740w PSU
Maxtor 6L300S0 300GB, Western Digital WD2000JD 200 GB, Samsung HD103UJ 1TB
Lite-On LTR-48246S CDRW, NEC ND-3500AG DVDRW
Win XP Pro 32-bit SP3

As you can see in BIOS (H/W Monitor) the only Fan Header that allows fan regulation is SYSFan1. I am afraid there is not much you can do besides:
Quote
I know that I can use a connector to the psu to perma-run the fan in silent mode,

Speed/Duplex are not advertising correctly with configured values

Hi,
I have a gateway which runs on Windows Embedded Standard 7 which has Intel NIC Card.
I have connected this gateway and a switch in a network where switch has configured speed/duplex as 1000Mbps/Full.
When I set the Speed/Duplex on my gateway's NIC to Auto-Negotiate or 1000Mbps/Full, it negotiating/advertising the speed and duplex properly.
But when Speed/Duplex sets to 100Mbps/Full on gateway's NIC, in the Switch it shows that my gateway is advertising the Speed/Duplex as 100Mbps/Half Duplex.
I have checked the registry entries which sets when we configure the Speed/Duplex at adapter properties, registry entries are fine. I am not able to understand how exactly it negotiates Speed/Duplex and why it is advertising with 100Mbps/Half Duplex when
it is configured for 100Mbps/Full.
Thanks,
Challask

Hi Andy,
Thanks for the reply.
I have checked that the configured value on the adapter is 100Mbps/FullDuplex. I am checking these configured values through the registry entry
Computer\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}\00NN\*SpeedDuplex. It shows the configured value.
The doubt have here is that i have checked the enum values for this *SpeedDuplex entry, it shows in the following way:
0 - Autonegotiation
1- 10Mbps HalfDuplex
2 - 10Mbps FullDuplex
3 - 100Mbps HalfDuplex
4 - 100Mbps FullDuplex
6 - 1000Mbps
Why don't have here the value 5?
I have checked this registry in other Windows Operating systems, it shows correctly. Only in this Windows Embedded Standard 7 OS it shows this way. Will it create any issue? While performing the Speed/Duplex advertisement/Negotiation will it use these enum
values? If so how can I resolve this issue?
Thanks,
Challask

Problem to change speed of my plan

Hello,
when i want to change speed of my plan, it's impossible because there's an error at the time of trim operation.
What can i do to solve this problem.
Thank you
Sof Gasiglia

See if this helps
http://www.fcpbook.com/Video7.html

Any way to change speed of a clip in "over-write edit" mode?

I want to change the speed of a clip in the timeline without having to lock all the other tracks or having to move the other following clips out of sync. For example I have a clip which lasts for 1 sec, which I want to change to 3 secs. Normally when I do this in the timeline the other clips on the same video tracks which follows, will move their position..... How to change speed in "over-write edit mode"?

I think it's even easier to just match frame the "source file"... put your playhead on the clip you want to speed change in your sequence. Then type optioncmdf. Perform the speed change in the Viewer, then simply cut it in... Might help to put it up above the older, use the double arrow selection tool facing right to move the clips past this change later... pull the upper track speed changed clip down over the old, and viola.
Gotta say though, it's a lot easier to perform the speed change in the Viewer, and edit it all in as you go rather than doing it after you've put the clip in a sequence. (not always possible to determine what the speed change should be maybe, but sure easier.... FCP 7 handles this problem a lot better for sure, and worth the upgrade price if your machine is compatible.
Jerry

Podcast how to change speed from 1.5x to 1x speed without having to go through 2x, 3x etc?

Podcast how to change speed from 1.5x to 1x speed without having to go through 2x, 3x etc?

Whereas I need to be
able to go from disc 1/track 1 to disc 1/track 2,
instead the iPod goes from disc 1/track 1 to disc
2/track 1.
Right click on any of these files and do a Get Info. Notice that there is, in fact, a Disc number field. So you can make disc numbers 1/10, 2/10 and so on.
iTunes and the iPod are both smart enough to recognize that there are disc numbers there and act correctly. So it'll start with Disc 1, play all that disc, then go to Disc 2, and so forth. It's just a matter of having correct disc number tags.
You can tag disc numbers for a whole disc at once. Simply select all the songs in a single disc (hold SHIFT or CTRL while selecting the songs), right click, Get Info, and you get the mass tag editor screen. Add the disc number info for this disc, and it'll tag that info to all those songs. Repeat for each disc.

Best way to change speed of clips

Hey, I want to change speed of clips, both faster and slower in one clip. What is the best way to do that preserving the quality? I am still learning FCP so my apologies, and I had a hard time finding anything on here through search.

Jerry's right...
Take a look at this:
http://homepage.mac.com/captmench/SlowMo3.mov
Two frames each of FCP and Shake at 50%. Use your arrow keys to go frame by frame. First frame is normal, second is interpolated. Look at the background!!
Creative cow should have the whole tutorial online soon... I'll post back with the link when they do.
Also, for time remap -- shake's got that under control too... but for now, look at this:
http://www.proapptips.com/proapptipsvideotutorials/879F6B61-CFF9-4FD1-8D43-FDF89 605611A/D95A1854-BE2C-46A6-A064-FA0A2306E254.html
Good luck,
CaptM

Speed/Duplex between two different switchs & SFP

Hi everybody,
I'm sorry about my poor english... I'm French (but it is not contagious)
I need your help (or TAC Help ) about speed and duplex problems.
My network :
[C2960G-24TC-L with sfp GLC-FE-100LX on Gig 0/23] <--> (Singlemode Fiber 9/125µ) <--> [Cisco SF200-24 with sfp MFELX1 on Gi1]
Autonegociation everywhere...
My problem :
%CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet0/23 (not full duplex), with f02929f97095 gi1 (full duplex).
- I can't force speed/duplex on MFELX1 (actually a-full a-100)
- I can't force speed/duplex on GLC-FE-100LX (actually a-half a-100)
Is there an incompatibility between this equipements ?
Configuration detail :
WS-C2960G-24TC-L   12.2(58)SE2           C2960-LANBASEK9-M
Cisco SF200-24 Firmware Version (Active Image): 1.2.9.44
#sh int gig 0/23 capabilities
GigabitEthernet0/23
Model:                 WS-C2960G-24TC-L
Type:                  100BaseLX-FE SFP
Speed:                 100
Duplex:                half,full
Trunk encap. type:     802.1Q
Trunk mode:            on,off,desirable,nonegotiate
Channel:               yes
Broadcast suppression: percentage(0-100)
Flowcontrol:           rx-(off,on,desired),tx-(none)
Fast Start:            yes
QoS scheduling:        rx-(not configurable on per port basis),
                         tx-(4q3t) (3t: Two configurable values and one fixed.)
CoS rewrite:           yes
ToS rewrite:           yes
UDLD:                  yes
Inline power:          no
SPAN:                  source/destination
PortSecure:            yes
Dot1x:                 yes
Multiple Media Types: rj45, sfp, auto-select
#show int gigabitEthernet 0/23 transceiver properties
Diagnostic Monitoring is not implemented.
Name : Gi0/23
Administrative Speed: auto
Administrative Duplex: auto
Administrative Auto-MDIX: on
Administrative Power Inline: N/A
Operational Speed: 100
Operational Duplex: half
Operational Auto-MDIX: on
Media Type: 100BaseLX-FE SFP
Configured Media: auto-select
Active Media: sfp
Thank you so much for yor help !

Thank you Leo,
It doesn't work, but I found an solution !
A strange solution...
I forced the C2960G-24TC-L to work with SFP :
media-type sfp
When I do that, I have the possibility to force the duplex (but not the speed... ok why not... ) :
duplex full
It is not very clean but my link is up and full-100 both sides.
Not very clean because :
C2960 side = force duplex, auto speed
SF200 side = auto duplex, auto speed
No errors... the link is clean.
Anyone known the reason or a better solution ?

Way to change speed of entire Project easily?

Hi, I know how to change the speed of an individual clip in the timeline - but is there an easy way to change the entire speed of the project? Thanks.

Hi, thanks guys - that worked - although it seems when I change the speed of the nested sequence and export it the quality is quite a bit worse (exporting it with the same settings) - seems to be a lot of jagged edges now. Is there something in the 'Change Speed' window that should be changed? I am creating a sequence and doubling the speed and another sequence exported with 4 times the speed. What is checked in the Change Speed window is 'Frame Blending' and 'Scale Attributes' (the default settings). Any ideas how to get rid of the 'jaggedness' that is being created? (this file was originally a .dv file - a regular export to quicktime from regular speed sequence looks fine. Thanks.

Firefox 5 does not remember changed speed tweaks. Every time I close the browser they revert to the standard setting..what gives!

Firefox 5 does not remember changed speed tweaks. Every time I close the browser they revert to the standard setting..what gives!'''bold text'''
'''Moderator note: Locked as dupe of [https://support.mozilla.com/en-US/questions/843444 843444] --T'''

Now up to Firefox 8 and the problem persists. Cannot go to the www.turnitin.com page and login as I used to do -- Firefox does not remember my username or password.
Still works on Windows, and with other browsers... It would be great if a fix is available.

Quickest way to change speed but not clip duration

I'm trying to determine the fastest method for changing the speed
of a clip already in the timeline, but not the clips duration. Primarily, slowing a clip down.
The best I've come up with so far is to put the timeline playhead over the
clip and hit X to get the clips IN and OUT points placed in the timeline. Then,
drag the clip into the Browser, effectively making a copy of it there. Then bring the clip into the Viewer, then hit APPLE J to bring up the speed change window, affect the change, then overwrite the change you've made in the viewer back down into the timeline where you placed the original IN and OUTS. Seems like alot of step.
Is there a faster way? Any change I try to make in the timeline itself results
in a clip duration change. The only other way I've found it to use the time remap tool put that is even more complicated and is alot less exact when trying to make something, say, 50% slower.
Any input would be appreciated.

Another, close but not quite there method I've tried is the TIME REMAP tool
that lives with the SLIP AND SLIDE.
I can affect speed changes, and see what percentage speed change I'm
trying to make, but it wants to change speed on both the left and right side
of the clip. In other words, I can't place the timeline playhead or Time remap tool at the beginning or end of the clip and only effect the speed of the entire
clip unless there is no clip adjacent to the clip I'm trying to change.
Otherwise it changes the speed as I want for 99% of the clip and then during
the last several frames I've accidentally sped up up those frames. I can't position it to just change the speed for the entire clip.

ACS 4.2 HW appliance Change speed + duplex

Similar Messages

Maybe you are looking for