ACS 5.4 AD Join strange Issue

Hi,
We have two ACS boxes with the same software version (5.4.0.46.0a), we were able to join domain one ACS only and other ACS is given the attached error.
When we checked "main-acs-01/admin# acs troubleshoot adcheck <domain-name>, it gave the same error for both ACS, however one ACS successfully joined to the domain and still other one failed.
main-acs-01/admin# acs troubleshoot adcheck <domain-name
This command is only for advanced troubleshooting and may incur a lot of network traffic
Do you want to continue?  (yes/no) yes
OSCHK    : Verify that this is a supported OS                          : Pass
PATCH    : Linux patch check                                           : Pass
PERL     : Verify perl is present and is a good version                : Pass
SAMBA    : Inspecting Samba installation                               : Pass
SPACECHK : Check if there is enough disk space in /var /usr /tmp       : Pass
HOSTNAME : Verify hostname setting                                     : Pass
NSHOSTS  : Check hosts line in /etc/nsswitch.conf                      : Pass
DNSPROBE : Probe DNS server 172.24.1.1                                 : Pass
DNSPROBE : Probe DNS server 172.24.1.2                                 : Pass
DNSCHECK : Analyze basic health of DNS servers                         : Pass
WHATSSH  : Is this an SSH that DirectControl works well with           : Pass
SSH      : SSHD version and configuration                              : Note
         : You are running OpenSSH_5.3p1, CiscoSSL 0.9.8r.1.3.
DOMNAME  : Check that the domain name is reasonable                    : Pass
ADDC     : Find domain controllers in DNS                              : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                     : Pass
ADPORT   : Port scan of DC xxxx.<domain-name>                      : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                    : Pass
ADPORT   : Port scan of DC xxxx.<domain-name>                     : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                     : Failed
         : Cannot resolve the IP address for xxxx.hmc.org.qa.
ADDNS    : DNS lookup of DC xxxx.<domain-name>                     : Pass
ADPORT   : Port scan of DC xxxx.<domain-name>                      : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                  : Pass
ADPORT   : Port scan of DC xxxx.<domain-name>                   : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                    : Pass
ADPORT   : Port scan of DC xxxx.<domain-name>                     : Warning
         : One or more ports failed to respond correctly. Either:
         :   a) the DC is offline
         :   b) a firewall is preventing access to a port
         : The following is a list of failed ports:
         :    ldap(389)/udp - timeout
         :    smb(445)/tcp - refused
         :    ldap(389)/tcp - refused
ADDNS    : DNS lookup of DC xxxx.<domain-name>                       : Pass
ADPORT   : Port scan of DC xxxx.<domain-name>                        : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                       : Pass
ADPORT   : Port scan of DC xxxx.<domain-name>                        : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                          : Pass
ADPORT   : Port scan of DC xxxx.<domain-name>                           : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                   : Pass
ADPORT   : Port scan of DC xxxx.<domain-name>                    : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                     : Pass
GCPORT   : Port scan of GC xxxx.<domain-name>                      : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                    : Pass
GCPORT   : Port scan of GC xxxx.<domain-name>                     : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                     : Failed
         : Cannot resolve the IP address for airportdc1.<domain-name>.
ADDNS    : DNS lookup of DC xxxx.<domain-name>                     : Pass
GCPORT   : Port scan of GC xxxx.<domain-name>                      : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                  : Pass
GCPORT   : Port scan of GC xxxx.<domain-name>                   : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                    : Pass
GCPORT   : Port scan of GC xxxx.<domain-name>                     : Warning
         : One or more ports failed to respond correctly. Either:
         :   a) the GC is offline
         :   b) a firewall is preventing access to a port
         : The following is a list of failed ports:
         :    gc(3268)/tcp - refused
ADDNS    : DNS lookup of DC xxxx.<domain-name>                       : Pass
GCPORT   : Port scan of GC xxxx.<domain-name>                        : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                       : Pass
GCPORT   : Port scan of GC xxxx.<domain-name>                        : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                          : Pass
GCPORT   : Port scan of GC xxxx<domain-name>                           : Pass
ADDNS    : DNS lookup of DC xxxx.<domain-name>                   : Pass
GCPORT   : Port scan of GC xxxx.<domain-name>                    : Pass
ADGC     : Check Global Catalog servers                                : Pass
DCUP     : Check for operational DCs in <domain-name>                    : Pass
SITEUP   : Check DCs for <domain-name>in our site                        : Pass
DNSSYM   : Check DNS server symmetry                                   : Pass
ADSITE   : Check that this machine's subnet is in a site known by AD   : Pass
GSITE    : See if we think this is the correct site                    : Pass
TIME     : Check clock synchronization                                 : Pass
2 serious issues were encountered during check. These must be fixed before proceeding
2 warnings were encountered during check. We recommend checking these before proceeding
main-acs-01/admin#
Has any one face this issue before and appreciate if someone can advise how to fix this.

This was a known issue with ACS 5.3 however, we got this fixed in ACS 5.3 patch 7 and ACS 5.4
Since you're running ACS 5.4, it should not trigger.
CSCtx53223    After upgrade ACS 5.3 fail to join AD domain - missing Centrify license
Symptom:
After upgrading from 5.2 to 5.3, ACS fails to join the domain. AD connection worked for a few days, until the services were restarted. After that ACS fails to join AD with the following error message in ACSADAgent.log:
Jan 20 02:36:32 CBR1BACS01 adjoin[6814]: DEBUG cli.adjoin Join to zone is only permitted with a licensed copy of DirectControl. Get a license or learn more about Centrify Suite at http://www.centrify.com/express
Jan 20 02:36:32 CBR1BACS01 adjoin[6814]: DEBUG cli.adjoin Without a license, you may connect to a domain through Auto Zone by specifying adjoin -w Test.Test
Conditions:
Upgrade from 5.2 to 5.3. Restart the services later on.
Workaround:
Backup the ACS db and re-image the box to 5.3
How did you upgrade to ACS 5.4
1.] Upgraded from 5.3 to 5.4 using upgrade package.
2.] reianged it with ACS 5.4 ISO and restored the ACS 5.3 database.
I would suggest you to open a TAC case on this. Most likely you need reimage the server and restore the database if you had gone through with option 1.]
~BR
Jatin Katyal
**Do rate helpful posts**

Similar Messages

  • I suffering a strange issue ACS 4.2

    Hi Guys
    I suffering a strange issue , I have two group users (wireless user , VPN users),
    I created a NAR To restrict users,, created two group NAR (network access restriction ) wirless group and vpn group
    I attached wireless NAR group to wireless group user , and attached VPN NAR group to VPN group users ,
    Supposed Wireless users only have access to wireless ,and VPN users just have access to connect VPN and they don’t have access wireless .
    The issue VPN user can access wireless!!!!!
    Notice I used ACS4.2 And Aruba controller
    Is this bug in ACS 4.2 or what ? please advice

    Hi,
    NAR are based on two radius attributes (calling-station-id = client information) (called-station-id = network device information).
    The issue is based on the VPN NAR that you have configured.
    However let me explain why this works for the WLAN users, you configured an IP based rule (dont know if this was intentional but it works), in a way that if a client authenticates with the calling-station-id from the VPN server (ip address is the format for calling-station-id), that it must match the called-station-id that belongs in the "NDG-WLAN" which fails. I noticed that you do not have a DNIS condition configured, the ACS is designed to failover to this rule for non IP based NAR filters. For wireless dot1x authentication (calling-station-id is the mac address of the client), there is no CLI/DNIS based rule enabled so that is why the wireless requests are permitted.
    When the VPN users connect to wireless an hit the VPN NAR, the calling-station-id is a mac address format, and with no CLI/DNIS rule configured you allow them access.
    In the VPN NAR, you should create a DNIS based rule which denies access from the NDG:WLAN and wildcard the dnis field, and that will fix your issue.
    Here is some reference material:
    http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/SPC.html#wp766301
    "IP-based NAR filters work only if ACS receives the Radius Calling-Station-Id  (31) attribute. The Calling-Station-Id (31) must contain a valid IP  address. If it does not, it will fall over to DNIS rules."
    Thanks,
    Tarik Admani
    *Please rate helpful posts*

  • Join Query Issue

    Hi,
          I have issue in the following query when selecting SPART . If spart is selected , the results are not correct. Is there anything i am missing in the query.
      SELECT  amatnr aersda alaeda aprdha aspart bmaktx cprodh cvkorg cvtweg  cmvgr1  cmvgr2  cmvgr3   cmvgr4  cmvgr5
        INTO  CORRESPONDING FIELDS OF TABLE tbl_initdata
        FROM  ( ( mara AS a
                  INNER JOIN makt AS b ON   amatnr = bmatnr    )
                  INNer JOIN mvke AS c ON   amatnr = cmatnr     )
        WHERE a~mtart EQ p_mtart AND
              a~ersda IN s_ersda AND
              a~laeda IN s_laeda AND
              a~lvorm EQ p_lvorm AND
              a~spart IN s_spart AND
              c~vkorg IN s_vkorg AND
              c~vtweg IN s_vtweg AND
              c~lvorm EQ p_plvor.

    Dear Friends,
               The query is not working when we use SELECT-OPTIONS for SPART. When using paramater its working fine.. For your more analysis, i am giving the Selection screen declarations and my Test Procedure.
    SELECTION-SCREEN BEGIN OF BLOCK b1 WITH FRAME TITLE text-h01.
    PARAMETERS:     p_mtart   TYPE mtart MEMORY ID mta OBLIGATORY
                                           DEFAULT 'FERT'.               "Material Type
    SELECT-OPTIONS: s_ersda   FOR  mara-ersda   ,         "Created on
                    s_laeda   FOR  mara-laeda   ,         "Changed on
                    s_vkorg   FOR  mvke-vkorg,            "Sales Organization
                    s_vtweg   FOR  mvke-vtweg,            "Distribution Channel
                    s_spart   for  mara-spart.             "Division
    SELECTION-SCREEN END OF BLOCK b1.
    SELECTION-SCREEN BEGIN OF BLOCK b2 WITH FRAME TITLE text-h02.
    PARAMETERS: p_lvorm AS CHECKBOX DEFAULT space,       "Marked for Deletion at Client Level
                p_plvor AS CHECKBOX DEFAULT space.       "Marked for Deletion at Plant Level
    SELECTION-SCREEN END OF BLOCK b2.
    HERE is the Select Query,
      SELECT amatnr aersda alaeda aprdha aspart bmaktx cprodh cvkorg cvtweg cmvgr1 cmvgr2 cmvgr3 cmvgr4 cmvgr5
    INTO CORRESPONDING FIELDS OF TABLE tbl_initdata
    FROM  mara AS a
    INNER JOIN makt AS b ON  ( amatnr = bmatnr )
    INNer JOIN mvke AS c ON  ( amatnr = cmatnr )
    WHERE a~mtart EQ p_mtart AND
    a~ersda IN s_ersda AND
    a~laeda IN s_laeda AND
    a~lvorm EQ p_lvorm AND
    a~spart IN s_spart AND
    c~vkorg IN s_vkorg AND
    c~vtweg IN s_vtweg AND
    c~lvorm EQ p_plvor.
    TEST PROCEDURE ...
    I am just selecting Material Type 'FERT', VKORG ,VTWEG and SPART.... Its returning a fixed value of 20 entries even when there are 1000+ entries in the Database.
    Please put this code in your SAP environment and help me out...You can see this strange issue!!!
    BTW, Thanks a lot for all SAP folks who are helping me out.

  • Strange issue with WEBI schedule Report

    Hi All,
    I have a strange issue with schedule WEBI reports, a schedule report runs for Hours , i reschedule it again by deleting the instance and the schedule report never got succeed even after running for hours.
    Any idea???
    regards

    Hi Manoj,
    1. Try to put some filters in the report and then run the report. if it takes less time, then probably your query is fetching very    large data.
    2. MDX query error may be the reason , this error come when a query runs endless, please try running the query 2-3 times, or when load on server is less.
    Hope this will help,
    Anamika.

  • Files transferred to external HD end up in trash - very strange issue

    Hi,
    I seem to be having a very strange issue, hopefully somebody can help or has seen this before.
    Hardware: MacBook Air, Western Digital Passport external HD, 250gb, formatted NTFS.
    Software: OSX 10.7 Lion, Paragon (allows me to write to an NTFS formatted HD)
    Issue Summary: I copy something to the external HD; I empty trash; the file I copied is deleted from the external HD. It doesn't happen every time.
    I do also seem to have a persistent folder in trash called "WD Sync Data" that won't go away unless I re-delete it as it's also in the root of the drive. Not sure if this is related somehow.
    Recently I copied 3 video files inside a folder to the HD, then disconnected the HD. When I reconnected it a while later and noticed that inside the "WD Sync Data" folder in trash were the 3 files I'd copied. I then looked inside the same folder on the root of the drive and the files were there, instead of inside the folder that I'd copied to the drive, which had vanished. If I hadn't noticed and had emptied the trash, those files would've been deleted.
    It's definitely happened more than once; last time I actually deleted the files from my computer after copying, then emptied trash, and they were gone from the external HD also.
    I've only found one person who seemed to be experiencing a similar problem back in 2010. It sounds similar though it could've been user error: http://www.mac-forums.com/forums/apple-notebooks/188224-weird-external-hard-driv e-trash-problem-help-please.html
    Has anyone experienced this or have any suggestions?

    Quick update: I ran a verify then a repair in Disk Utility as there were a couple of errors. Hopefully this has solved the issue, however it'd still be interesting to know if anyone's come across this before and what caused it?

  • Oracle Identity Manager 9.1.0.2 & WebLogic Strange Issue

    Hello,
    I am running OIM 9.1.0.2 (new installation) and WebLogic 10.3.3 in a clustered environment. I am having a strange issue where the resolution is eluding me.
    This install is running on Windows 2008 x64 Standard and using the x64 JRockit Java.
    What's happening is when I configure the managed server to run as a windows service, OIM isn't detected on the server. I can bring up xlWebApp but an unable to log into that or the Design Console. When launching the Diagnostic Dashboard it statest that OIM isn't installed.
    If I stop the service and log into WebLogic and start the managed server from within the Admin Console in WebLogic, everything works just fine.
    Any thoughts on how to troubleshoot this and ultimately resolve this? The service correct startes the managed server as I can watch it start up in the admin console but when it starts that way, OIM isn't detected. Very odd.
    Thanks,
    Andrew

    Oracle confirmed with us that it is certified for 10.3.3 though it may not be published yet.
    At any rate I figured out the problem today. The script I used to create the service was missing the JAVA_OPTIONS section from the xlStartManagedServer.cmd file. Once I added that and re-created the service, all is well.
    Thanks

  • Windows Vista and BPS0 - Strange issue

    I just got a new HP Pavilion laptop with Vista and I have a strange issue:
    All transactions work (SE80, RSA1, ...) except BPS0. The moment I enter TCode BPS0, I get completely logged out (all sessions). No error messages, no dumps. It just logs me out silently.
    Is this happening only to me?
    I use Windows Vista Home Premium edition and AMD Turion processor 64x2.
    Any suggestions appreciated.
    Thanks

    i too recently bought hp pavillion and my problem is i cant able to logon it gives me error of 10054, connection broken, can you tell me which things restrict me to log on. any settings are there to be performed. do mail me, i have been trying from 2 week my id is [email protected]

  • Strange issue with RAM upgrade: It works but it doesn't! Please help.

    Hello Everyone,
    I have a very strange issue with my iMac since upgrading my RAM from 4 to 12 gig. When I first installed the new RAM it booted up and ran great. The next time I went to boot the iMac up it swtiched on but didn't get as far as the first white boot up screen. I tried turning it off and on a few times using the power on/off button but still no success. I decided to remove the RAM and reseat it. The computer then booted up again fine. Here's the problem though: when I went to switch my iMac on the next day it wouldn't boot up. Again, I took the RAM out and put it back in and the iMac booted up fine. I've checked the status of the RAM in the system profiler and it reports that everything is OK. So, I'm at a loss. Obviously, I don't want to go through this process every time I want to start up my Mac. Any ideas/solutions would be very gratefully received.
    Many thanks in advance.

    I completely agree with you. It will be one of the 3 issues you outline. The machine was bought brand new and has never given me a problem. It is just the introduction of the new RAM that has started a problem. However, I did just risk a restart and it booted up fine. I don't know if a restart is any different to shutting down and then pressing the on/off button to start the computer. Maybe my last reseating has done the trick or maybe my thinking is flawed because restarting involves a different process to booting up by pressing the on/off button. I don't know.
    In the part of the world I'm sitting in it's night time now so I will leave the diagnostics running and check the results in the morning. I hope the issue is now resolved anyway. This sort of thing takes me back to my dark PC days although in this case I know it's probably not the Mac's fault.
    Thanks again. Very much appreciated.

  • Strange issue with rights of account, used by SSIS (Foreach Loop Container does not return file names without Admin rights on server)

    Hello everyone.
    Faced very strange issue with account, which is used to run SSIS package.
    The specific package uses Foreach Loop Container to retrieve file names within the specified folder, and put them into Import file task.
    The package is set up to run under specific service account. This service account is given all permissions (Full control) to the folder where source files reside.
    So the issue is: SSIS package fails to execute this task (Foreach Loop Container and then Import), and shows that no files are found in the directory (although files ARE there).
    Once we're adding the service account into local Administrators group on the SQL Server, it works! Removing - does not work again. We cannot leave the service account as SQL server's admin as it's prohibited by our IT policies, and is just a bad practice.
    Any ideas, please? 
    MCP

    Here's the real log output:
    Date 16.04.2014 12:47:09
    Log Job History (RU-BW: Update)
    Step ID 1
    Server Server
    Job Name RU-BW: Update
    Step Name bw_import_cust_master_data
    Duration 00:00:02
    Sql Severity 0
    Sql Message ID 0
    Operator Emailed
    Operator Net sent
    Operator Paged
    Retries Attempted 0
    Message
    Executed as user: service_account Microsoft (R) SQL Server Execute Package Utility  Version 10.50.4286.0 for 64-bit  Copyright (C) Microsoft Corporation 2010. All rights reserved.    Started:  12:47:09  Error: 2014-04-16 12:47:11.45
        Code: 0xC0202070     Source: bw_import_cust_master_data Connection manager "Input"     Description: The file name property is not valid. The file name is a device or contains invalid characters.  End Error  Error:
    2014-04-16 12:47:11.47     Code: 0xC0202070     Source: bw_import_cust_master_data Connection manager "Input"     Description: The file name property is not valid. The file name is a device or contains invalid characters.  End
    Error  Error: 2014-04-16 12:47:11.48     Code: 0xC0202070     Source: bw_import_cust_master_data Connection manager "Input"     Description: The file name property is not valid. The file name is a device or contains invalid
    characters.  End Error  Error: 2014-04-16 12:47:11.48     Code: 0xC020207E     Source: Import file Flat File Source [1]     Description: The file name is not valid. The file name is a device or contains invalid characters.
     End Error  Error: 2014-04-16 12:47:11.48     Code: 0xC004701A     Source: Import file SSIS.Pipeline     Description: component "Flat File Source" (1) failed the pre-execute phase and returned error code 0xC020207E.
     End Error  DTExec: The package execution returned DTSER_FAILURE (1).  Started:  12:47:09  Finished: 12:47:11  Elapsed:  2.324 seconds.  The package execution failed.  The step failed.
    MCP

  • Strange issue in custom Success/Failure captions

    Hi,
    I have a strange issue in my custom Success/Failure caption. If I use 'S' letter in my customized caption .bmp file, it is not showing properly in the captivate. Attached file is for your reference. I tried converting text into image in photoshop, still it shows the same thing. Any thoughts??
    Thanks in Advance,
    -Ajay

    OK.  That's what I thought.
    So what I think is going on here is due to the way Captivate assembles text captions that can stretch to any size based on the component images.  I think your corner image that contains the text is being stretched right at the point where the S character is located on the end of Congratulations.  Captivate is achieving the resizable text caption by repeating the last few pixels of each background image.
    If you want to test my theory, just make your Congratulations text slightly shorter (use a condensed font or make the font size smaller) and I think your issue will go away.

  • Strange issue in Report Builder

    Hi All,
    I am facing a strange issue in Report Builder.
    I am having a report which is currently in production. when i am opening that report and just saving it without making any changes, then also the size of the report is reducing from 238 to 204 kb.
    When i am executing this report in production then it is giving me the error "Invalid Body size"
    Please hlep me or else have to ask God to save me.
    Thanks
    Aryan

    Hi Hussien,
    I tried thart solution but it not worked. i put some debug statement in Before Parameter form, after Parameter form, before report triggers. When i am running that report i am getting the debug statement of Before and After Parameter triggers but it is failing somewhere in Before Report Trigger.
    I removed everything from Before Report Trigger and still the result is same "Invalid Body Size".
    Please Hussien give me a some pointer which stage is processed between After Parameter Form trigger and Before Report Trigger.
    Thanks
    Aryan

  • Strange issue with external monitor, only working when external speakers plugged in (using Thunderbolt to VGA adaptor)

    Hey – I am having a very strange issue with my external monitor; where it only works if my external speakers are plugged in and connected.
    I am using a late 2011 Macbook pro, running Mavericks 10.9.4, along with an MBox 2 (USB Audio Interface), and two powered speakers (KRK Rokit 5). This setup has had no issues. I have just acquired an external monitor (Benq T2200HD), which I am using with a thunderbolt to VGA adaptor (a cheap Chinese knockoff adaptor).
    To start - I plugged the monitor in with the thunderbolt adaptor, and it powers up and works fine. However, there is a nasty buzz coming from the speakers. I did some research and it looks like a simple ground loop issue. I did a bit of troubleshooting, and this is where things get weird.
    What I found is - If I unplug the MBox, the monitor loses signal from the computer (displaying ‘No Signal Detected!’). Further, if I keep the MBox plugged in, however unplug both the cables from the MBox to the speakers, the monitor loses signal. It doesn’t matter if the speakers are turned off, however they need to be plugged in (or the monitor loses signal). Weirder still, I can unplug the MBox, however the monitor will work if I plug in the speakers through my macs headphone jack.
    Simply put, the monitor only works if there is a direct connection between the computer, the speakers, and the power source.  What is going on here? Is the monitor grounding through the computer port, to the speakers (I don’t know how this works, is this possible?). Could it somehow be the cheap VGA adaptor I am using?
    Some other information:
    - Everything is plugged into the same multi-box for power. I have tried plugging things into separate sources, and the result is the same.
    - If I unplug the thunderbolt adaptor, then the speaker noise disappears straight away.
    - The ground noise doesn’t appear in my headphones, which are plugged into the MBox.
    Any information would be great – am I missing something here, or is this genuinely weird?

    Well, I went back into Best Buy to test on 3 other laptops (2 Asus, and their floor model for this Sony). It seems to be doing the same problem so at least I was able to rule out broken hardware issue on my particular laptop.
    Here's what I did to test:
    Since I couldn't really install Adobe Premiere on their machines, I used the DVIO software (http://www.carr-engineering.com/dvio.htm) and a 5 min clip I captured.  I transferred onto their machines, hooked up my Sony D8, and attempted to play the video.  It would play for 15 seconds and then stop and jitter with a loud noise (like it does on my laptop).  I even tried changing each machine's firewire driver to the legacy one and same results.  I pulled a brand new 4 pin to 4 pin firewire cable off their shelf and still the same problem.
    I think I've nailed it down to Win7x64 bit Home Edition not playing nice with Firewire driver.  Very annoying.  I can't find any concrete evidence of this from other users on any of the forums that have my particular problem, but from my own testing, it's all I can conclude.
    I have 2 other things I can try:
    1.  Opening the laptop and looking at the firewire to maybe find appropriate driver (ugh, I don't want to have to open this thing up).
    2.  Upgrading to Win7x64bit Pro and possibly testing with XP on the new MS Virtual PC (http://www.microsoft.com/windows/virtual-pc/).  I can't do it with my Home edition apparantly.
    Who needs to view video on an external TV anyways....sheeesh...(scarcasm).
    Tim

  • I am having strange issue with my apple tv...i set up pictures to scroll through to the tv using home sharing.  Now album covers are interspersed with my pictures.  I have been using apple tv for a while and never had this happen before

    I am having strange issue with my apple tv...i set up pictures to scroll through to the tv using home sharing.  Now album covers are interspersed with my pictures.  I have been using apple tv for a while and never had this happen before

    Are you watching this content though iCloud or though from iTunes on your local computer?  If it is from iCloud have you tried downloading the content to iTunes and watching it on ATV from that source to see if it still happens?  This is geerally a much more reliable way to view the content.  Easer to fast forward and rewind too.
    - I have a stable internet connection
    Clearlly you don't
    >(Ive tested on other devices)
    Which does not tell you anything about the specific connnection from ATV to iCloud.
    >I am able to stream Netflix problem free from my AppleTV without so much as a hicup
    Again which does not tell you anything about the specific connnection from ATV to iCloud.
    >- I am able to download the episodes to my phone, ipad, and computer without any issues
    Again which does not tell you anything about the specific connnection from ATV to iCloud.  It does remove your ISP throattly traffice as a possible cause though.  So that is good.
    Have you checked your wireless rounter?  Tried doing the factory restor on it?  Upgrading it's firmware?  Is it and or ATV getting extreamly hot when this problme happens?

  • Huawei E220 strange issue running 10.6.2

    Hi, I'm testing the Huawei E220 with a brand new Macbook Air running 10.6.2.
    My provider is Vodafone IT.
    I have a very strange Issue:
    If I start the connection the Macbook Air suddenly shuts down a few seconds after the connection has been established. If I leave the modem connected to the usb port without activating a connection nothing happens.
    Has anyone had this same problem??
    This mac works perfectly with any other HSPDA usb modem.
    Vodafone posted a new software for mac (Vodafone Mobile Broadband 3.04.10.00). This link can be useful (not only for Italy) because it is constantly updated:
    http://www.business.vodafone.com/site/bus/public/enuk/support/10productsupport/laptop_connectivity/40_software/software/10_latest/pmac.jsp

    my friends 13" mbp is also having trackpad problems. I plugged in an old usb trackball and that seems to to at least get me so I can run a hardware test off the applications dvd.

  • A very very strange issue on BlazeDS Deserializing

    Hi all,
    I run into a very very strange issue on BlazeDS Deserializing. Is there any hint or idea?  Thanks a lot!
    Scenario 1:
    Both the browser(firefox or IE) and the midtier (BlazeDS ,java) are on the same machine.
    Actual result:
    Everything works fine.  All the properties in the Flex Object could be mapped to the Java Class
    Scenario 2:
    The browser(firefox or IE) and the midtier (BlazeDS ,java) are on the different machine.
    Actual result:
    Sometimes it works fine.
    And most of the time it does not work fine. Only the data in List is mapped correctly. All the values of simple data type such as int are mapped to 0 .
    Let me simplify the problem.
    The objects of Class B is always stored in the ArrayCollection  assocItems of Class A
    Flex side:
    public class A {
    public var id: int;
    public var  name: String;
    public var assocItems: ArrayCollection=new ArrayCollection();
    public class B {
    public var id: int;
    public var  assocItems : ArrayCollection=new ArrayCollection();
    The id , name in Flex Class A and assocItems in Class B could be  deserialize to correct value .  But the id of Class B is always mapped to 0. This is not correct.
    The log level of BlazeDS is configured to Debug. From the log I can see that  each value is passed from Flex side to Java server side correctly.
    [BlazeDS][INFO] Channel endpoint my-amf received request.
    [BlazeDS][DEBUG] Deserializing AMF/HTTP request
    Version: 3
    (Message #0 targetURI=null, responseURI=/18)
    (Array #0)
    [0] = (Typed Object #0 'flex.messaging.messages.RemotingMessage')
    However, the Java object does not get the correct value of B.id.
    In conclusion,
    1. It’s an issue with only default types
    2. It does not occur every time
    3. It does not occur when the browser(firefox or IE) and the midtier (BlazeDS ,java) are on the same machine
    Have you ever run into the similar problems? And what’s your solution?

    I checked, when I hard-code the constant in linq, the generated sql is like this:
    SELECT "Extent1"."AA" AS "AA"
    FROM (SELECT "TBL"."AA" AS "AA"
    FROM "USERNAME"."TBL" "TBL") "Extent1"
    WHERE ('1062303212007000121' = "Extent1"."AA")
    if I pass a variable to the query with same value, the sql is like this:
    SELECT "Extent1"."AA" AS "AA"
    FROM (SELECT "TBL"."AA" AS "AA"
    FROM "USERNAME"."TBL" "TBL") "Extent1"
    WHERE ("Extent1"."AA" = '1062303212007000121' /* @p__linq__0 */) (@p__linq__0 is passed as parameter)
    The only difference is a paramter. I can't figure out why there is such a impact on performance.

Maybe you are looking for

  • REG: PROCESS MAPPING

    Hi All,               I have scenario, in stock transfers from plant to depot, 1) Depot send the indent to plant in excel sheets 2) Executive at plant makes the sto( in SAP  for available products and remaining will put in pending orders( makes in ex

  • Web Gallery-Surprising Differences between Safari and Firefox

    I discovered some surprising differences using Web Gallery in Safari vs. Firefox: 1. When you first view an album the gallery, the thumbnail photos take quite a bit longer to be visible in Safari than in Firefox. 2. When rolling the mouse over the Su

  • 5.1 via bluetooh

    I got a Bluetooth adapter hooked up to my Harman Kardon AVR 130 Receiver, to play Music i connect my MacBook Pro to the Bluetooh adapter. Is it possible (since the Receiver plays 5.1 sound, and i have 5.1 speakers) to play my iTunes music via bluetoo

  • How do I clear Dreamweaver CS6 image cache (on Mac)?

    Hi, I have updated a remote image (absolute link) but it doesn't update in DW (CS6). How do I clear the image cache?

  • How do I see which computers are authorized?

    I am trying to find out why ITunes says that I have 3 computers listed when we only have 2 computers but I can't seem to see which individual computers are part of my account? Any thoughts? Thanks.