Acs and Dynamic vlan assignment problem

Hi all,
I'm unable to dinamically pass the Radius attribute , about assigned vlan, to 802.1x clients.
I'm sure that everything is well configured but the only way to do it is configuring these attributes directly on user or group properties.
When i try to pass these attributes by appliction of a Shared RAC (acs 4.2) or NAP (ACS 5.0) the only message that i can find on the switch, where the vlan has to be configured, is:
dot1x-ev:Received VLAN is No Vlan
dot1x-ev:Received VLAN Id -1
The user is still authenticated successfully ( and all the profiles correctly assigned) but remain in the vlan statically configured on the interface.
The logic is working, but transmission do not.
Is this a bug ?

test the authentication again.If is still fails, set the logging to full on the ACS server using:
http://www.cisco.com/en/US/products/sw/secursw/ps2086/products_tech_note09186a00800afec1.shtml#setting_acs
Also Check if you are running another RADIUS product on the same server as the ACS services and the same decryption was being used.Reset shared key on switch and radius server.

Similar Messages

802.1X for wired environments using Radius/ACS for Dynamic Vlan Assignment

Currently Being Moderated
802.1X for wired environments using Radius/ACS for Dynamic Vlan Assignment
Could someone please provide me with a simplest set of configuration steps to fire up Radius in ACS and 802.1X for dynamic vlan assignment. The objective is to roll out NAC L2 OOB using the 802.1X method for dymamic vlan assignments.
If possible show:
1. ACS/Radius Configurations.
2. End User Switch Configurations
Variables:
Switch A
MAC Address aaaa.bbbb.cccc     Vlan 10
            bbbb.cccc.dddd     Vlan 20
Also, if someone posts the Pros and Cons of using Radius/ACS/802.1X for Dynamic Vlan Assignments.
Other technology sets that can be used for Dynamic Vlan assignment EXCEPT from deprecated/obsolete VMPS.
Thanks in advance. .

Hi Guys,
    Hmmm, well if your just looking for Mac based authentication the good news is that is very easy. Just set create your Radius server, ACS, FreeRadius, Steelbelted radius etc. Then create user with the name of the Mac address, in other words if the mac address is 0012.0021.1122 the the name would be 001200211122 and the password would be the mac address. Then you set the vlan and tunnel stuff, like so tunnel-Type would be vlan, Tunnel-medium would be 802 and Tunnel-Private-Group-ID is the name of the vlan(not the vlan number)
   So for the Cisco ACS 4.x you would create a user as specified above, fill in all the password boxes with MAC address, I believe the mac has to be all lower case in the name and the password. Then check the Separate(Chap/MS-Chap/ARAP) box. Then you pick the group the machine belongs to, the group is the part that defines what vlan it is on.
   Before you create the user, create the group with info I wrote above and in addition specify the Service-Type as Authenticate Only.
    Freeradius is a bit harder to configure the specifics and I am just now testing a freeradius server so I do not know the process for Machine authentication.
    If, however, you are trying to authenticate a user that gets a bit trickier and is not so straight forward.

HREAP and Dynamic VLAN assignment (MS NPS)

Hi All
Just a quick rundown of what I am trying to achieve.
We have a Cisco 5508 WLC (running AIR-CT5500-K9-7-0-116-0.aes). At the moment the WLC is controlling only 1 AP (Cisco 1142N LWAP). I want this AP to be placed at a remote site, and users that authenticate via the RADIUS (MS Windows 2008 NPS) server must be assigned their respective VLANs based on the Active Directory groups they belong to (staff, student, or guest).
The AP and dynamic VLAN assignment works 100% if the AP is in local mode. Authentication works, and dynamic VLAN assignment works. As soon as you change the AP to HREAP mode, dynamic VLAN assignment stops working, and the client gets assigned an IP of whatever VLAN is assigned to the SSID under the HREAP tab. Allow AAA Override is enabled on the main SSID that I am broadcasting.
I have read in some of the discussions that HREAP does not support dynamic VLAN assignment, but I haven't seen why this is not supported. Is this true with the latest version of WLC software as well? I cannot see why local traffic destined for a local resource must be sent via a WAN link to the controller, and then back over the WAN link again. This seems very inefficient.
Is there anybody that can confirm if this is in fact an HREAP limitation, and why (if so) it is a limitation, please? Any info would be much appreciated.
Regards
Connie

Do you perhaps know if there are plans for this limitation being addressed in the near future?
We are looking to deploy wireless from end-to-end in all 6 of our sites, and you biggest competitor was penalized because they do not support this feature. It seems we're going to have to apply the same penalty in this respect to Cisco as well.
Thanks for the feedback, though!
Regards
Connie

5508 and dynamic vlan assignement

Hello,
I'm trying to setup a 5508 to work with dynamic vlan assignement using the same SSID.
I've followed everyting in this document http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
but it doesn't work, every client independent of the RADIUS group is assigned to the same VLAN.
The only difference I have with that document is the [081] Tunnel-Private-Group-ID for which I use a string (nessesary for the LAN switches which use the same RADIUS) instead of a number.
What I see when sniffing the RADIUS traffic, every option is sent correctly to the WLC, from the WLC side and using the debug aaa events enable option I see nothing interesting.
Any ideas?
Thanks
George

A bit more debugging gave me this:
*Oct 15 09:31:28.491: xx:xx:xx:xx:xx:xx Received Tunnel-Group-ID Attribute -- ignoring AES Interface-Name '200' for STA xx:xx:xx:xx:xx:xx.
*Oct 15 09:31:28.491: xx:xx:xx:xx:xx:xx Tunnel-Type 16777229 should be 13 for STA xx:xx:xx:xx:xx:xx
(xx:xx:xx:xx:xx:xx is the client mac address)
It seems that:
1. WLC ignores the [14179\005] Aire-Interface-Name parameter regardless of what the value is (I have tried the vlan number, the interface name etc)
2. the second error is that the tunnel-type 16777229 should be 13. The tunnel-type has the value VLAN as required according to the Cisco document and in general for this to work. Funny thing is that RFC2868 doesn't define a value of 13 but RFC3580 define VLAN as value 13 so again I've set the correct value.
So I don't really know what to do now. I guess I have to open a TAC ticket.

Dynamic VLAN assignment with WLC and ACS for

Currently, using our autonomous APs and ACS, our users get separate VLANs per building based on their security level (students or staff). Basically, the student VLAN in one building is different from that of the student VLANs in other buildings on campus. Currently, we do this by filling the Tunnel-Private-Group-ID IETF RADIUS attribute with the VLAN name. This all works because each individual AP can map VLAN names to different VLANs like this:
dot11 vlan-name STUDENT vlan 2903
dot11 vlan-name FACSTAF vlan 2905
As we are working on our WiSM deployment, we see that the document below shows how to do the dynamic VLAN assignment on our WLAN controllers:
http://www.cisco.com/en/US/customer/products/sw/secursw/ps2086/products_configuration_example09186a00808c9bd1.shtml
However, we haven't figured out if it's possible to still provide our users with different VLANs for each building they're in.
With the instructions above, it looks like ACS uses a Cisco RADIUS Attribute to indicate the Air-Interface-Name, mapping an ACS/AD group to a single WLC interface which can only have one VLAN/subnet associated with it.
Does anybody know if what we're trying to accomplish is possible, or if we're really stuck with only one VLAN/subnet per mapped ACS group?

We only have the one WiSM for all of campus, so it's handling everything. This Cisco docs do indicate how to put differnet users in different Vlans, but we don't currently see a way to also put them in different subnets per building.
This being the case, any suggestions on how best to handle more than a Class C subnet's worth of users? Should we just subnet larger than Class C, or is there a more elegant way of handling this?

802.1x dynamic vlan assignment using ACS 4.2

Hi
we have 10 switches 2960 configured with 802.1x authentication against ACS server 4.2.
we have 2 vlans configured on the switches for administrator and endusers. the end user vlan id is 10 and the administartor vlan is is 100.
we need to apply the following scenario, if the enduser PC - that is connected to vlan 10 - has an issue and the administrator will login to the PC with the administrator account to fix that issue, the switch should dynamically reconfigure the port with the administrator vlan ( 100 ) .
is the above scenario doable using dot1x with the ACS server?
waiting your replies
Mohamed

Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each
user should be able to connect and roam around between any building.
when ever a user is connecting his laptop to any floor, he should be
made part of that respective vlan. It is not requred to have the same
IP rage to be allocated, but the dynamic VLAN should be based on the
switch port location.
Can
I configure ACS in such a way that, the ACS will allocate dynamic VLAN
for every 802.1x authentication based on the Network Device Group.
Please refer the attached diagram
Hi,
Check out the below link for your requirement for dynamic vlan assignement using ACS
http://www.ciscosystems.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

802.1x Dynamic Vlan assignment using ACS

Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each user should be able to connect and roam around between any building. when ever a user is connecting his laptop to any floor, he should be made part of that respective vlan. It is not requred to have the same IP rage to be allocated, but the dynamic VLAN should be based on the switch port location.
Can I configure ACS in such a way that, the ACS will allocate dynamic VLAN for every 802.1x authentication based on the Network Device Group. Please refer the attached diagram

Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each
user should be able to connect and roam around between any building.
when ever a user is connecting his laptop to any floor, he should be
made part of that respective vlan. It is not requred to have the same
IP rage to be allocated, but the dynamic VLAN should be based on the
switch port location.
Can
I configure ACS in such a way that, the ACS will allocate dynamic VLAN
for every 802.1x authentication based on the Network Device Group.
Please refer the attached diagram
Hi,
Check out the below link for your requirement for dynamic vlan assignement using ACS
http://www.ciscosystems.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points

Hi Guys,
I would like to go for "Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points 1300". I want the AP to broadcast only 1 SSID. The client find the SSID ->put in his user credential->Raudius athentication->assign him to an specific vlan based on his groupship.
The problem here is that I don't have a AP controller but only configurable Aironet Access Points 1300. I can connect to the radius server, but I am not sure how to confirgure the AP's port, radio port, vlan and SSID.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
I go through some references:
3.5 RADIUS-Based VLAN Access Control
As discussed earlier, each SSID is mapped to a default VLAN-ID on the wired side. The IT administrator may wish to impose back end (such as RADIUS)-based VLAN access control using 802.1X or MAC address authentication mechanisms. For example, if the WLAN is set up such that all VLANs use 802.1X and similar encryption mechanisms for WLAN user access, then a user can "hop" from one VLAN to another by simply changing the SSID and successfully authenticating to the access point (using 802.1X). This may not be preferred if the WLAN user is confined to a particular VLAN.
There are two different ways to implement RADIUS-based VLAN access control features:
1. RADIUS-based SSID access control: Upon successful 802.1X or MAC address authentication, the RADIUS server passes back the allowed SSID list for the WLAN user to the access point or bridge. If the user used an SSID on the allowed SSID list, then the user is allowed to associate to the WLAN. Otherwise, the user is disassociated from the access point or bridge.
2. RADIUS-based VLAN assignment: Upon successful 802.1X or MAC address authentication, the RADIUS server assigns the user to a predetermined VLAN-ID on the wired side. The SSID used for WLAN access doesn't matter because the user is always assigned to this predetermined VLAN-ID.
extract from: Wireless Virtual LAN Deployment Guide
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
==============================================================
Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
==============================================================
Controller: Wireless Domain Services Configuration
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c951f.shtml
Any help on this issue is appreicated.
Thanks.

I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps

Dynamic vlan assignment with 1242AG and IAS not working

I'm having trouble getting the dynamic vlan assignment to work on my 1242AG Cisco Aironet APs. I've seen multiple cases with a similar setup and configuration where it works just fine. I've tried everything I can think of. Any suggestions?
IAS and AD is running on Windows Server 2003
Everything works fine except the vlan assignment. Wireless clients successfully authenticate through IAS and Active Directory, but instead of being switched to the appropriate vlan the client stays in whichever vlan/ssid it originally connected to.
PEAP is the authentication method, using MS-CHAP v2. Naturally I have the attributes in the policy set appropriately, ie:
Tunnel-Medium-Type > 802
Tunnel-Pvt-Group-ID > vlanid
Tunnel-Type > VLAN
On the AP:
Cisco 1242AG, C1240 Software (C1240-K9W7-M), Version 12.4(3g)JA, RELEASE SOFTWARE (fc2)
I've attached the config for the AP, which shows that I have two vlans/SSIDs set to cipher, aes, network eap, wpa, etc. I noticed that if the
Tunnel-Pvt-Group-ID attribute is set to a vlan id that doesn't exist on the AP then the AP makes an event log saying so.

Good! Well to answer your questions, IAS is sending numbers, i.e. Tunnel-Pvt-Group-ID > 129
I did view the debug from an AP which showed the Tunnel attributes being recieved from the radius server (I'll have to wait until Monday to get a copy though).
I see I don't have that line "aaa authorization network default group rad_eap",
So I'll have give it a try, (maybe I can remote in so I don't have to wait until Monday).
Thanks,
Jason

Dynamic VLAN assignment and Layer 3 switching on 300 series

I have a SG300-28P switch. I just read in the Administration Guide that, when in Layer 3 mode, the switch doesn't support MAC-based VLAN or Dynamic VLAN Assignment.
So, in order to assign a client to a VLAN based on their MAC or based on the response of a RADIUS server, we have to disable layer 3 features. Without layer 3 switching, the switch is unable to act as a default gateway and forward packets between VLANs. As a result, the VLANs can't communicate in any way, or access the internet, unless a separate router is connected to every VLAN. Right?
I'm new to VLAN configuration and layer 3 switching so I wanted to check my understanding. Doesn't this limitation significantly reduce the usefulness of the DVA feature?
I may well be confused and missing something regarding how this is typically used..

Hello Glenn,
Your concept about packet forwarding is correct. With a layer 2 switch, there must be something directing traffic with multiple subnets for intervlan communication or something that provides an IP route to give the request a path back for the request.
The usefulness for the DVA feature, is not particularly limited to the switch as the switch will correctly assign the VLAN for you, as VS the L3 switch mode, you're dealing with IP addresses. In any scenario, you're going to require a router to get to the internet since the switch does not support NAT.
Additionally, if you're router does not support VLAN, the L3 switch feature would still be the solution since you should be able to make a static route pointing back to the switch to allow any subnet to traverse the single media. It would still beg the question, how to assign VLAN dynamically.
The answer, although (in my opinion is terrible) would be GVRP. But, this application would require ALL of your network cards to be GVRP Enable / Capable which most likely is not the scenario for you (or most anyone else for that matter).

WLC- dynamic Vlan assignment with Radius

Hello, we would like to use this feature in our company and because of that I am now testing it. But I found one problem.
I created one testing SSID and two Vlans on WLC. On ACS I use an IETF atributes (064,065,081) for my account and I am changing Vlan ID (081) during testing.
It works with LEAP but when I use PEAP-GTC (which we use commonly in our company) the ip address is not assigned properly (ip which was assigned before remains).
Could you please help me?

There is good document which explains how to configure Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller. This will help you. You will find the document at http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml

Dynamic VLAN Assignment + NPS

Hello,
I'm planning a deployment with the following:
5508 WLC running 7.0.222.0
NCS 1.0.2.29
50+ 3502i AP's
Windows 2008 R2 running NPS
EAP-TLS for authentication
The end goal is to have a single SSID and utilize NPS to dynamically assign VLAN's depending on role/group.
I've read several documents that use ACS to complete the dynamic VLAN assignment (inclduing http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml), however in this case ACS is not available.
My question basically is; do I need ACS to apply the VSA for Cisco Airespace, or can this be done solely with the following IETF attributes using Microsoft NPS and AAA override on the WLC?
[64] Tunnel-Type
[65] Tunnel-Medium-Type
[81] Tunnel-Pvt-Group-ID
Any advice would be greatly appreicated!
Thanks

Thanks Steve for your quick response.
I did everything as per your recommendation and it still doesnt work.
Do you mind providing me a remote assistance, do you have Skype?
Or your prefer that I provide you a set of logs, tell me which one and I will do so.
SSID:TT
@IP WLC: 172.20.252.70
NPS: 172.20.1.16
config rule NPS: service-Type: NAS Prompt
                         Tunnel-Type: VLAN
                         Tunnel-pvt-group-ID:10
                         Tunnel-Meduim-Type:802
log WLC:
*radiusTransportThread: Sep 19 12:32:47.841: ****Enter processIncomingMessages: response code=2
*radiusTransportThread: Sep 19 12:32:47.841: ****Enter processRadiusResponse: response code=2
*radiusTransportThread: Sep 19 12:32:47.841: 8c:70:5a:1c:8e:20 Access-Accept received from RADIUS server 172.20.1.16 for mobile 8c:70:5a:1c:8e:20 receiveId = 4
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.841: 8c:70:5a:1c:8e:20 Processing Access-Accept for mobile 8c:70:5a:1c:8e:20
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.842: 8c:70:5a:1c:8e:20 Applying new AAA override for station 8c:70:5a:1c:8e:20
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.842: 8c:70:5a:1c:8e:20 Override values for station 8c:70:5a:1c:8e:20
source: 4, valid bits: 0x200
qosLevel: -1, dscp: 0xffffffff, dot1pTag: 0xffffffff, sessionTimeout: -1
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.842: 8c:70:5a:1c:8e:20 Override values (cont..) dataAvgC: -1, rTAvgC: -1, dataBurstC: -1, rTimeBurstC: -1
vlanIfName: 'dy-data-ksb1', aclName: ''
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.842: 8c:70:5a:1c:8e:20 Inserting new RADIUS override into chain for station 8c:70:5a:1c:8e:20
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.843: 8c:70:5a:1c:8e:20 Override values for station 8c:70:5a:1c:8e:20
source: 4, valid bits: 0x200
qosLevel: -1, dscp: 0xffffffff, dot1pTag: 0xffffffff, sessionTimeout: -1
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.843: 8c:70:5a:1c:8e:20 Override values (cont..) dataAvgC: -1, rTAvgC: -1, dataBurstC: -1, rTimeBurstC: -1
vlanIfName: 'dy-data-ksb1', aclName: ''
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.843: 8c:70:5a:1c:8e:20 Applying override policy from source Override Summation:
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.843: 8c:70:5a:1c:8e:20 Override values for station 8c:70:5a:1c:8e:20
source: 256, valid bits: 0x200
qosLevel: -1, dscp: 0xffffffff, dot1pTag: 0xffffffff, sessionTimeout: -1
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.843: 8c:70:5a:1c:8e:20 Override values (cont..) dataAvgC: -1, rTAvgC: -1, dataBurstC: -1, rTimeBurstC: -1
vlanIfName: 'dy-data-ksb1', aclName: ''
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.843: 8c:70:5a:1c:8e:20 Setting re-auth timeout to 1800 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.844: 8c:70:5a:1c:8e:20 Station 8c:70:5a:1c:8e:20 setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.844: 8c:70:5a:1c:8e:20 Creating a PKC PMKID Cache entry for station 8c:70:5a:1c:8e:20 (RSN 2)
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.844: 8c:70:5a:1c:8e:20 Adding BSSID 00:1e:be:a7:bf:b6 to PMKID cache for station 8c:70:5a:1c:8e:20
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.844: New PMKID: (16)
*Dot1x_NW_MsgTask_0: Sep 19 12:32:47.844:      [0000] 80 36

RDP with 802.1x, machine and user auth and dynamic VLAN

Hi,
we have 802.1x implemented with machine and user auth. We also use dynamic VLAN assignment. Our client is AnyConnect 3.1. Operating system is Windows 7. With Windows XP, it works just fine.
When we try to connect to the 802.1x auth desktop with RDP (desktop is machine authenticated, no user is logged in), we are able to authenticate but as soon as VLAN and IP address changes according to user authentication profile, RDP session is terminated. It is not just disconnected but remote user is logged out and AnyConnect reverts 802.1x session back to machine VLAN. We cannot login with RDP and just loop between machine-user-machine authentication.
With this behavior the TermDD message (ID 56) can be seen in system log. Following the response
http://social.technet.microsoft.com/Forums/windows/en-US/b7814ec3-6a49-469c-8773-909c50415942/the-rdp-protocol-component-x224-detected-an-error-in-the-protocol-stream-and-has-disconnected-the
, I was able to get rid of TermDD message but I still loop in machine-user-machine authentication.
The following is TermDD message:
+
System
Provider
[ Name]
TermDD
EventID
56
[ Qualifiers]
49162
Level
2
Task
0
Keywords
0x80000000000000
TimeCreated
[ SystemTime]
2013-06-10T09:25:28.515308700Z
EventRecordID
26643
Channel
System
Computer
XTCSSPWA03.cen.csint.cz
Security
EventData
\Device\Termdd
10.190.64.208
0000040002002C000000000038000AC00000000038000AC000000000000000000000000000000000410200D0
Binary data:
In Words
0000: 00040000 002C0002 00000000 C00A0038
0008: 00000000 C00A0038 00000000 00000000
0010: 00000000 00000000 D0000241
In Bytes
0000: 00 00 04 00 02 00 2C 00    ......,.
0008: 00 00 00 00 38 00 0A C0   ....8..À
0010: 00 00 00 00 38 00 0A C0   ....8..À
0018: 00 00 00 00 00 00 00 00   ........
0020: 00 00 00 00 00 00 00 00   ........
0028: 41 02 00 D0               A..Ð
Also AnyConnect shows that upon successful authentication and DHCP operation, it catches some exception and reverts back from user to machine VLAN:
3876: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-6-INFO_MSG: %[tid=1436][mac=1,6,d4:85:64:b8:43:61]: {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: Authentication Success
3877: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2} canceling existing DHCP work
3878: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: ipv4: {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2} stop
3879: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (3) cdiOsIoctlSet: CDI_8023_FRAME_IO_ECHO, ifIndex(1), pData(0x0103FA38), dataLen(0) (cimdIo.cpp 2156)
3880: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (3) cdiOsIoctlSet: echo (cimdIo.cpp 2270)
3881: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2} creating a new DHCP work
3882: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-7-DEBUG_MSG: %[tid=1448]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: executing: CancelCmd [state: COMPLETE]
3883: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-6-INFO_MSG: %[tid=1436][mac=1,6,d4:85:64:b8:43:61]: {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: DHCP: Sending DHCP request
3884: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: queueing DHCP work
3885: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: ipv4: {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2} start
3886: XTCSSPWA03: 6 10 2013 11:24:44.259 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (3) cdiOsIoctlSet: CDI_8023_FRAME_IO_ECHO, ifIndex(1), pData(0x0103FA3C), dataLen(2) (cimdIo.cpp 2156)
3887: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (3) data follows ... (cimdIo.cpp 2159)
3888: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (3)      08 06                                                .. (cimdIo.cpp 2159)
3889: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (3) cdiOsIoctlSet: echo (cimdIo.cpp 2270)
3890: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (3) pEthTypes data follows ... (cimdIo.cpp 2273)
3891: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (3)      06 08                                                .. (cimdIo.cpp 2273)
3892: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv6 Connect {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2} starting
3893: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1448]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: executing: StartCmd [state: COMPLETE]
3894: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (0) S_ndisIoControl: returning cached xmitLinkSpeed: 100000000 bps (cimdIo.cpp 3558)
3895: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (0) NDIS OID: ifIndex=1 GET OID_GEN_LINK_SPEED(0x10107) datalen=4, cbRW=4 cbNeeded=0 acErr=0 winErr=0 (cimdIo.cpp 3686)
3898: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Network CS-wired-pass: AccessStateMachine current state = ACCESS_CONNECTED, received adapterState = authenticated
3899: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Network CS-wired-pass: port authentication succeeded
3900: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Network CS-wired-pass: AccessStateMachine new state = ACCESS_CONNECTED
3901: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: received Cancel event [state: COMPLETE]
3902: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: state: COMPLETE -> INIT
3903: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: received Get-Connectivity event [state: INIT]
3904: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: state: INIT -> WAIT_FOR_CONNECTIVITY
3905: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv4 Connectivity Result: IN_PROGRESS
3906: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1448]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: executing: GetConnectiviyCmd [state: WAIT_FOR_CONNECTIVITY]
3907: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv6 Connectivity Result: FAILURE
3908: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: received Check-Connectivity event [state: WAIT_FOR_CONNECTIVITY]
3909: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: (initial) ipCfg: IP:10.190.95.74(255.255.255.248) GW:10.190.64.1
3910: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1448]: Ipv4 {94B69AD2-E98C-4C94-BBC8-A94DC3894FE2}: executing: TestConnectivityCmd [state: WAIT_FOR_CONNECTIVITY]
3911: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1468][comp=SAE]: API (3) event: complete (portWorkList.c 130)
80: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAMSSO-7-DEBUG_MSG: %[tid=1524]: Tx CP Msg: <?xml version="1.0" encoding="UTF-8"?><SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:ssc="http://www.cisco.com/ssc" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/"> <SOAP-ENV:Body> <networkStateEvent>   <sequenceNumber>19</sequenceNumber>   <groupName>Local networks</groupName>   <networkName>CS-wired-pass</networkName>   <networkState>AcquiringIpAddress</networkState>   <adapterName>Broadcom NetXtreme Gigabit Ethernet</adapterName>   <serverVerifiedName>ise-2.csint.cz</serverVerifiedName> </networkStateEvent> </SOAP-ENV:Body></SOAP-ENV:Envelope>
3912: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1468][comp=SAE]: PORT (3) port: ARP_REQ (portMsg.c 731)
3913: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1468][comp=SAE]: NET (3) cdiOsIoctlSet: CDI_8023_FRAME_IO_SEND, ifIndex(1), pData(0x024EEB40), dataLen(64) (cimdIo.cpp 2156)
3914: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1468][comp=SAE]: NET (3) data follows ... (cimdIo.cpp 2159)
3915: XTCSSPWA03: 6 10 2013 11:24:44.275 -0100: %NAM-7-DEBUG_MSG: %[tid=1468][comp=SAE]: NET (3)      00 00 00 00 FF FF FF FF FF FF D4 85 64 B8 43 61     ........ ....d.Ca      08 06 00 01 08 00 06 04 00 01 D4 85 64 B8 43 61     ........ ....d.Ca      0A BE 5F 4A 00 00 00 00 00 00 0A BE 40 01 00 00     .._J.... ....@...      00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ........ ........ (cimdIo.cpp 2159)
3941: XTCSSPWA03: 6 10 2013 11:24:44.290 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (3) cdiOsIoctlSet: echo (cimdIo.cpp 2270)
3942: XTCSSPWA03: 6 10 2013 11:24:44.290 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv4 Connectivity Result: SUCCESS
3943: XTCSSPWA03: 6 10 2013 11:24:44.290 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: Ipv6 Connectivity Result: FAILURE
3944: XTCSSPWA03: 6 10 2013 11:24:44.290 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: ACE: adapter SM current: state(STATE_AUTHENTICATED), event(EVENT_IP_CONNECTIVITY)
3945: XTCSSPWA03: 6 10 2013 11:24:44.290 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: ACE: adapter SM state change: STATE_AUTHENTICATED -> STATE_CONNECTED
3946: XTCSSPWA03: 6 10 2013 11:24:44.290 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: handleEventAndDoStateTransitionAction action : ACTION_IP_CONNECTIVITY
3947: XTCSSPWA03: 6 10 2013 11:24:44.290 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (0) S_ndisIoControl: returning cached xmitLinkSpeed: 100000000 bps (cimdIo.cpp 3558)
3948: XTCSSPWA03: 6 10 2013 11:24:44.290 -0100: %NAM-7-DEBUG_MSG: %[tid=1436][comp=SAE]: NET (0) NDIS OID: ifIndex=1 GET OID_GEN_LINK_SPEED(0x10107) datalen=4, cbRW=4 cbNeeded=0 acErr=0 winErr=0 (cimdIo.cpp 3686)
1: XTCSSPWA03: 6 10 2013 11:24:54.007 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {25CBB996-92ED-457E-B28C-4774084BD562} LogLevel=0xF
2: XTCSSPWA03: 6 10 2013 11:24:54.007 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: GetWrappedDllName: retrieved C:\windows\system32\authui.dll.
3: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: LoadLib({25CBB996-92ED-457E-B28C-4774084BD562}): Attempting to load Dir=C:\windows\system32, FileName=authui.dll
4: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000001FC050) instantiated for CLSID:{25CBB996-92ED-457E-B28C-4774084BD562}
5: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {3DD6BEC0-8193-4FFE-AE25-E08E39EA4063} LogLevel=0xF
6: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: GetWrappedDllName: retrieved C:\windows\system32\authui.dll.
7: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: LoadLib({3DD6BEC0-8193-4FFE-AE25-E08E39EA4063}): Attempting to load Dir=C:\windows\system32, FileName=authui.dll
8: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000001FC850) instantiated for CLSID:{3DD6BEC0-8193-4FFE-AE25-E08E39EA4063}
9: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {503739D0-4C5E-4CFD-B3BA-D881334F0DF2} LogLevel=0xF
10: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: GetWrappedDllName: retrieved C:\windows\System32\VaultCredProvider.dll.
11: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: LoadLib({503739D0-4C5E-4CFD-B3BA-D881334F0DF2}): Attempting to load Dir=C:\windows\System32, FileName=VaultCredProvider.dll
12: XTCSSPWA03: 6 10 2013 11:24:54.022 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000003A30B0) instantiated for CLSID:{503739D0-4C5E-4CFD-B3BA-D881334F0DF2}
13: XTCSSPWA03: 6 10 2013 11:24:54.038 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {6F45DC1E-5384-457A-BC13-2CD81B0D28ED} LogLevel=0xF
14: XTCSSPWA03: 6 10 2013 11:24:54.038 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: GetWrappedDllName: retrieved C:\windows\system32\authui.dll.
15: XTCSSPWA03: 6 10 2013 11:24:54.038 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: LoadLib({6F45DC1E-5384-457A-BC13-2CD81B0D28ED}): Attempting to load Dir=C:\windows\system32, FileName=authui.dll
16: XTCSSPWA03: 6 10 2013 11:24:54.038 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000003AF710) instantiated for CLSID:{6F45DC1E-5384-457A-BC13-2CD81B0D28ED}
17: XTCSSPWA03: 6 10 2013 11:24:54.038 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {8BF9A910-A8FF-457F-999F-A5CA10B4A885} LogLevel=0xF
18: XTCSSPWA03: 6 10 2013 11:24:54.038 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: GetWrappedDllName: retrieved SmartcardCredentialProvider.dll.
19: XTCSSPWA03: 6 10 2013 11:24:54.038 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: LoadLib({8BF9A910-A8FF-457F-999F-A5CA10B4A885}): Attempting to load Dir=, FileName=SmartcardCredentialProvider.dll
20: XTCSSPWA03: 6 10 2013 11:24:54.053 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000003B7D70) instantiated for CLSID:{8BF9A910-A8FF-457F-999F-A5CA10B4A885}
21: XTCSSPWA03: 6 10 2013 11:24:54.053 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {94596C7E-3744-41CE-893E-BBF09122F76A} LogLevel=0xF
22: XTCSSPWA03: 6 10 2013 11:24:54.053 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: GetWrappedDllName: retrieved SmartcardCredentialProvider.dll.
23: XTCSSPWA03: 6 10 2013 11:24:54.053 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: LoadLib({94596C7E-3744-41CE-893E-BBF09122F76A}): Attempting to load Dir=, FileName=SmartcardCredentialProvider.dll
24: XTCSSPWA03: 6 10 2013 11:24:54.053 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000003C03D0) instantiated for CLSID:{94596C7E-3744-41CE-893E-BBF09122F76A}
25: XTCSSPWA03: 6 10 2013 11:24:54.053 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {AC3AC249-E820-4343-A65B-377AC634DC09} LogLevel=0xF
26: XTCSSPWA03: 6 10 2013 11:24:54.053 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: GetWrappedDllName: retrieved C:\windows\System32\BioCredProv.dll.
27: XTCSSPWA03: 6 10 2013 11:24:54.053 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: LoadLib({AC3AC249-E820-4343-A65B-377AC634DC09}): Attempting to load Dir=C:\windows\System32, FileName=BioCredProv.dll
28: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000003CABC0) instantiated for CLSID:{AC3AC249-E820-4343-A65B-377AC634DC09}
29: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {B12744B8-5BB7-463A-B85E-BB7627E73002} LogLevel=0xF
30: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CClassFactory(00000000001FFF00) CreateInstance calling CoCreateInstance on MS password cred prov
31: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {6F45DC1E-5384-457A-BC13-2CD81B0D28ED} LogLevel=0xF
32: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: GetWrappedDllName: retrieved C:\windows\system32\authui.dll.
33: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: LoadLib({6F45DC1E-5384-457A-BC13-2CD81B0D28ED}): Attempting to load Dir=C:\windows\system32, FileName=authui.dll
34: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000003D3220) instantiated for CLSID:{6F45DC1E-5384-457A-BC13-2CD81B0D28ED}
35: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000003DB880) instantiated for CLSID:{B12744B8-5BB7-463A-B85E-BB7627E73002}
36: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: DllGetClassObject CLSID: {E74E57B0-6C6D-44D5-9CDA-FB2DF5ED7435} LogLevel=0xF
37: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: GetWrappedDllName: retrieved C:\windows\system32\certCredProvider.dll.
38: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: LoadLib({E74E57B0-6C6D-44D5-9CDA-FB2DF5ED7435}): Attempting to load Dir=C:\windows\system32, FileName=certCredProvider.dll
39: XTCSSPWA03: 6 10 2013 11:24:54.069 -0100: %NAMCP-7-DEBUG_MSG: %[tid=2680]: CredProvider(00000000003E3EE0) instantiated for CLSID:{E74E57B0-6C6D-44D5-9CDA-FB2DF5ED7435}
3963: XTCSSPWA03: 6 10 2013 11:24:59.247 -0100: %NAM-7-DEBUG_MSG: %[tid=2460]: SysLib:DBG: .\src\os\win\osAsync_win.c:233: => SL_STATUS_NO_CONNECTION
3964: XTCSSPWA03: 6 10 2013 11:24:59.247 -0100: %NAM-7-DEBUG_MSG: %[tid=2460]: SysLib:DBG: .\src\ipc\win\ipcPipeBase_win.c:102: => SL_STATUS_NO_CONNECTION
3965: XTCSSPWA03: 6 10 2013 11:24:59.262 -0100: %NAM-7-DEBUG_MSG: %[tid=2460]: SysLib:DBG: .\src\ipc\win\ipcPipeBase_win.c:194: => SL_STATUS_NO_CONNECTION
3966: XTCSSPWA03: 6 10 2013 11:24:59.262 -0100: %NAM-7-DEBUG_MSG: %[tid=2460]: SysLib:DBG: .\src\ipc\ipcFuncs.c:105: => SL_STATUS_NO_CONNECTION
3967: XTCSSPWA03: 6 10 2013 11:24:59.262 -0100: %NAM-7-DEBUG_MSG: %[tid=2460]: CAUGHT: NoConnectionException
3968: XTCSSPWA03: 6 10 2013 11:24:59.262 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: CoreLib:TRACE: context=acnam, thread join, ThreadImpl.cpp:58, m00585050, err=0(OS_OK), thread_id=2460
3969: XTCSSPWA03: 6 10 2013 11:24:59.262 -0100: %NAM-7-DEBUG_MSG: %[tid=1436]: CoreLib:TRACE: context=acnam, thread join, ThreadImpl.cpp:58, m00585838, err=0(OS_OK), thread_id=3692
89: XTCSSPWA03: 6 10 2013 11:25:06.367 -0100: %NAMSSO-7-DEBUG_MSG: %[tid=1228]: ServiceControlHandlerEx:WTS_SESSION_LOGOFF, Session ID: 1
If we do not change VLAN from machine to user, it works just fine.
Have anybody seen this problem? Have anybody fixed it?
Thanx, Martin

Hi,
unfortunately not.
I have gone through extensive troubleshooting from Microsoft and Cisco sides twice and the result is:
1) AnyConnect performs EAPol logoff when it detects RDP session termination. So it goes from user to machine authentication
2) Windows 7 performs RDP session termination when IP address changes due to the change of VLAN (from machine VLAN to user VLAN)
Cisco claims that AnyConnect behavior is correct and Microsoft claims that they do not want to change this behavior (reset of RDP session).
I can imagine that Cisco can detect whether RDP session was terminated due to the IP address change or not and do not revert back to machine authentication in such a case.
In fact there was nobody at Cisco that was willing to listen to me or accept this like something that needs a fix. The only thing you can do is to enable "Extend connection beyond logoff". AnyConnect does not send EAPol logoff if it detects RDP session termination and you can establish another RDP session which does not fail and you stay connected with RDP.
Martin

802.1x dynamic VLAN assignment with Radius NPS Server

I can NOT get the NPS and Cisco 3550 switch to drop the authenticated user in a VLAN.
I have followed this documentation,
http://msdn.microsoft.com/en-us/library/dd314181(v=ws.10).aspx
that basically says to use these Radius attributes,
Tunnel-Medium-Type : 802
Tunnel-Pvt-Group-ID : My_VLAN_Number (also tried VLAN name)
Tunnel-Type : VLAN
There is some Cisco documentation that says to use Vendor Specific attributes Cisco-AV-Pair,
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2950/software/release/12-1_19_ea1/configuration/guide/2950scg/swauthen.html#wpxref83693
and I have also tried that,
cisco-avpair= "tunnel-type(#64)=VLAN(13)"
cisco-avpair= "tunnel-medium-type(#65)=802 media(6)"
cisco-avpair= "tunnel-private-group-ID(#81)=vlanid"
My user authenticates on the port fine, but doesn't get put into a VLAN. If I add "sw acc vlan 110" then the user authenticates and then does get an IP address in that VLAN and all is well.
Anybody know how to get dynamic VLAN assignment working with NPS?
NPS on Win 2012 R2
Domain controller separate Win 2012 R2 server
Cisco 3550 switch

Hi All, Can any one guide me to
configure 802.1x with acs 5.0. Its totally new look and m not able to
find document related to 802.1x.Thanks
Hi,
Check out the below link on how to configure 802.1x and ACS administration hope to help !!
http://www.cisco.com/en/US/tech/tk389/tk814/technologies_configuration_example09186a00808abf2d.shtml#MDA
Ganesh.H

Dynamic vlan assignment with openldap

Hi,
I have a scenario where my customer has an ACS 5.2 and couple WLCs. the customer has also a openldap database and needs to do dynamic vlan assignement for his wireless user against this database. I know that for Active directory it works, please advise if it does as well for openldap and how?
Regards,

No it doesnt work if you are using mschap v2 here is a grid of the supported eap based protocols and the directory services:
You can find this information here:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/eap_pap_phase.html#wp1045863
Hope this helps.

Acs and Dynamic vlan assignment problem

Similar Messages

Maybe you are looking for