ACS Engine IP always resets to 0.0.0.0

Hi,
We have a problem with our ACS engines. We have 2 ACS Engines and the problem is we cannot disable it as a DHCP client. When its ethernet connection goes down, its IP address resets to 0.0.0.0. The static IP address that we set on it does not retain when we unplug its ethernet connection. We're thinking that this is because the "DHCP enabled" is still set to "Yes" even though we have configured it to have a static IP. We have two new ACS engines and both have the same problem. Hope you guys can help.
Thanks in advance.

Hi,
Yes, we have already tried that and this is the output:
+++++++++++++after entering the IP parameters++++++++++++
New Configuration:
DHCP: No
IP Address: 192.168.1.21
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
DNS Servers: 192.168.1.21
IP Address is reconfigured.
Confirm the changes? [Yes]:
New ip address is set.
Default gateway is set to 192.168.1.1.
DNS servers are set to 192.168.1.21.
Test network connectivity [Yes]: Yes
Enter hostname or IP address: 192.168.1.1
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time<10ms TTL=255
Reply from 192.168.1.1: bytes=32 time<10ms TTL=255
Reply from 192.168.1.1: bytes=32 time<10ms TTL=255
Reply from 192.168.1.1: bytes=32 time<10ms TTL=255
Ping statistics for 192.168.1.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
++++++++++++++then ACS services restart++++++++++++++++
+++++++++++After entering the show command+++++++++++++
Cisco Secure ACS: 4.1.1.23
Appliance Management Software: 4.1.1.23
Appliance Base Image: 4.1.1.4
CSA build 4.0.1.543.2: (Patch: 4_0_1_543)
Session Timeout: 10
Last Reboot Time: Thu Feb 21 18:26:49 2008
Current Date & Time: 2/21/2008 18:31:48
Time Zone: (GMT-06:00) Central Time (US & Canada)
NTP Server(s): NTP Synchronization Disabled.
CPU Load Free Disk Free Physical Memory
0.00% 16.5 GB 794 MB
Appliance IP Configuration
DHCP Enabled. . . . . . . . . . .: Yes
IP Address. . . . . . . . . . . .: 192.168.1.21
Subnet Mask . . . . . . . . . . .: 255.255.255.0
Default Gateway . . . . . . . . .: 192.168.1.2
DNS Servers . . . . . . . . . . .:
--- Please hit enter to continue ---
CSAdmin running
CSAuth running
CSDbSync running
CSLog running
CSMon running
CSRadius running
CSTacacs running
CSAgent running
++++++++++++++++then we enter the reboot command++++++++++++++++++++
+++++++++After the reboot, this is the result of the show command:+++++++++++++
Appliance IP Configuration
DHCP Enabled. . . . . . . . . . .: Yes
IP Address. . . . . . . . . . . .: 169.254.94.164
Subnet Mask . . . . . . . . . . .: 255.255.0.0
Default Gateway . . . . . . . . .:
DNS Servers . . . . . . . . . . .:
After the reboot, the IP is not saved.
Regards

Similar Messages

  • Bug report: App Builder always resetting pagination

    See my earlier post about this at
    Re: PPR breaks browser Back button
    I thought (mistakenly, it turns out) that the PPR stuff was to blame for the App Builder main page always "resetting" to the first set of rows.
    But when I created a report using a PPR template at
    http://htmldb.oracle.com/pls/otn/f?p=24317:138
    paginate to the 3rd set of rows, run some other page and come back to the PPR page, it does indeed properly remember which set it was on i.e. pagination is NOT reset.
    But when I do the same thing in the App Builder...Go to the 3rd set of pages, run a page from there. Now when I click on the Edit Application link on the Developer Toolbar, it throws me back to the first set of pages :-(
    I just realized the reason is that the Edit Application link in the Developer Toolbar is
    http://htmldb.oracle.com/pls/otn/f?p=4000:1:3150046948585447489::NO:1,4150,<b>RP</b>:FB_FLOW_ID,FB_FLOW_PAGE_ID,F4000_P1_FLOW,F4000_P4150_GOTO_PAGE,F4000_P1_PAGE:24317,138,24317,138,138
    It has the RP in there that does the pagination reset! Why?
    The same link in Version 1.6 is
    f?p=4000:1:1514638425792267178::NO:1,4150:FB_FLOW_ID,FB_FLOW_PAGE_ID,F4000_P1_FLOW,F4000_P4150_GOTO_PAGE,F4000_P1_PAGE:102,80,102,80,80
    No RP there.
    What is the reason for this change?
    Thanks

    You could delete 20 pages by just staying on the page
    detail pages and hitting delete, I've done exactly
    that before.Carl, not sure what you mean. I outlined my exact steps to delete a page above and how it keeps throwing me back to Page 0, etc.
    What do you men by "staying on the page detail pages and hitting delete"? You click Delete once, you are taken to the Delete Confirmation page.
    So how can you delete multiple pages at once?
    [I had another feature request some time back about being able to export or delete "Page Groups" that would come in handy here as well]
    Deleting 20 pages is an edge case lets say you had 11
    pages your pagination shows 1-10 you go to page 11
    and delete it you'd have the same problem. As I said, its the same thing as any email client or any software really displaying a list of items and you open an item and delete it. Where to go next? There should be options for this kind of thing.
    You can be
    fairly certain that there will be some sort of report
    enhancement that if you try and return rows of say
    20-30 and there are only 19 the report engine will
    return you 10-19 so you don't get a broken report.Yup, this is a very common "newbie" mistake where there is a search filter on a report region and a branch back to the same page. If I forget to reset pagination on the Branch Attributes page, and Search 1 returns 25 and I am on 20-25 and I start another Search that returns 10 rows, the report "breaks" since it tries to display Rows 20-25 of 10!
    Are you saying that the "reset pagination" checkbox on the Branch page will no longer be necessary in upcoming versions? The report engine will be smart enough to "figure out" what set of rows to return based on what rows (x to y) the page was "stuck at" before?
    Thanks

  • Mouse tracking always reset to a specific area point

    Hi,
    My iMac mouse always reset to a specific area of my screen every time I move it.
    I thought that it was the magic mouse tracking that was bugging but it's not : the same problem occurs when I'm using the ScreenSharing app with my computer on sharing mode.
    I tried to restart the computer, empty the PRAM after unplugging the computer but nothing worked..
    Here's the specs of my iMac :
    iMac 27-inch, Late 2012
    3,4 GHz Intel Core i7
    32 Gb of ram
    NVIDIA GeForce GTX 680MX 2048 Mb
    OS X Yosemite 10.10.1
    Someone could help me please?

    Everything is ok finally : I haven't seen that the pen of my graphic tablet was layed down on it..! -_-

  • My Blackberry 9320 always reset !

    Hello everybody !
    I've bought my blackberry 9320 two weeks ago, but it always reset ! I've tried to do a hard reset, a soft reset and a logicial reset, but it doesn't work anyway !
    Does someone have the same problem ?
    Can someone help me ?
    Thanks you !

    Hi and Welcome to the Community!
    I recommend that you attempt to boot into Safe Mode:
    KB17877 How to start a BlackBerry smartphone in Safe Mode
    It may take you multiple attempts to get the ESC key sequence (press/release/hold) correct, so be patient. When successfully into Safe Mode, see what happens.
    If the behavior ceases, then think carefully...what happened just before this behavior started? A new app? An update? A Theme? Something else? Think carefully as the smallest change could be causal...and attempt to undo whatever that was.
    But if the behavior continues in Safe Mode, then you may need to consider more drastic actions -- WIPE, OS Reload, BBSAK Wipe/Reload, and the "Bare Bones" OS Reload Process. To prepare, you should be sure that you have a full backup to your PC...please review the Backup link in my auto-sig on this post for instructions.
    You may also need the use of these tricks:
    KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
    KB27956 How to recover a BlackBerry smartphone from any state
    http://crackberry.com/blackberry-101-lecture-12-ho​w-reload-operating-system-nuked-blackberry
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • When i use my apple id ,always reset my password ,i think somebody use how to secure

    when i use my apple id ,always reset my password ,i think somebody use how to secure

    Hi WOLF86,
    Welcome to the Support Communities!
    The first thing I would suggest is to quit the Mac App Store application.  Then go to the Apple - My Apple ID website and click on "Manage your Apple ID" to confirm your settings.   If you can't remember your password, you can reset it from this website.
    The next thing I would try is to open your iTunes application, and on the menu bar, click on Store > View Account. Make sure your billing information and shipping details are correct.  (You may be requested to re-enter your credit card security code, then be sure to click Done).
    Finally, restart your computer and launch the Mac App Store and try your purchase again.
    These articles will provide additional information:
    Frequently asked questions about Apple ID
    http://support.apple.com/kb/HT5622
    iTunes 11 for Mac: Manage your iTunes Store account
    http://support.apple.com/kb/PH12299
    Troubleshooting the Mac App Store
    http://support.apple.com/kb/ts3624
    I hope this information helps ....
    - Judy

  • Why is itunes always resetting like it was just installed? It's always wanting you to confirm everything when you open it.

    Why is itunes always resetting like it was just installed? It's always wanting you to confirm everything when you open.

    McAfee AntiVirus by any chance? See the thread  Why does iTunes delete my itunesprefs.xml?
    tt2

  • Contract reference field always resets to contract has no objects

    Hi All,
    When I'm configuring custom contract types in RE-FX the contract reference field always resets to 'contract has no objects' when I save it, no matter what value I enter such as 'objects are leased in'.
    Would anyone know why this might be?
    Thanks very much

    Hi Jamie,
    Please check contract reference, Flex RE type, Fields in Contract type node in IMG

  • I own an old PowerBook G3 that turns o only on battery. And, even so, always resets time and date. Whenever I connect the power cable, it turns off.

    I own an old PowerBook G3 that turns o only on battery. And, even so, always resets time and date. Whenever I connect the power cable, it turns off. In addition, I a interested in refurbishing my old G3. And, a lesser old G4 LCD that shows a yellow vertical hair-width stripe.
    Thank you in advance.

    What model PowerBook? The internal PRAM battery has discharged and is not recharging. You'll need to replace the battery. This site has instructions. http://www.ifixit.com/Browse/PowerBook
    The PRAM battery is not easy to change on some PB G3 models. I changed the battery on a Wallstreet model. Had to totally disassemble to do it. Bought the replacement battery on eBay.
     Cheers, Tom

  • Notifications setting always reset after I restart. can't keep the setting i changes

    after upgrade to osX 10.10. the notifications setting can not save what i change.
    always reset the setting after I restart yosemite.
    how to fix it?

    Seems to be a problem among many users.
    https://discussions.apple.com/thread/6605975
    https://discussions.apple.com/message/26851563#26851563
    https://discussions.apple.com/message/26857242#26857242
    https://discussions.apple.com/message/26863504#26863504

  • Extra server on cisco ACS engine

    I'm a bit curious about the way the cisco ACS engine (the cisco-built hardware) sets up servers initially. Most of the documentation I have is for windows, so I was a bit confused when, after the initial configuration there were two "AAA Servers" shown in the configuration, one called "Self" with the IP address I defined, and the other with the name I defined and a different address.
    Has anyone else encountered this? Will it cause problems? and is there a way to get rid of it?
    Thanks

    That is a known issue with acs appliance, but nothing to worry about. Make sure you have this setting in acs,
    acs--->network configuration--->Proxy dis table---> Bring Deleverance1 in the fwd to box and your server name in the left box.
    Incase you dont see proxy dis table , then you need to enable it
    Interface configuration---> Advance option ---> Put a check in distribution table.
    Regards,
    ~JG
    Please do rate helpful posts

  • Cisco ACS Engine appliance 1120 software upgrade

    I want to upgrade my Cisco ACS Engine appliance 1120 from software version 3.3 to the latest version (5.x). How do I go about this? Someone should help please.

    It is highly suspicious that you would have a 1120 appliance that is running 3.3
    ACS 3.3 was with the ACS solution engine 1111, 1112 and 1113.
    ACS 5 requires the appliance 1120/1121 so it requires an appliance change. I'm puzzled about how you could be running 3.3 for 1120 since there is no installation DVD for that.
    As a general thing, one has to follow the ACS 5 migration guide on cisco.com that explains the process quite well. You need to go to acs 4.1/4.2 to migrate to 5.
    http://www.cisco.com/en/US/partner/docs/net_mgmt/cisco_secure_access_control_system/5.1/user/guide/migrate.html
    Nicolas

  • Mouse tracking speed always reseted

    when i plug out my mouse (razer deathadder) then use the trackpad only and plug the mouse in again the tracking speed ist always reseted to the 4th bar.
    why is that happening and how can i make the os the save my setting?
    thanks!
    ps: apple i hate you for removing the possibility to shut down the trackpad while mouse-use. it is so annyoing while typing. saussage fingers helps a bit but i want the old option back!!

    mr.omsn wrote:
    when i plug out my mouse (razer deathadder) then use the trackpad only and plug the mouse in again the tracking speed ist always reseted to the 4th bar.
    why is that happening and how can i make the os the save my setting?
    make a new user account and log into it. does the same thing happen there?
    thanks!
    ps: apple i hate you for removing the possibility to shut down the trackpad while mouse-use. it is so annyoing while typing. saussage fingers helps a bit but i want the old option back!!
    they didn't remove it. they just moved it. this option is available in system preferences->universal access->mouse&trackpad.

  • Integrate ACS engine with AD

    dears
    i have ACS Engine version 5.0  and i want to integrate it with MORE than AD . can anyone advise how can i do it.ASAP PLEAS
    OSAMA

    ACS 5 can only be joined to one domain at a time, but it can process authentication requests for users on multiple domains as long as there are trust relationships established.

  • ACS Engine Failover Deployment

    Hello,
    I want reference guide for implementing ACS Engine Failover Deployment, I could not find any scenario for deploying Failover.
    Thanks

    This is due to this bug ,
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?caller=pluginredirector&method=fetchBugDetails&bugId=CSCso39795
    Regards,
    ~JG
    Do rate helpful posts

  • Shared Variable Engine not always started

    I'm experiencing an intermittent problem with the LabVIEW variable engine.  The National Instruments Variable Engine service is configured to start automatically with Windows but that doesn't seem to always be the case.  Every now and then I'll load my application only to find red LED indicators on all of the controls accessing my shared variables.  I'll bring up the variable manager and stop/start the service, restart my application and then they're all green LEDs and everything works.  Any idea what might be causing this?
    Thanks,
    - Kevin Handy

    Hi Kevin.  I don't know what causes the problem, but I have seen it on our systems as well.
    Our solution was to have our application stop and then start the variable engine every time
    it launches.  Stopping might not be ok for you depending on how your applications are
    architected, but for us it is fine.
    We use two System Exec.vi calls, with the following strings:
    net stop "national instruments variable engine"
    net start "national instruments variable engine"
    Haven't had any instances of the application coming up w/o the variable engine since
    we added this initialization step.
    Matt

Maybe you are looking for