ACS SE base image UPgrade

HI,
We have upgraded the ACS SE 1112 as following.
Cisco Secure ACS : 4.0.1.42 to 4.1.1.23
Appliance Management Software:4.0.1.42to 4.1.1.23
Appliance Base Image needs to upgrade from 3.3.1.8 to 4.1.1.4 but we are not able to download the package at download centre as it is not available.
Kindly suggest for base image upgrade.
Regards,

It should work as long as you don't miss anything, and yes you are supposed to install an agent that matches the version you are running. You might want to go ahead and put the latest updates on the ACS before you put it into operation. The process is kind of different than other updates. You might want to read my other ACS posts. I recently killed one of my ACS boxes because I did not install the CSUPdate cumulative patch before installing the lastest patch of the same rev level. (i.e. read directions carefully). Make sure you do an FTP backup before updating the software. If anything goes wrong you could have to reimage the box. There were lots of bug fixes in the updates since 4.1.1.
Randy

Similar Messages

How to add MS Office add-in from inside a Thinapp 5 virtual application to a MS Office 2013 suite that is installed on a base image

Hi,
We have the following solution:
VMware Horizon View 5.3.1
Non-persistent Linked-clone pool with delete VM after logoff
Windows 8.1 Update 1 Enterprise 64 bit
MS Office 2013 32-bit installed on image
Thinapps registered for each user from logonscript with thinreg.exe command. Thinapps is located on a network share
Native Windows roaming profiles with appdata/roaming, appdata/local without appdata/locallow(persona management does not support Windows 8.1 in View 5.3.1)
This is our issue:
We have a 3rd party application with a couple Thinapp entrypoints(exe files) and in the Thinapp package process we also installed Office addins. We tested that the Add-ins was opened inside Outlook, Word and Powerpoint before post installation scan.
The problem is that the add-ins is not added to Office 2013 before or after the Thinapp is started on a test client.
I have tried several changes in the package.ini and virtual filesystem attributes(no registry changes yet):
Package.ini:
ChildProcessEnvironmentExceptions=WINWORD.EXE;EXCEL.EXE;POWERPNT.EXE;OUTLOOK.EXE;
ChildProcessEnvironmentDefault=External
ChildProcessEnvironmentExceptions=excel.exe;outlook.exe;powerpnt.exe;winword.exe
ChildProcessEnvironmentDefault=Virtual
VirtualizeExternalOutOfProcessCOM=0
DirectoryIsolationMode=Merged
RegistryIsolationMode=Merged
I have also read that you could make entrypoints to the locally installed Office 2013, but I get errors on the build process. ref. link: http://edwinfriesen.nl/content/?p=105#comments
The best thing would be if the add-ins were added in the logon process together with thinreg.exe, but if that is not supported, the add-ins must be added to Office either in a custom Office shortcut/entry point or after starting the Thinapp virtual application.
Remember that the application needs to registered every times the user logon, because we use a non-persistent View pool.
I would really appreciate if somebody could tell me how to add Office add-ins from inside a Thinapp virtual application/package to a locally installed MS Office 2013 suite on a Windows "base" image?
We do not want to add the whole Office suite to the Thinapp virtual package and not add the add-ins trough GPO,SCCM etc.

What about the COM object parameters in package.ini ?
We can live with scripting in logon or changed logon scripts etc.
And you don't no need to lock in the project files.
From package.ini documentation:
ObjectTypes Parameter
The ObjectTypes parameter specifies a list of virtual COM object types that are visible to other applications in
the physical environment. You can use scripts, such as VBScripts, to call objects that start captured applications.
An object type is registered to only one native or virtual application at a time. If you install Office 2003 on the
native machine and want to use a virtual Office 2007 package, you must determine whether to have the virtual
or native application handle the object types.
If you want the virtual Office 2007 to handle the object types, you can leave the ObjectTypes setting in the
Package.ini file, build the package, and register it using the thinreg.exe utility. If you want the native Office
2003 to handle the object types, you must remove the ObjectTypes setting from the Package.ini file before
building and registering the package.
You cannot add random entries to the ObjectTypes parameter.
You can only remove entries that were generated by the capture process.
Example: Starting a Virtual Application When a COM Object is Created
If a script or a native application creates an Excel.Application COM object or other COM objects listed in the
ObjectTypes parameter, ThinApp starts the virtual package.
[Microsoft Office Excel 2007.exe]
ObjectTypes=Excel.Application;Excel.Application.12;Excel.Chart;
Excel.Macrosheet;Excel.Sheet; Excel.Workspace

When can I test base images in development?

The latest base image for Firefox OS is tagged 188 [1] and it contains Firefox OS 2.2.
I encounter a weird bug that doesn't permit me to install any version of Firefox OS but 2.2 on my Flame. [2]
So I think that testing a new base image based on v. 3.0 let me install Firefox OS 3.0 and to fix that bug.
How can I do that without compiling everything by myself, because I don't have enough free space and RAM on my old PC?
Thank you very much!
[1] https://developer.mozilla.org/en-US/Firefox_OS/Developer_phone_guide/Flame/Updating_your_Flame#Updating_your_Flame's_software
[2] https://bugzilla.mozilla.org/show_bug.cgi?id=1112663

Hi Airon90,
For developer-related questions, and for flashing issues and instructions, you can write to the dev-b2g mailing list, where other developers will be able to suggest possible solutions:
* [https://lists.mozilla.org/listinfo/dev-b2g dev-b2g mailing list]
- Ralph

The value should be set for Base image URL and Image file directory

Hi experts
Now customer has the following issue.
XML Publisher concurrent request, using RTF layout template with LOGO, does not generate the LOGO for Excel output.
but in output formats PDF, it is shown normally.
from the debug log, we can found the following error message
======
[051812_054716051][][ERROR] Could not create an image. Set html-image-dir and html-image-base-uri correctly.
======
so I tell the customer to do the following action plan.
1. in XML Publisher Administrator resp > Administration expand the HTML Output section.
2a. enter a value for 'Base image URI'
2b. enter a value for 'Image file directory'
Customer set the value as following and retest this issue,but he found the issue is not solved.
Base image URI: /u01/r12/ebssnd/apps/apps_st/comn/java/classes/oracle/apps/media/XXSLI_SONY_LIFE_LOGO.gif
Image file directory: /u01/r12/ebssnd/apps/apps_st/comn/java/classes/oracle/apps/media
I verified 'Base image URI' and 'Image file directory' settings:
1) Change output type to HTML.
2) Click the Preview.
but the image is correctly displayed on HTML, so I think the issue is caused by user's uncorrectly setting of the base image URL and/or image file directory
but could anyone give me some advice on which value should be set for Base image URL and Image file directory
Regards
shuangfei

First thing to do is to edit the post and use some tags to format the code as it is unreadable and too much!
Read the FAQ (https://forums.oracle.com/forums/help.jspa) to find out how to do this.
Next we need to know the jdev version you are using!
As the code is generated I would first try to generate it again after the db change.
Timo

SCOM 2012 Agent - Best Practices with Base Images

I've read through the
SCOM 2012 agent installation methods technet article, as well as how to
install the SCOM 2012 agent via command line, but don't see any best practices in regards to how to include the SCOM 2012 agent in a base workstation image. My understanding is that the SCOM agent's unique identifier is created at the time of client installation,
is this correct? I need to ensure that this is a supported configuration before I can recommend it.
If it is supported, and it does work the way I think it does, I'm trying to find out a way to strip out the unique information so that a new client GUID will be created after the machine is sysprepped, similar to how the SCCM client should be stripped of
unique data when preparing a base image.
Has anyone successfully included a SCOM 2012 (or 2007 for that matter) agent in their base image?
Thanks,
Joe

Hi
It is fine to build the agent into a base image but you then need to have a way to assign the agent to a management group. SCOM does this via AD Integration:
http://technet.microsoft.com/en-us/library/cc950514.aspx
http://blogs.msdn.com/b/steverac/archive/2008/03/20/opsmgr-ad-integration-how-it-works.aspx
http://blogs.technet.com/b/jonathanalmquist/archive/2010/06/14/ad-integration-considerations.aspx
http://thoughtsonopsmgr.blogspot.co.uk/2010/07/active-directory-ad-integration-when-to.html
http://technet.microsoft.com/en-us/library/hh212922.aspx
http://blogs.technet.com/b/momteam/archive/2008/01/02/understanding-how-active-directory-integration-feature-works-in-opsmgr-2007.aspx
You have to be careful in environments with multiple forests if no trust exists.
http://blogs.technet.com/b/smsandmom/archive/2008/05/21/opsmgr-2007-how-to-enable-ad-integration-for-an-untrusted-domain.aspx
http://rburri.wordpress.com/2008/12/03/untrusted-ad-integration-suppress-misleading-runas-alerts/
You might also want to consider group policy or SCCM as methods for installing agents.
Cheers
Graham
Regards Graham New System Center 2012 Blog! -
http://www.systemcentersolutions.co.uk
View OpsMgr tips and tricks at
http://systemcentersolutions.wordpress.com/

Can I make a *smaller* base image for a mobileme gallery?

So as near as I can tell, I cannot set the maximum size for an image in a mobileme gallery...is there a preset for that? I realize that I can disable downloading, but if I want a base image that is more "facebooky" in resolution, can I specify that?
I'm looking for something smaller than the default "1024x680" that I seem to be getting. I'm seeing any effect with the image export presets.
-John

OK, thanks for the copy/paste info, TD. However, when I go
File>Import to Library>documents>
The picture/document I want is grayed out, and can't be lifted.
I also Print>Saved as PDF, but that document is also grayed out. None of the other options after File>Import shows anything that looks like what I want.
I also highlighted the map on Pages, then "right clicked" (Cont+Click), and then Capture Selection from screen", but I don't know what I have after highlighting. It sounds like I took a picture, and there is a highlighted image of what I "captured" but when I tried to drag to iPhoto, it disappeared.

Wireless Controller Image Upgradation

Cisco recommends image upgrade procedure on 4402 WLC to the latest release 4.1 to be performed in three steps:-
1)3.1.105.0 ------>3.2.78.0
2)3.2.78.0 ------->3.2.195.13
3)3.2.195.13------>4.1.185.0
Unfortunately, while upgrade from 3.1.105.0 ------>3.2.78.0
I got the below error message as shown on both CLI and GUI as well.
"TFTP Failure while storing in flash!"
I have tried Tftpd32 which Cisco recommends also tried other TFTP versions a couple of times but resulted in the same error.
Could someone please suggest TFTP server software package which will support file transfers larger than 32 MB ?
Awaiting your reply and valuable suggestions.

Hey Sanoj,
I've got similar restrictions on some of my controllers. One thing to keep in mind is that the controller won't actually load the new OS until you reboot. Depending on how restrictive your change control process is, you may be able to attempt loadint the software outside of your change window. Once you have a successful tftp transfer, you can schedule a window for a reboot, which will actually load the new OS. I wouldn't leave too much time between the tftp transfer and then reboot, but I understand your frustration with the tftp transfers... I have about an 80% failue rate on tftp transfers (using tftpd32) over any wan link, no matter how high I set my timeouts and retransmits.

Image upgrade failed

Hello,
We are running RME 3.4.1, when doing an image upgrade we are receiving the following error :
Loading image file to flash device : rep_sw_1054534997912433081 --> flash:c1200-k9w7-tar.123-8.JEC2.tar using TFTP
Loading image file to flash device : rep_sw_1054534997912433081 --> flash:c1200-k9w7-tar.123-8.JEC2.tar using TFTP
Error loading image to flash.
Error Message:
SWIM1125: Failed to copy the image to Flash due to the reason - copyFileOpenError :invalid file name; file not found in partition.
Retry the operation. If the problem persists, check the Bug Toolkit application for any known issues on the running image version.
Is this another bug ?
Many thanks,
Lieven Stubbe
Belgian Railways

What is the current image running on the device? It would be helpful to see a sniffer trace filtering on all traffic between the RME server and the device while the SWIM job runs.

May I use a old photoshop 5.5 bought in 2000 as a base tu upgrade with elements ?

may I use a old photoshop 5.5 bought in 2000 as a base tu upgrade with elements ?

If you go to the Elements product page and click the Buy button you can see what qualifies for upgrading if you select the upgrade option and look at the "I own" list
http://www.adobe.com/products/photoshop-elements.html

Image upgrade for 2811-Error SWIM5004

Hi ,
While doing the image repository of the 2811 routers I am receiving the below error, these errors only appearing when I am doing image upgrade/repository for 2811 routers only.
We cannot use the snmp write due to company policy. If any other solution exist then please advise me.
"SWIM1125: Failed to copy the image to Flash due to the reason - SWIM5004: Cannot initiate SNMP-set operation.
The SNMP Write Community String might be wrong.
Check whether the correct SNMP Write Community String is entered in Device and Credential Repository..
Retry the operation. If the problem persists, check the Bug Toolkit application for any known issues on the running image version.
We are using SNMP v3 and have checked the SNMP settings ,it is ok.
We have also verified that the TFTP service is working properly on the Ciscoworks server.
I am using
LMS:3.2
RME:4.3.1
THANKS

If you cannot use SNMP write access, you will not be able to use SWIM to upgrade this 2811 using TFTP. In order to upgrade the 2800s, RME will perform an SNMP Set of the CISCO-FLASH-MIB to trigger a copy of the image from the RME server to the router. You can use SCP instead in which case the device will be the server. In order to do this, you need to have SSH configured on the device, and the user configured in DCR must be allowed to login to the device with enable level access.

Rescue and Recovery Images. Overwriting BASE Image?

Hi, Ive got a T42 Laptop.
I beleive that I was the first person to have a RnR image created on the laptop which is great.
I created the first and only image on the drive, and as the first image, the RnR program insisted that it be called BASE.
It lives on the hard drive in a hidden partition.
I have to reinstall that image, and when doing so, I'm going to make some updates on it and what I want to do is to save the new image so that if I have to RnR the system again, I won't have to update the computer again with these new updates.
My question is that if I use the RnR to create a new image again can I rename that new image BASE therefore overwriting the old BASE image? I don't want the computer to have multiple backups. I just want one where all the windows updates are complete, and I can start with a blank canvas for everything else.
Much appreciated.

you can't over write it but you can delete it and make a new backup also you can name the backups what ever you want
your version of R&R may look different
Thinkpad R61 7733-1GU
Thinkpad X61T 7762-54U
Thinkpad X60T 6363-4GU
Did a member help you today? Thank them with a Kudo!
If a post answers your question, please mark it as an "Accepted Solution"!
Regards,
GMAC

Difference between LAN BAse Image and Enhanced Image

Can you tell me the difference between switches with LAN Base Image and Switches with Enhabced Image. I want to run HSRP and OSPF on two switches. Can I use LAN Base Image with this or is switches with Enhanced Image.
Many Thanks

The 2960 series does not have an Enhanced Image, just the standard software with and w/o crypto. The 2950 differences can viewed at the following link.
http://www.cisco.com/en/US/products/hw/switches/ps628/prod_bulletin09186a00800b3089.html
HTH and please rate.

Base Image with add-on driver image

Where is the best, latest documentation on how to create a base image and then apply driver specfic images based on the model of the PC? Hardware Dependent Imaging I believe is the correct nomenclature?
Thank you,
Eric

ebolton,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://forums.novell.com/

Animated Gif with large base image & small animated part.

Hello guys
I'm not really sure how to explain that, due to my limited English comprehansion. I will try with images.
I can easily create animated gif out of multiple layers, given each layer is identical, with small changes accuring over time.
But I yet to figure out an animated gif, that uses one large image for the base, and only small part of it is animated.
I always get the animated part working, without the large base applying across all the frames. All it does, is flashes once
the frame is reached and then moves on to being transparent, showing only the small animated part.
For example, this is a GIF made with Galaxy S4, of my friend playing with his phone, imported into PS CS6. On the Galaxy,
after I record the GIF, I can use my finder to touch, mask and freez parts I don't want to move, and leave only small, animated bit.
When I import it to PS, it shows one layer with full image, and bunch of frames with the animation part only.
http://i.imgur.com/UAiopQA.jpg
http://i.imgur.com/7XOGGV6.jpg
Problem is, once the image is open with PS, I'm not able to export it to keep it working in the same manner. Given the Samsung's
gifs are 8 to 10mb, it's hard to edit it, to make it more size friendly.
The gif clearly works the way I describe, so there is a setting or method I don't know about.
If PS is not best tool for editing GIF, what other apps would you recommand I use for it?
Thank you for the taking the time to read
best regards
Monica

This has been an ongoing issue for me since I switched from Powerpoint to Keynote. Most of the animated gifs with transparent backgrounds that I used with Powerpoint are no longer transparent in Keynote. You may want to search for those earlier threads on this topic...
To summarize: I've had to open up my animated gifs in After Effects and use the Color Key effect to restore transparency, with mixed success.
Good luck!

Hierarchy restrictons not working with Basis servicepack upgrade to 14

Hi All,
We recently upgraded our system with basis sp 14, and we having the below problems with out hierarchy restrictions:
Problem #1
We recently upgraded our system from then onwards hierarchy restrictions not working, users are getting authorization error when they execute the query. However we tried by adding aggregates now hierarchy restrictions seems to be working.
Problem #2
We are testing hierarchy restrictions for budget planning function, after we add aggregate its allowing the user to plan the data, but when they try to distribute or escalate the data its again throwing authorization error. When I checked error log for Orgunit hierarchy restriction, the query is looking for single values it is not considering the node restriction, the orgunit values appeared in error log all belong to the node I restricted in analysis authorization.
We implemented note#1133674 as this was relevant to our issue with planning function. But this didnt fix the issue.
We are now on BI SP 16 and Basis SP 14
Just wondering If any of you came across with the same kind of issue, Any help is appreciated.
Thanks,
Kavitha

Hi Kavitha,
Please check SAP note 1229602 Error when using hierarchies: Authorization error.
Regards
Imran

ACS SE base image UPgrade

Similar Messages

Maybe you are looking for