Actiontec GT701C DSL light keeps flashing please help

I use to have the WIFI router from verizon but the wifi range was not strong enough for certain items in my home... in addition the items could not even find the network on wifi. i replaced it with a Actiontec GT701C so i could use my old wireless router that was strong enough to support my whole home .. But know when i connect my DSL line to the New modem the GT701c i can not access the internet .. i Could get to the configure screen but other than that the DSL Light keeps flashing any suggestions.. i have rebooted the modem and tryed diffrent phone line and phone jacks in my home please help !!!

Does your older modem connect still? If so, could you tell us which modem it is so that we could help you obtain the Transceiver Statistics from it? It's possible the ActionTec could either be defective or it could be sensitive to noise on the line if the signal isn't the greatest.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Similar Messages

My MacBook Pro shut itself down and now it won't turn back on and the power light keeps flashing a green and amber but very dull. Help please!

My MacBook Pro shut itself down and now it won't turn back on and the power light keeps flashing the amber light. I don't know what to do, and this has never happened before.

Hello Toby135
Reset the SMC or System Management Controller to resolve issues with the power on your MacBook Pro and power adapter.
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/ht3964
Regards,
-Norm G.

Phone died and I put it on the charger and the red light keeps flashing.

Phone died and I put it on the charger (wall charger) and the red light keeps flashing. It's been doing that for a little less than an hour, I pulled the batttery twice & get the same light flashing. I also read othe posts and it says to just let it charge for a few hours but i don't think it's gonna work. If you know anything about it let me know please & thank you.

When connected to the charger, is the "no battery" symbol showing?
Leave the device to charge 2-3 hours, and then, still connected to the USB cable, remove the the battery from the device a few seconds and reinsert it. If it boots--leave it to charge to 100% (check Options > Status for the percentage). If it doesn't reboot on the first attempt, leave it several more hours. I've had one charge for two days before it came back to life after an extreme battery depletion. Every 3-4 hours, with the device still connected to the charger, you can remove and replace the battery to see if it reboots.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Blackberry LED light keeps flashing red

Yesterday Vodacom Care gave me a new Q5 device - i had a Q5 for 2 months and the phone just went dead - so they replaced it . Now my Q5 LED light keeps flashing red and it's a NEW PHONE ??? - make it stop please !

Hello,
Welcome to the BlackBerry Support Community Forums.
Thanks for the question.
Follow the steps below to try and bring the BlackBerry Q5 back to life:
Ensure that BlackBerry Link is installed on the PC or Mac OS
Ensure the computer has an internet connection.
Launch the BlackBerry Link Software.
Note: A backup of the BlackBerry device should be tried before a reload.
Turn off the BlackBerry device. Make sure there are no flashing LEDs and that the LCD is not still being lit by the backlight. If there are any flashing LEDs, hold the power button for 15 seconds until the LEDs stop.
Connect the BlackBerry device to the computer.
When prompted with Cannot communicate with device, click Restore and then click yes allow the update to be downloaded and installed on the BlackBerry device.
If the restore button is not seen press the vertical dots in the lower right corner of BlackBerry Link and select disconnected device. Highlight the disconnected device you are working with and attempt steps 4 to 6 again.
If the issue still persists, then I suggest contacting your network service provider for repair options.
Let me know if you have any more questions.
Cheers.
VIA | ViciousFerret
http://supportforums.blackberry.com/t5/BlackBerry-Z10/BB-Z10-Died/m-p/2230087#M10125
Please thank those who help you by clicking the button.
If your issue has been solved, please resolve it by marking "Accept as Solution"

Num lock light keeps flashing

Hi,
I have Lenovo 560 and since few days I am observing a strange problem.. The num lock on keypad keeps toggling itself and the num lock light keeps flashing.. ?i dnt know whats the problem is.. any body faced similar problem?
please help.
Thanks,
Rajan

I don't think it is serious enough to return it. I have problems with my num lock and caps lock keys also, but I think it is a problem with the PMU firmware. Quite a few people are having an issue, so I don't think it is a hardware problem.
There are also people having other problems related to the PMU, such as the coloured lines at startup. I suspect we will see a firmware update at some point that can hopefully fix it.
My advice would be try resetting your PRAM with command-option-p-r at startup (until you hear the second chime). Or resetting the PMU by turning off the 'book. disconnecting power and taking battery out, then pressing power button for 5 seconds. Then turn it all back on again and it should be ok.
Stay away from 10.4.7 too, it's just trouble.

Notification light keeps flashing

I've a Nokia N8 and recently the notification light keeps flashing even though i have no messages or missed calls. It only flashes when i lock it and it's not the same flash as a message notification it's more softer. Anyone know how i can stop it or have any ideas why it's flashing?

In the notification settings turn standby breathing light off,this is just to let yet know your phone is on.
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Amber Light keeps flashing - can't configure my AirPort Express

Here is my setup: Dell XPS M1530 running Windows Vista. I have my cable modem directly plugged into my AirPort Express. I have no other wireless network or router.
I'm able to connect to the AirPort Express through my wireless card and establish a connection and surf the net but the Airport Utility Software won't let me configure the device and the light keeps flashing amber. It never turns to green. I've tried every combination of resetting my AirPort Express, cable modem and computer.
I can see the AirPort Express Base Station icon on the left hand side of the AirPort utility software , when I click "manual setup" or "continue" it try to detect a wireless device but it always comes back with a the message: "An error occurred while trying to access the Apple wireless device. Make sure your network connection is valid and try again. error -4"
Am I missing something?

Temporarily, disconnect the ethernet cable from the Express that is coming from the modem.
Connect an ethernet cable from your computer to the AirPort Express, turn off wireless on the computer, and see if AirPort Utility can access the settings that way. If so, go ahead and set it up.
If you are able to configure the device, then you will get an error message that you do not have an internet connection...because the Express is not connected to the modem.
When you re-connect the ethernet cable from the modem to the Express and restart both the modem and Express, you should get the green light.
Depending on the type of modem you have, some additional configuration may be needed. The important thing at this point is to get AirPort Utility to access the settings on the Express so that you can configure it.
You may need to do the factory reset again on the Express. If AirPort Utility still cannot access the settings on the Express after this, try another computer, Mac if possible, to see if that might be the issue.
Sometimes, an internal component fails within the Express. When this occurs, AirPort Utility cannot access the device no matter what, and there are really no other options except to replace the device.
Please post back on your progress.

My Time Capsule doesn't want to (hard nor soft) reset, and the status light keeps flashing quickly.

About two weeks ago, my Time Capsule's status light was flashing rapidly orange/green simultaneously.
Unplugging the power supply worked.
However, now this trick doesn't work anymore, and a soft nor hard reset of the Time Capsule doesn't work either.
The Time Capsule can't reset anymore, doesn't send out WiFi-signals, and its status light keeps flashing rapidly green/orange simultaneously.
Thanks for your support.
Zander.

What model is the TC? Please give the number from the base, A1xxx.
It sounds like the reset has been forced in and is not releasing. I think whatever the problem is you will have a hard time fixing it.. it will need replacement .. it is just a question of what is possible and that depends on its age and model.

Officejet pro 8000 and the power and resume lights keep flashing

I have an officejet pro 8000 and the power and resume lights keep flashing. I initially had the problem when I put a new black ink cartridge in. Lately there was an error message on the computer saying pump stall error, which then culminated in a print head error. I have replaced the print head at an extra £40 I have replaced all the ink cartridges which say they are low even though I haven't been printing. Basically spent the cost of the printer again AND I STILL CANT PRINT! I'm using a Mac with snow leopard and I have reset the printer list and installed the new software and drivers. I have tried connecting with USB and Ethernet. I have filled up the paper. I have taken out the duplex and given it all a blow through. reset the print heads - basically everything the support web pages told me to do.
I have to say this is the worse printer I have ever had from HP. I always buy HP because of the quality. I have to say I feel unless this problem is solved with out me spending more money on it I will have to buy something else - and not HP ever! oh and the warranty is out by less than 2 months!

Welcome back burtf,
I am sorry to hear about the issue you are having with your Officejet 8500 showing a message for you to turn the printer off and on. I would recommend following the guide below for this issue.
I hope it helps!
'Turn Power Off then On' Message Displays on the Control Panel
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions: click here.
Happy Thursday
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

HT1267 I have a big problem regarding my iphone4 it wont start up and it keeps vibrating, please help me fix it. its been vibrating since 2 pm until now 7pm here in Philippines :(

I have a big problem regarding my iphone4 it wont start up and it keeps vibrating, please help me fix it. its been vibrating since 2 pm until now 7pm here in Philippines

What program did you use to fix the internal hard drive? What repairs did it report making? More crucially, if repairs were reported, did you re-run the utility until it reported no problems found? It's possible for one set of problems with a drive to mask others.
If you have about 5GB or so free space on the internal hard drive, you can use your OS X Install disc to perform an Archive and Install to recover from the failed Software Update. When the computer restarts, download and run the OS X Update Combo 10.4.11 (Universal). When the Mac restarts after that, run Software Update. During all this, make sure nothing interrupts or shuts down the Mac! Note that the first start after each of these updates will take significantly longer than subsequent starts, so be very patient.
How did you back up your internal drive to the external one? Did you just drag things over in the Finder, or did you use a utility such as SuperDuper! or CarbonCopyCloner? Does the external HD show up as a bootable volume in System Preferences > Startup Disk, or using Startup Manager?

Light keeps flashing and cannot connect to ipad

The front light keeps flashing and there is no connection to my ipad - advice seems to be to restore but do I restore on the ipad - general settings and restore

Welcome to the Apple Community.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source List
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Devices list, and then click Restore.
(You may already have a micro USB cable if you have a camera or other digital device)

I am connected to the internet, but the amber light keeps flashing. What is wrong?

What is wrong with my Airport express when the amber light keeps flashing, even though I am connected to the internet?

The AirPort Express has a message for you.
To find out what it is......
Open AirPort Utility, select the Express, click Manual Setup
Click directly on the word Status (3rd line)
A window will open with details about why the Express is complaining.

Help, Amber light keeps flashing

Please help. I just purchased an airport express. I plugged it in just for use with my stereo. I already have a wireless router. Airport Utility was unable to recognize my airport. Is it broken or what is wrong. Please email to [email protected]

Hello and Welcome to Apple Discussions ...
What if my base station is connected to a router?
If your base station is connected to a router or other network device that is using NAT to share a single Internet connection with multiple computers on your network, and you are using DHCP to provide private IP addresses, you need to turn off NAT and DHCP on the AirPort base station.
Most networks need only one device using NAT and DHCP to provide IP addresses.
To turn off NAT and DHCP:
Open AirPort Admin Utility, select your base station, and click Configure.
Click Network and deselect the "Distribute IP addresses" checkbox.
If your base station supports Power over Ethernet (PoE), by default the "Distribute IP addresses" checkbox is not selected, and the base station is not using NAT or DHCP.
With NAT and DHCP turned off, the base station acts as a simple bridge between the wired and wireless computers on the network.
Carolyn

How long Q10 LED notification light keep flashing ?

My Q10 LED notification light will begin flashing when a Call , E-mail or any comes in, but after a about 15 minutes it stops flashing. My previous is 9700, its LED keep flashing until you read or checked at the notification. Because this helpfull when we wait for important e-mail or event you can E-mail come in after you leave your phone for a while. I have tried tap the top button for 30 second, I think it not the way and not work for me. So I am wondering, how long is the LED supposed to keep flashing on the Q10? and is this normal ?
Solved!
Go to Solution.

The LED on all BB devices has always timed out after about 15 minutes or so. I had the 9700 and it timed out for me, as well, so I'm not sure why you say it was any different on the 9700.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

Another person who has a problem with Flash - Please Help!!

I have a Dell Dimension 4700 Intel (R) Pentium (R) - 4 CPU 2.80 GHz 2.79 GHz 504 MB of RAM
For a few years now I would have to restore the computer to an earlier time after an update was done in order to view youtube, etc. It seemed that when my computer did an automatic update it would mess up the flash player.
My husband just recently did another update and now the flash isn't working and the computer won't restore anymore.
I keep getting the following messages: adobe flash player active x set up failed to install 19166
program error: failed to register status installation complete
I have uninstalled and installed the flash several times
everytime i go to install flash it says: Adobe Flash Player 10: This application has been downloaded before. Reload?
Then I get: Your security settings do not allow websites to use ActiveX controls installed on your computer.
I don't want to take this somewhere because I have a feeling that will just wipe the computer clean and I have a feeling it is something stupid that I'm not doing.
Please Help.

OK...Check, check...did all that. I am cutting and pasting a segment from the flash troubleshooting page because its exactly what is happening to me. There were no responses to help this person.
"I've tried installing flash player 9 but am not able to do so. It will begin installing but when it gets to 'items remaining: 4' the progress bar continues to move and underneath says searching but nothing happens. I tried leaving it on all night but same thing when I came back in the morning. When I close the installer it then says 'stopping now may result in an incomplete set of software' Also, when I tried uninstalling previous versions, the uninstaller does nothing. It says 'items uninstalled: 0' and 'processing', but same thing, the thing spins but nothing happens. i tried the other steps given to see if that helped but nothing seems to work."
Here is the page...
http://sdc.shockwave.com/cfusion/webforums/forum/messageview.cfm?forumid=44&cati d=184&threadid=1267248&enterthread=y#4577694
I tried some of the suggestions above the last two posts. But it looks like my problem is the same as those.
I even tried to post on there but from what I see it looks like I have to have flash to do it...I get the page with the blue lego brick.
I'm pulling my hair out. I didn't realize how much of the internet ran on flash.

Actiontec GT701C DSL light keeps flashing please help

Similar Messages

Maybe you are looking for