Actiontec GT704GS how do I configure QoS???

I just got a new Actiontrec GT704GS router/modem from Verizon and the documentation has virtually zero beginner information about how to configure QoS. I use a Skype enabled phone with a static IP so it souldn't be too hard to set up.
The manual says to "enter appropriate value..." like I should just know what that is!

I have the Westell 7500 and have encountered the same problem with trying to set up the QoS settings. It assumes you know what they should be, no suggestions, etc. Maybe you will have some luck. I've opened up a post requesting the same for the Westell 7500. Maybe there is some similarity between them. Mine's a gateway also.
As a temporary work-a-round, I've bridged a Netgear router off of the gateway, turning it into just a DSL modem. The Netgear router's settings for QoS are much more intuitive to set up.

Similar Messages

  • How to configure QOS on certain IP in the Cisco ASA 5510

    Hi,
    I am need to configure QOS on certain IP in the Cisco ASA 5510. Assume the IP's are 10.0.1.5 , 10.0.1.6 , 10.0.1.7. Here i have to configure 512 KBPS for 10.0.1.5 and 2 MBPS for 10.0.1.6 and 10.0.1.7
    Can this done on a ASA 5510 series? if yes can you help me how ?
    Regards,
    Venkat

    Yes you can do it.You can match the ip addresses in an access-list, put in a class-map and the class-map in a policy map that will do policing.
    Good examples for what you want to do are here https://supportforums.cisco.com/docs/DOC-1230
    I hope it helps.
    PK

  • How to enable auto QoS on C4500-X

    How to enable auto QoS on C4500-X for Cisco phone? Since it is different from the global commands 'mls qos',who has the example? Thanks.

    http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/20ew/configuration/guide/macro.html
    Take a look at this document
    And this one
    http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/prod_white_paper0900aecd8041691c.html

  • Air Bridge 1310 - Configuring QOS on Point to Point

    I have 2 BR1310 Air Bridge's configured for a point to point connection, one is root,one is non-root. In configuring QOS for VOIP for the first time, I'm looking for a best practice configuration.
    Behind each bridge is a 3560 switch that has QOS configured on each switchport. Our environment consists of 7960 desk phones.

    Hi Michael,
    Have a look at these docs. Hopefully they will help get you started;
    Cisco Aironet 1300 Series Outdoor Access Point/Bridge Software Configuration Guide, 12.3(4) JA
    Chapter 14 - Configuring QoS
    This chapter describes how to configure quality of service (QoS) on your access point/bridge. With this feature, you can provide preferential treatment to certain traffic at the expense of others. Without QoS, the access point/bridge offers best-effort service to each packet, regardless of the packet contents or size. It sends the packets without any assurance of reliability, delay bounds, or throughput.
    From this doc;
    http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.3_4_JA/configuration/guide/o13qos.html
    Giving Priority to Voice Traffic
    This section demonstrates how you can apply a QoS policy to your wireless network's voice VLAN to give priority to wireless phone traffic.
    In this example, the network administrator creates a policy named voice_policy that applies voice class of service to traffic from Spectralink phones (protocol 119 packets). The user applies the voice_policy to the incoming and outgoing radio ports and to the outgoing Ethernet port for VLAN 77.
    Use the Apply Policies to Interface/VLANs drop-down menus to apply policies to the access point Ethernet and radio ports. If VLANs are configured on the access point, drop-down menus for each VLANs' virtual ports appear in this section. If VLANs are not configured on the access point, drop-down menus for each interface appear.
    From this doc;
    http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.3_4_JA/configuration/guide/o13qos.html#wp1047736
    Hope this helps!
    Rob

  • Configuring QoS in ME 3400

    I have to change of platform of one switch 3550 to and switch ME 3400.
    I have to adapt the QoS configuration of the switches 3550 to the new switches ME 3400.
    This is the QoS configuration of the 3550 :
    mls qos map cos-dscp 10 15 20 25 30 35 40 45
    mls qos
    interface FastEthernet0/X
    mls qos cos 4
    mls qos trust cos
    wrr-queue bandwidth 1 2 3 4
    This is the QoS configuration that I have done in ME 3400:
    Is this configuration ok?
    Class Map match-all COS7
    Match cos 7
    Class Map match-all COS6
    Match cos 6
    Class Map match-all COS5
    Match cos 5
    Class Map match-all COS4
    Match cos 4
    Class Map match-all COS3
    Match cos 3
    Class Map match-all COS2
    Match cos 2
    Class Map match-all COS1
    Match cos 1
    Class Map match-all COS0
    Match cos 0
    Class Map match-any VLAN
    Match vlan 1-4094
    policy-map MARCADO_ENTRADA
    Class VLAN
    service-policy MARCADO
    Class class-default
    policy-map MARCADO
    Class COS1
    set dscp 15
    Class COS0
    set dscp af11
    set cos 4
    Class COS2
    set dscp af22
    Class COS3
    set dscp 25
    Class COS4
    set dscp af33
    Class COS5
    set dscp 35
    Class COS6
    set dscp cs5
    Class COS7
    set dscp 45
    interface FastEthernet0/1
    description # Conex ANILLO con 3400_1
    port-type nni
    switchport mode trunk
    logging event spanning-tree
    logging event status
    storm-control broadcast level 0.50
    storm-control multicast level 0.50
    storm-control action trap
    no cdp enable
    service-policy input MARCADO_ENTRADA
    ip dhcp snooping trust
    end
    I only can apply the service-policy in trunk ports.
    How Can I configure a service-policy in a access-port?
    When I apply the service-policy input in the fa0/1 and I send traffic I can't see any COS traffic.
    Could you help me to configure this??
    Why I can see traffic in the interface?
    SW_3400_2#sh policy-map interface fa0/1
    FastEthernet0/1
    Service-policy input: MARCADO_ENTRADA
    Class-map: VLAN (match-any)
    0 packets
    Match: vlan 1-4094
    Service-policy : MARCADO
    Class-map: COS1 (match-all)
    0 packets
    Match: cos 1
    Set dscp 15
    Class-map: COS0 (match-all)
    0 packets
    Match: cos 0
    Set dscp af11
    Set cos 4
    Class-map: COS2 (match-all)
    0 packets
    Match: cos 2
    Set dscp af22
    Class-map: COS3 (match-all)
    0 packets
    Match: cos 3
    Set dscp 25
    Class-map: COS4 (match-all)
    0 packets
    Match: cos 4
    Set dscp af33
    Class-map: COS5 (match-all)
    0 packets
    Match: cos 5
    Set dscp 35
    Class-map: COS6 (match-all)
    0 packets
    Match: cos 6
    Set dscp cs5
    Class-map: COS7 (match-all)
    0 packets
    Match: cos 7
    Set dscp 45
    Class-map: class-default (match-any)
    0 packets, 0 bytes
    5 minute offered rate 0 bps, drop rate 0 bps
    Match: any
    Class-map: class-default (match-any)
    0 packets, 0 bytes
    5 minute offered rate 0 bps, drop rate 0 bps
    Match: any
    SW_3400_2#
    Regards,
    Lorena García

    According to documentation, it does.
    http://www.cisco.com/en/US/partner/docs/switches/metro/me3400/software/release/12.2_25_seg_seg1/configuration/guide/swoam.html#wpmkr1087893
    But only PE-Side of it.

  • Need help with configuring QoS

    Hello,
    We are in the process of implementing MPLS for our WAN links so that we can run VoIP between 9 locations in the USA and I have lots of questions regarding how to configure QoS.
    We have a dedicated E1 connection to our headquarters in Germany. This location houses all of our SAP servers.
    In each location in the US, we will be using Avaya IP telephones and media gateways for voice communications. We also have some Polycom units in the field for video confererncing.
    How would I begin to configure QoS for these network connections.
    I was planning on using IP precedence or DSCP for marking the traffic and prioritizing as follows.
    Highest Priority: Voice and video
    2nd Highest: SAP and Oracle traffic
    Default priority: Lotus notes, www access
    Here are some questions that I have:
    1- For voice/video, which DSCP values or IP precedence values do I use?
    2- How do I assign voice/video to the LLQ queue?
    3- For SAP, what is the best way to mark the SAP traffic? From my understanding, SAP uses a variety of ports.
    4- For SAP and Oracle, should I use the CBWFQ queus? Is that preferable over other queues for this traffic?
    5- Should I make another classification of traffic for things like signaling for Voice and TFTP/FTP?
    6- If so for #5, what IP precedence/DSCP value(s) should I use and which queuing mechanism should I use?
    Thanks for the help in advance. At this point, you can probably tell that I am a newbie to QoS.
    Pete

    I can answer a few since i have a ton of avaya ip phones deployed.
    1)personally i leave both bearer and signaling in same queue at 46 (Diffserv) and 5 (COS) Video would be 40/4.
    2)sample config:
    class-map match-all voip-fr
    match ip dscp 46 (all traffic that have DSCP 46)
    class-map match-all vovid-fr
    match ip dscp 40(all traffic that have DSCP 40)
    policy-map llq
    class voip-fr
    priority 100 (Reserve 100Kbps priority bw for DSCP 46)
    class vovid-fr
    bandwidth 300 (Reserve 300Kbps non-priority bw for DSCP 40)
    class class-default
    fair-queue
    Serial Interface 0/0
    service-policy output llq (Apply policy map to voice and signaling
    traffic)
    5) nope. leave tftp and data in the default queue
    Also, since you are deploying Avaya IPT make sure you look at this document. great document i used.
    http://support.avaya.com/elmodocs2/comm_mgr/r3_1/pdfs/245600_4_2.pdf

  • How do I configure the Airport utility to allow more than one rule per port?

    How do I configure the Airport Utility (AU) to allow more than one rule per port?
    I am on a home network, with broadband cable modem.  I have my airport extreme connected to the broadband modem.  I have 2 servers in my home that need to be accessed remotely from time (SSH), and they also serve data for an iphone app, so I'm using a variety of protocols.  The problem I'm running into is that AU seems to only allow one rule per protocol, so if I go to add another address for access on a specific port that is being used by one of my servers, AU tells me "The Port Mapping Entry Already Exists". 
    I need to be able to allow SSH on both of my servers, for instance.  Am I missing something?  Is this doable with AU?
    Thanks for any insight.
    Khalid

    The Port Mapping "rules" on the AirPorts will allow you to: 1. Map a single port to a single IP address OR 2) Map multiple ports to a single IP address.
    What you won't be able to do is map a single or multiple ports to multiple IP addresses.

  • How do i configure the usb port on a draytek vigor 2820n router for use with my imac

    i have an imac connected to the internet through a draytek vigor 2820n router. this router has a USB port with a HP Deskjet 5560 printer attached (for use as a network printer for other machines on the network). How do I configure this printer on the iMAC?

    I checked on the HP web site. Your aswer is on the HP website under your printer type. Update your drivers and follow the instructions given by HP and the printer will work as you have it connected.
    Good Luck

  • Fedora 13: After upgrading from FF3.6 to FF6.0.2 I no longer have a Java plugin. How do I configure the Java Plugin for FF 6 ? There is no Java Plugin at the site

    I am Fedora 13x64 bit. I just installed FF v6.0.2 from the FF download site. I backed up the existing FF 3.6 as firefox_old
    I need to have a Java plugin to access company site, how do I configure the Java Plugin ?
    At the Plugin area in FF6 there is no Java Plugin available, even after a search.
    I have Java 1.6.0 installed in the OS at:
    /usr/lib/jvm/java-1.6.0/jre/lib/amd64/libnpjp2.so
    I googled how to configure Java Plugin for FF 6 for Fedora 13 and the trick was to create a soft link from /home/<userID>/.mozilla/plugins to the above libnpjp2.so

    AVtech wrote:
    . . . If a person can't get an answer here I don't know where else to turn since Sun certainly wouldn't offer tech support for a free product . . .These forums are user forums, and only occasionally visited by Sun employees. Sun does provide Java technical support options, although (of course) at a charge.
    See:
    http://developers.sun.com/services/
    . . . I guess we'll just use JRE 5 until it's unsupported, whenever that will be. I'm still waiting for an answer on that question, too. See:
    http://java.sun.com/products/archive/eol.policy.html
    http://www.sun.com/service/eosl/
    This document (part IV and Appendix) has some debugging and troubleshooting information that may allow someone involved in the problem to resolve the cause:
    See:
    http://java.sun.com/javase/6/docs/technotes/guides/plugin/developer_guide/contents.htm
    Any steps that you can take to isolate the problem to specific Java versions, browsers, applets, web sites, operating systems (and versions), etc, would enhance the possibility of getting help.
    You can try the applets at this Sun location and see if any of them are "slow".
    See:
    http://java.sun.com/javase/6/docs/technotes/samples/demos.html

  • How do you configure a farm name in RDS 2012?

    I understand Remote Desktop Services has undergo some drastric changes.
    How do you configure a farm name in RDS 2012? Or is the concept around farm name changed in another concept?
    Although I have imported a certificate on the RDCH withe the farm name I want to use. When I click on a RemoteApp on the RD Web Access portal, it does not connect to the right farm name.
    Boudewijn Plomp, BPMi Infrastructure & Security

    You don't.  You create a collection.  A client connects to the Connection Broker and then is redirected to the collection it is connecting to.  The collection name is embedded in the connection file that the client downloads from RDWeb or
    the RDWeb feed. 
    A collection is basically at least one RDSH server (for session based desktops) or one virtual machine (virtual machine based desktops). 
    Don Geddes - SR Support Escalation Engineer - Remote Desktop Services - Printing and Imaging

  • How do I configure my Airport Extreme to see the printer I have plugged into the USB port?

    How do I configure my Airport Extreme to see the printer I have plugged into the USB port?

    OK. The 6.0 version no longer has a printer configuration that I could find. You might try Printer Sharing in the Sharing preferences.
    I would also check the printer's user manual for help with the setup, and that failing check the manufacturer's website and/or tech support.

  • HT4623 please help!! how can i configure my iphone 3gs because i've been updated a new version i did it but it's hard to activate it again.

    please help!! how can i configure my iphone 3gs because i've been updated a new version, i did it but it's hard to activate it again. this message i always recieved in my iphone
    "We're sorry, we are unable to continue with your activation at this time."

    You phone was hacked. You can not get help with it here. Hacking / Jailbreaking voids any warraty and forfeits your right to support. Discussing jailbroken / hacked devices is forbidden by the terms of service here.

  • HT3382 I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter.  How do I configure the computer so that it doesn't sleep when I close the lid of the computer.

    I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter.  How do I configure the computer so that it doesn't sleep when I close the lid of the computer.

    Hi alangium,
    Welcome to the Support Communities!
    Resetting your computer's PRAM should restore your Macbook Pro's screen appearance.
    OS X Mavericks: Reset your computer’s PRAM
    http://support.apple.com/kb/ph14222
    This article may provide some information about your Mini DisplayPort to AVI adapter.  Have you tried to connect a different VGA monitor to your Macbook to see if you get the same results?
    Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
    http://support.apple.com/kb/HT3382
    18. What is the maximum resolution available for use with the Apple Mini DisplayPort to VGA adapter?
    The resolution available with the Apple Mini DisplayPort to VGA Adapter is 1920 x 1200. VGA displays that use higher refresh rates (such as 85 Hz) at resolutions of 1600 x 1200 or greater may not generate video properly until you lower the refresh rate.
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/HT1573#5
    How can I detect displays?
    If the detect displays option is not available, hold down the Option key while you are in the Display pane.
    How do I select additional resolutions on my display?
    You can use the Display pane of System Preferences to specify how your display works. Not all options appear for all display models. By default the best resolution for your display will already be selected in System Preferences.
    To select a different resolution, use the Scaled option. Some additional resolutions may be available when you hold the Option button.
    I hope this information helps ....
    - Judy

  • How can I configure iCloud so it doesn't restore deleted or moved emails on my Mac?

    I moved to iCloud, and so far it looks like everything is where it's supposed to be. My question is about syncing. When I delete an email on my Mac, iCloud restores it. How can I configure iCloud so that changes I make on my Mac and my iPhone stay changed?

    On the Mac in System Preferences > iCloud
    Make sure Mail & Notes is selected.
    ON the iPhone tap Settings > iCloud
    Make sure Mail is switched on.
    And try restarting your Mac and iPhone.

  • How do I configure DW to open and load a file?

    I have DreamWeaver CS5 running on a Mac. Whenever I double-click to open a DreamWeaver compatible file (such as an HTML file), if DW is not already open, DW launches but does not load the file. Once DW is launced, I can double-click the file and it will load. How do I configure DW to open and load a file together?
    DW: v11 b 4993
    OS X: 10.7.4 (11E53)

    HTML files are normally configured to open in a browser. The default on a Mac is to open the file in Safari.
    You can right-click the filename in the Mac Finder, and select Open With > Dreamweaver CS5 from the context menu.
    Alternatively, select an HTML file in Mac Finder, and press Cmd+I to open the Info panel. In the Open With section, select Dreamweaver CS5 as the default program, and click the Change All button.

Maybe you are looking for