Actiontec MI424-WR web interface not responding properly

The web interface of my Actiontec MI424-WR rev c router, with firmware v 4.0.16.1.56.0.10.12.3, is not responding properly when I try to access it to configure the router or read the logs. It sometimes takes a very long time to respond, and my browser will say that "the connection to the server was reset". Has anyone else had this problem?
ps
I neglected to mention, it just started doing this recently, probably within the last two weeks or so, it was fine before.

annonymous009 wrote:
The web interface of my Actiontec MI424-WR rev c router, with firmware v 4.0.16.1.56.0.10.12.3, is not responding properly when I try to access it to configure the router or read the logs. It sometimes takes a very long time to respond, and my browser will say that "the connection to the server was reset". Has anyone else had this problem?
ps
I neglected to mention, it just started doing this recently, probably within the last two weeks or so, it was fine before.
Connecting to it it wirelessly or via cat5?
If wirelessly does the same occur if you connect hard wired.?
Any other routers on your LAN?
Any new wireless devices, phones etc, added recently?

Similar Messages

Ix2 web interface not responding

I have the EMC IX2 200. I can no longer connect to the web interface. I recently had to replace a failed drive, I used the same model and size. Afterwards the mirror repaired itself but I could never manage the storage. Some message about the drives. The drive status showed fine in the mgmt interface. I downloaded firmware updates but it would not allow me to install. I tried rebooting the device but it never completed, even after waiting for than a day. It wouldn't respond to pings so I unplugged it the powered it back up. Now the web interface never comes back up. I can access my existing shares but I can't manage the device via the web interface. No service is listening on ports 80 or 443. I did have ssh enabled so I can access the system via a shell. Apparenty this is a common problem for which no known solution exists judging from numerous other forums. After rebooting all lights appear normal other than the white exclamation light keeps blinking. I've already spent many days on this issue but haven't given up on this product yet. Any suggestions?
[Port scan]
Scanning 192.168.1.15 [1000 ports]
Discovered open port 22/tcp on 192.168.1.15
Discovered open port 21/tcp on 192.168.1.15
Discovered open port 139/tcp on 192.168.1.15
Discovered open port 445/tcp on 192.168.1.15
Discovered open port 9000/tcp on 192.168.1.15
Discovered open port 873/tcp on 192.168.1.15
Discovered open port 49152/tcp on 192.168.1.15
Discovered open port 631/tcp on 192.168.1.15
Discovered open port 548/tcp on 192.168.1.15
Discovered open port 3689/tcp on 192.168.1.15

Yes, I'm not sure what is up with their tech support. I think they inherited a somewhat underwhelming product that had unrealized potential. I think it suffers from too much compromise on hardware for what they were trying to accomplish in software. It is somewhat maddening that they refused to use ssh to diagnose the problem. That is why it exists. I had it enabled when i first acquired this product to fix an issue at tech support's request. It appears everything booted up but something is wrong with the appweb service. The service is running but doesn't respond to connection attempts on 80 or 443. It isn't listening on the web ports. I still haven't heard back from their escalated support team. I wonder if it really exists? I've seen many other forums where a support issue got stuck here. The storage problem has worsened. I was copying all my data off when, in the middle, the share quit responding. The box would not power down, reboot or reset. I tried pulling power but still could not access the main share when it came back up where most my critical data resides. I connected in with ssh and traversed the directory tree, the base folder is there where the share would be advertised, but all the data is gone! I didn't get anywhere near a full copy completed. There are some other minor shares I had created and they still work, but I still cannot access the box via the appweb service, even though the process is running. Fortunately I can recover most my important data because I was also backing it up with Crash Plan (thank god!) but this will be very time consuming. I can't even begin to express how frustrating this process has been, not to mention the countless hours trouble shooting. Long story short, I wouldn't trust any important data on this device. I've ordered a Synology DS213j with two 3TB Western Digital RED drives to replace this. If I can get the ix2 repaired I will only use it for lab unless someone wants to buy it off me. -- thanks, David

WRT54G v6 Web Interface Not Loading Properly

I just bought a WRT54G v6 router. When I tried to configure it via the web interface at 192.168.1.1, the web page came up, but only partially. None of the links were visible. After reading other posts, I tried upgrading to the latest firmware WRT54Gv5v6_v1.02.2_fw.bin via the Management Mode because the normal web mode wasn't accessible. The upgrade appeared to work, but the following screen was blank instead of saying "Upgrade Success". I cycled power. The normal web page showed the new firmware version number, but the page still was missing its links. I tried the upgrade procedure again with the same results.
I downloaded the EasyLink Adviser and let it configure the router. It appears to have been successful. However, I tried the web interface afterwards, and the page is still not showing the links properly.
Is my web interface issue an indication of future troubles with the router? Is there any way to get the interface to work properly?
I have tried the web interface with both IE and FireFox, and with my firewall/antivirus software turned off. The Cisco logo indicator is the normal solid amber. The power light is solid on. The WLAN/1/Internet indicators are on and blink with net traffic. I cannot find any other indicators of router trauma other than the web interface.

Hi there, Lumen!
Have you tried resetting the router?
At the back panel of the router, you'll find a reset button on it. Press on it for 30 seconds while the router is on. After doing so, you could let go of the reset button and then take out the router's power cord for like ten seconds and plug it's cord back it. After that time, check if you'll have the proper lights on the router again and see if you'll be able to see the whole router's setup page this time.

Safari - "web pages not responding" about once an hour. I'm about to switch to Chrome if I can't fix this.

Safari - "web pages not responding" about once an hour. I'm about to switch to Chrome if I can't fix this. Help?

Regarding #1, your post says you have a beta version of Firefox 4. That may well be incorrect, but that is why the site says you do not have the latest version.
Losing graphics on the bookmarks toolbar and not having a working back button are not normal, but I'm not sure whether you want to troubleshoot Firefox 4, roll back to Firefox 3.6, or just move on.
How can we help?

Web service not responding

Hi,
Issue - Web service not responding when we deploye the .ear file in prod instance. Same web service working fine in test instance.
We are using Oracle Enterprise Manager 10g server.
It is urgent for us.
Thanks,

If it is urgent, call support. Besides, this is the wrong forum as this is for Sun Application Server related issues.

My trackpad is not responding properly on MacBook Pro. Can move the cursor but not click on icons or similar items.

My trackpad is not responding properly on MacBook Pro. Can move the cursor but not click on icons or similar items.

Intel-based Apple Portables: Troubleshooting unresponsive trackpad issues

The start/stop bar on my i Tunes app does not respond properly. Please advise.

The start/sop bar on my i Tunes app does not respond properly. Please help.

It can be that the library path, or files, are corrupted. What happens if you set a different path to save the library?

Public Interface not responding after second node is started in the cluster

Hi
Has anyone ever experienced the public interface not responding between nodes in the cluster (ping, ssh, scp) after the second nodeapps is started in the cluster?
This is a new install so all I have installed so far is the base release of CRS 10.2.0. This is on Solaris10. The vipca failed during the installation, however I was able to proceed and manually add the nodeapps using srvctl add nodeaps -n -o -A.
It seems after the second node is started I loose all connectivity to the public interfaces and to my default gateway.
Also I'm getting the following messages sometimes after I try and stop the nodeapps and start them back up.
CRS-1006: No more members to consider
CRS-0215: Could not start resource 'ora.node1.vip'.
Any suggestions on where I should start troubleshooting?
Thanks

Do you have default GW?
It can connects with GW, can't it?
Check metalink
CRS-0215: Could not start resource 'ora..vip' [ID 356535.1]
CRS-1006: No more members to consider when starting service [ID 465364.1]
Good Luck

SMTP not responding properly

Hello,
I am running iMS 5.1 with bundled directory services 4.1 on a win2k.
yesterday there was a power failure and the server went for an abnormal reboot. Since then my iMS is not responding properly.
I am able to connect to port 25 but then after that theer is no respose from the server, it just hangs at that.
Even when I try to dirsync -F it will just not complete and will stay there.
What do I do now?
Pls help I am in a dire situation.
Regards,
Sanvir Jham

Thanks for the hint.
I finally managed to remove the dirsync.lock. __db_lock.share and __db_mpool.share from <server-root>/imta/tmp/ after making the iplanet services manual and then restarting the win2k server.
After removing these lock files, I again switched my iplanet services to automatic and restarted the machine.
Now the server sings :)
Thanks for replying,
S.

CIMC Web/SSH interface not responding

Can the CIMC Web/SSH interface be reset without power cycling the whole server?
We have two C460 M2 Rack mount servers using a dedicated CIMC. Standalone (not UCS manger enabled). The server is running fine and I can ping the managment IP fine. The Web interface times out and SSH connects but presents no CLI #.
The documentation for this server indicates that the front panel has a 'Reset Button' and an 'NMI Button' The documentation however lacks any description of what it resets or even what NMI is.
Thanks in advance for you replies.

Hi,
Unfortunately, the ways you can reset CIMC without touching the rest of the server involve a connection to CIMC itself through either SSH or HTTP(s). There is an OLD known issue with the old models (M3s do nt suffer this, at least I have not seen it) where you need to reboot the server to recover access.
-Kenny

Lately pdf files from the Web do not display properly; what is wrong and how can I fix it so I don't have to use IE?

I am a professor and frequently need to open pdfs of academic journal articles from electronic databases. Within the last two or three weeks, when I try to do this using Firefox, only the first page of the pdf displays and the rest are blank. In addition, a bar appears across the top with the message "This pdf file may not display properly." So I have had to switch to Internet Explorer to open the files and do my research. What is going on and how can I fix it so I can open pdf files from the Web in Firefox and have them display properly?

My question is simple - why would you put an application in production that has a lot of bugs? To replace a good and steady Adobe product? My customers will believe that I put a pathetic fallible form online. They are not sophisticated on computers so I just tell them to use IE. Ugh
I must agree with pgwebgirl!

Laserjet 4345 mfp won't scan to folder; web interface not showing all admin tabs

Hi,
I have a laserjet 4345 mfp which, until a few days ago, was able to scan documents to a network folder. When I try now it gives me the error "the path cannot be found". Here's what I've tried so far:
- Looked for a way to change the network folder settings or define a new folder. I couldn't find any so I printed the "how to scan to folder" page from the control panel. It tells me to define a new location by clicking the "Other" button on the control panel, but I can't find an Other button, on any screen.
- Accessed the web interface, which only shows up with the "Home" and "Networking" tabs - no "Digital Sending", "Settings", or "Information" tabs, which should be there according to the manual.
- Thinking it might be a permissions issue, I checked and found that the administrator password was not set. I set the admin password via the web interface, and now when I try to access it prompts for the password I defined, but still gives this incomplete interface. I am also able to access and change all the networking settings, so I don't think insufficient permissions are the issue.
- Called HP support, they said the problem is permissions and I should cold reset the machine, which I am quite reluctant to do since not only all settings, but the entire address book as well, would need to be re-entered. This aside from the fact that I really don't think permissions are the issue, as decribed above.
- Verified that I am able to send scans to different email addresses. SMTP gateway test goes through OK. LDAP does not, but this has not prevented scan to folder from working in the past.
I don't know how the scan-to folder was initially set up because I wasn't supporting this client at the time.
Any ideas?
Many thanks in advance.

I have a problem with my scan to folder as well and I have to access the folder from a computer before it will work. I'm not sure why that works, actually. You might want to give that a try to see if it fixes the problem. If it does, I imagine it is some sort of security problem with the folder you are trying to scan to.
Thanks,
Tiffany
I am an HP employee!

Gasbuddy web site not working properly with firefox, but working fine with explorer

I've noticed when I load the web site gasbuddy.com, it is not working properly. It does load, just not performing like it should. When I try using gasbuddy.com on explorer 9, it works fine. I've already tried working in safe mode and that didn't solve the problem with gasbudy.com. Any suggestions as to how to fix the problem? I did do some prior investigating, and I'm very cautious about removing my cookies. It seems when I do that procedure, I lose too much info on certain web sites----weather.com, weatherunderground, etc. Just not sure how to remove cookies to solve a problem with out causing other problems? Thank you.

I'm glad we were able to figure it out. Many sites are designed with stretchy columns that work with either full zoom or text-only zoom, but definitely not all of them.

Web pages not displaying properly IE9

Hello,
Using Windows 7 32 Bit enterprise edition and IE9. Web pages are not loading properly but it works fine in Chrome and other browsers. Followed the below steps also. It did not help. Please let me know the other steps.
1. Click Start, type in “inetcpl.cpl” and press Enter.
2. Switch to Advanced tab.
3. Select the Use
software rendering instead of GPU rendering*
4. Check if the issue has been resolved.
5. If not, please Click Reset twice under Advanced tab to reset IE settings.
Regards,
Boopathi S

Hello Robear,
Please find the below answers.
1. When (approx. date) was the Win7 (32-bit) computer purchased?
It is purchased on 11-Auf-2014
2. What is the
full name of the installed anti-virus application or security suite andwhen (approx. date) does the current subscription expire? What anti-spyware applications (other than Defender) are installed? What third-party firewall (if any)?
Microsoft forefront endpoint protection
3. Has a(nother) Norton application
or a McAfee application EVER been installed on the computersince it was purchased?
No. It is reimaged with customized OS
4. Did a Norton free-trial
or a McAfee free-trial [PICK ONE] come preinstalled on the computerwhen it was purchased? (Doesn't matter if it was never used or Activated.)
I do not know
5. Is KB3003057, KB3006226, KB3010788, KB2992611, KB2993958, KB3005607, KB2978120, KB3003743
and/or KB3002885 listed inInstalled Updates (not
Update History)? [1]
All the above mentioned updates are not installed.
6. Is Adobe Flash Player
v15.0.0.223 (or higher) installed? TEST HERE USING INTERNET EXPLORERONLY! =>
http://www.adobe.com/software/flash/about/
Adobe Flash Player 11 ActiveX 11.9.900.117 is installed
7a. When (exact date) was
Internet Explorer 9 installed according toInstalled Updates?
7b. What Update Version & KB number are displayed in the
second line of text in IE9's Help | About [Alt+H+A] tab; e.g.,Update Version: 9.0.54 (KB1231231) ?
7c. Has the
IE10 Blocker Toolkit and/or theIE11
Blocker Toolkit been installed?
No
8. Is Firefox, Chrome or any other alternate browser installed?
No
9. Are you in the habit of using "Registry cleaners" (e.g., Registry Mechanic;
System Mechanic; RegCure; RegClean Pro; Advanced SystemCare; Registry Booster; McAfee QuickClean; Glary Utilities; AVG PC TuneUp; Norton Registry Cleaner; PCTools Optimiser; SpeedUpMyPC; PC Doctor; TuneUp Utilities; WinMaximizer; WinSweeper; Comodo System
Cleaner; Advanced System Optimizer; CCleaner's Registry Cleanercomponent)?
Not used any cleaners

Web page not displaying properly - content in wrong place

It's been years since I've done html and this is the first time using Dreamweaver. All my pages have the same header then a horizontal row of link buttons. I have used Divs to create 3 sections of content underneath this. Each div has the following defined for it: #Div { position:absolute; width:913px; height:440px; z-index:1; left: 10px; top: 302px; My main page is not displaying properly. There is a section on the left with text/photo. To the right of this section, there is a second div containing an image map. In Dreamweaver, I preview the page (using Chrome) and it looks fine. However, when I upload it to the web site and then view that page in the web site, the second div is thrown to the upper top right of the page. I do not know what is causing this and how to fix it. Can anyone answer this and perhaps give me some tips?

Start by fixing your HTML errors. You have a significant number of them.
http://validator.w3.org/check?verbose=1&uri=http%3A%2F%2Fgivethegaveltotavel.com%2F
Also, you have some CSS errors.
W3C CSS Validator results for http://givethegaveltotavel.com/ (CSS level 2.1)
Position:absolute is never a good way to layout your web pages. For 98% of what you do, positioning is not required and should be avoided. Learn to use CSS margins, padding and floats to align elements where desired.
CSS margin property.
CSS padding property
CSS Float
Nancy O.

Actiontec MI424-WR web interface not responding properly

Similar Messages

Maybe you are looking for