Active standby how to change?? + 32gb N96?

Hello, i have opted for the navigation bar that goes down the left hand side fo the screen for the standby apps, rather than basic or horizontal..... how do i change the ones it gives me
currently it has what looks like a diamond which is fine, but then it has calender, music, personalisation.... is there a way to change these??
Plus is there a 32gb n96 planned does anyone know... i heard there was.... I'll be cheesed off if there is, but delighted at the same time! :-)

Ok to change the applications in quick launch (i.e. the diamond):
RTM
Settings-> General -> Personalization -> Standby Mode -> Shortcuts
I don't know how to change the others.
About 32 GB N96 not sure what you mean.
You can buy a 16 GB memory card already today and that will bring your total memory to 32 GB.
640K Should be enough for everybody
El_Loco Nokia Video Blog

Similar Messages

Active/Standby Failover Config change

Hi everyone,
This weekend we are doing some change on ASA in Active/Standby mode.
We will power off standby ASA.
Do some changes on Active ASA save the changes and reboot it.
Power up the Active ASA and will test the connectivity if it is working or not .
In case Active ASA is not working as expected after the change i will power it off.
Power up Standby ASA then it will become active as expected.
Now if i Power up other ASA where changes were made will it synchnorize to old config from Standby ASA or not?
Last week we did some changes on Active ASA and it did not work as expected so we have to undo our change.
Need to make sure our backup plan is working?
Regards
Mahesh

In your fall back scenario you would have to tell what was the secondary ASA that it is now the primary
change
failover lan unit secondary
to
failover lan unit primary
and vice-versa on the now primary ASA.
change
failover lan unit primary
to
failover lan unit secondary
Hope it helps

FWSM Active/Standby in VSS mode

hello,
i do have two 6500 in VSS mode , and one FWSM module on each 6500, i want to configure these modules as Active/Standby, how do i start , should i follow this (not in VSS mode):
http://www.cisco.com/en/US/docs/security/fwsm/fwsm32/configuration/guide/fail_f.html
or are there other things should i do to make it work,
thanks

up!

How To Change of Credit Card Information When Purchasing an App?

Hello, when I firest registered for my Blackberry ID, I have logged my credit card information. Unfortunately, due to security issues, I have requested to cancel that credit card and change to a new account number. However, when I try to purchase another app and edit my credit card details, I have encountered an error which does not allow me to save my new billing information?
Can you advise how to change this so I can proceed purchasing apps again?
Note: My credit card is verified as active.

KB26621 How to change the payment method in BlackBerry App World for either the BlackBerry PlayBook or BlackBerry smartphone
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Help: how to change shortcuts in active standby mo...

i want to replace some of the shortcuts by others at active standby mode on N82.
does anybody know the solution since i can not find the API to do that.
thanks,

12-Jun-2008 11:42 AM
psychomania wrote:
Pass, it reads to me like they want to change the active standby shortcuts and can't find which application to use in the phone.
It reads like that to me too.
Grayburn @ www.nokiausers.net & www.dailymobile.se....come say Hello!!!
If you appreciate ANY help from a member,then show it by clicking on the Blue Star button, cheers

When creating a new window in safari, using command T, the marker have not activated the search field. It means you have to click there every time. Changed after upgrading to Mavericks. Anyone knows how to change this?

When creating a new window in safari, using command T, the marker have not activated the search field. It means you have to click there every time. Changed after upgrading to Mavericks. Anyone knows how to change this?

Yes, you can do something like that. What you would do is create a button for each image and then hide them. When I do this type of thing I place all of the buttons on a template page and then hide the template.
You can then use JavaScript to copy the icon from any of the hidden buttons to the main button that you've set up to display the image. For example, suppose you set up 10 buttons named b1, b2, b3, ...b10. The code to copy the icon from one of them to the button used to display the image (b0) would be something like this:
// Get the icon from the b3 button
var oIcon = getField("b3").buttonGetIcon();
// Get reference to the b0 button
var f = getField("b0");
// Set the icon of the b0 button to the icon retrieved from the hidden button
f.buttonSetIcon(oIcon);
// Show the b0 button
f.display = display.visible;
This code would go in the Mouse Up event of the smaller button.

How to change validity period of cost centre or activity type

Hi
How to change validity period for an Activity type or Cost centre?
Can we change the validity period once created?
regards
Prakash

Please note this can be done.
Go to Edit Cost Center
Goto Edit, Analysis Period.
Create a new validity period say today until 3112999
Change the data you want and save.
When you go into the CC again it will show two validity periods.

How to change a TAB dynamically to be the active tab?

Hi,
I have a portlet written in Java and registered using a web provider. This portlet exposes a link which drives the content of another portlet through parameters&events.
This other portlet is placed on the same page but on a different TAB (!).
What I want is, when clicked on the link in Portlet1, this changes the content of the Portlet2 (via an event and parameter - that works) AND should change the TAB, so that the TAB which contains the Portlet2 is active and shown.
I couldn't figure out, how to change the TAB with an event or any other way. I can easily change the page through an event, but not to a tab on the same page. Do I overlook something or can I just don't use events for this?
Is there any API function which does changing tabs or getting the tab id or is there any other programmatic workaround to do dynamic tab changing?
If so, can someone point me to a code fragment?
Any help would be much appreciated.
Cheers,
Erik

A work around may be to change the location.href to the url of the tab you want to switch to.
Have you tried that already?

N81 How to Show calender at active standby

Hi, i just bought a N81, but i just cant seem to get the phone to show the calender details for the day at the active standby mode(the main page). I can do it previously on my 6280.
Anyone can help?

12-Jun-2008 11:42 AM
psychomania wrote:
Pass, it reads to me like they want to change the active standby shortcuts and can't find which application to use in the phone.
It reads like that to me too.
Grayburn @ www.nokiausers.net & www.dailymobile.se....come say Hello!!!
If you appreciate ANY help from a member,then show it by clicking on the Blue Star button, cheers

CAMERA ON STANDBY & DO NOT KNOW HOW TO CHANGE IT

CAMERA ON STANDBY & DO NOT KNOW HOW TO CHANGE IT?
Since the phone has come back from repair I can not use the camera feature, I have no idea how to remove "Camera on standby"
Regards
John

They always perform a software update after a repair, but it sounds like in your case something went wrong here.
You don't say what kind of phone you have. If it is an S60 "Symbian" model, you can reformat it with the code *#7370#; if the phone is compatible with NSU (www.nokia.com/softwareupdate) you could reinstall the latest software yourself using your PC.
Failing both of those, you would have to go back to the repairer and tell them a new problem has been caused by the work they did.
Message Edited by mccbleue on 23-Feb-2009 07:57 PM

How to tell if Active/active or Active/Standby mode is configured?

Folks:
I am still learning the output of my running config, but how do I tell if my firewall is set to Actve/Active or Active/Standby mode?
In addition, how do I tell if it uses regular or stateful failover mode?
Thank you

I wanted to provide this as well, since I found it and it also helped me answering my question.
This output shows Active/Active failover output.
**Note** it says PIX; however, I beleive it will be the same output for ASA.
PIX1(config-subif)#show failover
Failover On
Cable status: N/A - LAN-based failover enabled
Failover unit Primary
Failover LAN Interface: LANFailover Ethernet3 (up)
Unit Poll frequency 15 seconds, holdtime 45 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 4 of 250 maximum
Version: Ours 7.2(2), Mate 7.2(2)
Group 1 last failover at: 06:12:45 UTC Apr 16 2007
Group 2 last failover at: 06:12:43 UTC Apr 16 2007
This host:    Primary
Group 1       State:          Active
                Active time:    359610 (sec)
Group 2       State:          Standby Ready
                Active time:    3165 (sec)
                  context1 Interface inside (192.168.1.1): Normal
                  context1 Interface outside (172.16.1.1): Normal
                  context2 Interface inside (192.168.2.2): Normal
                  context2 Interface outside (172.16.2.2): Normal
Other host:   Secondary
Group 1       State:          Standby Ready
                Active time:    0 (sec)
Group 2       State:          Active
                Active time:    3900 (sec)
                  context1 Interface inside (192.168.1.2): Normal
                  context1 Interface outside (172.16.1.2): Normal
                  context2 Interface inside (192.168.2.1): Normal
                  context2 Interface outside (172.16.2.1): Normal

How can changes happened during the cube activation be nullified.

Hi all,
I was trying to activate some business content infocube in the dev.server. I selectecd data flow before. In the process I collected all infoobjects associated with the cube and all the info-objects which are associated with that info-objects. When I installed the cube some of the customised business content info-objects associated with the cube got over written by the delivered version. We dont have the documentation which provides the information on which are all the infoobjects that were modified and which were not.
Can any one give some idea how the changes happened during the cube activation can be nullified.Or how can I find out which were the info objects which were customised before business content was again activated and which are those changes.
Regards,
Anand

Hi Anand,
As long as you did not activate the Cube (= not activate BC, but cube itself)
you can compare the changed cube with the active cube (Change cube screen, use button Version Comparison)
Udo

E51: How set active standby inbox to Gmail/All Mai...

I have a few problems setting up the active standby inbox to point to my gmail account's "All mail" folder.
First of all, it's not possible to unsubscribe to the Gmail inbox under Folder Subscriptions. This is a minor problem though as I don't use the Gmail inbox, but route all my emails to All Mail through a forwarding system.
So I'd like my active standby inbox to reflect the All Mail folder.
Selecting "gmail" under Email Settings/Default mailbox allows me to choose between "Inbox" and "[Google Mail]".
But, unlike in Email Settings/gmail/Retrieval Settings/Folder Subscriptions, I cannot go one step further and choose "All Mail".
This means that while my active standby inbox will show "gmail [Google Mail]" it won't show the new message(s).
Anyway around this? Well, apart from filtering all my emails to my inbox.

hello Graham
I guess you have disabled the active standby in-box plugin. Check it under "menu>tools>settings>phone>standby mode>active standby plug-ins", maybe you disabled it. Then under the same menu (standby mode) should be a new entry "active standby mailbox" where you have to select "inbox" for it to display those 2 latest sms in the active standby screen.
(the menu options may not be exactly as I mentioned, as I'm using portuguese UI)
Hope it helps
CheersMessage Edited by skanker on 08-Dec-200701:49 AM

E71-1 - No inbox/notification in active standby

In the past days I have tried to configure any kind of information about my primary email account for the active standby/home screen. The email account works fine (imap-idle account), receiving emails works fine, but other than the @-symbol in the top-right corner (when new emails are available) no information about the inbox or any indication about new emails are displayed on the home screen.
In the mode-config I selected the email account to be displayed on the home screen, and no matter what option I choose in the email notification 1 details (headers only, headers with popup, headers with unread etc.) nothing at all is shown. I have seen screen shots where at least a bubble notification is shown (for new emails) and also at least a link with the account name. The way it is now I have a really hard time keeping track of my (new) emails, because I really have to open my inbox every time to be sure.
I have tried every imaginable configuration detail, the manual is no help at all, and I didn't find any information in any forums about this problem. Is this a software bug? Has anybody experienced this? Is there a solution?

I've been experiencing the same issue where that active standby plugin wouldnt show a notification. But I *THINK* I have it figured out from the clues in this discussion. This post is to benefit any other people googling for the solution. To my knowledge, this method will enable you to have the single line email notication on your Active Standby aka homescreen (where your calendar and meetings show up) in the format of Gmail (6). I believe the catch is you need to have less than 999 emails in your inbox. As a workaround you need to archive all extra emails in your Gmail inbox. A disclaimer: I am not 100% on this, so I will give you as much detail to replicate my scenario where it works, so adjust it for your own situation
I went through various deletes of my Gmail account in the Email settings area of the NATIVE messaging app (where text messages are).
If you look at Messaging --> Options --> Settings --> Other
There is a setting called "Number of saved msgs." I figured out the maximum of this to be 999. In my opinion this setting is talked about saved SENT messages (the setting above it is called "Save sent messages" Yes/No). Set this number to 999.
I assumed this 999 number of messages to be the limit for all emails out of a hunch. I went into my Gmail account on the web and pretty much archived a lot of emails except the recent ones. Archiving your emails does not delete them, but rather stores them outside of the inbox and are still searchable within Gmail. I made sure the number of emails in my inbox were under 900.
Next, I followed the steps we all know to put in a Gmail account via IMAP via the setup email wizard and some minor tweaking in the settings dialogs (Messaging --> Options --> Settings --> Email --> Gmail --> Connections Settings --> Both Incoming e-mail and Outgoing e-mail sections) using the guide: Symbian S60 - Gmail Help
It might also be worth it to set your "Access point in use" for both incoming and outgoing servers.
Under
Messaging --> Options --> Settings --> Email --> Gmail --> User Settings --> New e-mail alerts should be ON
Under
Messaging --> Options --> Settings --> Email --> Gmail --> Retrieval Settings --> there are no necessary changes (the next section will override settings related to retrieval amount and cause ALL emails to be retrieved.). Note that putting folder subscriptions may put you over the 999 limit. I don't know if the 999 limit applies to each folder or to ALL emails as a whole. If you do put folder subscriptions, the next section setting will automatically also override the # of emails from folders retrieved to be ALL as well. Experiment at your own risk.
Under
Messaging --> Options --> Settings --> Email --> Gmail --> Automatic Retrieval:
Email notifications -- Disabled (you can only have one or the other and email retrieval is more important than this unknown and ill defined setting)
Email retrieval -- Enabled or "only in home network" (more options will appear now regarding scheduling. Pick your frequency according to how long you want your battery to last and how important your emails are). If you choose "only in home network" I am inclined to believe that it will only use the access point you described earlier in "Connection Settings"
Out of this menu,
Under
Messaging --> Options --> Settings --> Email
Make sure your default mailbox is Gmail
If you go into Modes (Modes--> Home screen apps --> Enabled apps) at this point and try to put the "Email 1 notification" as active, and go into "Email 1 notification's " settings, and try to set your mailbox to Gmail, it will tell you to connect first. So lets do that and hope it works
So go to Messaging --> Gmail --> Options --> Connect and watch it retrieve headers of your emails from Gmail. Make sure that theres 1 or 2 *NEW* emails before downloading for testing out the Active Standby plugin's temperment.
Go into Modes while it is retrieving the headers of your emails
Modes --> Home screen apps --> Enabled Apps --> and select "Email 1 notification"
Go back into
Modes --> Home screen apps --> Go into the new "Email 1 Notification" setting there
Mailbox: Gmail
Preview: You have a choice of three
Header only -- shows your mailbox's name and # of unread mails on homescreen -- eg: Gmail (3)
Header and popup -- show the header described above in 1 line, plus when you hover over it, a preview of your emails in a bubble that includes Sender, Subject, and Date. To me, this is the most useful
Header and unread -- Shows the header described above in 1 line, and in a 2nd line shows the most recent unread email's Sender, subject, and date
Assuming you've put a audio tone for email alerts in Profiles --> Whichever profile --> Customize --> Email alert tone
Then once you head back to your home screen and once the email retrieval finishes, you should hear a audio sound, and see Gmail (3).
Good luck

Active standby

how do i change the shortcuts underneath the six active standby apps whilst in standby mode
Solved!
Go to Solution.

You most likely remember correctly because it was indeed possible on older S40 phones. No longer on Nseries phones, which are based on Symbian S60.
Was this post helpful? If so, please click on the white "Kudos!" star below. Thank you!

Active standby how to change?? + 32gb N96?

Similar Messages

Maybe you are looking for