ActiveSync issue for a single user

Hello,
   We are finishing a migration to Exchange 2010 from 2007. Everything is connecting fine so far for all users except one. This user is the owner of the company, and a long time ago, like more than 20 years, instead of creating a copy
of the Built-in administrator account, he renamed it for himself.
   Anyway, he is the only user that is unable to connect via ActiveSync. The event viewer on the Exchange server says "User '[email protected]' cannot synchronize their mobile phone with their mailbox because Exchange ActiveSync has been
disabled for this user.   But of course, in the EMC, it says that he is enabled, and I ran the command in the Management Shell to ensure it was enabled.
   I did some research and found that checking the Include Inheritable Objects is supposed to help with this, but I did that and it still didn't work. It also became unchecked again after a while.
    I'm not sure where to go next at this point. Every other mailbox on the server ActiveSyncs no problem. It's just this one.
Thanks.

Create a new AD account for him that isn't a member of any built-in admin level groups and disconnect the existing mailbox and reconnect it to the new AD Account.
Mail Enabling the admin account is just not going to work well in 2010/2013 or beyond and its not a good security practice to use it except for elevated tasks. Hopefully the owner appreciates that.
You could mess with the AdminSDHolder stuff and allow the ActiveSync partnership to be created but I highly recommend against that.
http://eightwone.com/2011/08/31/exchange-activesync-and-inheritable-permissions-issue/
Twitter!:
Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

Similar Messages

Multiple AD account in single domain for a single user

Hi,
Does OIM support multiple AD account in single domain for a single user?
Scenario 1 :- If the multiple accounts already exists in AD can I pull it from AD to OIM for single user.
Scenraio 2:- Does OIM allow creation of multiple account in AD for a single user, when requested from OIM?
Thanks,

yes. this is possible. OIM allow this.
obviously the recon rule would be employee number or anything other than ' sAmAccontName' for target recon
while provisioning make sure you are generating unique sAmAccountName and Common Name(if in same OU) for same user
If you maintain above no issue having multiple account for a sing user in single domain

How to block a single table for a single user

Hi all.
I want to block a single Z table for a single user. How to do this? If he/she tries to display data using SE16 or SE11 Tcode he/she should get an error message.
Regards,
Prajwal K.

Hi Prajwal,
We can use the function modules ENQUEUE_E_TABLE for locking tables and the function module DEQUEUE_E_TABLE for unlocking tables. With this method, we don't need to lock objects in order to lock the tables. In other words, any table can be locked/unlocked using these function modules.
Check this sample code:
*Locking Table*
data:
varkey like rstable-varkey.
varkey = sy-mandt.
locking the tables............................
call function 'ENQUEUE_E_TABLE'
exporting
MODE_RSTABLE = 'E'
tabname = 'MARA'
varkey = varkey
X_TABNAME = ' '
X_VARKEY = ' '
_SCOPE = '2'
_WAIT = ' '
_COLLECT = 'X'
exceptions
foreign_lock = 1
system_failure = 2
others = 3.
Hope this helps you.
Regards,
Chandra Sekhar

LightDM greeter for a single-user system

I'm interested in using lightDM as my display manager. However, there seem to be a lot of greeters that are focused on a good experience for multi-user systems. All I'm have is a single-user system, so I'm looking for your guy's opinions on what the "best" lightDM greeter is for a single-user system. I want it to:
* Be pretty, even if it must be a bit more heavyweight. I consider "pretty" to mean modern/flat
* Be customizeable, hopefully with at LEAST customizeable colors, and preferably background images
* Have either a very modern/flat icon set, if there are icons at all, or customizeable icons
* Not force me to select my account every time I login, it should automatically "select" my account so all I have to do is enter the password. I *might* budge on this one if the design is *really* good
I'm ok if it has support for multiple users (I'm pretty sure every greeter out there will have that), but I don't want it to reserve too much space on the screen for multiple users, and I want it to still be good with one user. For example, I don't want it to be like crowd greeter, where it's nearly useless without many user accounts

Why not just test a number of greeters and evaluate which one most suits your use case? That's the common approach with most things.
You could also try other DMs like LXDM for example, in order to see how they compare.

NAC Guest Server, How to change the password for a single user?

We have a NAC Guest Server which creates a complex password for all new users created.
We would like to have normal/simple password for a single user. How can I get this done on a NAC Guest Server.
Thanks in advance.

Hi,
You can setup 3 different flavours of passwords:
http://www.cisco.com/en/US/docs/security/nac/guestserver/configuration_guide/20/g_guestpol.html#wp1063249.
a. Username Policy 1 - Email address as username
Use the guest's email address as the username. If an overlapping account with the same email address exists, a random number is added to the end of the email address to make the username unique. Overlapping accounts are accounts that have the same email address and are valid for an overlapping period of time.
b. Username Policy 2 - Create username based on first and last names
Create a username based on combining the first name and last name of the guest. You can set a Minimum username length for this username from 1 to 20 characters (default is 10). User names shorter than the minimum length are padded up to the minimum specified length with a random number.
c. Username Policy 3 - Create random username
Create a username based upon a random mixture of Alphabetic, Numeric or Other characters. Type the characters to include to generate the random characters and the number to use from each set of characters.
Note: The total length of the username is determined by the total number of characters included.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it.

Purchase Orders form in Query Only mode for a single user

Hi All,
I want to make the Purchase Orders form as query only for a single user. I tried by giving 'Query_only=Yes' in the parameters section. I am getting 'FRM-04151: You cannot query records here' message more than 10 time. I know we get this message and this is applicable to all the users. But this message is comming more than 10 times.
Is there anyway that I can restrict the Query only mode to a single user and please suggest about the message also.
Thanks in Advance,
Naresh

Please post this question here: OA Framework
There are so many special conditions and restrictions for E-Biz Suite that this forum is not the right place to ask these questions. The Apps forum at this location is the right place.

500 internal server error for only single user

Hi Experts,
Pls help me that
I am getting the problem of 500 Internal server error for a single user .
Except that user remaining users are not getting this error, They are working fine
i.e it is ESS & MSS Package all other application working fine , this iview came from Webdynpro .
Regards
Krishna

Hi Arun,
where can i check with that whether in DEV/PROD system...?
I don't have access to PROD system and SU01 system too.
Can you please guide me with the steps to get it done.
Please check the below log which is getting displayed for the User, when he is logging in.
Error summary
While processing the current request, an exception occurred which could not be handled by the application or the framework.
If the information contained on this page doesnu2019t help you to find and correct the cause of the problem, please contact your system administrator. To facilitate analysis of the problem, keep a copy of this
Root Cause
The initial exception that caused the request to fail, was:
com.sap.tc.webdynpro.services.exceptions.WDRuntimeException: ComponentUsage(FPMConfigurationUsage): Active component must exist when getting interface controller
at com.sap.tc.webdynpro.progmodel.components.ComponentUsage.ensureActiveComponent(ComponentUsage.java:773)
at com.sap.tc.webdynpro.progmodel.components.ComponentUsage.getInterfaceControllerInternal(ComponentUSage.java:348)
at com.sap.tc.webdynpro.progmodel.components.ComponentUsage.getInterfaceController(ComponentUsage.java:335)
at com.sap.pcuigp.xssfpm.wd.wdp.InternalFPMComponent.wdGetFPMConfigurationUsageInterface(InternalFPMComponent.java.245)
at com.sap.pcuigp.xssfpm.wd.FPMComponent$FPM.changeToExceptionPerspective(FPMComponent.java:862)
u2026 59 more
Please provide me any help.
Thanks in advance.
Regards,
Ponneswari A.

Step by step to disable Folder Redirection for a single user - Windows 7 and SBS 2011 Essentials

OK...I got chewed (by someone I have a lot of respect for) for pounding on an old thread, so I'm starting a new one. I've got the Windows 7 Value Pack Plugin for SBS 2011 Essentials and Folder Redirection is working for everybody. What I'm looking for is
exactly how to go into Group Policy and disable the FD for a single user. I'm not looking for quick, incomplete answers. If you don't have time to give me the 'For Dummies' version, don't bother. Sorry, but I've done all the Googling I can stand for one day
and I'm over it! (and a little grumpy)
Thanks in advance!
Wayne S. CompTIA A+ CompTIA Network+ Microsoft MCP

... I've got the Windows 7 Value Pack Plugin for SBS 2011 Essentials and Folder Redirection is working for everybody. What I'm looking for is exactly how to go into Group Policy and disable the FD for a single user. I'm not looking for quick, incomplete
answers....
Hi Wayne,
Here's what I'd do.
1) create a Security Group in your AD environment. Call it 'Folder Redirection Members' or something like that. Put all the user accounts in your AD environment who you want to have their folders continue to be redirected to the server, do not include the
one user who you wish to exclude. in other words, you're going to use a specific security group to target the Folder Redirection policy (right now, it's Domain Users, which is everyone).
2) Edit the Group Policy that the W7PP created in your AD environment. It's likely called "W7PVP Folder Redirection". Start with verification under the Settings tab, expand Folder Redirection beneath User Configuration states that
Policy Removal Behaviouris set to Restore Contents. Then proceed using the Editor, to make adjustments under the Scope tab; verify membership in Security Filtering. Remove Domain Users,
add in Folder Redirection Members (or whatever you named your group in step 1).
3) on your workstation that your user you are applying the change to disable folder redirection, Log on to the domain account while connected to your network, elevate a command prompt, and perform a 'gpupdate /force' command and then reboot your computer.
Folder redirection configuration should be removed from the system and redirected contents should be restored back to your local path. Verify with inspection of the My Documents or other folders.
Hope this helps. Keep in mind, no warranty implied or expressed in this advice.
Try not to be so darn grumpy. :-/
Jason Miller B.Comm (Hons), MCSA:Win7, MCITP, Microsoft MVP

Adobe Photoshop Extended CS6 for Windows (Single User Educational License): Are you discontinuing this? If so, when?

Adobe Photoshop Extended CS6 for Windows (Single User Educational License): Are you planning to discontinue this product? If so, when?

Adobe offers students teachers the Creative Suite for $20 a month. If you only want Photoshop Adobe advises students and teachers to get the Photography Subscription for $10 a month you can install Photoshop CS6, Photoshop CC, Photoshop CC 2014 and Lightroom.

IWork Licensing -Is Retail License for a single user or multiple users

I have a a Retail Version of iWork '08. How do I determine if this is for a single user or multiple users?
Thank you

So the next question is can I "unregister" this from my iMac thus allowing me to either reistall it on another machine or perhaps sell it?
Yes, you can. Apple doesn't "track" serial numbers, but you are doing the right thing by removing iWork '08 & it's registration. The file that keeps the serial number is the com.apple.iWork08.plist found in HD > Library > Preferences. This is the Library on the first level of your HD, not your user Library.

OWA with blank screen for a single user

Hello. I need some help to troubleshoot a situation on OWA 2013.
This is my scenario: I have a Windows Server 2012 (Not R2) fully updated with Exchange Server 2013 SP1 running.
I have 4 mailbox databases and about 260 mailboxs distributed among them.
My users, can connect through Outloook or OWA internal and external of my network. But theres a single user, which when he logon his account through OWA that shows a blank page with no script error, no source code, nothing. Just blank.
I had done some things to try to fix this with no success.
Had done this http://sumoomicrosoft.blogspot.de/2012/11/exchange-2013-emc-blank-page.html
Had tried to move the mailbox to another database.
Read entry by entry on event viewer to see if i find some error or information about this and no success so far.
Had removed and recreated OWA virtual directory and nothing happened. Still the same damn blank page.
On iis log, theres no usefull information about this access and i have no idea what else i could do to see if i can fix this.
What else you guys suggest for me to check?
Best reggards,
Kelson

Shelly, yes... It happens in all browsers and all computers just with that user. Funny thing is that's kinda random. If i reset iis, the user which had this problem, will not have it anymore but a new one will start to show this problem...
Then researching my event view, i found this event:
Event code: 3001
Event message: The request has been aborted.
Event time: 19/03/2014 03:41:22
Event time (UTC): 19/03/2014 06:41:22
Event ID: f619811eed154f1ca81bb74e60694b20
Event sequence: 2
Event occurrence: 1
Event detail code: 0
Application information:
Application domain: /LM/W3SVC/2/ROOT/Rpc-2-130396429825636242
Trust level: Full
Application Virtual Path: /Rpc
Application Path: C:\Windows\System32\RpcProxy\
Machine name: MyServer
Process information:
Process ID: 17584
Process name: w3wp.exe
Account name: NT AUTHORITY\SYSTEM
Exception information:
Exception type: HttpException
Exception message: Request timed out.
Request information:
Request URL: https://myserver.contoso.com:444/rpc/rpcproxy.dll?localhost:6001
Request path: /rpc/rpcproxy.dll
User host address: 0.0.0.0
User: NT AUTHORITY\SYSTEM
Is authenticated: True
Authentication Type: Negotiate
Thread account name: NT AUTHORITY\SYSTEM
Thread information:
Thread ID: 64
Thread account name: NT AUTHORITY\SYSTEM
Is impersonating: False
Stack trace:
and tried this: http://social.technet.microsoft.com/Forums/en-US/52f3f6b7-0114-4056-85d7-e46c615b7fa9/2013-cas-server-rpc-aspnet-event-1309-code-3005-unhandled-exception
Still testing if this issue still happens, but at the moment, seems to resolved it...

Entering mulitple values for a single user parameter

Hello,
Can anyone explain to me how to allow multiple values for a single parameter?
For example, say I want to allow the report to display a list of employees based on their employee id. I want to allow the user to enter mulitple
employee id's into a single field to get their report. SO the user would enter "241, 459, 832" to return the list of those 3 employees. I have the SQL set up below, but obviously I need to set up something different to break it out into 3 separate values. Any help would be greatly appreciated!
SELECT * FROM EMPLOYEE
WHERE EMPLOYEE_ID IN (:P_EMP_ID)

Hi,
Another way to do this is to use the lexical parameter, but then you have to create the parameter form in Forms. Your SQL would look like this for example:
select * from emp where empno is not null &empno
where &empno is a lexical parameter.
Then on your parameter form you would have a text field F_empid, say 200 character long, allowing the user to enter multiple values separated by a ",".
Then in the trigger that calls the report you would create a parameter list, and a variable that holds the values read from the form, this variable is where you define the value to be passed to the report's lexical parameter. For example:
declare
v_empid varchar2(200); (consistent with the length of the lexical parameter in the report).
begin
v_empid:='and empno in ('||F_empid||')';
then you pass v_empid to &empno in the call to the report.
This method works well. Good luck.

Multiple property value rows for a single user property

I use user properties to collect information about utilization of functionality.
My code sets properties in this way:
StringTokenizer st = new StringTokenizer (countersList, ",");
java.security.Principal pr = req.getUserPrincipal();
String userName = pr != null ? pr.getName() : null;
try
ProfileWrapper profilewrapper = ProfileFactory.getProfile(userName,null);
while (st.hasMoreElements())
String counterId=st.nextToken();
Long n = (Long) profilewrapper.getProperty("CounterUserProfile",counterId);
if (n != null)
n = new Long (n.longValue() + 1);
else
n = new Long (1);
profilewrapper.setProperty("CounterUserProfile",counterId,n);
catch (Exception e)
e.printStackTrace();
After some thousands access, looking in PROPERTY_VALUE table I found duplicated row
for same counter (user specific).
PROPERTY_KEY_ID ENTITY_ID MODIFIED_ LONG_VALUE PROPERTY_VALUE_ID
PROPERTY_SET_NAME
4008 28002 03-MAY-02 23 55678
CounterUserProfile
4008 28002 03-MAY-02 1 55680
CounterUserProfile
10002 22001 28-MAR-02 1 40017
CounterUserProfile
10002 22001 28-MAR-02 1 40018
CounterUserProfile
12001 22118 01-MAY-02 2 55448
CounterUserProfile
12001 22118 01-MAY-02 1 55449
CounterUserProfile
I use a single server instance with no clustering.
Any solution?
Thanks, Stefano

Stefano,
Please open a case with support, this looks like a bug in our code. They
will collect your configuration information which should help isolate the
problem.
Thanks,
Daniel Selman
"Stefano Crespi" <[email protected]> wrote in message
news:3cea49d4$[email protected]..
>
I use user properties to collect information about utilization offunctionality.
My code sets properties in this way:
StringTokenizer st = new StringTokenizer (countersList, ",");
java.security.Principal pr = req.getUserPrincipal();
String userName = pr != null ? pr.getName() : null;
try
ProfileWrapper profilewrapper =ProfileFactory.getProfile(userName,null);
>
while (st.hasMoreElements())
String counterId=st.nextToken();
Long n = (Long)profilewrapper.getProperty("CounterUserProfile",counterId);
if (n != null)
n = new Long (n.longValue() + 1);
else
n = new Long (1);
profilewrapper.setProperty("CounterUserProfile",counterId,n);
catch (Exception e)
e.printStackTrace();
After some thousands access, looking in PROPERTY_VALUE table I foundduplicated row
for same counter (user specific).
PROPERTY_KEY_ID ENTITY_ID MODIFIED_ LONG_VALUE PROPERTY_VALUE_ID
PROPERTY_SET_NAME
4008 28002 03-MAY-02 23 55678
CounterUserProfile
4008 28002 03-MAY-02 1 55680
CounterUserProfile
10002 22001 28-MAR-02 1 40017
CounterUserProfile
10002 22001 28-MAR-02 1 40018
CounterUserProfile
12001 22118 01-MAY-02 2 55448
CounterUserProfile
12001 22118 01-MAY-02 1 55449
CounterUserProfile
I use a single server instance with no clustering.
Any solution?
Thanks, Stefano

Change evtloglvl for a single user using srvmgr?

We want to analyze some problems in our environment with one specific user.
We use Oracle Siebel 8.2.2.3.
We know commands for changing evtloglvl for components, but not for users.
Is there any possibility to change the evtloglvl based on a user that log's in?
We didn't find anything in the bookshelf.

Also, depending on what you want to know maybe this document will be useful
How to enable object manager logging for only one user? (Doc ID 751270.1)
Thanks,
Florin

Password requirements for a single user

does anyone know of a way to change the password expiry requirements for an individual user?

See:
Page 291 "Managing Password Policies" of
OracleÂ® Internet Directory
Administratorâs Guide,
10g Release 2 (10.1.2)
Part No. B14082-01
December 2004

ActiveSync issue for a single user

Similar Messages

Maybe you are looking for