Add a simple wireless config to a Cisco 877 wireless?

Hi, I have a working Cisco 877w on an ADSL line. I'm trying to find out how I can add a simple wireless network to it? I can't find any instructions or examples on how to do this either in CLI mode or SDM.
Hope you can help

Here is a useful document which explains in detail how to setup a wireless connection using the 870 series wireless router.
http://www.cisco.com/en/US/docs/routers/access/800/850/software/configuration/guide/wireless.html

Similar Messages

Problem getting Airprint (Bonjour) to communicate to HP LaserJet CP1525nw printer across a Cisco 5508 Wireless Controller

I cannot get my IPad2 to print (it cannot find the printer) using a Laserjet CP1525nw color printer across a wireless network using a Cisco 1508 Wireless Controller with 49 wireless access points. HELP!!!!
What is the secret to getting Bonjour to work on it?
I can get the IPad2 to locate the HP CP1525nw printer without a hitch using a low budget Netgear WAG102 stand alone wireless access point on the same network.

If it helps somebody, here is what you need to do.
It worked for me, but only in Multicast-Unicast mode.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0 080bb1d7c.shtml

Unable to configure PPPoE in Cisco 877 for DSL connectivity

Hi,
I am trying to setup a DSL connection with Cisco 877 as the CPE. The CLI does not list the option of PPPoE for protocol in the vpdn group config prompt. If i manually enter PPPoE as the encapsulation, the vpdn group configured vanishes from the config!
Any clues? Has anyone got a sample config for a cisco 877 connecting to DSL through PPPoE. I followed the sample config in the TAC website giving the example for cisco 827-pppoe -DSL.
Some more inputs - as soon as i connect the DSL line the ATM interface line protocol comes up but unable to see anything in debug vpdn or debug ppp auth. The router IOS feature set is Advanced Security services.
Regards
NSG

Hi Gnanavel,
You need bba-group instead :
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/ftpprfls.htm#wp1088274
http://www.cisco.com/en/US/partner/products/sw/iosswrel/ps1839/products_feature_guide09186a00801541b8.html#wp1027195
Thanks and Regards,
~Zulfiqar

Can't add my new license on my cisco 2500 wireless controller

hello,
i already have 25 license installed on my Cisco 2500 wireless controller.
but when i need add my new bundle license, i can't see him on my admin panel.
i following this steps for installing my new license :
1- i go on WLC panel
2- management => software activation => commands
3- i select "install license"
4- i setting a correct path
5- when i clic on "install license", i can see two following message : "File transfer operation started" and "Installation Process Completed ". but when i go on "licenses" i can't see
tanks for help

Hi Serge,
In case you have another license installed on the controller with higher license than the one that you are installing, then the license installation will fail.
In case you want to install a new license with higher number of AP count, then you can install it, then save and reboot the controller.
Also I noticed when you install a new license and the summation of the previously installed license and the newly installed license is exceeding the max allowed AP count on the controller, then the installation will fail.
In such scenario, deactivate the current license by making the evaluation license priority to high, then after that install the new license and then change the priority to medium and make the evaluation license to low in addition to the previous license.
Kind Regards
Mohammad Setan

Hi I am hoping to add my 2 TB time capsule to my existing wireless network using cisco dpq 3925 modem. I have two mbp one running Yosemite and the other os 10.7.5

I have a time capsule 2TB model 1409. I would like to connect it to my existing wireless network (using a cisco DPQ 3925 modem). I have two mac book pro one running Yosemite and the other OS 10.7.5. The best I can do is to connect the TC to the Modem via ethernet. Have one of my MBP connect to the time capsule using a ethernet cable and have the TB set to bridge mode. In this configuration, both mbp and the iPad can detect the TC but when I try to connect it to the wireless network, using the same network name and password, the light flashes amber and I cannot detect the time capsule again.

Correct..
The best I can do is to connect the TC to the Modem via ethernet.
The TC does not connect to non-apple routers by wireless.. well. It is possible but so poor a method that Apple seem to have eliminated it in the setup wizard.. I would take that as a good thing..
If you cannot use ethernet you have two choices..
Use another apple router that is plugged into the Cable modem.. eg a second hand Extreme Gen5 or the latest Express.. the Extreme is both cheaper and better.
Or you can use a set of EOP (homeplug) adapters.. but they cannot be guaranteed to work so you should buy from a place that allows returns.

Cisco 7925 Wireless Phone Wireless Auto Config

Hello all,
My rehabilitation hospital is located right next to a large hospital connected by a catwalk. We have had 3 incidents where our RTs have gone over to the hospital next door for patient MRIs and our Cisco 7925 wireless phones are being configured with that hospitals wireless profile. The RTs are saying that no one from that hospital are manually configuring the phones to be on their wireless network so they can be used while off our wireless network. We're thinking that the RTs are putting their phones down and picking up the other hospitals 7925s by accident before leaving. My question to you is...Does the Cisco 7925s have an auto configuration tool that will automatically pick up on a particular wireless network and automatically configure itself and register with a Call Manager? Thanks!
Regards,
Terence

Leo and George,
Exactly! It makes absolutely no sense. All our Cisco 7925 phones are manually configured for our voice VLAN for our wireless network infrastructure. It's the only profile I've configured for those phones. I spoke to the other hospitals IT personnel and was advised that they use a wavelink server that sends the configuration to their 7925s after they have been entered into the server. The only explanation I can come up with is that our RTs are sitting our phones down, doing whatever they need to do over at the hospital, then picking up the hospitals 7925 thinking they're picking up ours. Another thing to note is that when I reconfigured the phone to be put back on our wireless, the phone performed a firmware update and then registered to our Call Manager.

Using Cisco wireless IP phones in Cisco Call Manager 5.1

Hello,
Currently we are using Cisco CallManager ver.5.1.2.3000-2, Berbee InformaCast ver.6.1.1 and Cisco Unity 1.1 Build 10. We like to replace few Cisco IP Phone 7961G-GE with Cisco Unified Wireless IP Phone 7920 ver.3.0. Does CCM ver. 5.1.2 supports Wireless phones? If it does, how do I configure it? Also, do I have to purchase any new license or other hardware?
Any suggestion / recommendations greatly appreciate.
Alex

Yes, it does:
Cisco Unified IP Phone Series 7900
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/compat/ccmcompmatr.html#wp51474
Config on CUCM itself is no different from any other phones neither other requirements like DLUs.
Of course you should already have APs for connectivity.
HTH
java
if this helps, please rate

Apple Airport in Cisco Enterprise wireless

Our wireless enterprise consists of Cisco Aironet 1200 series AP running ios 12.2(13)JA4. We are using LEAP with MIC, key-hash, and broadcast key rotation turned on. Airport seems to be working fine, but apparently it's a bug in this code that is allowing Airport user to authenticate. Newer codes break this authentication for Airports. Cisco is saying we are SOL. Airport is not on the CCX list, so go and talk to Apple guys. No word from Apple yet.
So, we can't be the only shop in this situation.
Any one out there are/were in same water and found a solution or way around it.
I would really appreciate any feed back.
Best regards,

I think that we close the loophole in CKIP and CMIC. In the earlier version of IOS, we allow wireless clients which do not support CKIP or CMIC to associate. The newer software does not allow these wireless clients anymore. I see the following workaround:
1. disable CMIC and CKIP on all Cisco APs
2. ask Apple to support CMIC and CKIP
3. purchase Aironet 350 wireless clients (do not flame me on this option. I add this option for the seek of completness)

Local RADIUS in AP1242 with non-cisco WinXP wireless clients

I'd like to configure local RADIUS in AP1242 and connect non-cisco WinXP wireless clients (for example notebook with integrated radio) with it. I did configuration (config1.txt) like in instruction: http://cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c0912.shtml
But I can't connect non-cisco WinXP wireless client with AP1242 anyway. At once Cisco wireless client with Aironet Desktop Utility connects with it without any problem. I've done some other configuration (config2.txt), but with the same result. Second configuration is rather then first.
How can I connect non-cisco WinXP wireless clients with AP1242 with local RADIUS?

Hi Stephen,
Thanks for the quick reply. Below is the switchport config. I am able to ping the AP from the switch and connect to its web page from any workstations.
interface GigabitEthernet0/5
switchport trunk encapsulation dot1q
switchport trunk native vlan 151
switchport mode trunk
end

Too many errors after upgrading the firmware to 1.0.3.10 on Cisco RV180W wireless router

My company purchased one Cisco RV180W wireless router few days ago and it worked normal with default firmware version of 1.0.0.30. Today I upgraded the firmware to version 1.0.3.10, the users can still access this router via wired and wireless devices, but on the dashboard I observed two major problems, one is the CPU utilization always shows 100%, another is the more and more errors appearing, on the Syslog Summary panel "Error" log has been up to 625 and is still increasing, there is one message repeatedly displaying in the log, see in below:
Wed Nov 13 13:55:25 2013(GMT+0800) [rv180w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 100 failed. status=-1
Who can tell me what does this error message mean and how to elinate this error message ? also how to deal with 100% CPU utilization ?
Thanks.

Hello,
i have been looking at different VPN routers over the last few weeks and i was very close to buying the RV180W, but then i stumbled across many posts reffering to firmware issues, one issue is that the cpu sits at 100% useage, i just wondered if this is a bug in GUI or is the CPU actually max'd out? has anyone had any resolution into this?
also the firmware on the emulator is a newer version than is listed on the support page, does anyone know when 1.0.3.14 will be released for download?
when i buy a new product i like to ensure that the system is fully upto date before its put into use but i obviously dont want to add any performance issues from the ofset due to the CPU useage.
i also have a could of questions if anyone can help
the Ipsec VPN, will this work with the Built-in VPN client for apple devices? (New IOS7), i am unable to find a quickvpn application for apple IOS.
is the site-to-site IPSec VPN also compatible with the Cisco Wvrs4400n router?
thanks in advance.

Need cisco 3650 wireless configuration

Hi there,
we are using new Layer 3 3650 switches which has inbuilt wireless capabilities but i need configuration so can plug some AP's to it.
WS-C3650-48PS 03.03.03SE cat3k_caa-universalk9
could some one please share there basic config so i can test it ?
thanks so much in advance.

Hi,
Here is the config guide for Wireless controller config
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3650/software/release/3se/mobility/configuration_guide/b_mobility_3se_3650_cg/b_mobility_3se_3650_cg_chapter_01001.html
HTH

Configure VPN access on a Cisco WRV210 wireless-G vpn router -range booster

Please help....
I need to configure a vpn on a Cisco WRV210 Wireless-G VPN Router - RangeBooster, i have five users that are going to connect to a file server. windows and Mac laptops will be connecting. The file server access is all set i just need a step by step document to configure the vpn screens on the router.thanks

Hi Robert
You can refer the below link in finding out the exact config to start with.
do make sure that your Cisco 831 box with the current IOS code installed in it supports the required feature to run the same..
http://www.cisco.com/en/US/tech/tk583/tk372/tech_configuration_examples_list.html#anchor16
regds

I just set up an Optus Cisco DPQ3925 wireless router to access higher speed internet I signed up for. I have a 4th gen airport extreme I want to put in another room and use as a wifi extender the wifi but I get an error message each time I try. Help?

Hello all.
I have just set up a new cisco DPQ3925 wireless router that Optus sent me to be able to access the higher speed internet I have signed up for.
I have a 4th gen apple extreme that I want to use to extend the wifi but when I try to update the settings via the airport utility I get a message that says it cannot do so, and to check it is in range and the wifi is set up correctly. I'm not experienced with these things but I can't think what I have done wrong.
Is anybody able to help me please.

You cannot use the AE to extend wireless from a non apple router such as your cisco modem router.. they are not compatible..
You need to tie to the two devices together either with ethernet or something like EOP adapters.. They are about $120 and you can price match in officeworks.

Ask the Expert: Cisco BYOD Wireless Solution: ISE and WLC Integration

With Jacob Ideji, Richard Hamby and Raphael Ohaemenyi
Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the new Identity Solutions Engine (ISE) and Wireless LAN Controller (WLC) hardware/software, integration, features, specifications, client details, or just questions about Cisco's Bring-your-own device (BYOD) solution with cisco Experts Richard Hamby, Jacob Ideji, and Raphael Ohaemenyi. The interest in BYOD (Bring You Own Device) solutions in the enterprise has grown exponentially as guests and company users increasingly desire to use personal devices to access . Cisco BYOD enhances user experience and productivity while providing security, ease-of-administration, and performance. The heart of the Cisco wireless BYOD solution is Identity Solutions Engine (ISE) utilizing the Cisco Unified Wireless portfolio. Starting with ISE v1.1.1MR and WLC (Wireless LAN Controller) code v7.2.110.0 and higher, end-to-end wireless BYOD integration is reality.
Jacob Ideji is the technical team lead in the Cisco authentication, authorization and accounting (AAA) security team in Richardson, Texas. During his four years of experience at Cisco he has worked with Cisco VPN products, Cisco Network Admission Control (NAC) Appliance, Cisco Secure Access Control Server, and Dot1x technology as well as the current Cisco Identity Services Engine. He has a total of more than 12 years experience in the networking industry. Ideji holds CCNA, CCNP, CCSP, CCDA, CCDP, and CISM certifications from Cisco plus other industry certifications.
Richard Hamby works on the Cisco BYOD Plan, Design, Implement (PDI) Help Desk for Borderless Networks, where he is the subject matter expert on wireless, supporting partners in the deployment of Cisco Unified Wireless and Identity Services Engine solutions. Prior to his current position, Hamby was a customer support engineer with the Cisco Technical Assistance Center for 3 years on the authentication, authorization, accounting (AAA) and wireless technology teams.
Raphael Ohaemenyi Raphael Ohaemenyi is a customer support engineer with the authentication, authorization and accounting (AAA) team in the Technical Assistance Center in Richardson, Texas, where he supports Cisco customers in identity management technologies. His areas of expertise include Cisco Access Control Server, Cisco Network Admission Control (NAC) Appliance, Cisco Identity Services Engine, and IEEE 802.1X technologies. He has been at Cisco for more than 2 years and has worked in the networking industry for 8 years. He holds CCNP, CCDP, and CCSP certification.
Remember to use the rating system to let Jacob, Richard and Raphael know if you have received an adequate response.
Jacob, Richard and Raphael might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the wireless mobility sub community forum shortly after the event. This event lasts through Oct 5th, 2012. Visit this forum often to view responses to your questions and the questions of other community members.

OOPS !!
I will repost the whole messaqge with the correct external URL's:
In general, the Trustsec design and deployment guides address the specific support for the various features of the 'whole' Cisco TS (and other security) solution frameworks. And then a drill-down (usually the proper links are embedded) to the specifc feature, and then that feature on a given device. TS 2.1 defines the use of ISE or ACS5 as the policy server, and confiugration examples for the platforms will include and refer to them.
TrustSec Home Page
http://www.cisco.com/en/US/netsol/ns1051/index.html
http://www.cisco.com/en/US/solutions/collateral/ns170/ns896/ns1051/product_bulletin_c25-712066.html
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps5712/ps11637/ps11195/at_a_glance_c45-654884.pdf
I find this page very helpful as a top-level start to what features and capabilities exist per device:
http://www.cisco.com/en/US/solutions/ns170/ns896/ns1051/trustsec_matrix.html
The TS 2.1 Design Guides
http://www.cisco.com/en/US/solutions/ns340/ns414/ns742/ns744/landing_DesignZone_TrustSec.html
DesignZone has some updated docs as well
http://www.cisco.com/en/US/netsol/ns982/networking_solutions_program_home.html#~bng
As the SGT functionality (at this point) is really more of a router/LAN/client solution, the most detailed information will be in the IOS TS guides like :
http://www.cisco.com/en/US/docs/switches/datacenter/sw/6_x/nx-os/security/configuration/guide/b_Cisco_Nexus_7000_NX-OS_Security_Configuration_Guide__Release_6.x.html
http://www.cisco.com/en/US/docs/ios-xml/ios/sec_usr_cts/configuration/xe-3s/asr1000/sec-usr-cts-xe-3s-asr1000-book.html
http://www.cisco.com/en/US/docs/switches/lan/trustsec/configuration/guide/trustsec.html

How can I add a simple URL to Streamwork?

Hi,
I want to add a simple URL to a StreamWork activity. I do not care whether this is in a text or a collection etc. All I would like to see is that the URL is displayed as such (i.e. blue, underlined) and a user can navigate to the URL with a simple cklick. Even in WORD you can do this and the URL is converted to an active link automatically, but I didn't find a way to do this in Streamwork.
So far, I add the URL into a text and then the user has to edit the text, mark the URL and then copy/paste it into a browser. In a lot of cases, the URL was deleted by accident or changed etc.
Thanks
Oliver
Edited by: Oliver Nuernberg on Jan 28, 2011 10:03 AM

Maybe there is a misunderstanding here -- Rob is probably thinking of the Status Updates.
However, when you edit a Text item you will find a Hyperlink option in the tool bar at the top of the Item. So this is possible, Oliver, but you may not have seen this option.
Thanks,
Pete

Add a simple wireless config to a Cisco 877 wireless?

Similar Messages

Maybe you are looking for