Add Additional IP Addresses to WAN Interface on SRP527W

Hi,
Can anyone tell me how to add an additional IP addresses to the WAN interface on a SRP527W.
We are connecting to an ISP which assigns us a static IP address with our ADSL account. We also have another 2 additional WAN IP addresses that we have purchased from out ISP and wish to add them as Aliases to the WAN interface and use for other services. I would also like to use those additional IP addresses to create port forwards to our internal network.
I cannot find how to do this in the manual any where and any help would be much appreciated.
Regards
Craig

Hi Craig,
Unfortunately, this is not possible with the SRP520.
[For others reading this thread, this is possible with the SRP540]
Regards,
Andy

Similar Messages

Why can't I add additional email addresses to my Apple ID?

In my family we share the same Apple ID.
However, we would like to be able to use iMessage and Facetime amongst the different units (iPhones/iPads), which requires me to have several email addresses registered under the Apple ID, as all units (ie. the iPads) do not have associated phone numbers.
However, when I add them directly under Settings -> Facetime/iMessage -> Add Another Email it gives me an error (unspecified - it just says an error occured), when it tries to verify my email.
I then figured that I needed to have all these different email addresses registered to my Apple ID we all are using. Hence I went to appleid.apple.com and signed in to manage my Apple ID. I tried adding additional email addresses under "Add Email Address". But when I push "Save Changes" after having added another email address nothing happens. It just sits there.
I have tried several different browsers on different Macs and even on the iPad, but all with the same result.
Can anybody help?

Hey Thomas,
I was able to get my MobileMe email address verified tonight... I logged into the Manage Apple ID website with my MobileMe email address and it again said it's own email address wasn't Verified. So I tried, for the **** of it, to add an additional Alternate Email Address and added the MobileMe email address for which I was logged in as. It immediately took the email and marked it verified with the green check mark. The only thing, my MobileMe.com email address shows up as the Primary and then again listed under the Alternates. I tried deleting the one listed under the alternate but it doesn't go away. I'm just trilled it's now verified and I can log in and use my MobileMe email address in the iMessage, FaceTime and Find My Friends services!
I still cannot, however, delete my MobileMe email address that's still listed as an un-Verified alternate on my old iTunes Apple ID, but it's not affecting the fact that my MobileMe email address is NOW verified on my MobileMe Apple ID!
So all is finally working now, after a week, and after being on Apple's Express Lane Chat and to the store's Genius Bar on Thursday 10/20 which were both a joke.
Brian

IMessage shows error message when I try to add additional email addresses

I have an iPod touch and everything is working OK, email, safari, wifi etc. However when using iMessage i do not want to use the same email that i use for my iTunes account. So I have tried to add one of my additional gmail accounts. However when attempting to verifying the address, I get a message, An error occurred while verifying your emaile. Any one has a clue towhat is happening??
PS.I am located in indonesia at this time and my Aoole account is our of Australia.
Pak Frank

Hi,
We typically see this when an organizations IT department is blocking the upload of images. Are you working on this at work? If so, can you try adding the image outside your companies network?
Thanks,
Todd

Cannot add additional email address.

I am trying to add an additional email account to my iphone but the 'add account' option is grayed out. Help?

As far as adding alternate e-mail addresses to be associated with a single Apple ID, after going through the steps that you mentioned, you should get a verification e-mail each time you add an additional address.
As Apple states; "Verify your changes by following the link in the e-mail you will receive from Apple and signing into your account."
Simply stated, it sounds like you are not verifying the new addresses after you enter them. I am not sure if the verification e-mail goes to the new e-mail address you added, which is likely, or the original, so check both.

HT4436 How do I add additional email addresses to my account?

I want to add an additional email to my account for my little girl. How do I do that?

You can create an email alias at the mail feature at iCloud.com

DHCP disable on WAN interface

Hello,
I have a cisco router 1721, IOS 12.4(25a)
I enabled dhcp server for my local LAN, and I setup my WAN interface as dhcp interface.
My ISP told me that my router is acting as dhcp server on WAN interface...and is not good for them. Can I stop my cisco router from sending dhcp offers on WAN interface, but send dhcp offers for my local LAN ?
ip dhcp pool LOCAL
   import all
   network 192.168.1.0 255.255.255.0
   dns-server 193.x.x.x
   default-router 192.168.1.222
   domain-name appt.ro
   lease infinite
ip dhcp pool host1
   host 192.168.1.11 255.255.255.0
   client-identifier 0100.0ee8.e23d.94
interface FastEthernet0
mac-address 0019.66b3.d689
ip address dhcp
ip nat outside
ip virtual-reassembly
speed auto
full-duplex
FastEthernet0 is my WAN interface.
Thanks!

I imagine that clients on the WAN side are sending requests with a GIADDR field that matches your DHCP pool's scope. In that case, the router would handout an address. You could add an ACL to the WAN interface to block incoming udp/68 packets:
access-list 101 deny udp any any eq 68access-list 101 permit ip any any!interface FastEthernet0 ip access-group 101 in
That should prevent the router from seeing the client requests while still being able to get server responses.

CRM B2C Shop : How to add multiple delivery addresses ?

Hi
We have a requirement add multiple delivery addreses to the Web shop user. The default process adds an address when registering. This works. We need to add additional delivery addresses. I have tried the following code, but it doesn't work:
             User user = null;
          Address address = null;
          user = bom.createUser();
          user.clearMessages();
          BusinessPartnerManager buPaMa = bom.getBUPAManager();
          address = new AddressFormular(requestParser).getAddress();
          BusinessPartner partner = buPaMa.createBusinessPartner(user.getBusinessPartner(), null, address);
          SoldTo soldTo = new SoldTo();
          if(!buPaMa.addPartnerFunction(partner,soldTo))
               String error = buPaMa.getMessageList().toString();
Any suggestions?

Hi
Thanks for the info. I realise the code I added will not do what I want. My requirement is NOT to add a delivery(ship-to) address to the order, but to list, add, remove delivery addresses of the users profile from CRM. Our CRM consultant directed me in the right direction. The standard CRM bapi's to handle BP addreses are:
BAPI_BUPA_ADDRESSES_GET
BAPI_BUPA_ADDRESS_ADD
BAPI_BUPA_ADDRESS_CHANGE
BAPI_BUPA_ADDRESS_GETDETAIL
BAPI_BUPA_ADDRESS_REMOVE
I searched the CRM Shop standard Java code and these bapi's are not called. We will have to write custom Java to implement these bapi calls.
Thanks,
Chris

Adding additional Email Address (Email Alias) To DL

Hi,
I have 1000 DLs and each DL has around 5 existing email addresses. I want to add 6th one now to all 1000 DLs. Is there any way to add additional email address without overwriting existing ones? The command below is deleting existing email addresses
Set-DistributionGroup "ABC Group" -EmailAddresses SMTP:[email protected]
I want to add without deleting older ones.
Hasan

$DG=Get-DistributionGroup -resultsize unlimited
$DG.EmailAddresses +="[email protected]"
Get-DistributionGroup -resultsize unlimited | Set-DistributionGroup -EmailAddresses $DG.EmailAddresses
Important: Test first against only 1 or 2 groups before applying in bulk
Twitter!:
Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.
You rock man... Thanksssssssss... Its just i did some modifications. This + did the trick, thanks a lot.
$DG=Get-DistributionGroup -identity "1"
$DG.EmailAddresses +="[email protected]"
Set-DistributionGroup "1" -EmailAddresses $DG.EmailAddresses
Hasan

Adding additional email addresses to From field

In the default iOS Mail app, how can I add additional email addresses to the "From" field? It only allows me to select accounts which are set up on the phone. However I have one email account which forwards to another, but I want to respond to those messages using the original address it was sent to.

SOLVED.
Once a ePrint job had been submitted from each of the email addresses I added in the Allowed Senders Only list, all emails showed up on the ePrint Settings list. Works fine.

Why do I have to click each time in the "TO" bar to add an additional email address? Before 4.0, I could keep typing and adding more addresses.

When typing people to send my email to, I have ALWAYS been able to start typing and the address pops up, so I select it, then I can start another, and so on. NOW I can only start typing and select ONE email. The cursor is no where to be found and I can only add more email addresses by clicking EACH time in the address bar. HATE THIS!!!!

Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
* https://support.mozilla.com/kb/Safe+Mode
If it does work in Safe-mode then disable all extensions and then try to find which is causing it by enabling one at a time until the problem reappears.
* Use "Disable all add-ons" on the [[Safe mode]] start window to disable all extensions.
* Close and restart Firefox after each change via "File > Exit" (Mac: "Firefox > Quit"; Linux: "File > Quit")
In Firefox 4+ you can use one of these to start in <u>[[Safe mode]]</u>:
* Help > Restart with Add-ons Disabled
* Hold down the Shift key while double clicking the Firefox desktop shortcut (Windows)
* https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

Does the RV042 have IP Aliases for WAN interface?

Hi All
We have a Small Business RV042 router, and have many Internet servers in our Internal and DMZ networks behind the router.
In our old GTA firewall, we were able to add IP aliases to our external (WAN) interface.   That is, our WAN interface can have many IP addresses besides the main IP address, e.g., 209.118.52.226, 209.118.52.227, 209.118.52.228, 209.118.52.229, etc.
209.118.52.226 is the main IP for the WAN interface.
209.118.52.227 is for our web server 1, e.g., www.example.com
209.118.52.228 is for our web server 2, e.g. support.example.com
209.118.52.229 is for our sftp server, e.g. sftp.example.com
And then we create 'tunnels' to forward incoming traffic for 209.118.52.227 to our www.example.com residing in our DMZ or Internal network, etc.
Now, is this possible with the RV042 router?    The only thing we found in RV042 is Forwarding (port range forward) but that does allow us to have IP aliases for the WAN interface.   It seems that we can only route service defined traffic or port defined traffic meant for only 1 WAN IP to our internal servers behind the router.
Actually, we had bought the RVS4000 earlier and then upgraded to the RV042 hoping that it will have what we want.
If the RV042 does not have IP alias for WAN interface, what is the lowest Cisco router model that has it?
Thank you very much in anticipation.
cmgui

Thank you tekliu
Yes, 1-to-NAT can do most of what we want.   But it is not able to direct only certain port traffic from the external WAN IP to the internal LAN IP?
For example, if we create a 1-to-1 NAT 192.168.41.50 =>
209.118.52.227, it basically opens all the traffic allowed in the Firewall to go from
209.118.52.227 to 192.168.168.41.50.
If we only want to allow say https, ie. tcp port 443, traffic to go from
209.118.52.227 to 192.168.41.50, it is not possible. Or is it?

How do I add an email address for a family member to my .mac account?

Can I add an email address for my mother to my .mac account? I'd like to set up, manage and pay for an email address for her use. I thought this was possible but can't seem to navigate myself to the place where I can get an additional address.

So, after further reading I assume that I must ad an apple id for my mother. Is this correct? Can I, as the responsible party, control purchases and apps that are added to the device I have provided her? I'm not so worried about what she might do as I am what a grandchild might do without her knowledge.

How To Add Additional Fields When Creating New Contact From w/in Mac Mail?

Hi there. When in Mac Mail and clicking on contact information provided within an email, we are able to either (1) CREATE NEW CONTACT or (2) ADD TO EXISTING CONTACT (by clicking on the arrow next to a phone number, address, etc.). If I choose "Create New Contact," how can I add additional fields BEFORE clicking on "Add to Address Book" button in lower right corner? Let's say, for example, I know this new contacts URL or company. (Currently, I am creating the new contact from within Mac Mail and then going to Address Book and finding the contact, then editing, the adding the additional fields, then saving, and then going back to Mac Mail. This all takes time.)
Note: When creating a new iCal event from within Mac Mail, we can click on Option/Alt key when selecting drop-down arrow...and this will allow us to add additional information. The same feature isn't available for address book???

I have the exact same question and problem. If there was a way to automatically open the AB entry after "creating new contact" this would solve it.
Thanks for any suggestion

How do you add a MAC address to air port

How do you add a MAC address to anAir Port

Hi CarlMcc!
I have an article here that may help you with this question:
AirPort base stations: How to view WAN and Wi-Fi MAC addresses
http://support.apple.com/kb/HT5566
Thanks for being a part of the Apple Support Communities!
Regards,
Braden

Multiple DMVPN Instances on Same WAN Interface

Hi Folks,
Is it possible to run Multiple DMVPN Instances on a single WAN Interface ? Can we for example configure 3 Tunnels on a Router using one same WAN Interface but running separate EIGRP Instances for each Tunnel ? Kindly let me know , Alioune

Hi Alioune,
Yes you can create DMVPN as you said with one WAN interface that is possible..... you can have multiple tunnel interfaces pointed to a WAN interface as the source interface which resides in public zone..... with different public ip's as the destination tunnel...
interface Tunnel1
description ** A-VPN Tunnel **
bandwidth 100000
ip vrf forwarding red
ip address 10.0.252.2 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1500
load-interval 60
tunnel source GigabitEthernet0/0 (WAN Interface)
tunnel destination 1.1.1.1
tunnel protection ipsec profile dmvpn
interface Tunnel1
description ** B-VPN Tunnel **
bandwidth 100000
ip vrf forwarding red
ip address 10.0.252.5 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1500
load-interval 60
tunnel source GigabitEthernet0/0 (WAN Interface)
tunnel destination 2.1.1.1
tunnel protection ipsec profile dmvpn
like the above..... shown sample...
Please rate if the given information helps!!!

Add Additional IP Addresses to WAN Interface on SRP527W

Similar Messages

Maybe you are looking for