Add another 4gb ram for g6-2148tx

Is it a good idea to add another 4gb ram to my new g6-2148tx laptop? How much is the maximum ram for it? What type ram do I need? Do I need to match exactly the same as pre setup one?
Thanx

Hi,
The max number is 8GB (4GB + 4GB). Depending the current configuration:
(a) if 2GB + 2GB: you have to throw them out to get 2 + 4,
(b) if 4GB + 0GB: you need only one piece.
I can't find its full specs on HP (both Oz & Kiwi) therefore please use the following program to find out the right specs for RAM:
ftp://ftp.cpuid.com/cpu-z/cpu-z_1.61.3-g1-setup-en.exe
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

Need 4GB RAM for 2010 27 "computer where to buy it?

I need 2 4GB RAM for 2010 27 "computer where to buy it?

I installed exactly the combination you are considering in my 21.5 inch i-Mac a couple of weeks ago. I bought it from OWC based on comments and recommendations on this forum (and the fact that they are close to me as I was thinking of picking it up to save delivery time). As it turns out I had it sent, the RAM arrived the next day and I installed it in 10 minutes and it runs and performs perfectly.

HT1270 from where can i purchase 4gb RAM for my macbook pro 13'' mid 2012 model?????

from where can i purchase 4gb RAM for my macbook pro 13'' mid 2012 model?????

I would advise if you have to buy it get 8 or 16gb of ram. it will boost your preformance alot.
16 ($109)
http://www.amazon.com/Corsair-Channel-SODIMM-Memory-CMSO16GX3M2A1333C9/dp/B006DI 9PG8/ref=sr_1_18?s=electronics&ie=UTF8&qid=1378735908&sr=1-18&keywords=Corsair+1 6
8gb ($50)
http://www.amazon.com/Corsair-1333mhz-PC3-10666-204-pin-CMSO8GX3M2A1333C9/dp/B00 2YUF8ZG/ref=sr_1_1?s=electronics&ie=UTF8&qid=1378735731&sr=1-1&keywords=Corsair+ 8GB+%282x+4GB%29
4gb ($33)
http://www.amazon.com/Kingston-ValueRAM-1066MHz-Non-ECC-Notebook/dp/B001PYDKWU/r ef=sr_1_48?s=electronics&ie=UTF8&qid=1378735625&sr=1-48&keywords=corsair+4gb+ddr 3+corsair

Custom display template - how to add anothe display template for refimement item?

Custom display template - how to add anothe display template for refimement item?
I add a new filter_default_custom.html file and want to create new refinement item display template to point to it
keren tsur

Not 100% if I understood the question, but if you uploaded your template to the Master Gallery and the corresponding .js file has been created, you can open the refinement config panel and specify the result type you want to map to your custom template.
http://www.eliostruyf.com/part-1-create-first-search-refiner-control-template/
Kind Regards
Bjoern
http://www.sharepointviking.com
Twitter: Follow @bjoern_rapp

How to add another Chapter Page for more then 6 chapters & add right arrow?

Hello,
I created a project via the Magic iDVD option and it worked great and added multiple chapter pages for more then 6 chapters. Now, I manually added a submeno off of main and added 6 chapters but I need multiple pages since I have 40 chapters... I can't figure out how to add another chapter page and create a RIGHT ARROW navigation button for the next pages...
I also looked at the map view and see that on the working pages there is page connected to page... I also cannot find a way to add a page connected vi map view...
I have searched the forum but none of the answers were clear on how to do this... any help would be appreciated...
Thanks! T.

Adding the submenu is easy...making the button for it a "right arrow" is not.
You can keep adding submenus to other submemus by navigating to the appropriate menu and then choose the "add submenu" command from the iDVD project menu. This can be done in either normal or map view.
However, this creates a "folder" button, (or other things in some themes) not a right arrow. I agree it should be a choice! My 2nd best solution is to chage the folder button to a "text only button" and label it "More Chapters > >"
Another solution (3rd best??) is to use command-shift-4 when you are one one of your other menus that DOES have a right arrow, and take a mini picture of the arrow. Then choose one of the oval menu buttons on the button pane, and drag this tiny picture onto the button. Re-size it to make it close to the same size as your other buttons. It will have a funny edge on it from the button style, but it will look like a right arrow.
John B

What the price of 4gb ram for hp pavilion DV6000?

how much it cost to replace new 4gb ram in laptop. model no-hp pavaliion dv6000 and which company and what type?

The geek squad might have to advise you on this one however I thought it had support for PC2 - 5300 ram.
*******DISCLAIMER********
I am not an employee of BBY in any shape or form. All information presented in my replies or postings is my own opinion. It is up to you , the end user to determine the ultimate validity of any information presented on these forums.

4GB ram for P6N SLI Platinum

Can anyone recommend me good quality ram for my P6N SLI Plat. board ? I know some memory is incompatible with it so I need to know which one I can buy that will work and good memory.
I have Q6600 + 8800GTS 640 and P6N SLI Platinum bios v.1.1.

I've been extremely happy with running Corsair Dominator PC-8500C5D's (rated 1066 but 800 chipped), in both P7N & P6N. If your OS is XP, the 2X1G set in slots 1 & 3 works good. If you have Vista, 2X2G set in slots 1 & 3 would be a good combo as well.

How to add another operating system for Dual boot in Windows 7 boot configuration

Hi,
I have dell laptop with excellent configuration. On which i had windows 7 Home premium on C Drive and Windows server 2008 on D Drive.
Now i upgraded my Windows 7 Home Premium 32 bit to Windows 7 Ultimate 64 bit. But after fresh installation of Win 7 Ultimate my dual boot screen has gone and Win 7 is getting start directly.
Now i want to add my Windows server 2008 again for dual boot which is still on D Drive.
Can anyone please tell me how to add windows 2008 boot option in boot configuration to active my dual boot options.
Thanks

1) Using bcdedit.exe /enum
To enable the computer to also boot Windows 7 you again use bcdedit.exe with the following command which will copy the current Windows
Boot Loader details for Windows Server 2008 to Windows 7.
bcdedit.exe /copy
{current} /d "Microsoft Windows 7"
bcdedit.exe will
respond with something like the following.
The
entry was successfully copied to {................................}.
Using
bcdedit.exe /enum to again enumerate through the current entries within the BCD store you'll see the newly added entry.
Before you can use the newly created Windows boot loader configuration, you'll need to change the partition for Windows 7 using
the following two bcdedit.exe commands.
bcdedit.exe /set {.................................} device partition=D:
bcdedit.exe /set {.................................} osdevice partition=D:
If you now reboot the system you should now be able to boot into either Windows Server 2008 or Windows 7.

How do I add another operating system for Dual boot in Windows 8.1 boot configuration?

Hello,
I am trying to create a dual-boot Windows 8.1 Pro system to allow both 32bit and 64 bit Windows 8.1 versions. I currently have Windows 8.1 32bit installed. Appreciate some background on how to add 64bit Windows 8.1.
Thanks, in advance.

The easiest way is to do this (this assumes some technical knowledge as well as access to the currently installed operating system and the 64bit install files)
1: launch diskpart from run or cmd
2: select the current OS disk using "select disk 0"
3: select the current OS volume using "select partition x" where x is the number of partition (you can use "list partition" to see all current partitions)
4: enter "shrink minimum=xxxxx" where xxxxx is the size in megabytes you want to new OS to have
5: Enter "create partition primary"
6: Enter "format quick fs=ntfs label="Windows x64""
7: Enter "assign letter y"
8: select your current system partition using "select partition x" where x is the number of partition. If you have a UEFI install on a GPT disk, this partition will be formatted in fat32. Otherwise, it will be a 100mb NTFS partition
9: Enter "assign letter s"
10: exit diskpart, and open up an administrator cmd prompt
11: Enter "dism /get-imageinfo /imagefile:e:\sources\install.wim" where e: is the drive letter that you have your .iso mounted in. If you have the iso extracted, you can just point to the current extracted area then \sources.install.wim. This will
show you a list of indexes that the .wim file supports. A standard retail version of the .iso will have Windows 8 Pro be index 1. If it is not, just change the index number in the next command.
12: Enter "dism /apply-image /imagefile:e:\sources\install.wim /index:1 /applydir:y:"
13: Enter "bcdboot y:\windows /s s: /f UEFI" (if you are using a MBR disk and not UEFI with a GPT disk, enter /f BIOS instead)
14: Reboot, select the x64 partition in the menu that comes up, and you are good to go!
You can also just create a new partition using disk manager then boot to the x64 disk and install it to the new partition, but that runs the risk of accidentally installing over something that shouldn't be if you select the wrong disk.

HT201303 How can I add another credit card for making payment?

My country of origin is India but I couldn't link my UAE credit card with AppStore.

The only way to use an iTunes/App store front is to use a method of payment native to the store's country, with a billing address in that same country. Stores are country specific - always have been.
If you have suitable payment and billing information, then just change your store designation, and change it back when you get home - see http://support.apple.com/kb/ht6119

ADDING ANOTHER 4GB MODUAL..

Hi - I think I would only need to add another 4GB module for what I use my Macbook Pro for. I have read that this would reduce it's performance by about 15% as apposed to having 2 x 4GB module. Does this sound right to you. I can not afford 2 x 4GB modules. Has anyone added another 4GB and did this help?

MacBook Pro AD is here:
http://discussions.apple.com/category.jspa?categoryID=190
http://www.apple.com/support/macbookpro/

X-Fi Xtreme Audio & 4GB RAM issue - latest driver?

:X-Fi Xtreme Audio & >4GB RAM issue - latest driver?T Hi All,
Been using an X-Fi Xtreme Audio with 4GB RAM for ages, no issues.
I purchased and installed a zotac 9600 GT which has GB onboard ram, which works fine, but now my X-Fi has started causing general system instability. (processes using heaps of CPU time whilst apparently doing not much, jerky/slow adobe flash, distorted (slow-motion) audio at random times, etc etc.
In the support section here it says:
Audio issue from output from soundcard with computer having 4GB RAM:
<span class="text">
Keywords: <font>4GB ram, installation, xfi, x-fi
Summary: Customers with computers having <font>4GB or above of RAM and are experiencing audio issues, please download the latest driver for your sound card.
However... When this issue first came up I formatted my primary dri've, reinstalled the OS and downloaded the latest drivers for EVERYTHING. The problem has prevailed..
It was only yesterday that I tracked down this problem in the support section here, and tried to verify that my driver is indeed the latest. But device manager lists the driver as "6.0.0.209" when in the support section here the downloads are named ".xx.xxxx" or something. How can I confirm that I have the latest driver? In any case, I'm almost certain that I have the latest, and this issue is still occuring.
I have read in other forums that on other varients of my X-FI card, the latest drivers have not solved this problem either.. sorry I cant be more accurate than that.
For now, I have solved this problem by simply removing 2GB of ram from my PC. Obviously, I'd like to find a solution and put the other 2GB back in!
Thanks in advance for your help!

Could DanielK please mod this as well, so we can try them. Or Daniel, you could you please tell me how you modified the previous drivers from auzentech as I dont know how these CL drivers work and are modified. What is the inf in these drivers, and if you could tell me the deviceID?s of all the x-fi models, or atleast for x-fi xtreme music as it is my modell. Thx in advance!
EDIT:
I have modified the drivers, was not so hard after all. Im uploading the file now, which should have support for all X-FI cards thanks to Daniel's great job with the earlier version.
Upload finished in 4-5minutes. I will post with link soon to rapidshare!

How to use 6GB ram for 32bit archlinux

i got a 4GB ram for my laptop, but my system can only use only 3GB.
so i want to know how to use the extra memorys?
thankyou!
~ * free -t
total used free shared buffers cached
Mem: 3071692 1195184 1876508 0 56264 538992
-/+ buffers/cache: 599928 2471764
Swap: 1999868 0 1999868
Total: 5071560 1195184 3876376

graysky wrote:Stop using i686. Since you appear to be new, please use code tags when posting output of commands. It formats the output to a nice mono space font.
i'm sorry ok

New RAM for MSI H67MA-E35(B3)

Hi,
I am planning to buy a new pair of RAM for my MSI H67MA-E35(B3) motherboard as the GSkill Ripjaws X which I was using since 2012 finally gave up on me recently (and the GSkill service sucks in my country). I am looking forward to buy a new pair of Kingston HyperX FURY 4GB RAMs for my MoBo. Hence I'd like to know if there will be any issues in terms of compatibility and stability with my current config? If there are going to be any such issues, would you please recommend me a good pair of RAMs to get my system running again. My priorities are Reliability and Stability with good service backup.
An early response will be much appreciated.
Thanks

Use Corsair ram. A Vengeance or Vengeance Pro kit will fit your needs. An 8GB (2x4GB) DDR3 1600 kit would be fine. e.g.: CMZ8GX3M2A1600C8

I have one home computer and our household has 2 iphones. I am signed up on itunes and now my husband would like to have an account with itunes as well. Can there be two accounts for 2 users for itunes on one home computer? How do I add another account ?

I have one home computer and our household has 2 iphones. I am signed up on itunes and now my husband would like to have an account with itunes as well. Can there be two accounts for 2 users for itunes on one home computer? How do I add another account ?

Have a read here...
https://discussions.apple.com/message/18409815?ac_cid=ha
And See Here...
How to Use Multiple iDevices with One Computer

Add another 4gb ram for g6-2148tx

Similar Messages

Maybe you are looking for