Add Standby Server in OEM Grid.

Hi,
I need to add Standby Database in Oracle EM Grid.. it is 11g Emgrid.. Standby database 11.2.0.3 is one server another one server is in 10g.. i need to add both server to EM Grid... We didn't configure Dataguard Broker.. is there any way to configure without dataguard broker. i have tried in Primary server on emgrid on availability page for add standby link.. but it's not accepting sys password for standby.... Please Give me solution.. We need Sync alert between Primary and Standby through EM Grid
Regards,
Madhan

From your description I do not understand what you have (provide full version numbers not marketing labels for each one) and their operating systems. Also the full version of OEM Grid.
What edition do you have Standard or Enterprise?
Is the source database RAC or stand-alone?
Did you read any docs telling you how to configure the standby? Post a link so we know what you were trying to do.
And finally "it's not accepting" means what? That the server reboots? That it gives you an error message you didn't think important enough to post?
Here's what your post reads like to me:
I need to add a second car for my family .. it is a 2009 Honda. Standby car is a Subaru wagon. I need to have both. I didn't do anything with my insurance policy. I have tried to start the car but it doesn't start. Please give me a solution."
{code}
Which car? Is it out of gas or did you use the wrong key? How can we know if you don't tell us.
Please provide all of the information and we should be able to answer your question ... but for starters. Data Guard broker is only "required" for RAC clusters.

Similar Messages

Add WebLogic Domain to OEM Grid Control

On a host, say x, i have installed OEM grid Agent Version: 11.1.0.1.0. The host is listed on OEM grid control. On this host i have a weblogic domain version 10.3.3. Now i am trying to add this weblogic domain to OEM 11g grid control which is on a different host.
It gives the following error
Error: Failed to connect to agent x:3872
Failed to connect to agent x:3872. Reason: java.net.UnknownHostException: x.
Only an agent 11.1 or later can be used for finding targets.
How can i solve this?

bummer.. any response? I'm getting the same error now, and the documentation isn't all that clear gasp

Which? - License for OEM Grid Control or just the additional Packs and Add-Ins?

I took a look at the price list and I wanted to clarify the "Named User Plus". The Diagnostic and Tuning Packs are each shown as $100 for the named user. As a DBA, if I have a named user license for these two management packs, does this mean that I can manage as many databases as needed with these two management packs?

Wow, 25 separate dbcontrols sound like a nightmare.
By the way, our Oracle rep just happened to come here yesterday, and he validated what was said here.
You can install the Grid Control free; you simply un-check the Packs/Add-Ins during the install.
As I understand it, you would install the Grid Control Agent first on each server, then when you install Oracle RDBMS, the Universal Installer will detect the Agent and enable the Grid Control instead of the Database Control.
Then you install the OEM Grid Control repository and software on a separate server, and that is where you manage all of the Oracle RDBMS servers from.
He also said to use the highest version Grid Control Agents on the database servers and repository server and keep the versions of that software in sync, which is separate from the Oracle RDBMS version.

License for OEM Grid Control or just the additional Packs and Add-Ins?

I have searched the forums and found the link below in a discussion about the Enterprise Manager Grid Control, but nobody answered this question specifically:
Can you freely install and use the Grid Control (with no additional Packs or Add-Ins)? Or does the Grid Control itself require a license?
P.S. The price list linked here only displays prices for Grid Control Packs and Add-Ins:
www.oracle.com/corporate/pricing/eplext.pdf

Wow, 25 separate dbcontrols sound like a nightmare.
By the way, our Oracle rep just happened to come here yesterday, and he validated what was said here.
You can install the Grid Control free; you simply un-check the Packs/Add-Ins during the install.
As I understand it, you would install the Grid Control Agent first on each server, then when you install Oracle RDBMS, the Universal Installer will detect the Agent and enable the Grid Control instead of the Database Control.
Then you install the OEM Grid Control repository and software on a separate server, and that is where you manage all of the Oracle RDBMS servers from.
He also said to use the highest version Grid Control Agents on the database servers and repository server and keep the versions of that software in sync, which is separate from the Oracle RDBMS version.

How to add a new server to the grid control

Hi ,
OEM 10g grid control has already bee installed n our site . But I don't know how a add /configure a new sever / database into that . Do I need to install the agent software on the destination machine OR is there any way to add the new sever from the 10g grid control itself ... Please help me out . You can also revert me back on my id [email protected]
redgs
RAHUL

thnx for replying .
Could you please tell me the patch number that I need to download for OEM grid control 10.2.0.3 . Actually I searched for lot of docs . But didn't found doc regarding installation of oem agent and agent PATCH number .
So , Please revert back with necessary Patch number and all the steps that I need to be follow . Thanx in advance
regds
RAHUL

OEM grid 11 installation on windows server 2008

Hi ,
We have a 64 Bit windows 2008 server , on which we need to install OEM grid 11.
For this we will be using :
OEM 11 for windows 32 bit
Oracle 11gr2 windows 32 bit
Weblogic server 32 bit.
the instalation order would be :
1.Weblogic
2. Database
3. Grid
Please suggest if these are the right versions and also if its ok to install 32 bit versions on them ? since I read somewhere that 64 Bit Db wont be compatible with OEM and weblogic.
Thanks and Regards
KK

Hi Eric,
Thank you for the suggestion.
We have first installed the weblogic. Then the database and lastly the Grid.
While installing grid , it was stuck at the 12th Step which was configuring the Agent.
On checking metalink we came accross a note and followed the steps mentioned as it is.. So for the moment it was done..
But now everything is up , inspite of that the grid aint visible.
I am trying the following :
http://hostname.domainname:7799/em
and it just gives a blank image.
https://kr.forums.oracle.com/forums/thread.jspa?threadID=1103539 speaks of the same issue.. I am going through it now..
Regards
Kk

"Add Standby Database" wizard licensing

there is a wizard in grid control known as "Add Standby Database" does it require licesning ?
apparently this is missing in the EM dbconsole...
http://download.oracle.com/docs/cd/B28359_01/server.111/b28295/gui.htm#i1005702
Oracle Enterprise Manager Grid Control provides access to the complete set of Data Guard 10.2 features. Limited monitoring-only Data Guard functionality is available in Enterprise Manager Database Control.

user9198889 wrote:
there is a wizard in grid control known as "Add Standby Database" does it require licesning ?
apparently this is missing in the EM dbconsole...
http://download.oracle.com/docs/cd/B28359_01/server.111/b28295/gui.htm#i1005702
Oracle Enterprise Manager Grid Control provides access to the complete set of Data Guard 10.2 features. Limited monitoring-only Data Guard functionality is available in Enterprise Manager Database Control.It's not a licensing issue, it's an inherent limitation of dbcontrol. It (dbcontrol) works with a single database. To create/manage a DG setup, you have to be able to work with multiple databases, hence the only flavor of OEM that will do it is GC.

OEM GRID AGENT

hi,
I have already installed OEM 10g Grid Control OMS on my linux sever which also has EBS R12.1.
I want to manage our EBS 11i which resides on another server
I downloaded the Linux_Grid_Control_agent_download_10_2_0_2_0.zip file from OTN,
and put it to the target server and unzip it.
Then I runInstaller and choose add management server.
I followed this link for the agent install>
http://www.idevelopment.info/data/Oracle/DBA_tips/Enterprise_Manager/OEM_12.shtml#Install%20Management%20Agent%20%2810.2.0.5%29
But I got stuck up on the Screen Page for entry of
Management Service Host Name > server01.abc.com
Management Service Port > 4889I got error : The connection can not be established to Oracle Configuration Manager
Reason > Error connecting to server peer not authenticated
But in the server linux fire fox browser, I can access it using > http://server01.abc.com:4889/em
I can not understand why this simple thing to follow just stuck with this
Oracle Configuration Manager > There is a "Test Connection" button there.
And it will not pass over it. How do I test connection from the OS command prompt? What command does this
screen use to validate connection to the OMS server?
Did I miss someting ? a pre-requisite perhaps that is needed by this connection?
What do you mean by "peer authentication"?
Please help....
Thanks a lot,
Ms K

Hi;
Please check below and compare your steps wiht doc
Oracle Universal Installer please refer to section 3.3.4 of the the Enterprise Manager Grid Control Basic Installation and Configuration Guide available at:
http://www.oracle.com/technology/documentation/oem.html
Regard
Helios

New targets need to be added in OEM GRID

Hi Gurus,
I have OEM grid configured and added four targets in that GRID.
My question is,
1. is it possible to add SUN application server to the OEM target?
2. there are some middle ware utilities are running, I want the status of that utility/service. I mean if the service is down it must be notified. Is it possible to configure in OEM?
Please provide some light on this
-Thanks & Cheers
Antony

I have OEM grid configured and added four targets in that GRID.
My question is,
1. is it possible to add SUN application server to the OEM target?OEM supports IBM WebSphere Application Server, JBoss Application Server and Apache Tomcat. I am not sure about SUN application server.
To get complete list of targets supprted and plugin required , please check :
http://www.oracle.com/technology/products/oem/extensions/index.html
2. there are some middle ware utilities are running, I want the status of that utility/service. I mean if the service is down it must be notified. Is it possible to configure in OEM?
If plugin is available for that middleware then you can configure notification rule for that .
Otherwise you can create an OS script and call it in OEM . You can also configure an alert for that.
Regards
Rajesh

Sending Comparison Report from OEM Grid

Hi All
I have configured a job to compare a schema objects in two database. I used Grid Control's Change Manager for this. I want an email
to be sent me when ever a comparison job completes and this email should
contain the comparison report of the comparison. I need a report same as we use
to have in change manager which comes with Oracle Administration Client and
generates and HTML report of schema comparison. Can you please help me setting
this. I have already setup configuration of my mail server and email adderess
in my OEM Grid control.
Thanks

What you first need to do is set up a notification method.
Then you will need to set up your own notification schedule.
Then add the job you are wanting to run and be alerted on to the notification rules.
Then you will want to subscribe to that/those rules.
Then you will want to check the notification you wish to get in the job itself.

Error installing OEM Grid 10.2.0.1 on VM machine

Hello,
I am trying to install OEM Grid 10.2.0.4, instruction said to install 10.2.0.1 first and then patch up to 10.2.0.4. I am installing 10.2.0.1 on a VM machine, SUSE 9. Installation is going fine until "OMS Configuration". Error file in /u01/app/oracle/product/10.2.0/agent10g/cfgtoollogs/configToolfailedCommands is below and nothing else:
# Copyright (c) 1999, 2005, Oracle. All rights reserved.
oracle.sysman.emcp.agent.AgentPlugIn
Where do I begin to troubleshoot and then "Retry" the "OMS Configuration" step again? Thank you in advance.

What is VM machine ?
Your machine have hostname or hostname and virtual hostname?
Your server is add to DNS SERVER
Work nslookup IP and nslookup hostname?
What type of installation are you choose?
Grid control using new database or
grid control using existing database
The linux server have installed the patch requirements?
Tell me if the installer give you errors of linking librarys

Oracle ORA_16000 when trying to add standby instance to existing rac node

I attempted to use dbca to add a new standby instance to an existing cluster. The cluster is 4 nodes, Linux RHEL 5.3 Oracle 11.1.0.7. Also using ASM, asmlib, ocfs2 and shared block devices.
ASM instances are up and functional on all nodes. current config appears to be running normally and correctly.
I have a 4 instance database running on the cluster. I also have 3 physical standby active data guard instances running on 3 of the nodes. I wanted to add a new ADG instance to the 4th node.
While running dbca I received ORA-00604 and ORA-16000.
The active data guard database was open (read only) and redo apply was on. I am using data guard broker as well, but not grid control.
Does anyone have a procedure for adding an instance in this environment? Do I need to have the standby in mount state? If dbca won't work does anyone have a manual procedure for adding a new instance?
Thanks

zulo
Let's say you adding node nusclust160## to you existing cluster and dbca is a pain to use.
Extend clusterware to the nusclust160## server.
re: Page 64 of Oracle® Clusterware Administration and Deployment Guide 11g Release 1 (11.1)
1a.
Add undo tablespace to support additional node.
Re-check space for DATA1 on nusclust16007 and /dbdata/ORADB on sun16109.
As of Thursday, May 21, 2009 the DATA1 asm group has 53,584M free.
As of Thursday, May 21, 2009 the /dbdata/ORADB has 77G free.
In a separate terminal window on nusclust16007 run the following in sqlplus
CREATE UNDO TABLESPACE UNDOTBS4 datafile '+DATA1' SIZE 13300M AUTOEXTEND ON ;
This will take a long time to create this tablespace. Please minimize the window after submitting the ddl and move on to the next step.
1b.
Insure .bash_profile on nusclust160## should look like this:
vi .bash_profile
export ORACLE_HOSTNAME=nusclust160##
export ORACLE_SID=ORADB4
export ORA_CRS_BASE=/apps/ocr/oracle
export ORACLE_BASE=/apps/dbs/oracle
export PATH=/usr/ccs/bin:/usr/X/bin:/usr/bin:/usr/sfw/bin:/usr/sbin:/usr/local/bin
export server=`uname -n`
export PS1="$ORACLE_SID@$HOSTNAME >"
alias cls='clear'
alias More='more'
alias ll='ls -lt | more'
Gather IP addresses for fourth node from /etc/hosts:
222.65.125.### nusclust160##
222.65.125.### nusclust160##-vip
10.333.248.### nusclust160##-priv
2. Start Oracle Universal Installer:
Go to CRS_home/oui/bin and run the addNode.sh script on one of the existing
nodes. Oracle Universal Installer runs in add node mode.
The Oracle inventory on nusclust16007, nusclust16008, and nusclust16036 are found under:
/home/oracle/oraInventory
Use a X windows enabled session (The OUI takes 33 minutes)
cd /apps/ocr/oracle/product/11.1.0/crs/oui/bin
./addNode.sh
a. In the first screen specify a new node as :
Public Node Name:          nusclust160##
Private Node Name:     nusclust160##-priv
Virtual Host Name:     nusclust160##-vip
If you receive the error:
" tar. ./bin/racgvip.orig: Permission denied"
Do the following:
cd /apps/ocr/oracle/product/11.1.0/crs/bin
ls -al racgvip.orig
paste here:
chown root:oinstall racgvip.orig
chmod 771 racgvip.orig
should now show:
-rwxrwx--x 1 root oinstall 19213 Feb 11 08:36 racgvip.orig
As root:
a.
On nusclust160##:
cd /home/oracle/oraInventory
./orainstRoot.sh
b.
On nusclust16007:
cd /apps/ocr/oracle/product/11.1.0/crs/install
./rootaddnode.sh
clscfg: EXISTING configuration version 4 detected.
clscfg: version 4 is 11 Release 1.
Attempting to add 1 new nodes to the configuration
Using ports: CSS=49895 CRS=49896 EVMC=49898 and EVMR=49897.
node <nodenumber>: <nodename> <private interconnect name> <hostname>
node 4: nusclust160## nusclust160##-priv nusclust160##
Creating OCR keys for user 'root', privgrp 'root'..
Operation successful.
/apps/ocr/oracle/product/11.1.0/crs/bin/srvctl add nodeapps -n nusclust160## -A nusclust160##-vip/255.255.255.224/bge0
c.
On nusclust160##:
cd /apps/ocr/oracle/product/11.1.0/crs/
./root.sh
WARNING: directory '/apps/ocr/oracle/product/11.1.0' is not owned by root
WARNING: directory '/apps/ocr/oracle/product' is not owned by root
WARNING: directory '/apps/ocr/oracle' is not owned by root
Checking to see if Oracle CRS stack is already configured
OCR LOCATIONS = /raw/ocr/ocrconf1,/raw/ocr/ocrconf2
OCR backup directory '/apps/ocr/oracle/product/11.1.0/crs/cdata/rac_cluster' does not exist. Creating now
Setting the permissions on OCR backup directory
Setting up Network socket directories
Oracle Cluster Registry configuration upgraded successfully
The directory '/apps/ocr/oracle/product/11.1.0' is not owned by root. Changing owner to root
The directory '/apps/ocr/oracle/product' is not owned by root. Changing owner to root
The directory '/apps/ocr/oracle' is not owned by root. Changing owner to root
clscfg: EXISTING configuration version 4 detected.
clscfg: version 4 is 11 Release 1.
Successfully accumulated necessary OCR keys.
Using ports: CSS=49895 CRS=49896 EVMC=49898 and EVMR=49897.
node <nodenumber>: <nodename> <private interconnect name> <hostname>
node 1: nusclust16007 nusclust16007-priv nusclust16007
node 2: nusclust16008 nusclust16008-priv nusclust16008
node 3: nusclust16036 nusclust16036-priv nusclust16036
clscfg: Arguments check out successfully.
NO KEYS WERE WRITTEN. Supply -force parameter to override.
-force is destructive and will destroy any previous cluster
configuration.
Oracle Cluster Registry for cluster has already been initialized
Startup will be queued to init within 30 seconds.
Adding daemons to inittab
Expecting the CRS daemons to be up within 600 seconds.
Cluster Synchronization Services is active on these nodes.
nusclust16007
nusclust16008
nusclust16036
nusclust160##
Cluster Synchronization Services is active on all the nodes.
Waiting for the Oracle CRSD and EVMD to start
Oracle CRS stack installed and running under init(1M)
4. After this is done crs_stat -t will show nusclust160## in the crs i.e.
I see:
Name Type Target State Host
ora....160##.gsd application ONLINE ONLINE sun...160##
ora....160##.ons application ONLINE OFFLINE
ora....160##.vip application ONLINE ONLINE sun...160##
Do not be concerned about ora.nusclust160##.ons being OFFLINE, as that will be fixed shortly in a step that follows this one.
5. As oracle :
On nusclust16007:
cd /apps/ocr/oracle/product/11.1.0/crs/bin
./racgons add_config nusclust160##:6251
This should take about one second to run.
If it says that it has already been added to the OCR you are fine.
If it hangs, you may need to reboot all servers to clear this issue.
6. Insure new node is properly added to ocr by running
On nusclust16007:
ocrdump
Check for the entries that show:
[DATABASE.ONS_HOSTS.nusclust160##.PORT]
ORATEXT : 6251
7. Check that your cluster is integrated and that the cluster is not divided into
partitions by completing the following operations:
On nusclust16007:
cd /apps/ocr/oracle/product/11.1.0/crs/bin
./cluvfy comp clumgr -n all -verbose
Should see Verification of cluster manager integrity was successful.
8.
Use the following command to perform an integrated validation of the Oracle
Clusterware setup on all of the configured nodes, both the preexisting nodes
and the nodes that you have added:
AS oracle on nusclust16007:
cluvfy stage -post crsinst -n all -verbose
Post-check for cluster services setup was successful.
good: Post-check for cluster services setup was successful.
9.
On nusclust160## as oracle run the following:
cd /apps/ocr/oracle/product/11.1.0/crs/bin
./crs_stat -t | grep OFFLINE
If you see this:
ora.nusclust160##.ons application ONLINE OFFLINE
then run this:
./crs_start -all
After:
./crs_stat -t
ora.nusclust160##.ons application ONLINE ONLINE nusclust160##
If you see the above then you can move on the next step.
Adding database binaries to the nusclust160## server and setting up the listener.
1.
From nusclust16007:
Open an X window (The OUI part takes 13 minutes)
cd /apps/dbs/oracle/product/11.1.0/db_1/oui/bin
./runInstaller -addNode ORACLE_HOME=/apps/dbs/oracle/product/11.1.0/db_1 $*
You should get a prompt to specify a new node, in this case you should see nusclust160## where you will need to put a check mark beside it.
2.
from nusclust160##:
Eventually you will be prompted to run the following as root on the new node
On nusclust160##
cd /apps/dbs/oracle/product/11.1.0/db_1
./root.sh
Running Oracle 11g root.sh script...
The following environment variables are set as:
ORACLE_OWNER= oracle
ORACLE_HOME= /apps/dbs/oracle/product/11.1.0/db_1
Enter the full pathname of the local bin directory: [usr/local/bin]:
Copying dbhome to /usr/local/bin ...
Copying oraenv to /usr/local/bin ...
Copying coraenv to /usr/local/bin ...
Creating /var/opt/oracle/oratab file...
Entries will be added to the /var/opt/oracle/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root.sh script.
Now product-specific root actions will be performed.
Finished product-specific root actions.
3. verification
Now set up the .bash_profile and .asm profile to on nusclust160## to support new ORADB4 and +ASM4 instances for the oracle userid.
On nusclust160##:
cp .bash_profile .bash_profile.bak
On nusclust16007:
sftp nusclust160##
put .bash_profile
On nusclust160##:
vi .bash_profile
change ORALCE_SID to ORADB4
cp .bash_profile .asm
vi .asm
change ORALCE_SID to +ASM4 in .asm file
which sqlplus
Should show the path below is $PATH environmental variable is set correctly.
/apps/dbs/oracle/product/11.1.0/db_1/bin/sqlplus
On nusclust160##:
oifcfg getif
This should show:
ce4 10.333.248.192 global cluster_interconnect
ce5 222.65.125.128 global public
4.
Run Netbackup Oracle Agent link script.
As oracle make sure ORACLE_HOME is fined.
env | grep ORACLE_HOME
then
cd /usr/openv/netbackup/bin/
./oracle_link
ls -al $ORACLE_HOME/lib/libobk.so
should show:
/apps/dbs/oracle/product/11.1.0/db_1/lib/libobk.so -> /usr/openv/netbackup/bin/libobk.so64.1
5.
On the target node, run the Net Configuration Assistant (NETCA) to add a
listener. Add a listener to the target node by running NETCA from the target node and
selecting only the target node on the Node Selection page.
I shall do the following on nusclust160## using X Windows
Now before I do this I see:
crs_stat -t
ora.nusclust160##.gsd application ONLINE ONLINE nusclust160##
ora.nusclust160##.ons application ONLINE ONLINE nusclust160##
ora.nusclust160##.vip application ONLINE ONLINE nusclust160##
Connect to nusclust160## and open up X windows session.
netca
Choose Cluster configuration.
select nusclust160## as the node to configure.
Choose Listener configuration, then Add.
When it prompts you for a listener name choose LISTENER as it will append _NUSCLUST160##(server name) to end of the LISTENER name to make a complete listener name.
At this point you will have listener to support the new node in the crs.
now
crs_stat -t
will show:
ora....0#.lsnr application ONLINE ONLINE nusclust160##
ora.nusclust160##.gsd application ONLINE ONLINE nusclust160##
ora.nusclust160##.ons application ONLINE ONLINE nusclust160##
ora.nusclust160##.vip application ONLINE ONLINE nusclust160##
At this point the necessary crs entries for gsd, ons, vip, and the listener on nusclust160## all we need now are the ORADB4 and +ASM4 instances added.
III. 7/11/2009 7:40 AM Sat [120 min] NTTA DBA
Use NON dbca method to create additional instances on the nusclust160## server. This will involve a complete shutdown of all RAC instances.
1.
Undo tablespace creation was taken care of in Step I,1. Check on the progress of the creation of tablespace UNDOTBS4 in the minimized window. Should see tablespace on primary and physical standby databases.
2. First we shall set up the +ASM4 instance on nusclust160## and add it to the cluster.
On nusclust160##
cd $ORACLE_HOME/dbs
vi init+ASM4.ora
# Copyright (c) 1991, 2001, 2002 by Oracle Corporation
# Cluster Database
cluster_database=true
cluster_database_instances=6
# Miscellaneous
diagnostic_dest=/apps/dbs/oracle
instance_type=asm
# Pools
large_pool_size=12M
asm_diskgroups='DATA1','ARCH','REDO1','REDO2'
asm_diskstring='/raw/asm'
+ASM1.instance_number=1
+ASM2.instance_number=2
+ASM3.instance_number=3
+ASM4.instance_number=4
3.
On nusclust16007
cd $ORACLE_HOME/dbs
sftp nusclust160##
put orapw+ASM1 /apps/dbs/oracle/product/11.1.0/db_1/dbs
put orapwORADB1 /apps/dbs/oracle/product/11.1.0/db_1/dbs
4.
On nusclust160##
cd $ORACLE_HOME/dbs
cp orapw+ASM1 orapw+ASM4
cp orapwORADB1 orapwORADB4
5.
On nusclust160##
cd $HOME
. ./.asm
sqlplus '/ as sysasm'
startup
create spfile from pfile='/apps/dbs/oracle/product/11.1.0/db_1/dbs/init+ASM4.ora' ;
shutdown immediate ;
startup
show parameters spfile
6. Now that we have a running asm instance add it the cluster.
On nusclust160##
srvctl add asm -n nusclust160## -i +ASM4 -o /apps/dbs/oracle/product/11.1.0/db_1
srvctl enable asm -n nusclust160## -i +ASM4
7. Now that we have an asm instance let's set up a database instance.
On nusclust16007/ORADB1 :
alter system set cluster_database_instances=6 scope=spfile ;
alter system set instance_name=ORADB4 scope=spfile sid='ORADB4' ;
alter system set instance_number=4 scope=spfile sid='ORADB4' ;
alter system set local_listener=LISTENER_ NUSCLUST160## scope=both sid='ORADB4' ;
alter system set thread=4 scope=both sid='ORADB4' ;
alter system set undo_tablespace=UNDOTBS4 scope=both sid='ORADB4' ;
alter database add logfile thread 4 group 28 ('+REDO1', '+REDO2' ) size 100M ;
alter database add logfile thread 4 group 29 ('+REDO1', '+REDO2' ) size 100M ;
alter database add logfile thread 4 group 30 ('+REDO1', '+REDO2' ) size 100M ;
alter database add logfile thread 4 group 31 ('+REDO1', '+REDO2' ) size 100M ;
alter database enable public thread 4;
Need to add 5 groups to support standby
So at the end of the day 900M will be added to REDO1(29,577M free) and 900M will be added to REDO2 (29,577M free).
8. Set up init.ora, listener.ora, and tnsnames.ora for ORADB4 on nusclust160##.
a. init.ora set up
cd $ORACLE_HOME/dbs
vi initORADB4.ora
SPFILE='+DATA1/ORADB/spfileORADB.ora'
b. add entries to tnsnames.ora:
ORADB4 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORADB)
(INSTANCE_NAME = ORADB4)
ORADB =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust16007-vip)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust16008-vip)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust16036-vip)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
(LOAD_BALANCE = yes)
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORADB)
LISTENERS_ORADB =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust16007-vip)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust16008-vip)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust16036-vip)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
LISTENER_NUSCLUST160## =
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
ORADB_PRIM =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust16007-vip)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust16008-vip)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust16036-vip)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
(LOAD_BALANCE = yes)
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORADB)
c. add entries to listener.ora, The entries for most of this file should be set already, just insure modifications that need to be made are made.
SID_LIST_LISTENER_NUSCLUST160## =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = /apps/dbs/oracle/product/11.1.0/db_1)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = ORADB)
(ORACLE_HOME = /apps/dbs/oracle/product/11.1.0/db_1)
(SID_NAME = ORADB4)
LISTENER_NUSCLUST160## =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = NUSCLUST160##-vip)(PORT = 1521)(IP = FIRST))
(ADDRESS = (PROTOCOL = TCP)(HOST = 222.65.125.###)(PORT = 1521)(IP = FIRST))
9. Reload the listener.
lsnrclt
set current_listener LISTENER_NUSCLUST160##
reload
exit
10. Check audit trail, add instance to cluster, and start db instance.
a.
Check for audit directory and start the instance.
/apps/dbs/oracle/product/11.1.0/db_1/rdbms/audit
If this audit trail directory does not exist then create it.
b.
srvctl add instance -d ORADB -i ORADB4 -n nusclust160##
srvctl modify instance -d ORADB -i ORADB4 -s +ASM4
srvctl enable instance -d ORADB -i ORADB4
Will probably show: PRKP-1017 : Instance ORADB4 already enabled.
c.
sqlplus '/ as sysdba'
startup
**Because the cluster_database_instances parameter requires the complete shutdown of all instances in the cluster, you might have an issue when it attempts to start the instance. If you receive an error then run:
srvctl stop database -d oradb
sqlplus '/ as sysdba'
startup
shutdown
srvctl start database -d oradb
shutdown
srvctl start instance -d ORADB -i ORADB4 -o open
11.
Modify spfile of ASM1, ASM2, +ASM3
On nusclust16007
. ./.asm
sqlplus '/ as sysasm'
alter system set instance_number=4 scope=spfile sid='+ASM4' ;
On nusclust16008
. ./.asm
sqlplus '/ as sysasm'
alter system set instance_number=4 scope=spfile sid='+ASM4' ;
On nusclust16036
. ./.asm
sqlplus '/ as sysasm'
alter system set instance_number=4 scope=spfile sid='+ASM4' ;
b Modify tnsnames.ora on nusclust nusclust16007, nusclust16008, and nusclust16036
On nusclust16007
ORADB4 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORADB)
(INSTANCE_NAME = ORADB4)
Add the following line to the ORADB alias:
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
Add the following line to the LISTENERS_ORADB alias:
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
Add the following line to the ORADB_PRIM alias:
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
On nusclust16008
ORADB4 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORADB)
(INSTANCE_NAME = ORADB4)
Add the following line to the ORADB alias:
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
Add the following line to the LISTENERS_ORADB alias:
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
Add the following line to the ORADB_PRIM alias:
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
On nusclust16036
ORADB4 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORADB)
(INSTANCE_NAME = ORADB4)
Add the following line to the ORADB alias:
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
Add the following line to the LISTENERS_ORADB alias:
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
Add the following line to the ORADB_PRIM alias:
(ADDRESS = (PROTOCOL = TCP)(HOST = nusclust160##-vip)(PORT = 1521))
c Add standby logs on primary to support 4th node.
alter database add standby logfile thread 4 group 32 ('+REDO1', '+REDO2' ) size 100M ;
alter database add standby logfile thread 4 group 33 ('+REDO1', '+REDO2' ) size 100M ;
alter database add standby logfile thread 4 group 34 ('+REDO1', '+REDO2' ) size 100M ;
alter database add standby logfile thread 4 group 35 ('+REDO1', '+REDO2' ) size 100M ;
alter database add standby logfile thread 4 group 36 ('+REDO1', '+REDO2' ) size 100M ;
12.
Test the cluster to make sure everything is set up correctly.
a. Shutdown resources.
On nusclust16007:
emctl stop dbconsole
ps -ef | grep perl
ps -ef | grep agent
ps -ef | grep java
On nusclust16008:
emctl stop dbconsole
On nusclust16036:
emctl stop dbconsole
On nusclust16008:
cd $HOME
. ./.rman
cd scripts
./go
shutdown immediate
cd $HOME
. ./.bash_profile
srvctl stop database -d oradb
crs_stop -all
crs_stat -t
b. Startup resources
On nusclust16007:
cd $HOME
. ./.bash_profile
crs_start -all
crs_stat -t
The command above should show everything up and running.
ocrcheck
On nusclust16008:
cd $HOME
. ./.rman
cd scripts
./go
startup
On nusclust16007:
emctl start dbconsole
On nusclust16008:
emctl start dbconsole
On nusclust16036:
emctl start dbconsole
How does that work for you?
-JR jr

Steps to add cluster instances/database to GRID 10gr1

Hi
I need to add cluster databases(10gR2) to OEM Grid (10gR1).
Guys can some one help me with steps / any link?
I got good doc from help link from OEM Help itself. How ever I here we need to do some thing with srvctl to keep quite CRS. if you any one know better/best please stop by and give me some instructions.
Thanks

Hi
I am also not very sure about that SRVCTL. I just heard from some other person. If we do not change some parameters while registering with service control then CRS work creazy. I am not sure what that mean is.
I do went to help document. There it is asking me to list 2 cluster servers to note in TARGET.xml. I never tried, one that I ask to work is prod so I do not want to take any kind of risk, so, prior to put that server on GRID, I want to get some BONDs give some suggestions.
How ever currently we do not have any CRS issues.
Regards,
RK.

How to install OEM Grid Control R2 on RHEL AS4 (AMD64/EM64T)

Hi all,
I was able to install the Oracle Application Server (Infrastructure and BI and Forms) successfully on the another machine with the same specs. The application I installed on the 64-bit machine is a 32-bit Oracle Application Server.
Now, I tried to install the OEM Grid Control R2 (another 32-bit Oracle Software) on an identical 64-bit machine but had no luck. Ran linux32 bash before trying the install.
I always get the error "error in invoking target 'dm_on ioracle' of makefile 'OH/db10g/rdbms/lib/ins_rdbms.mk".
Please help me/guide me in this install if it is at all possible.
Thanks and regards,
Mike

Did you read the installation docs?
Did you look up trying to do this on metalink before proceeding?

OEM grid 10g installation steps on RHEL 5.4

Please provide the steps and note ids for OEM grid 10g/11g installation on linux 5
we are on 2 node RAC running on Red Hat Enterprise Linux Server release 5.4 (Tikanga)
uname -a
Linux clelx062ptlge.penske.com 2.6.18-164.el5 #1 SMP Tue Aug 18 15:51:48 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux
Please provide what are the packages and kernal parameters we have to install/set at OS level.
Any white papers will be very helpful.
--Srikanth

dm_ptldba wrote:
Please provide the steps and note ids for OEM grid 10g/11g installation on linux 5
we are on 2 node RAC running on Red Hat Enterprise Linux Server release 5.4 (Tikanga)
uname -a
Linux clelx062ptlge.penske.com 2.6.18-164.el5 #1 SMP Tue Aug 18 15:51:48 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux
Please provide what are the packages and kernal parameters we have to install/set at OS level.
Any white papers will be very helpful.
--SrikanthHere are the steps of installing Grid Control on Linux
http://www.oracle-base.com/articles/10g/Oracle10gR2GridControlInstallationOnRedHatAndCentOS.php
http://www.oracle-base.com/articles/11g/GridControl11gR1InstallationOnOEL5.php
I'm also currently working on video tutorial of installing Grid Control and Deploying agents. So I hope it will be ready for the next week, so just keep visiting video tutorial page of my blog and you'll find it there soon :)
http://kamranagayev.wordpress.com/oracle-video-tutorials/

Add Standby Server in OEM Grid.

Similar Messages

Maybe you are looking for