Adding a new Airport Extreme to existing network?

Hi, I just bought an Airport Extreme, which I want to use in my apartment to replace my existing Airport Express (802.11g) network. Is there an easy way to do this without having to reset all my devices that use the network?
I have a TV, receiver, Blu ray player, two laptops, two iPhones and an iPad, all of which would need to be reconfigured if I just scrap the existing network in favor of the new device's new network. (And it's really annoying to set up the network on the home theater stuff!)
Am I just being lazy, and I should just start a new network from scratch?
Thanks in advance for any help or suggestions.

Whenever replacing network equipment, it is always a good idea to start from scratch. What you may save during the initial setup may be lost with the time you will spend hunting down why things are not quite working right later.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Disconnect the 802.11g AirPort Express Base Station (AX) from the Internet broadband modem.
(OPTIONAL) While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Connect the new 802.11n AirPort Extreme Base Station (AEBSn), using the same Ethernet cable that was used for the AX. Make sure to connect the cable to the AEBSn's WAN (circle-of-dots) port.
Temporarily connect your Mac Pro to one of the available LAN (opposing arrows) ports on the AEBSn. Of course, if you intend on leaving the Mac Pro connected by Ethernet, then just leave the Ethernet connection as is after the setup is complete.
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AEBSn; wait at least 5-10 minutes. Note: The AEBSn's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
In this basic configuration, the AEBSn will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

Similar Messages

HT4145 Does the new Airport Extreme allow "guest network" setup across all my Airports on my network? I have 1 Airport as a router and 6 others as WAP's (bridged)

Does the new Airport Extreme allow "guest network" setup across all my Airports on my network? I have 1 Airport as a router and 6 others as WAP's (bridged)

I assume that all of your WAPs are hard wired on the network.
If.....all of your WAPs are simultaneous dual band Apple AirPort devices like an AirPort Extreme or new AirPort Express.....and.....you have firmware version 7.6.3 (now 7.6.4) installed on all the AirPorts.....and.....you use AirPort Utility 6.3.1 to configure the devices......in theory.....it should work.
I don't have 6 WAPs, but I do have 3 and the network works perfectly allowing extension of both the "main" and "guest" network.

Trouble adding Airport Extreme to existing network using Netgear N150 network

I'd appreciate any help with my situation.
I don't know all of the technical terms, but basically most of my house is hardwired with CAT-5 cables. I have a broadband internet modem hooked up to some sort of switch, then a Netgear N150 router which is plugged into an ethernet socket in one of the rooms. Right now there is limited wireless access in certain parts of the house. I was hoping ideally to use the Airport Extreme to widen my existing internet coverage, but thought that I should first try to set it up as the primary router so I wouldn't run into any compatibility issues. However, because my Imac is pretty old, I was unable to set up the Extreme via my Imac as the Airport Utility software was out-of-date, and the link to update the software was non-functional. What I ended up having to do was temporarily plug my Netgear router back in, go to a different room, plug my Extreme into an ethernet socket, then configure the Extreme using an Ipad which was connected wirelessly to my Netgear network. However, when I then went to replace the Netgear router with the Extreme base station, my Ipad and Iphone could not connect to the new Extreme network. I do SEE it, but I keep getting the spinning spokewheel and it never connects. The odd thing is that I CAN connect to the Extreme network with my Imac.
I have tried multiple times to reset the Extreme, my Ipad, and the Netgear router, all to no avail. I have the latest software for the Extreme as well as for the Airport Utility. I've also tried playing with a few different combinations of both routers plugged in, 1 router by itself, and various settings on the Extreme. Right now I have the Extreme set up as a Bridge, and both routers plugged directly into the wall in separate rooms, but right now the only way I can access the internet is via my old Netgear network.
THANKS in advance for advice!

I have a broadband internet modem hooked up to some sort of switch,
Can you provide the make and model of the modem? Depending on the type of modem this might be, the Ethernet switch may need to come after the Netgear router, not between the modem and the Netgear router.

Airport Extreme in existing network

Hi!
I have installed 4 Airport Extreme in an existing network enviroment.
The problem is that the APs makes it own subnet. When connected to wlan it gets 10.0.1.x addresses and when connected to wired lan 10.0.0.x.
I think this is a setting in AP1 wich is connected via lan. Does anyone know what is wrong in the setup??
Thanks ina advance!

You need to configure the AirPort Extreme as a "bridge"
Open AirPort Utility - Manual Setup
Click the Internet icon
Connection Sharing = Off (Bridge Mode)
Update to save new settings

New Airport Extreme N wireless network setup questions (WDS, D-Link)

I have finally been able to set up my Airport Extreme N network after numerous attempts over the last few weeks. I was getting a very weak signal in front of the house where my wife's G4 is connected wireless to an old Airport card and where all the systems (XBOX 360; Wii and PS3) are also wirelessly hitting the network.
The current configuration is as follows: In the office in the back of the house I have an Airport Extreme N basestation connected to the cable modem and have three workstations (One Mac and two PCs) wired to it. I set up a WDS network, so I set up the Airport Expresses as remotes. In the living room I have another Airport Extreme N basestation (as a remote as well) that is hooking up to the XBOX 360, Wii and PS3. I have enabled WEP security (not effecting the XBOX 360 since it is now "wired"). Here is the weird thing - I have a PC laptop with a D-Link Xtreme N card ( DWA-652) that cannot connect to the network. I enter the WEP password but it does not connect. Am I missing something on the basestation setup? Do I need to add the MAC address of the card anywhere. When I use the laptop's built in wireless it connects with no problem. By creating a WDS network did I disable the n functionality of the base station(s)? I am a lttle condused.
Also, prior to going to an all Apple wireless network setup, I bought the D-Link Xtreme N Gigabit Router (DIR-655). I was regretfully about to return it to Best Buy but I had an idea which may or may not work. I know that the D-Link does not support WDS but if I was to set it up as the main router and added the "main" Airport basestation as a wired bridge could I maintain the WDS network? The reason I ask this is because I would love to keep the gigabit for the wired machines in the office. Also, I am wondering if the D-Link notebook card is incompatible with the Airport network.
All I know is that I have spent alot of money and sleepless nights just trying to set this network up but thankfully Best Buy has a thirty day return policy so I will return what I can't use.
I appreciate any help and advice anyone can give me.
Thanks.
V
MacPro Mac OS X (10.4.9)
MacPro Mac OS X (10.4.9)

Hello!
I have noticed that some manufacturers (Linksys and possibly D-LINK) only accept upper-case WEP keys only.
This drove me nuts when trying to integrate a Linksys PC PCMCIA card into my old "g" network.
As far as using WEP, it's bad and broken; but I understand that your choice of security is limited to the devices that you are trying to network.
For what it's worth, I have my network set up with the AEBS 'n' connected to my Cable Modem, with one of the ports going to a gigabit switch for my wired network. I then have two AirTunes set up as WDS extensions for music & Internet delivery to two separate areas. The AEBS 'n" serves up DHCP and routing for the entire network.
It works quite well; I get 54 mbits/sec for the two WDS AirTunes, and 145 mbits/sec to one of my ATV's. My gigabit wired machines see data rates of 15-27 MBytes/sec (depending on the type of transfer).
Good luck!

My power mac g4 with wireless card 801.11b cannot log into new AirPort Extreme 801.11ac network

everything worked until I upgraded to airport extreme. I used all same settings as with previous extreme al other items logged in to new network, but would not accept power mac. Apple wireless card 801.11b may not be able to communicate with AC standard. Can anyone suggest an upgrade card or means of getting the power mac on the wireless network to communicate with various wireless printers

Hello!
I have noticed that some manufacturers (Linksys and possibly D-LINK) only accept upper-case WEP keys only.
This drove me nuts when trying to integrate a Linksys PC PCMCIA card into my old "g" network.
As far as using WEP, it's bad and broken; but I understand that your choice of security is limited to the devices that you are trying to network.
For what it's worth, I have my network set up with the AEBS 'n' connected to my Cable Modem, with one of the ports going to a gigabit switch for my wired network. I then have two AirTunes set up as WDS extensions for music & Internet delivery to two separate areas. The AEBS 'n" serves up DHCP and routing for the entire network.
It works quite well; I get 54 mbits/sec for the two WDS AirTunes, and 145 mbits/sec to one of my ATV's. My gigabit wired machines see data rates of 15-27 MBytes/sec (depending on the type of transfer).
Good luck!

Adding new airport extreme to an existing airport express network...

i currently have a home airport network comprising two airport express units; one attached to the cable modem in the bedroom and the other downstairs in my study (extending the existing network and feeding a shared USB printer and airtunes speakers). i've recently bought an airport extreme, to improve network performance. i also plan to add a NAS in the next week or so.
ideally i'd like to situate the new airport extreme in the study, as i don't want to have to keep the NAS in my bedroom!
my question is this, if i add the new airport extreme to the existing airport network, will i see the benefit of the 802.11n connection, or should the extreme be set up as the primary base station?

... will i see slower transfer speeds (than if it was connected to the extreme) to / from the NAS when accessing it wirelessly from elsewhere in the house?
No. The transfer speed will be limited by the slowest connection, which is almost certainly your wireless connection speed.
If you buy a switch, buy a gigabit switch. Not because a slower one will limit your transfer speed, but because the Extreme is Gigabit and any newer equipment is likely to be as well. The advantage would only be relevant to the wired LAN.
The Express's Ethernet is not Gigabit but there is no reason for it to be, since it cannot connect to anything other than a slower wireless connection anyway.

Set up DynDNS access through existing network with new Airport Extreme

Hey everyone!
I just can't seem to figure out what I am doing wrong here...
I am working with an office network which was initially set up with a Linksys router and a separate Linksys hub connecting two Macs and a network printer in one particular room. We added several new iMacs and for ease of connectivity, decided to add a new Airport Extreme base as one of the new iMacs is acting as a server for a database the other new wireless iMacs connect to. Also, all the machines need access to the connected network printers connected in various parts of the office.
What we have now is the original Linksys router -> Linksys hub -> Airport Extreme. Everything seems to be working fine this way but I do believe that both the Linksys router AND the Airport Extreme are distributing IP addresses, which I'm thinking, could be the problem. I set up a DnyDNS account just fine, assigned port # 8080 on the server iMac and also opened port 8080 on both the Linksys and Airport Extreme. I still cannot get through to the server via DynDNS however.
I am wondering if I should turn off IP distribution on the Airport Extreme and let the Linksys router handle all that? The software that the other wireless iMacs run to access the database on the server depends on the server IP address too, so will this need to be changed if the Linksys is handling IP addressing? How does the hub affect any of this... does it change or interfere with the addressing in any way?
Thank in advance for any ideas or suggestions!

maxyourmacs, Welcome to the discussion area!
I am wondering if I should turn off IP distribution on the Airport Extreme and let the Linksys router handle all that?
Yes
The software that the other wireless iMacs run to access the database on the server depends on the server IP address too, so will this need to be changed if the Linksys is handling IP addressing?
Probably
How does the hub affect any of this... does it change or interfere with the addressing in any way?
It has no affect.

Extending an existing wireless network with a new Airport Extreme(802.11n)

Is it possible to extrend a existing wireless network comprised on a Airport Extreme (g) and a Airport Express with a new Airport Extreme (n) ? and possibly accesss an airdisk? Have tried settng channel to the same (1) but no worky.
I have had real problems (at least 2 hours with Apple Care to no avail) at getting the new Airport Extreme(n) to connect to the internet (Ozemail/iinet) with PPOE. Authentication when changed to occur at ADSL modem and produces no errors (green light) but no internet still through AE(n). Not Hardware either as both ADSL modem and AE(n) have been changed.
So as a last ditch attempt, thought I might try extending the preexisting network that works fine so I can access an AirDisk.
Any reponses appreciated.

Search this forum for "WDS". Since I am having massive problems myself right now, I can only tell you: Try the two methods mentioned in this thread:
http://discussions.apple.com/thread.jspa?threadID=944334&tstart=0
Maybe you're lucky!

How to add old airport extreme 11g to new airport extreme 11n to extend network?

I am trying to use my old Airport Extreme 11g to extend my wireless network from my newer Airport Extreme 11n. Are they compatible?

They are, but you may want to think twice before using this approach. The reasons are: 1) The extended network will only operate in the 802.11g Radio Mode, and 2) The overall bandwidth will be reduced by half for each base station added. Since this will be a "g" network, you'd be getting around 25-27 Mbps maximum of bandwidth.
If you still would like to pursue this, please check out the following Apple Support article for the details.

Configuring a new Airport Extreme with an existing Wireless Modem Router

I have an existing Wireless Modem Router (brand: Riger) and have an existing wireless network. Recently purchased an AirPort.
What is the best way to install a new AirPort Extreme? I know i have to connect the AirPort Extreme to the modem via ethernet cable.
Do i allow the AirPort to use the existing setting from my old wireless modem router?
Or do i create a new network with different name and password?
Anybody can help or show me where i can look up on this?
Thanks

Hello akramaziz. Welcome to the Apple Discussions!
Since the new 802.11n AirPort Extreme Base Station (AEBSn) will be connected to the existing Wireless Modem Router by Ethernet, it should be reconfigured as a bridge.
(ref: AirPort Utility > Select the AEBSn > Manual Setup > Internet > Internet Connection > Connection Sharing = Off (Bridge Mode))
As a bridge, the AEBSn will allow the existing router to continue to provide both NAT & DHCP services for all network clients.

How to connect old aiport express to my new Airport Extreme? My Ipad says "base station e5713b cannot be configured" and my AirPort tool on my PC will not permit me to add my new Airport Extreme network (no network names to choose from)

How to connect old aiport express to my new Airport Extreme?
I have a PC running with Win7 and just replaced my Jensen With a brand New Airport Extreme.
I have set up the Airport Extreme to the internet, Iphones and Ipads and it work as it should.
I have downloaded latest Version of Airport tool on my PC. In addition i have downloaded the airport tool for Ipad.
I have reset one of my airport Express and it now shows up both on the Ipad and on the PC airport tool.
My Ipad says "base station e5713b cannot be configured."
I have wired the airport Express to my Ethernet to be able to "see it" on my Airport tool.
My AirPort tool on the PC will not permit me to add the airport Express to my new Airport Extreme network (no network names on the drop-down list to choose from). I wished for an easy set-up, but nothing seems to be plug and play as the Commercial says.. can you please help me?
Sigve

Hi
Thanks for Swift reply.
Yep - I in fact have two A1088 and one A1264
I actually bought the new router because the Jensen
router always lost connection to the Airport Express after some hours or days. I
always needed to restart my Jensen to play music and that was driving my wife
mad. The hope was that the Extreme should fix this. Both A1088 have been set up
to only stream music to two of my stereo amplifiers from my PC’s Itunes library.
Are the A1088 now useless?
The A1264 has been set up to feed internet into a Denon Reciever that needed Ethernet cable.
Please advise
Regards
Sigve

New Airport Extreme (Jan 2007) with Comcast Cable Network

Im a total NOOB. Please excuse my poor knowledge of Routers and the like.
I really need some advice from the MAC community to steer me in the right direction. I want to give as much information as possible in order for you folks to help me down the right path.
CURRENT SET UP:
(3) Apple Computers in 3 bedrooms. (1) iMac Core2 Duo, (1) iMac Core Duo, (1) eMac G4. All have built in wireless cards from Apple.
Broadband Cable Internet from Comcast. Cable comes from wall directly to a Motorolla Surf Board Wireless SBG900. The Wireless Motorolla Cable Modem sits on the floor in the corner of one bedroom. All 3 computers work perfect. Never drop a signal. All very fast connections. No Internet or sharing issues at all. I also decided to add the "Plug in" Airport Express. This has an HP Color Laser Jet Printer pluged into it via USB. All 3 computers print and share seamlessly to it. Set up is a breeze. No issues what so ever with anything.
QUESTIONS:
(1) Should I eveen bother with the New Airport Extreme Base Station or just leave everything as it is?
(2) Is there ANY benefit to adding a Airport Extreme Base Station? I'm I missing out on anything?
Please be honest. Anything wrong with my current setup?
Thanks.

I don't think there's anything wrong at all with what you've done. The bottom line is do YOU find any faults or disadvantages to your set up? As far as the new Extreme, things would just be alot faster (for those 802.11n enabled computers only, though)
Im a total NOOB. Please excuse my poor knowledge of
Routers and the like.
I really need some advice from the MAC community to
steer me in the right direction. I want to give as
much information as possible in order for you folks
to help me down the right path.
CURRENT SET UP:
(3) Apple Computers in 3 bedrooms. (1) iMac Core2
Duo, (1) iMac Core Duo, (1) eMac G4. All have built
in wireless cards from Apple.
Broadband Cable Internet from Comcast. Cable comes
from wall directly to a Motorolla Surf Board Wireless
SBG900. The Wireless Motorolla Cable Modem sits on
the floor in the corner of one bedroom. All 3
computers work perfect. Never drop a signal. All
very fast connections. No Internet or sharing issues
at all. I also decided to add the "Plug in" Airport
Express. This has an HP Color Laser Jet Printer
pluged into it via USB. All 3 computers print and
share seamlessly to it. Set up is a breeze. No
issues what so ever with anything.
QUESTIONS:
(1) Should I eveen bother with the New Airport
Extreme Base Station or just leave everything as it
is?
(2) Is there ANY benefit to adding a Airport Extreme
Base Station? I'm I missing out on anything?
Please be honest. Anything wrong with my current
setup?
Thanks.

New airport extreme network very slow

I just bought the latest AE base station dual band, but am having trouble with the speeds. We have on the network:
1 macbook pro, 1 windows pc, 2 ipads, 1 ipad mini, 1 kindle fire, 2 iphones, 2 ipods (wow we have a lot of products I just realized now that I am writing them all down) a Wii console and 1 mac desktop computer. Oh and I have an airport express in another room set up to extend the netowrk.
Not all of them are on the network simultaneously.
Using the Airport utility (windows version) I have set up the network trying different configurations. Currently I have it set up as:
Radio mode: automatic
Radio channel selection: automatic
wireless security: WPA2 Personal
network options are 5 Ghz is unchecked
country is US
multicast rate: low
transmit power: 100%
WPA Group Key Timeout: 2 hours
use wide channels is checked
All devices can connect to the net, but speeds are at old dial up levels and that of course was NOT my intention in getting the latest router.
Any advice from those who understand things like multicast rate?

You either have a defective base station, it is not set up properly, or there is some form of Wi-Fi interference that is preventing your new AirPort Extreme from providing a clean signal.
What make & model was the router that you are replacing with the 802.11ac AirPort Extreme?

How do I unhide my network which I recently set up with new Airport Extreme?

I recently set up my new Airport Extreme. Then realised my Canon MX 410 was not seeing it on wifi network. I've been told I need to unhide the AE so the printer can see it. However, when I go into Airport Utility it is not giving me the option to unhide. I have tried connecting ethernet cable to it & turning off wifi, but this does not help.. Any ideas people?
Thanks....

I've been told I need to unhide the AE so the printer can see it.
Advice likes this sounds good.....IF.....you previously enabled the option to "hide" your network. Chances are, you would know if you did do this, but if you are not sure, you can check to see if the network really is "hidden".
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon, then click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window
Click Wireless Options at the bottom of the window
If the network is hidden, you will see a check mark in the box next to Create Hidden Network. If the box is not checked, then your network is not hidden...so there is no way to "unhide" a network that is not hidden in the first place.....and you might want to contact Canon support for help on how to set up your printer.
If you do see that the box is checked, then remove the check mark to "unhide" your network, click Save, then click Update and allow a full minutre for the AirPort Extreme to restart.

Adding a new Airport Extreme to existing network?

Similar Messages

Maybe you are looking for