Adding a secondary wireless controller for redundancy (5508)
I need to add a secondary controller for redundancy (both controllers located in the same location, etc) This is a small wireless network of about 35 Aps. What I am trying to accomplish is to provide wireless connectivity in case the primary controller fails. Should I just need add the primary and secondary controller IP address to the Aps via the controller gui? Does anyone know about any documentation that I can read? Do I need to create a mobility group?
Any help would be greatly appreciated
Thanks,
marramix01
Here is the link to do the same!!
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008064a294.shtml
lemme know if htis answered ur question!!
Regards
Surendra
Similar Messages
-
Secondary Domain Controller Not Authenticating Domain Users
Hi.
I have a primary domain controller running Win Srv 2012 in USA and i added a secondary domain controller 2012 in the same domain from a different location India, through VPN.so that India user accounts can authenticate by the secondary DC instead of primary
DC USA
Installation & replication of AD went fine
India domain users login is damn slow.
When i ran the command echo %logonserver% from a india client machine,it displays the USA Primary DC name which means its authenticating the users from USA primary DC.
Preferred DNS for india client machine is Secondary DC IP and alternate is Primary DC IP USA.
Please find the dcdiag results below and any help much appreciated
Performing initial setup:
Trying to find home server...
Home Server = server2
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: INDIA\server2
Starting test: Connectivity
......................... server2 passed test Connectivity
Doing primary tests
Testing server: INDIA\server2
Starting test: Advertising
Warning: DsGetDcName returned information for \\server1.tst.mycompany.com, when we were trying to reach
server2.
SERVER IS NOT RESPONDING or IS NOT CONSIDERED SUITABLE.
......................... server2 failed test Advertising
Starting test: FrsEvent
......................... server2 passed test FrsEvent
Starting test: DFSREvent
There are warning or error events within the last 24 hours after th
replication problems may cause Group Policy problems.
......................... server2 failed test DFSREvent
Starting test: SysVolCheck
......................... server2 passed test SysVolCheck
Starting test: KccEvent
......................... server2 passed test KccEvent
Starting test: KnowsOfRoleHolders
......................... server2 passed test KnowsOfRoleHolders
Starting test: MachineAccount
......................... server2 passed test MachineAccount
Starting test: NCSecDesc
......................... server2 passed test NCSecDesc
Starting test: NetLogons
Unable to connect to the NETLOGON share! (\\server2\netlogon)
[server2] An net use or LsaPolicy operation failed with error 67,
......................... server2 failed test NetLogons
Starting test: ObjectsReplicated
......................... server2 passed test ObjectsReplicated
Starting test: Replications
......................... server2 passed test Replications
Starting test: RidManager
......................... server2 passed test RidManager
Starting test: Services
......................... server2 passed test Services
Starting test: SystemLog
A warning event occurred. EventID: 0xA004001B
Time Generated: 02/22/2015 17:10:30
Event String: Intel(R) 82574L Gigabit Network Connection
A warning event occurred. EventID: 0x000727A5
Time Generated: 02/22/2015 17:11:24
Event String: The WinRM service is not listening for WS-Manageme
An error event occurred. EventID: 0x0000271A
Time Generated: 02/22/2015 17:11:24
Event String:
The server {9BA05972-F6A8-11CF-A442-00A0C90A8F39} did not regist
A warning event occurred. EventID: 0xA004001B
Time Generated: 02/22/2015 17:12:41
Event String: Intel(R) 82574L Gigabit Network Connection
A warning event occurred. EventID: 0x000003F6
Time Generated: 02/22/2015 17:19:36
Event String:
Name resolution for the name mycompany.com timed out after none
A warning event occurred. EventID: 0x00001796
Time Generated: 02/22/2015 17:28:54
Event String:
Microsoft Windows Server has detected that NTLM authentication i
his server. This event occurs once per boot of the server on the first time
A warning event occurred. EventID: 0x000727A5
Time Generated: 02/22/2015 17:33:35
Event String: The WinRM service is not listening for WS-Manageme
A warning event occurred. EventID: 0x00001796
Time Generated: 02/22/2015 17:35:54
Event String:
Microsoft Windows Server has detected that NTLM authentication i
his server. This event occurs once per boot of the server on the first time
......................... server2 failed test SystemLog
Starting test: VerifyReferences
......................... server2 passed test VerifyReferences
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test CrossRefValida
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test CrossRefValida
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidat
Running partition tests on : tst
Starting test: CheckSDRefDom
......................... tst passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... tst passed test CrossRefValidation
Running enterprise tests on : tst.mycompany.com
Starting test: LocatorCheck
......................... tst.mycompany.com passed test LocatorChec
Starting test: Intersite
......................... tst.mycompany.com passed test IntersiteHi.
I have a primary domain controller running Win Srv 2012 in USA and i added a secondary domain controller 2012 in the same domain from a different location India, through VPN.so that India user accounts can authenticate by the secondary DC instead of primary
DC USA
Installation & replication of AD went fine
India domain users login is damn slow.
When i ran the command echo %logonserver% from a india client machine,it displays the USA Primary DC name which means its authenticating the users from USA primary DC.
Preferred DNS for india client machine is Secondary DC IP and alternate is Primary DC IP USA.
Firstly make sure that you have configured sites and subnets correctly. According to your information which you have two locations, you should have at least 2 sites and 2 subnets associated to them. If you have forgotten to configure subnets of India in your
site and services and assigned them to the India site you are experiencing this issue. Also make sure if clients in India has appropriate network connectivity to the domain controllers in India.
Mahdi Tehrani |
|
www.mahditehrani.ir
Please click on Propose As Answer or to mark this post as
and helpful for other people.
This posting is provided AS-IS with no warranties, and confers no rights.
How to query members of 'Local Administrators' group in all computers? -
Sh run on a wireless controller
Can someone please tell me how to do sh run on a 2000 controller?
thanks.Thanks for your response... The problem I am having is telnetting or sshing into the wireless controller...Does anybody happen to know what the default port (23, 22, etc)is that's opened on a wireless controller for the CLI access?
thanks. -
Can CSACSE-1113-K9 work as a Wireless Controller ?
Hi all,
Need to know that if I have a CSACSE-1113-K9 and also i have 20 units of AIR-LAP1242AG-A-K9.
Can i utilize the CSACSE-1113-K9 Appliance to as a Wireless Controller for the AIR-LAP1242AG-A-K9 ?
Thanks and waiting for feedback.
Md. Sariful Islam
+8801716631370Hi Sarifaul,
Where did you hear that there is an appliance can be configured to a WLC?
The WLC comes with its own hardware OR as a virtual machine image. The virtual WLC however has a lot of limitations.
So, like Scott answered you, the answer to your questoin is "No".
Amjad
Rating useful replies is more useful than saying "Thank you" -
We recently purchased a second 5508 wireless controller (both licensed for 100+ AP's). What is the easiest way to configure and add the second controller so I can split the load between the 2 controllers and provide failover capability? I do not want to run in an active/standby mode since that will effectively cut our AP capacity by half even with both controllers running.
Should I just manually configure the new controller (long and drawn out process to configure all the parameters), backup the current controller configuration and import to the second controller (then change the ip address) or is their an easier way to cause the two controllers to synchronize the configurations?
We are currently running 7.0.240.0 on our active controller and I would rather not upgrade it until we get the new controller online so I can have less downtime and fail AP's between controllers.
What can you recommend?
JimI'm assuming then, when I update the software on the controllers I won't be able to choose which controller is primary for an AP anymore and will lose access to the 100 AP licenses (and the capability to have 100 AP's registered, 100 licenses on each Controller).
Read the Deployment Guide. It should mention that you can choose which controller is the "primary" and which one is the "secondary".
If I'm not concerned about quick failover can I still assign a primary and secondary controller for each AP and utilize all 200 AP licenses that are split between the 2 controllers?
You sure can. But this "old school" method is a very expensive method. Why? Because this means that you have two controllers with similar AP licenses. The newer AP SSO means one controller has a full license and the other has only an HA SSO license, which is a lot cheaper. -
Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9 (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number : 73-14034-04
PCA Assembly Number : 800-34273-05
PCA Revision Number : A0
PCB Serial Number : FOC16075VZ3
Top Assembly Part Number : 800-34284-03
Top Assembly Serial Number : FCZ1611W414
Top Revision Number : A0
Product/Model Number : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
ap-manager 2 untagged 209.165.200.231 Dynamic Yes No
management 1 untagged 209.165.200.230 Static Yes No
service-port N/A N/A 192.168.1.157 Static No No
virtual N/A N/A 1.1.1.1 Static No No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, GraciasHi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 management Disabled
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast
IP Status
c4:64:13:8f:93:40 209.165.200.230 hosp 0.0.0.0
Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address Port State Tout
Authorization Servers
Idx Server Address Port State Tout
Accounting Servers
Idx Server Address Port State Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
Primary ..................................... Local DB
Timer:
Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
EAP-FAST:
Server key ................................
TTL for the PAC ........................... 10
Anonymous provision allowed ............... Yes
Authority ID .............................. 436973636f00000000000000000000
00
Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network Netmask Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11bg :
Channels : 1 1 1 1 1
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address Classification # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID State # APs Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address State # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name State Type Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established -
Multiple Wireless Controller 5508 in WCS 7.0
I have two Wireless Controller 5508 that are IDENTICAL in configurations and they will work as an ACTIVE/STANDBY scenario because right now we only have 30 APs, which one of the controller should be fine dealing with them...
Now, the way we used to work was everytime we had to add a new WLAN, or change an ACL, etc..we had to both controllers and do the exact same things, so both would be ready in case of a failure of the MAIN controller....so in order to avoid this extra work, we bought the WCS 7.0, thinking we would only have to do it once, and the WCS would update both WLC...but I cant find that option..Ive read all the configuration guide, and cant find a way to keep this two controller completaly sync......I read something about templates..but I still have to do "extra" work in order to keep them sync..
How do you guys keep your WLC sync??
THanks!Carlos, make sure you also look at config groups. When you place a template into a config group and if you enable the background task for nightly configuration audits you do get a tally of which controllers are "in sync" and which ones are not. Cisco does not automatically apply any configurations from WCS/NCS to controllers, nor would I ever want them to in all honesty.
NCS is a nice product and has a lot in the roadmap that will hopefully add more value to having your switches loaded. I can see in the future being able to have port templates for voice, data, etc, and then applying those to switch ports at a help desk tech level, they don't need to know how to configure the port, they just need to select a port and then a template. -
Wireless Controller 5508 dropping MAC Addresses
Our 5508 Wireless Controller will drop MAC addresses clean out of the system. Addresses that are in use everyday just disappear. It is not a limitation issue because we are adding iPads everyday. And it is not a daily occurance, but maybe once or twice a week. Has anyone come accross this issue? Everything has been updated and it is more of a hassle than anything, I am just trying to understand what is happening.
Shannon,
can you be a bit more specific, when you say it's dropping mac addresses?
is that from the user list? the macfilter? -
Save config of Wireless Controller 5508 by SNMP
On Catalyst switches one can save the running config with SNMP by using the CISCO-CONFIG-COPY-MIB.
Is there an equivalent way of doing this on a 5508 Wireless Controller ?
Many thanks
chrisIs it Cisco best practices to create one large Vlan that contains both controllers, ap's and clients all in the same network ? Or should I be segmenting the network a particular way?
Not best practice. Segmentation is up to how you want to do it for the most part
With my current Wireless Controllers is it possible to segment the wireless network by building into seperate networks (vlans) but still allow clients to connect to the (mmg_wireless) ssid and roam throughout the campus without mobility and roaming issues?
yes, you could use AP groups and do a subnet per building. the traffic will still backhaul to the WLC then to the core. So if the latency is the fiber between the buildings you would still have an issue. you could also use FlexConnect, but would need to know more on how the application is supposed to work to answer that better
Is it necessary to segment my wireless network by creating more vlans instead of putting all of the ap's controllers and clients all in the same network? Will having all of my wireless devices in the same subnet degrade my wireless network because everything is in the same broadcast domain?
IMHO, I think the AP should be in their own VLAN, and the WLC can live in the 'server' vlan if you want.
Is there a maximum recommended number of ap's that should be on a controller at any given moment? I currently have 200 ap's on one controller.
with 672 clients currently conencted to them. (360 of them are connected to the mmg_wireless ssid) .
how many ports are you using to connect to teh 6509? if you are using all 8 ports you should be fine.
Is it best practice to seperate the maangement ip's of the controllers and ap's from the client vlans?
answered above -
I cannot get my IPad2 to print (it cannot find the printer) using a Laserjet CP1525nw color printer across a wireless network using a Cisco 1508 Wireless Controller with 49 wireless access points. HELP!!!!
What is the secret to getting Bonjour to work on it?
I can get the IPad2 to locate the HP CP1525nw printer without a hitch using a low budget Netgear WAG102 stand alone wireless access point on the same network.If it helps somebody, here is what you need to do.
It worked for me, but only in Multicast-Unicast mode.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0 080bb1d7c.shtml -
Clients are unable to access a New wireless Controller 5508
Clients are unable to access the public ssid, which is wide open(or any other ssids).
I'm using LAG and I can ping each interface on the controller. Ap's show a total of 2 and 2 are up.
interface name is public vlan identifier 107, ip add 10.1.255.252, interface dynamic
Software version 7.0.98.0
Model No.
AIR-CT5508-K9
Burned-in MAC Address
50:3D:E5:1A:2F:60
Maximum number of APs supported
25
FIPS Prerequisite Mode
Disable
UDI :
Product Identifier Description
AIR-CT5508-K9
Version Identifier Description
V01
Serial Number
FCW1508L0KT
Entity Name
Chassis
Entity Description
Cisco Wireless Controller
Profile Name
Type
SSID
Status
Enabled
Security Policies
(Modifications done under security tab will appear after applying the changes.)
Radio Policy
All 802.11a only 802.11a/g only 802.11g only 802.11b/g only
Interface
jmhmanagementpublicspacelabsvoice
Broadcast SSID
Enabled
Layer 2 security none
Below is the errors that are in the controller's log.
spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP 00:00:00:00:00:00 - dropping the join request (# of APs joined = 2)
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-AP_DB_CREATE_ERR: spam_lrad.c:4945 Unable to create an entry for AP 00:00:00:00:00:00 in the database - invalid mac address
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-PAYLOAD_MISSING: spam_lrad.c:5400 Join request does not contain BOARD_DATA payload
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP 00:00:00:00:00:00 - dropping the join request (# of APs joined = 2)
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-AP_DB_CREATE_ERR: spam_lrad.c:4945 Unable to create an entry for AP 00:00:00:00:00:00 in the database - invalid mac address
*spamApTask0: Dec 06 14:54:43.895: %LWAPP-3-PAYLOAD_MISSING: spam_lrad.c:5400 Join request does not contain BOARD_DATA payload
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-DECODE_ERR: spam_lrad.c:1932 Error decoding join request from AP 00:00:00:00:00:00
*spamApTask0: Dec 06 14:54:24.728: %LWAPP-3-JOIN_DB_ERR: spam_lrad.c:6216 Could not allocate an entry in the database for AP
I have attached show run-config and show running-configFor the public WLAN, what is 10.1.1.1? Is it a real DHCP server, is it a FW? If it's a FW, then you'll need to disable dhcp proxy:
CLI config dhcp proxy disable
GUI Controller > Advanced > DHCp, and uncheck the box for proxy.
As for all of your other SSID, they are all pointd at the management interface. Double check the WLAN config, and point them to the interface you want the user to get an IP address in.
HTH,
Steve
Please remember to rate helpful posts or to mark the question as answered so that it can be found later. -
VLAN assignment without ACS on Cisco Wireless Controller 5508
I was wondering if it is possible to do dynamic VLAN assignment on the Cisco Wireless Controller 5508 without using Cisco ACS but use Microsoft NPS server instead? Is there a manual or article that someone can point me in the right direction?
Thank you!Any RADIUS server will allow you to do the dynamic vlan assignment if you configure the right RADIUS attributes (64, 65 and 81 that Steve mentioned above).
This doc shows example of dynamic vlan assignment with WLC and ACS.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Same config on WLC is needed. However, on the RADIUS you need to configure the same attributes on the NPS instead.
HTH
Amjad
Rating useful replies is more useful than saying "Thank you" -
Cisco 5508 Wireless Controller with Splash Page Disclaimer
How do one configure a splash disclaimer page on a Cisco Wireless Controller 5508 with no authentication?
JimmyThere are many options to you in this scenario, but if you're looking to simply provide a splash page via the WLC without interacting with any other web servers, you can configure Local Web Authentication (LWA) as seen in this configuration example.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html?referring_site=RE&pos=1&page=http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/71881-ext-web-auth-wlc.html
If you are not wanting the authentication, you can choose the "passthrough" method which will not require any credentials, only accepting an AUP or whatever you want. -
How to archieve configuration in ciscoworks for 4404 wireless controller
Hi All,
How can we archieve configuration in ciscoworks for 4404 wireless controller.
Thanks in advance.
SamirThe WCS controllers are supported just like any other device. Make sure you have either telnet or SSH enabled for config archive transport, then before a Sync Archive on your controllers. RME will log into them, and run "show running-config" to extract the configuration.
-
anybody know a reseller that would download/sell a firmeware for 2504 wireless controller or what service to buy to be able to get it?
Be aware that you do not need to purchase SmartNET for your APs.
Thanks for the ratings, Marek.
Be aware that nearly all 802.11n APs (some exclusion to AP1250) are covered under the new Cisco Limited Lifetime Warranty. Read through the link provided. This is why I posted that you do not need maintenance contract for the APs. The main thing to understand is that if you need to RMA your AP, it'll take 10-business days for the replacement part to be sent.
I have spoken to some Cisco Authorized Reseller and some Cisco TAC engineers who insist that the Cisco LLW don't exist or doesn't apply to BLAH model. Don't be fooled.
Maybe you are looking for
-
Trying to display an image with eclipse
this is the code: import javax.microedition.lcdui.*; import java.io.IOException; public class DrawImageCanvas extends Canvas{ static Image image; public void paint(Graphics g){ int width = getWidth(); int height = getHeight()
-
How to pass variables to shell script?
I have a shell script which uses the touch command to change the date of a file. To run the command on the command line the syntax is: set-file-date.sh <file> <date> I'm trying to run it from an automator workflow, so I'm prompted for the date, then
-
FINDER: "Get Info" - Window not opening / not working
Hi All, I am kinda lost. Since upgrading to 10.6.4, I no longer can open "Get Info" neither through the context menu not through key [cmd+I]. This is in Finder only. On Application Level (iTunes e.g.) it works. I have checked permissions, they're goo
-
How can i get a new bh-214 ear phones
i want 2 buy ear phones for bh214 bluetooth of nokia xpressmusic series
-
I have cropped a clip and now want to take other footage from the discarded remains of the clip. But the discarded footage is not in my iMovie trash. Where did it go? And how do I rescue it so I can edit the other short clips from it that I need?