Adding Airport Express to working G5 Linksys WRG setup for music...issues

Problem: G5 is "connecting" to wireless linksys network but no longer getting IP address (nor connecting to network to configure AX and itunes doesn't see remote speakers) Using DHCP, can see Mac addresses on Linksys web configure screens.
It worked fine prior to adding AX. I had the G5 connecting to Linksys Network WRG wireless router accesspoint through to DSL modem. This has worked fine for months. Also connect to this network with WinPC. All using WPA Personal security password.
CD Player died, so I purchased the Airport Express to play music to my stereo.
I did get the Airport Express configured...although many tries. I had to turn on broadcast of network name or SID in the Linksys webconfig. Music did play from G5 but I somehow lost the ability to connect to internet. Firefox gave "cannot connect" message. (Safari Network Diagnostics cannot fix issue) When I stopped and restarted the Airport(on G5) the music quit playing. Still have green light on Express. WinPC still works fine as well, HOWEVER:
G5 says that either(depending on which Im trying) that Airport is connected to "wireless network name" but doesn't have ip address OR that ethernet is connected but doesn't have ip address. I see on linksys that the mac addresses are "on". I've restarted everything, I've trashed the sys config folder and restarted G5...still same issue. Again WinPc works fine. Using DHCP...
Any ideas on how to get my G5 back on network? and then I can try to have the AX work again.
No tunes, and now no internet...help?
This is posted on IMAC G5 forum but it was suggested I post here for Express expertise. THANKS.

I would suggest getting your Internet connection back first, and then, adding the AX for streaming iTunes.
Try the following...
Modem/Router Power ReCycling
- Power-off the DSL/Cable modem, Internet Router, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
- Power-on the DSL/Cable modem; Wait at least 30 minutes.
- Power-on the Internet Router; Wait at least 5 minutes.
- Power-on the computer(s)
Typical Linksys Router Setup - Cable
- Access the Linksys web-based setup at 192.168.1.1 (or whatever address your router is set at) using a web browser. The default username is blank & password is "admin."
Setup tab
- LAN IP Address: 192.168.1.1
- Subnet Mask: 255.255.255.0
- WAN Connection Type: Obtain an IP automatically
- Apply (if you make changes)
Status tab
- WAN (all the values here should be populated by your ISP)
DHCP tab
- DHCP Server: Enable
- Starting IP Address: 192.168.1.n, where n should be greater than 1
- Number of DHCP Users: n, where n should reflect the realistic number of concurrent clients that you plan on having connected to the router at any given time.
- Client Lease Time: 0
- DNS 1, 2, 3: <leave at default>
- WINS: <leave at default>
- Apply (if you make changes)
Advanced - Filters tab
- Filtered Private IP Range: <leave at default>
- Filtered Private Port Range: <leave at default>
- Block WAN Request: Enable
- Multicast Pass Through: Enable
- IPSec Pass Through: Enable
- PPTP Pass Through: Enable
- Remote Management: Disable
- Remote Upgrade: Disable
- MTU: Disable
- Filter Internet NAT Redirection: Enable
- Filter IDENT(port 113): Enable
- Apply (if you make changes)
- Leave all the other tabs at their respective default settings.
Connect your G5 directly, using an Ethernet cable, to one of the LAN ports of the Linksys router. Can you access the Internet now?

Similar Messages

AirPort Express not working with Linksys WAG320N

I'm trying to use an AirPort Express to stream music to my home theater speakers.
It's currently plugged in to my router (Linksys WAG320N) via ethernet cable. I can get it to initially play music via AirPlay, but it won't last more than 1 track before it cuts out. It seems to be doing something to the router settings because I then can't see the wireless network via my Macbook Pro or iPhone, and have to change the channel of the router to get it working again.
Are there known compatibility issues between Airport Express and these routers?
Thanks

Any thoughts anyone?

Airtunes/airport express not working with MacBook

I have a new Macbook and an older Powerbook. The Powerbook is working nicely with my airport express and airtunes. I copied all settings to the new Macbook and configured it the same way, I also did the firmware update.
ITunes found the airport express, connected and I could listen to the music.
Later during the day it didn't work anymore, although I didn't change any settings. ITunes can no longer connect to the airport express, the airport utility does find the base station, but I can no longer configure or reset it.
I started the old Powerbook again which is still working without problems
What can I do to get the Macbook working as well ?

Same issue here!! Everything working fine with OS X Tiger. As soon as I upgraded to Leopard the problems detecting the AX started. The setup I have is the following:
-Linksys wireless router
-AX connects to wireless network to play songs through iTunes and to print via USB printer.
The green light on the AX is solid which means that it is connecting to the existing wireless network just fine. The problem lies with Leopard detecting and connecting to the AX. I have tried just about everything over the last few days and nothing seems to work. Some resets and updates let my macbook detect the AX for a little while but then it starts to drop and cannot be detected anymore. Apple HAVE to do something about this. These are two apple products not communicating properly. What ever happened to the good old days of apple products being so user friendly and "plug-and-play"
Disgruntled Mac user

I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

Hello Hornet12,
Indeed, iTunes 10.2 or later will be required to utilize AirPlay.
Using AirPlay
http://support.apple.com/kb/HT4437
AirPlay requirements and capabilities
To get full AirPlay features, make sure your AirPlay-enabled devices are running the latest software updates. The table below identifies minimum AirPlay requirements and capabilities:
Stream content from
Requirement
Notes
iPad
iOS 4.3 or later.1
From the Videos, iPod, Photos, Music, and YouTube apps on iOS devices, stream videos, music, and photos to an Apple TV (2nd and 3rd generation), or stream music to an AirPort Express or compatible third-party device.
With iOS 4.3 and later, you can also stream video and audio from a website or a third-party app installed on your iOS device if the developer for the app or website has added AirPlay functionality.
iPhone (3GS or later)
iPod touch
(2nd generation or later)
Computer
iTunes 10.2 or later.
Stream videos and music from your iTunes library to an Apple TV (2nd and 3rd generation), or music to an AirPort Express or compatible third-party device.
Apple TV
Apple TV software version 5.1 or later.
Stream music from your Apple TV to another Apple TV (2nd and 3rd generation), to an AirPort Express or compatible third-party device.
Cheers,
Allen

Airport Express Stops working when broadcast is turned off

Router: Linksys WRT54G version 2
Using: Airport Express
Purpose of Airport Express: To enable wireless speakers.
After a lot of trouble with the router and eventually having to update all router firmware, changing the type of security the router was working, etc I finally have the router up and running.
Everything is working fine but the last step I'd like to do is not have my SSID broadcast. As soon as I stop broadcasting the network the extreme loses it's connection.
The audio bridge I used before (Sondigo) hasn't updated it's drivers for windows 7 in months so I switched to the airport express but the audio bridge didn't need the SSID to be broadcast to work once it was connected to the wireless network.
Is it possible to have the SSID NOT broadcast and the extreme to continue to extend + broadcast the wireless speakers?
Thanks!

Welcome to the discussion area, Carl M!
You'll enhance your chances of the AirPort Express joining the hidden Linksys network if you "hard reset" the AirPort Express by holding in the reset button until the amber light blinks more quickly, then release.
Configure the Express again to "join" your Linksys wireless network. Since the network will not appear as a choice to join, you'll have to type in the exact name of your network, security and password to give the Express the best chance to connect.
This procedure will sometimes work, sometimes not. Might be worth a try.
Message was edited by: Bob Timmons

HT4587 I downloaded Airport Express Utility 5.6 to get my Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility.

I downloaded and installed Airport Express Utility 5.6 to get my old Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility. What's up?

It is likely that you downloaded AirPort Utility 5.6.1. If you checked the requirements, this only runs on Leopard or Snow Leopard Macs.
You have Lion, so you need AirPort Utility 5.6 for Mac OS X Lion

How do I set Airport Express to work as repeater?

How do I get my Airport Express to work as a repeater for my Apple TV, iPhones and iPad? I use a Mac Pro and a Netgear N300 Wireless N Router. The N300 sees the Airport fine and I can play music to the Airport from iTunes, but none of the other advertised features appear obvious.
All of my other Apple products sync to the N300 Router without issue and apart from some minor setting up to get it working with Apple TV, the N300 presents no compatibilty issues whatsoever.
When I purchased the Airport Express, I truly beleived that the Airport Utility Software, would allow me to choose whether I want to use it for Audio or USB or Repeating / Extending my network, by simply selecting the mode I required, when I required it. After all, isn't that the beauty of Mac computers?
Alas, there is no such drop down menu or button I can press in Airport Utilty to make such a straight forward selection. Instead, from what I can see so far in Airport Utility and various forums, there is a very long and painful process that must be carried out to use the Airport to extend my WIFI network.
I refuse to believe that it can be this hard and assume that that there is some really obvious setting I can change to make this work. It certainly wouldn't surprise me if Apple left this out of the manual, as Apple are legendary for not telling you how connect to 3rd party products, as I found with Apple TV.
As I said, I have read a million threads on this topic and all I have found so far are wanna be geeks, getting lost up there own a**es with lots of technical rubbish that has nothing to do with the problem.
If there is anyone there who actually knows what they are talking about and can explain this without Pythageros Theorem, I would be most grateful.

The AirPort Express can "Join" virtually any wireless network to provide AirTunes and remote printing capability.
But, the "Extend a wireless network" function of the Express appears to be a proprietary feature that will only work with other Apple wireless routers.
As far as we know, this feature is not compatible with routers from any other manufacturers, so there is virtually no chance that it will work with the Netgear N300 router.
I refuse to believe that it can be this hard and assume that that there is some really obvious setting I can change to make this work. It certainly wouldn't surprise me if Apple left this out of the manual,
Well, you can try either the guided setup or the Manual Setup method to configure the Express to "Extend a wireless network", but you are going to get an error message that the "network cannot be extended".
If you have the time and wish to prove this to yourself.....
Open AirPort Utility - Click Manual Setup
Click the Base Station tab below the icons to name the Express, setup a device password and adjust Time Zone settings
Click the Wireless tab and adjust as follows:
Wireless Mode = Extend a wireless network
Wireless Network Name = The name of the Netgear network that you wish to extend
Enter a check mark next to "Allow wireless clients" if not already checked
Wireless Security = Wireless security setting of the Netgear network
Wireless Password = Enter the password of the Netgear network
Confirm Password
Click Update and wait for the error message

Help setting up my airport express to work at a relative's house

I recently upgraded my parents' house from dial-up to broadband connection via local telecom provider (Qwest). With ethernet cable plugged into my MacBook, all is well. But when I plug ethernet cable into my Airport Express unit, I am unable to access Internet. MacBook and Airport Express unit are communicating but -- I'm guessing I need to do something so that Airport Express unit works with a different modem than the one at my residence, i.e. the one now installed at my parents' house. I can probably figure it out if pointed in the right direction. I would be grateful.

It's always a good idea to do a complete power recycle of all the network components when switching networks to allow the modem to recognize the router.
Try the following, in order, checking for Internet access after each step, until resolved:
1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
3. Perform a complete power recycle of your network components as follows:
Modem/Router Power Recycling - Quick
o Power-off the modem, AirPort Express Base Station (AX), & computer(s); Wait at least 5 minutes.
o Power-on the modem; Wait at least 5 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the modem, AX, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the modem; Wait at least 15 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
4. Contact your ISP to have them perform a "modem reset."
You may also want to take advantage of the AX's ability to save multiple configurations.
The AX can store up to five different configuration profiles. You will need to use the AirPort Admin Utility, located in Applications/Utilities to create & save these profiles.
To create a new profile:
o Open AirPort Admin Utility, and select your AX from the list, and then, click Configure.
o Click the Profiles icon in the toolbar.
o Click Add to create a new profile; give it a name, and then, click OK.
o Set options, such as network name, passwords, Internet connection method, etc.
o When done setting the options, click Update.
To switch profiles:
o Open the AirPort Admin Utility, and select your AX from the list, and then, click Configure.
o Click the Profiles icon in the toolbar.
o Click on the desired profile, and then, click OK to apply the new profile and restart the AX.
Just remember to switch to the desired configuration profile before removing power from the AX.

Can't Get Airport Express To Work With ATT's Uverse

For years, AE worked just fine with my 2Wire portal streaming music to my stereo. Went to Uverse 2 months ago, and AE quit working. I am not using an Airport base station, just the Uverse modem and I need help getting it to work.
There is nothing in this forum when I search for uverse, so I post this in hope someone can help me.
I reset AE it and it finally appeared in Airport utility with a yellow light. I click configure and when I choose to join my current network, it sets up it's own Apple network, removing it from Airport utility and changing Airport status in Network to yellow.
No matter what I do or how I try, I just can't get AE to work with the stock 2Wire modem.
Has anyone been able to get AE to work with just the 2wire router & not have to buy an airport base station.
Any help is REALLY appreciated, as I wanna hear my Christmas music, and it's turning me into a Grinch!
Thanks!
Message was edited by: Chris Winkler1

+However, it asks for the security and all I see is WEP in the Home Network set up, I don't know if it's 40 or 128+
AT&T set this up, so only they can tell you for sure. My guess would be WEP 128 since this type of security is stronger than WEP 40.
+And it asks for a wireless password. I entered the one from the router & it did not work. Tried the Key and it did not work.+
This is the same wireless password that you would use if you were logging on to your wireless network with your computer. But, unless you first have the exact, correct security setting for your 2wire router, the password will not work.
+Has anyone out there successfully got their Airport Express to work with Uverse????+
I don't provide instructions to anyone on the forum unless I've first done it myself. I'm providing you with the same instructions that I used to help a neighbor with his 2wire Uverse setup last week. It works fine.
But, he called AT&T to ask them what security setting they used on his 2wire router. Otherwise, we would have had to try each possible setting to see if we could make it work.
AT&T also told him that his password should be 13 characters, all lower case letters with no spaces. That is what the neighbor said he used. I cannot confirm this as he did not share his password with me.
AT&T may have set up the password criteria differently on your router. You need to confirm with them on this.
+What password goes in the Base station tab, Key or Password?+
Any password you want. This is a separate password simply to be able to access the settings on the device in the future when you are using AirPort Utility. You could use your wireless network password if you want.
Please post back on your progress.

I lost my internet last night and now i cannot get my airport express to work

i lost my internet last night and now i cannot get my airport express to work it is blanking yellow on /off

Have you tried AirPort Utility it the Utility folder? If so, what was the result?

I have a MacBook ProDo I have to have the Airport Extreme Base Station for my Airport Express to work?

I cannot get the darn Airport Express to work! It just keeps blinking Amber. I know it must be something silly I am over looking. And I do not have the Airport Extreme Base Station.
Thank you for any help!!!
Elizabeth

Thanks,
This is the rear of your modem/router:
Connect a Cat5e or Cat6 cable from any of the 4 Ethernet Lan ports to the (single) socket on the Express, then go to Airport Utility (Applications>Utilities>Airport Utility) and select create a new network.
You will need to turn the wireless transmiter in the Netgear off, here is a link to the Netgear Manual in case you need to refer to it.
Netgear Manual

Airport express not working with apple products

We have been trying to get airport express to work with a macbook pro, ipad2, iphone, laptop, htc wildfire - havent even tried the air music or printer yet!
We have a green light on the airport express which is connected to an ntl cable modem(virgin media network).
Currently the only thing that will connecy is the laptop and my htc phone. All the apple products will not connect?
We went to the apple store today and it worked grand when it was plugged in - the apple products all worked.
The network comes up on ipad2 but when you press connect it says 'unable to connect'
can anyone help us please?
thank you

I have the same issue. Mine fixed itself for a bit and now it's broken again. I'm thinking it's going to be intermittently broken. I've tried turning both devices off and on again but that did not help.

HT2508 airport Express not working in Mountain Lion

My old airport express stopped working properly since I loaded Mountain Lion. I purchased a new Airport Express and it will work, but the audio fades in and out. I am connected from the airport express unit to my audio receiver via a 3.5 out into RCA (red/white) connector into the receiver. Can someone suggest a cure?

I have three printers up and running connected to an Air Port Express,
and since I upgraded to Lion I can't connect to any of them, so I continued using SL on this MBP17.
System Preferences does not show any of my printers.
I opened Air Port and it says I need to update.
When I click on the update button, it takes me to the App Store, but no Air Port Software — What gives?
Now having the same problems with Mountain Lion.
Hoped ML would fix the problem, but NO.
I find I have to save documents to a flash drive and go to my old PowerMac G4 to print.
Steve we miss you. Apple is going to crap without you.
Message was edited by: random47 to fix typos and add information.

Airport Express Not Working

Maybe someone can give me a hand. The airport express is working great for AirTunes but will not hookup to the internet. We've plugged in via ethernet wire and it works fine. We've also tried resetting the airport and unplugging it, resetting our computer. No dice. On the top of the computer screen the aiport indicator reads full internet perfectly but cannot connect. We're stumped.
Thanks for anyone who can give us a hand.

Assuming you have a green light and you wireless mac can see the network but you have no internet; unplug the cablemodem for a minute.

Airport express not working since today's itunes update

Since updating iTunes today, Airport Express not working. More specifically, the Airport software will recognise the device exists, but iTunes cannot connect to it, just getting error message.

Ray Dio wrote:
Since updating iTunes today, Airport Express not working.
try this:
go system preferences > network > airport > advanced > TCP/IP and set *configure IPv6* to off. click on apply.
now have iTunes connect to the remote speaker again.
JGG

Adding Airport Express to working G5 Linksys WRG setup for music...issues

Similar Messages

Maybe you are looking for