Adding Hard Drive and FCP
I have a G5 with 10.3.9 OS, and FCP HD, I just recently started to use it and learn the program. But I have filled up my hard drive. I purchased a OWC Mercury external hard drive, 200 GB, added a FW 800 adapter port, and installed a 500GB seagate internal hard drive. When clearing off my original hard drive, do I just copy all files to the other drives and delete from my original or will I lose data important to FCP?
Welcome to the forum!
When you say; "... I have filled up my hard drive," do you mean your boot drive?
You should maintain at least 10% free space on ALL drives, especially your boot drive. If you plan on keeping the original boot drive, keep your applications and project files there. Move any captured or imported media, renders, etc. that FCP uses for your projects to the second internal drive. Next time you launch FCP, reset the capture/scratch disc to the new internal drive so any future captures and renders will go there. If you do move the media, you'll have to reconnect the various files when you open an on-going project.
Alternatively, you could use Media Manager to move the need files. But since Media Manager isn't always reliable, I'd go with the first method. You might as well trash any render files and just re-render when needed.
-DH
Similar Messages
-
I got lots of short questions and a semi bigger one.
I plan on editing HD and standard definition video with my iMac using FCP. My hard drive is 130 gig and I need a bigger one. My current fire wire ports on my iMac are both 400mb/sec and that is too slow for HD and I was told I cannot get that upgraded. The guy at an apple store told me iMac's use lap top hard drives and there is no big improvement from my current 130 gig.
I looked my hard drive up and I believe it is actually a desktop hard drive if I'm not mistaken. The model number is ST3160812AS. So does that mean I can get a desk top hard drive upgrade? If so I was looking at the Hitachi Deskstar 7K1000 750g 7200 rpm. Is that a good choice?
How do you upgrade to a new hard drive anyway? Who installs it? Me or can I get a professional to do it for me for a small fee? How do I get all the current data on my hard drive on to the new one?
Where I usually do most of my editing the computers have two hard drives. One to hold the footage and transfer the data to the other one which is actually doing the editing. My film teacher says this is the best thing to do, but obviously I can't do that since two hard drives in my iMac is out of the question and I can't get a fire wire port fast enough to support a hard drive that isn't just for storage. Can that hard drive I was looking at handle doing the two processes on its own? Do I have any other options?
Thanks in advanced.J D McIninch wrote:
\- The bitrate for HDV high-definition video is *25 Mbps* -- 1/16th the bandwidth of FW400.
\- Max bitrate for AVCHD is *24 Mbps*.
\- DVCPRO100 has the highest bitrate of all the HD video formats at a whopping *100 Mbps*.
The maximum burst speed of FW400 is about 393 MBps \[typo: 393 Mbps\] and sustained
transfer rate it near that.
You shouldn't worry about the transfer rates on FireWire as much as the drives.
Most hard drives are not going to be able to sustain transfer rates of 100 Mbps --
you probably need an array for that. It's moot, however, if you are using consumer-grade
HD (with rates around 25 Mbps).
Very useful info on the video data rates on various formats, JDM -- thanks.
However, I'm a little confused by the disk drive data rates you quoted. It appears that
the numbers you mentioned are actually MBytes/s (MBps) rather than Mbits/s (Mbps).
The OP's current internal HD (ST3160812AS) is a 160GB Seagate 7200.9 family drive
spec'd at 83MBytes/s max sustained throughput. (That applies only to the outermost
tracks, when the drive is nearly empty. It'll be about 40MBytes/s on the inner tracks.
So, when nearly full, the internal drive is about the same speed as a FW400 external.
The 750GB Hitachi Deskstar 7K1000 is slightly faster (ca. 85-90MBytes/s maximum,
when empty, and half of that when nearly full). That's fairly fast as today's large HDs
go, but not quite as fast as the new Seagate 7200.11 family drives (105MBytes/s max)
or WesternDigital's WD7500AAKS (98MBytes/s, max) -- but they're all more than fast
enough to saturate a FW400 link, even when the external drive is nearly full.
BTW, from the spec sheets, I see no indication that any of the four drives mentioned
here are "green." They all have similar power requirements; if anything, the Hitachi
consumes the most power, and the Western Digital the least. (That seems to agree
with tomshardware.com's observation 7K1000 drives run hotter than most others.)
It is nice to see that today's fastest 750GB drives consume no more power than the
best-performing 160GB drives of a few years ago.
vtwiz wrote:
Don't attempt to replace the drive in your iMac. Keept it for the OS and software
and use an external drive for all your video.
Good advice! Regardless of the size of your internal drive, save the data-flogging
for the easily-replaceable external drive.
Looby -
Power Mac G4 Won't Boot after Installing 2nd Hard Drive and Additional RAM
Hello. I am using a Power Mac G4 (PCI graphics) that I bought a few weeks ago. It was working perfectly fine until I tried to add an additional hard drive and add more RAM to the machine. After I closed the case and plugged it back in, it won't start up at all. No sound, no lights, nothing spinning, nothing. I removed the added hard drive and RAM, but it still refuses to start. I don't know what happened. Hopefully it's not a logic board failure or anything else equally bad.
Welcome to Apple Discussions!
The PowerMac G4 PCI forum is over here:
http://discussions.apple.com/forum.jspa?forumID=586
I'll ask a moderator to move your thread. Try replacing the clock battery, and hitting the CUDAS switch. -
hello,
if i back up my itunes library to an external hard drive and then add subsequent music and want to back up the newly added music a few days later, can i do it without backing up the entire library again? or do i need to back up the entire library each and every time i back up to the external hard drive?Just copy Users/yourusername/Music/iTunes (containing your library-files) to your external drive as well as that (extaernal) folder that contains all your audio-tracks.
-
FCP 7.0.3, Canon XF100, saved some clips to a portable hard drive and now they won't import? Tried moving them back to the CompactFlash but still won't import? iMac, 10.6.8
Well, for FCP to see this file structure and recognize it, you need to download the Canon XF Log and Transfer plugin...
http://software.canon-europe.com/software/0040354.asp?model=
>I don't have the original clips on the card.
Meaning that they didn't back up the full card structure? Lordy...very few shooters do this and it is maddening. If you don't have the full card structure, even with the plugin, FCP cannot log and transfer.
As for ClipWrap2...that should work. Do you have the right files? -
I moved my FCP events and projects folder onto my external hard drive and now everything is gone on FCP. When I tried to reload those folders onto FCP nothing happened. I still get the missing files image. When I try to import the folders manually something pops up that says it is incompatable. It is possible to retrieve everything that was lost?
"When I tried to reload those folders onto FCP nothing happened"
Brownale6 how can u reload folder in to FCP.
As you said folders are moved to external disk but have you checked it should be like this
For Event
external disk>Final Cut Events>your event folder.
For project
external disk>Final Cut Projects>your project folder. -
How to move iTunes Library/Media Files to external firewire Hard Drive and make it the master library, and then point iTunes to that when adding new content??
Copy your ENTIRE iTunes FOLDER to an External Drive...
Full Details Here > http://support.apple.com/kb/HT1751
To Operate iTunes from the External Drive...
Start iTunes with the Option key held down and guide it to the new location of the library.
Be Sure the drive is Formatted Mac OS Extended (journaled)
Also... have a look at these 2 Videos...
http://macmost.com/moving-your-itunes-library.html
http://macmost.com/moving-your-itunes-media-to-an-external-drive.html -
every time after I have upgraded my macbook pro I am unable to upgrade to mountion lion , it aways will either go blank and I have to start fresh from cd system going all the way till I get to last upgrade and then loss everything. any help or what is happening
<Edited by Host>you are correct, I have had my mac at geek squad to correct this problem and they could not find the fix other thanit was a hard drive problem and they replaced the hard drive and that did not fix the problem, they said it could be the speed of the HD I used as a replacement ,which was 7200,o the nw one is 5800 yet I still or they could not upgrade . they were used a jump drive and they tried to down load from itunes no luck. I started out wth the install disk and stepped up ,what could be wrong?
Preferences
1
2
3
4
5
6
7
8
9
0
=
Backspace
Tab
q
w
e
r
t
y
u
i
o
p
Return
capslock
a
s
d
f
g
h
j
k
l
shift
`
z
x
c
v
b
n
m
shift
English
alt
alt
Preferences -
Playlists Missing After Install New Hard Drive and Upgrade to Win 7
My computer needed a new hard drive and I upgraded from Win Vista Home Premium to Windows 7 Home Premium.
I am trying to get my Playlists back for my iTunes in my "Administrator" user account, after reinstalling iTunes and putting my music libraries back onto my computer.
(I had installed 32-bit Win7 OS myself, computer worked OK for about 1 day, then would not boot up; I took computer to shop, they said I needed new Hard Drive, and I gave them my new Win7 OS computer disks)
I am confused over whether I have 32-bit OS or 64-bit OS. They recommended installing 32-bit OS, I agreed, and believed that I had 32-bit OS installed; however, Computer / System Properties state "System type: 64-bit Operating System"
Prior to my installing Win7, I backed up the following onto my Western Digital "My Passport Essential Portable Hard Drive:"
("My Administrative Account"): Users / Owner / My Music
and
("My User Account"): Users / Yank / My Music
My "Administrative" and "User" user accounts contain different songs in iTunes.
If helpful, I could describe what is in each of these 2 backed-up music folders.
To get started, I copied both my "Owner" and "Yank" user folders in the C: User folder; however now I have "Owner," "Yank," and "Yank.Owner-Toshiba" folders in the C: User folder. I think I did this by creating a new Yank user account by creating a new account, not by my copying a folder into C: User folder. The Owner folder has a picture of a lock on the folder icon.
Because I had trouble merging My Music folders in the Owner folder, and I was confused, I copied everything that was in the Owner folder into a new folder in the Owner folder, "NEW OWNER FOLDER." I also copied my Owner Music folder into several places in my Users / Owner folder.
I also ended up changing the "iTunes Media folder location" several times, using iTunes "Edit / Preferences / Advanced tab / change "iTunes Media folder location". When I chose "Reset," it shows "C:\Users\Owner\NEW OWNER FOLDER\Music\iTunes\iTunes Media"
I've also played around with "Edit / Preferences / Advanced tab / 'Keep iTunes Media folder organized' "
When I open my iTunes, I have no playlists.
However, when I went to my "Yank" user account and opened iTunes for the first time, the playlists associated with that account were visible.
How do I get my playlists back on my Administrative Account, which is my main song collection and had many, many playlists?
Thank you.YAY!
I didn't try shift-start of iTunes, but I DID GET MY PLAYLISTS BACK BY FOLLOWING YOUR OTHER ADVICE:
I went to my external hard drive, went to my backup at Users / Owner / My Music / iTunes / and searched for library.itl
Four files with that name were found, with different dates.
I chose the most recent, dated just a few days before I made my backup to the external hard drive.
I copied it to my computer's hard drive into the following location:
C:\Users\Owner\NEW OWNER FOLDER\Music\iTunes
which overwrote the file which was located there.
When I opened iTunes, ALL MY WONDERFUL PLAYLISTS WERE THERE!
THANK YOU SO MUCH FOR SOLVING THIS FOR ME!
CAN YOU IMAGINE HOW DISAPPOINTED I FELT WHEN I BELIEVED THAT I HAD LOST ALL OF THE PLAYLISTS WHICH I HAD CREATED OVER THE YEARS? Many of my playlists were composed of whole albums whose songs I had added to iTunes.
THANK YOU AGAIN SO MUCH! -
Greetings everyone
as the title says, ive had to install a new hard drive and i want to transfer my old itunes library onto the new drive, maintaining all playlists/play counts/ratings etc, album artwork if possible. The old hard drive is installed as a slave drive and is completely acessible, but due to the boot files being corrupted i cannot use it as the main drive and therefore operate my old itunes. Also, my ipod no longer contains my music library as itunes synced without my permission and wiped it.
The only thing i have tried is copying all of my old music files from the old drive by selecting 'add folder to library' and then the old drive, then replacing the new itunes library.itl file with the one from my old itunes. This restores all my playlists and playcounts but when i try to play any of the songs it says that the files could not be found, and i dont fancy locating 8500 music files individually!
Thankyou for taking the time to read my post, any help will be greatly appreciated.Ah, my reply was based on the assumption that you had a default installation of iTunes.
i.e you had all your music in the iTunes media folder inside your iTunes folder.
If your iTunes folder is so small compared to the amount of music you have, you must have a different arrangement.
This complicates you situation considerably.
iTunes can cope with moving around as long as all the music is in the iTunes media folder, not not if it isn't.
Your first step should be to get iTunes working on the old drive. This will involve editing the xml library file so that the drive letter is correct and then rebuilding the library from the xml file.
Then you will need to consolidate your library which moves everything into the iTunes media fodler. After that you will be able to use my first suggestion.
Step 1
Find the iTunes folder on the old drive and copy the two library files somewhere else so you can find them again. That's iTunes Library.itl and iTunes Library.xml.
Now open the copy of iTunes Library.xml with WordPad.
Look for lines starting:
Location
These contain the paths to tracks.
You will need to use a find/replace to change the drive letter so that it is correct.
Make sure that you include enough in the "find" so that you only change the right thing.
Maybe /c:/ and replace with /d:/ or whatever.
After that, tell iTunes to use the library on the old drive with a shift key start.
Hold down the shift key and start iTunes, keep holding the shift key until you are prompted to choose a library. Navigate to the iTunes folder on the old drive and choose iTunes Library.itl.
Then use the method in the following article to rebuild your library;
http://support.apple.com/kb/HT1451
Unfortunately the date added will be today for all tracks.
If iTunes works correctly after this, consolidate your library
File>>Library>>Organize>>consolidate
This copies all tracks into to iTunes media folder and could create a problem if you do not have disk space so don't do it if you are unsure about free disk space.
Check that iTunes works OK and then use the first method.
Message was edited by: polydorus -
My old PC crashed and I ended up buying a new one. I was able to recover all my music from the old hard drive and restore it in itunes. I purchased a new album online thru itunes and added it to my library. When I tried to add the album to my 6th nano it wouldn't download. All the tracks are check marked and I can listen to the album on my pc but it won't sync onto the ipod. The new pc is authorized, any ideas?
You can only sysc with one iTunes library. The new computer is a new library. You have to restore your iPod on the new conputer and then sync.
-
Moving Content to External Hard Drive and Using New Computers
Before doing this, I want to make sure I know how to do all of it:
We are going to buy two new laptops, and retire the old one. I want to move all of my iTunes content from the old laptop to an external hard drive attached to an Airport Extreme. I then want to be able to share the content between the two computers. I know how to do this, and plan to move the library data base files to the external hard drive, as well.
However, I also want to be able to continue synching all of the content to the Apple TV. To what should the Apple TV be synched after the content is moved to the external hard-drive and the old computer is replaced by two new computers? How is that done under the circumstances? And, in the meantime, will the Apple TV lose all of its content and need to be re-synched entirely from scratch, or will it continue recognizing the current iTunes library as moved to the external hard drive?
Thanks!This is an option, although as a note of caution; depending on how regularly you modify your library this could become a little bit of a chore. The option is likely a good one in many cases but not all.
In my own case I considered using an old mac as my media server in the sense mentioned by tmartine. (I do a bit of experimental stuff and need to restart my mac quite often, I also have 5 Apple tv's and a library which is too large to do anything but stream, my family don't take too kindly to my frequent restarts and I find myself waiting until the early hours).
However I also modify my itunes library on a daily basis, I buy quite a bit of stuff and also add my own movies regularly, as well as make several recordings a day through my eyetv, all this new content would need to be manually added to my (server) library (and deleted manually), I felt this would be too many extra things for me to do and so my personal preference is to have my itunes library on my main computer as the primary library. -
Help I just moved my music files to a external hard drive and am using the new crappy version ( i know my opinion) of itunes and cant add the files to my libray it gives me the add file to library option but not the add folder to library option what am i doing wrong?
In iTunes 11 uncheck the preferences setting in in the iTunes Preferences panel "Advanced > Copy Files to iTunes Media folder when adding to Library"
-
I have about 130 gigs of movies on my iTunes and was wondering if I can just put them on my backup hard drive and remove them from my main computer to free up the space.
I haven't done this with an external drive, but I would imagine it works the same way as if you have multiple internal drives. Also hopefully it works with less headache in OSX than in windows.
Anyway, move all your music over to your external, and then go into itunes -> preferences -> advanced -> iTunes media folder location. Navigate to your drive, and pick the folder you want. Ensure that your folders are set up like they are in your ~/Music/iTunes folder, or wherever your iTunes is currently pointing. Then quit and restart itunes. If your music doesn't show up, try dragging your music folder from your external onto itunes, and it will hopefully update your library.xml.
As far as Jerry's problem goes, you could try adding another music folder to your library.xml, but I really have no idea whether this will work or not. If you want to give it a try (can't promise you won't corrupt your library.xml, so make a copy beforehand) you can find the music folder xml element right near the top of the xml file (open it with textedit/textmate/whatever text editor you want (NOT WORD)). Curious to know if this works, and if it doesn't I have other ideas so let me know. -
I moved my itunes library to an external hard drive and then I tried to sync my ipad. I got a message that says my ipad is synced to another library and it will erase my ipad, which I don't want to do. I'm not sure how to fix this problem, any ideas?
Ok. progress...
So is your media folder called iTunes Music or iTunes Media? And does it have a folder called Music inside it?
Before going any further you should first attempt to use File > Library > Organize Library > Rearrange files in the folder "<Media Folder>" (ignore if grayed out). This will make sure that any iPod Games or Mobile Applications get placed inside the iTunes Media folder which is needed for portability.
If your iTunes Media folder is called iTunes Music, close iTunes, rename the folder as iTunes Media and start iTunes again. iTunes will automatically adjust. Close iTunes again.
On your external drive rearrange the folders that you have already copied there so that they match the layout in your active library. You should end up with a folder called X:\iTunes where X: is the external drive letter, and the media folder is X:\iTunes\iTunes Media. If the library layout was upgraded then you will need to create a Music folder inside this and move all the artist folders and Compilations into Music. You will also need to copy iPod Games and Mobile Applications from your internal drive into the new media folder. Next copy the files iTunes Library.itl, iTunes Library Extras.itdb, iTunes Library Genius.itdb, sentinel and the folder Album Artwork from the internal drive into X:\iTunes. The preceding manipulations should make the internal and external copies of your library match without you having to copy all of the media over again.
Now hold shift as you start iTunes. Click choose, browse to and open X:\iTunes\iTunes Library.itl.
Finally use File > Library > Organize Library > Consolidate files. This will ensure that any stray files that might have been added from outside your original media folder will be copied into the new one.
You can now reclaim the space used by your library on the internal drive, however before you do so I would advise you to obtain another external drive and make use of this backup tip.
tt2
Maybe you are looking for
-
Microsoft Clip Gallery quit unexpectedly
I know this seems like more of a Microsoft problem than a Mac problem, but no one on the Microsoft for Mac forums seems to have a clue. So I thought I'd check here. I have a 15" MacBook Pro (Intel) running OS 10.5.6. I have had Office 2008 installed
-
Can a canon pixma MG6120 be used wirelessly with an ipad 3
Apologies if this is a naive question, but I'm totally new to the iPad / Apple environment & am having a hard time finding out a) if my new iPad 3 (Wi-Fi & 3G) will connect with My Canon Pixma MG6120 printer that is set up with my PC desktop computer
-
Image Capture-Where is the take picture button?
Hey everyone. I was going to try out the "Take Picture" feature in Image Capture, but for some reason, the button is not there. Nor is it under the customize buttons option. Does it only let you put it there if you are using a supported camera? Thank
-
I have an iPhoto Library of some 20000 photos. When Migrating to Aperture, it seems that the recommendation is to use multiple libraries. I have already loaded the entire iPhoto library and given the differences in the look at feel between the two ap
-
SLD change for Portal 7.0 system
Hi Experts, Need to change existing SLD for the time being in Portal system 7.0 which has totally 5 server nodes In the visual admin, should I have to mention the new SLD entries in SLD data supplier for one server node ( cluster > server node 1 > se