Adding polycom soundstation ip 7000 to cme 4.1...is it possible?

Hi
Please can anyone advise if its possible to add polycom soundstation IP 7000 to CME 4.1?

Hi Brandon.
No you don't need to specify Owner because the digest user field is used to authenticate the phone against the CUCM. (That is defined as authorisation user on third party phone)
Zach,
the password field on Polycom is the password field on end user configuration (not pin not digest password.
Does the callmanager report rejected on phone status?
Let me know
Regards
Carlo

Similar Messages

Polycom Soundstation IP 7000 Registration Issues

Hello All,
I've posted this before, and thought I had it resolved, but I'm back to pulling my hair out at trying to get a Soundstation IP 7000 to register with my call manager.
Here are the cliff notes:
-CUCM Version 8.6
-Polycom Firmware 4.0.4 (the highest revision mentioned in their guide for CUCM)
-The polycom can ping the CUCM Sub and Pub
-There is no syslog message on the CUCM of the Polycom trying to register
I've attached screen shots of everything that I believe to be relevant, if anyone out there has an idea of what might be going I would greatly appreciate the input. I have not yet resorted to traffic analysis with WireShark. I've got some notes on the images of the Polycom screens.

Hi Brandon.
No you don't need to specify Owner because the digest user field is used to authenticate the phone against the CUCM. (That is defined as authorisation user on third party phone)
Zach,
the password field on Polycom is the password field on end user configuration (not pin not digest password.
Does the callmanager report rejected on phone status?
Let me know
Regards
Carlo

Installing an analog polycom soundstation 2 on FXS port in CUCME

I apologize if this is a stupid question, I'm an Avaya voice (cisco data) guy, I'm still learning Cisco voice.
I've installed an analog polycom soundstation 2, I can make internal and external calls. However I can only receive one incoming call at at time (second call receives a busy signal) and I can't conference a second call.
From researching I think I need to change the FXS port from MGCP to SCCP (I have the license for it) but I'm not 100% sure that's correct and if it is I'm not sure how to do it.
Any advice would be much appreciated.

This should give you an idea where to start
http://www.icciev.com/1/post/2011/09/adding-vg224-to-cucm-80-as-sccp-or-mgcp-gateway-differences-and-configurations-part-2.html
Jorge Armijo
Please remember to rate helpful responses and identify helpful or correct answers.

Adding Polycom HDX8000 to TMS with security mode

I have been adding Polycom HDX8000 to Cisco TMS but doing so i had to disable security mode on HDX8000 which enables SNMP (SNMP needs to be enabled on HDX8000 to get identified during adding process in TMS)
I am able to add HDX8000 to TMS but in doing so the HDX is now being accessed using http since security mode is disabled.As per the security norms all HDX's needs to have secured web access (https), if i enable security mode on HDX then SNMP is disabled resulting in TMS loosing control over HDX (error on TMS:"no snmp response")
Basically i want to enable SNMP at the same time have https only access to HDX8000
Has anybody else encountered the above mentioned situation ?
TMS 14.4.0
hdx8000- 2.5.1 - 3.1.6

In order for TMS to control the Polycom HDX, you'll need to disable Secure Mode. How to setup TMS and the HDX to work together, see the TMS Product Support Guide, it's outdated being it was for TMS 13.x, but it's still valid when it refers to the HDX and what needs to be configured. It mentions about disabling Secure Mode, and using a security profile of medium or below. Just from looking at the Polycom HDX Admin Guide, on pg 311 at the medium security profile details, it looks like you could tweak the security profile when secure mode is disabled and maybe change the web port to 443 instead of 80, though this is just a guess and untested.

Polycom Soundstation SIP or XTML

I have a Polycom Soundstation Duo which I'd like to use as the speaker and microphone when placing Skype calls. The "connector" cable offered by Polycom to connect to "PCs" is not compatible with a Mac. (There is no microphone port on an AirBook).
Are there other options? Can the Skype software take advantage of the SIP or XTML over ethernet to utilize the Polycom equipment as both the speaker and microphone? Am I missing some other possible solution?
Thank you for any advice or suggestions.

Correction it doesnt look like the phone is registered. Hrm....

In have added text to my photos on my mac. Is it possible to transfer that text to the same photos on my iPad which I then display on my TV using Apple TV.

I have added text to my photos on my iMac. Is it possible to transfer this text to my iPad so that I can view the photos with text on my TV using Apple TV.

How did you add the text to the photo in the first place?
OT

Any way to use Polycom SoundStation IP 6000 or IP5000

can I somehow connect one of those stations to my UC 320?
Thank you

Paul,
Please look at the FXS connected conference phones. Only the Cisco SPA phone series are supported on the UC320W.
The SPA512G & SPA514G were added in 2.3.1(14) Release Candidate firmware.
Randy

Adding connection to TDM network in CME

I have a Cisco 2651 with CME and I want route internal traffic to the PSTN network.
I don't have PSTN cards.
I only have 3 ethernet cards.
I want to configure accounts of my SIP provider to do calls to the PSTN or route all the calls to an external gateway.
How can I do it ?

You need to have an FXO port or a T1/E1 card to route the calls to PSTN

Upgrading to iPhone and adding old phone back onto plan later... is it possible?

I am on the verge of upgrading my non-smart-LG Octane to an iPhone. Currently my husband has a very very cheap Tracfone, which is fine for him as he rarely uses it- we don't have a land line so it's basically an emergency phone. However, Tracfone is not that great and his cheap phone is falling apart. My current Verizon plan is just for one phone, with no data plan. If I upgrade to an iPhone now, can I hang onto my Octane and add it back to my current plan as his phone later on if he decides he would rather do that than keep the Tracfone? Last time I upgraded I was able to let him have my old phone and use it as the second phone on the Verizon plan, but I want to be sure I can do it later on instead of having to decide when I get the iPhone. I'm trying to keep my costs down as much as possible, and he won't be needing a data plan (I don't have one currently) so I want to wait until know for certain what the iPhone will cost monthly before deciding if it's a good idea to add another Verizon line and give up the very cheap Tracfone line. Thanks for any help you can give!

edna_million wrote:
... If I upgrade to an iPhone now, can I hang onto my Octane and add it back to my current plan as his phone later on if he decides he would rather do that than keep the Tracfone? Last time I upgraded I was able to let him have my old phone and use it as the second phone on the Verizon plan, but I want to be sure I can do it later on instead of having to decide when I get the iPhone.
Yes, you can upgrade now, add the data plan for the iPhone ($30 for 2 GB data), and then later add a second line using the Octane. At that point you MAY have to switch to the Share Everything, since you are on an individual (I'm assuming) Nationwide plan with limited minutes; the option to add a line and make it shared plan may convert it to SHare Everything (unlimited minutes and texting, shared data).
In either case, you don't need to decide when you upgrade to the iPhone. The options will be similar now or later.

Adding user to the oracle database using database link - is it possible?

Hi, i wolud like to manage my databases using one client. I easilly operate on my distriubuted tables but i have problem with creating users in distribiuted database. Is it possible to create users in distributed database using database links? or it have to be done locally using some stored procedures or sth similar?

The SQL syntax of the CREATE USER statement doesn't support DB links, the only way to do it would be with stored procedures. There might be an Oracle SP for that or for generic remote execution of SQL, but I'm not familiar with such.

Issue with LPCOR on CME 10.5

Dear All,
I am facing issues with LPCOR configuration on CME 10.5. For International calls the Authentication Prompts triggers some times and some times doen not.
Also when a local call is dialed the Authentication Prompt is triggered some times.Below is the config and debug logs. Need your help to resolve this.
voice lpcor enable
voice lpcor custom
group 10 endusers
group 11 pstn
voice lpcor policy endusers
service fac
accept endusers fac
accept pstn fac
voice lpcor policy pstn
service fac
accept endusers fac
accept pstn fac
application
package auth
param passwd-prompt flash:enter_pin.au
param max-retries 0
param abort-digit *
param term-digit #
param user-prompt flash:enter_account.au
param passwd 12345
param max-digits 32
interface GigabitEthernet0/1.1
encapsulation dot1Q 1 native
ip address 10.25.76.1 255.255.255.0
interface GigabitEthernet0/1.201
encapsulation dot1Q 201
ip address 10.25.77.1 255.255.255.0
voice-port 0/0/0
lpcor outgoing pstn
trunk-group ALL_FXO 1
supervisory disconnect dualtone mid-call
supervisory custom-cptone 2n-gsm
no battery-reversal
input gain -6
output attenuation -3
cptone SA
timeouts call-disconnect 1
timeouts wait-release 1
timing sup-disconnect 50
connection plar 5040
caller-id enable
cable-detect
dial-peer cor custom
name local
name longdistance
name 911
name Internal
name fac-int
name user-fac
dial-peer cor list local
member local
dial-peer cor list call-local
member local
dial-peer cor list call-longdistance
member longdistance
dial-peer cor list user1
member local
member 911
dial-peer cor list user2
member local
member longdistance
member 911
member user-fac
dial-peer cor list user3
member 911
dial-peer cor list call-911
member 911
dial-peer cor list call-internal
member Internal
dial-peer cor list fac-int
member local
member 911
member fac-int
dial-peer cor list user-fac
member user-fac
dial-peer voice 96 pots
trunkgroup ALL_FXO
corlist outgoing call-911
destination-pattern 9[2-6]......
forward-digits 7
dial-peer voice 901 pots
trunkgroup ALL_FXO
corlist outgoing call-911
destination-pattern 901[2-4,6-8].......
forward-digits 10
dial-peer voice 800 pots
trunkgroup ALL_FXO
destination-pattern 9800T
prefix 800
dial-peer voice 900 pots
destination-pattern 9T
port 0/0/3
prefix 9
dial-peer voice 11 pots
destination-pattern 901........
port 0/0/3
forward-digits 10
dial-peer voice 9051 pots
trunkgroup ALL_FXO
corlist outgoing call-local
destination-pattern 905........
forward-digits 10
dial-peer voice 19 pots
trunkgroup ALL_FXO
corlist outgoing fac-int
destination-pattern 900T
translate-outgoing called 1
forward-digits all
dial-peer voice 20 voip
description International calling
service clid_authen_collect
destination-pattern 900T
lpcor outgoing pstn
session target ipv4:10.25.76.1
incoming called-number 9T
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
ephone-dn 1
number 4121
name John
corlist incoming fac-int
ephone 1
lpcor type local
lpcor incoming endusers
mac-address E0D1.730A.21DE
ephone-template 2
type 7942
button 1:1
voice register dn 33
number 4163
call-forward b2bua busy 5000
call-forward b2bua noan 5000 timeout 20
call-forward b2bua unregistered 5000
allow watch
name Joseph
mwi
voice register pool 33
busy-trigger-per-button 4
id mac BC67.1C31.C8AA
type 7821
number 1 dn 33
cor incoming fac-int 1 4163
dtmf-relay rtp-nte
codec g711ulaw
transfer max-length 4
Debug Logs
DAMAC-CME-ANOUD#DEBUg VOIce lpcor all
voip lpcor all debugging is on
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#term
DAMAC-CME-ANOUD#terminal i
DAMAC-CME-ANOUD#terminal i
Apr 12 16:22:39.825: %VOIPAAA-5-VOIP_CALL_HISTORY: CallLegType 1, ConnectionId F692C420E06611E4BB0CE7FDC5486EA5, SetupTime 16:22:35.615 UTC Sun Apr 12 2015, PeerAddress 4130, PeerSubAddress , DisconnectCause 10 , DisconnectText normal call clearing (16), ConnectTime 16:22:39.825 UTC Sun Apr 12 2015, DisconnectTime 16:22:39.825 UTC Sun Apr 12 2015, CallOrigin 2, ChargedUnits 0, InfoType 2, TransmitPackets 0, TransmitBytes 0, ReceivePackets 0, ReceiveBytes 0
Apr 12 16:22:39.825: %VOIPAAA-5-VOIP_FEAT_HISTORY: FEAT_VSA=fn:TWC,ft:04/12/2015 16:22:35.609,cgn:4130,cdn:,frs:0,fid:2599,fcid:F692C420E06611E4BB0CE7FDC5486EA5,legID:284C,bguid:F692C420E06611E4BB0CE7FDC5486EA5mon
DAMAC-CME-ANOUD#terminal imon
                          ^
% Invalid input detected at '^' marker.
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
Apr 12 16:22:44.089: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_name:
   lpcor endusers
Apr 12 16:22:44.089: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_name:
   lpcor endusers index 10
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#show debug
VOIP LPCOR:
debug voip lpcor error call is ON (filter is OFF)
debug voip lpcor error call informational is ON (filter is OFF)
debug voip lpcor error software is ON
debug voip lpcor error software informational is ON
debug voip lpcor detail is ON (filter is OFF)
debug voip lpcor function is ON (filter is OFF)
debug voip lpcor inout is ON (filter is OFF)
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
Apr 12 16:23:22.889: %VOIPAAA-5-VOIP_CALL_HISTORY: CallLegType 1, ConnectionId FBA1532AE06611E4BB10E7FDC5486EA5, SetupTime 16:22:44.089 UTC Sun Apr 12 2015, PeerAddress 4130, PeerSubAddress , DisconnectCause 10 , DisconnectText normal call clearing (16), ConnectTime 16:23:02.009 UTC Sun Apr 12 2015, DisconnectTime 16:23:22.889 UTC Sun Apr 12 2015, CallOrigin 2, ChargedUnits 0, InfoType 2, TransmitPackets 0, TransmitBytes 0, ReceivePackets 1038, ReceiveBytes 166080
Apr 12 16:23:22.889: %VOIPAAA-5-VOIP_FEAT_HISTORY: FEAT_VSA=fn:TWC,ft:04/12/2015 16:22:44.093,cgn:4130,cdn:,frs:0,fid:2600,fcid:FBA1532AE06611E4BB10E7FDC5486EA5,legID:284D,bguid:FBA1532AE06611E4BB10E7FDC5486EA5
Apr 12 16:23:22.905: %VOIPAAA-5-VOIP_CALL_HISTORY: CallLegType 1, ConnectionId FBA1532AE06611E4BB10E7FDC5486EA5, SetupTime 16:22:57.795 UTC Sun Apr 12 2015, PeerAddress 0097150107659, PeerSubAddress , DisconnectCause 10 , DisconnectText normal call clearing (16), ConnectTime 16:23:02.015 UTC Sun Apr 12 2015, DisconnectTime 16:23:22.905 UTC Sun Apr 12 2015, CallOrigin 1, ChargedUnits 0, InfoType 2, TransmitPackets 1038, TransmitBytes 174384, ReceivePackets 1043, ReceiveBytes 166880
Apr 12 16:23:22.905: %VOIPAAA-5-VOIP_FEAT_HISTORY: FEAT_VSA=fn:TWC,ft:04/12/2015 16:22:57.785,cgn:4130,cdn:0097150107659,frs:0,fid:2601,fcid:FBA1532AE06611E4BB10E7FDC5486EA5,legID:284E,bguid:FBA1532AE06611E4BB10E7FDC5486EA5
Apr 12 16:23:25.317: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_name:
   lpcor endusers
Apr 12 16:23:25.317: //-1/xxxxxxxxxxxx/LPCOR/lpcor_get_index_by_name:
   lpcor endusers index 10
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#un all
All possible debugging has been turned off
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#
DAMAC-CME-ANOUD#!ok just send me these logs
DAMAC-CME-ANOUD#!i have to move from here
Apr 12 16:24:02.153: %VOIPAAA-5-VOIP_CALL_HISTORY: CallLegType 1, ConnectionId 14343755E06711E4BB16E7FDC5486EA5, SetupTime 16:23:25.323 UTC Sun Apr 12 2015, PeerAddress 4130, PeerSubAddress , DisconnectCause 10 , DisconnectText normal call clearing (16), ConnectTime 16:23:43.393 UTC Sun Apr 12 2015, DisconnectTime 16:24:02.153 UTC Sun Apr 12 2015, CallOrigin 2, ChargedUnits 0, InfoType 2, TransmitPackets 0, TransmitBytes 0, ReceivePackets 930, ReceiveBytes 148800
Apr 12 16:24:02.153: %VOIPAAA-5-VOIP_FEAT_HISTORY: FEAT_VSA=fn:Tnow
DAMAC-CME-ANOUD#\WC,ft:04/12/2015 16:23:25.321,cgn:4130,cdn:,frs:0,fid:2602,fcid:14343755E06711E4BB16E7FDC5486EA5,legID:2850,bguid:14343755E06711E4BB16E7FDC5486EA5
Apr 12 16:24:02.169: %VOIPAAA-5-VOIP_CALL_HISTORY: CallLegType 1, ConnectionId 14343755E06711E4BB16E7FDC5486EA5, SetupTime 16:23:39.169 UTC Sun Apr 12 2015, PeerAddress 0097150107659, PeerSubAddress , DisconnectCause 10 , DisconnectText normal call clearing (16), ConnectTime 16:23:43.389 UTC Sun Apr 12 2015, DisconnectTime 16:24:02.169 UTC Sun Apr 12 2015, CallOrigin 1, ChargedUnits 0, InfoType 2, TransmitPackets 930, TransmitBytes 156240, ReceivePackets 937, ReceiveBytes 149920
Apr 12 16:24:02.169: %VOIPAAA-5-VOIP_FEAT_HISTORY: FEAT_VSA=fn:TWC,ft:04/12/2015 16:23:39.169,cgn:4130,cdn:0097150107659,frs:0,fid:2603,fcid:14343755E06711E4BB16E7FDC5486EA5,legID:2851,bguid:14343755E06711E4BB16E7FDC5486EA5

We have come across this issue today in 10.9.5 (so affects 10.9.4 as well) but it was occurring in Sydney as well with a client and for me in Melbourne.

Adding Users from sharepoint into Active Directory Groups

I have a requirement for Approval Workflow where the Approved User gets added to AD group directly,i think 2 way sync is possible.plz help

Out of the box, I really doubt that this is possible BUT it can more than likely be achieved via the Object Model. A good discussion and some attached code can be seen here.
https://social.technet.microsoft.com/Forums/office/en-US/a1905a01-e7a7-458b-a7a6-d24cd4e19e09/action?threadDisplayName=add-a-user-in-ad-group-from-sharepoint
Steven Andrews
SharePoint Business Analyst: LiveNation Entertainment
Blog: baron72.wordpress.com
Twitter: Follow @backpackerd00d
My Wiki Articles:
CodePlex Corner Series
Please remember to mark your question as "answered" if this solves (or helps) your problem.

Adding and removing current user from one SharePoint group to another with event receiver

hi friends
i need to change current user from one SharePoint group to another with list item adding event receiver.
please help me

Hi Malli,
Greetings. Its nt possible
http://sharepoint.stackexchange.com/questions/42286/event-receivers-on-add-remove-users
Please remember to click 'Mark as Answer' on the answer if it helps you

Adding a cdrw to a non-global zone

Hi all,
I am attempting to add a cdrw on a laptop running Solaris 10 to a
non-global zone via the following (after browsing the archives of this
list as well as related forums and documentation):
"cdrw -l" when run in the global zone reports
"/dev/rdsk/c1t0d0s2" as the sole CD writer attached. I have previously
burnt cdr(s) using this, so the functionality of the drive is not an issue.
I then proceeded to configure a zone, "zulu01", and added a device via
the following using zonecfg (I have omitted the other configuration data
which is standard, root path, standard inherit-pkg-dir)
"add device"
"set match=/dev/rdsk/*"
"end"
"commit"
"verify"
I then installed the zone
"zoneadm -z zulu01 install"
zoneadm does the usual and reports success.
I boot the zone
"zoneadm -z zulu01 boot"
and login via "zlogin -C zulu01"
Inside zulu01, running "cdrw -l"
reports "No CD Writers found."
a "ls /dev/rdsk" shows that c1t0d0s2 is present.
I am aware that adding such a device is not recommended, but it is
supposedly possible?
Please advise on what I am doing wrong, or is it not possible to add a
cdrw to a non-local zone?
Thanks in advance.
Regards,
Jeremy.

This should work. A shot in the dark: can you try with another tool than cdrw, cdrecord for example? Also make sure that volume management is not running in the global zone (/etc/init.d/volmgt stop).
Blaise

Is it possible to have songs in the iTunes library that I do not want to be added to iTunes Match?

I ask this because a few days ago my iTunes library crashed and iTunes does not recognize my purchases anymore so I have a lot more than 25,000 songs in my library and instead of deleting 600 songs from my library, I would like to select some of them so they won't be added to iTunes Match. Does anybody know if this is possible?

I didn't say "re-create" I said "restore from a backup." Restoring from a backup will place all the files just as they were right back where they need to be. This includes the .itl, .itdb ad .xml files iTunes needs to recognize that the files on the internal HDD are the same as the files in the cloud.
You do have a backup, don't you? If you don't then I strongly recommend you start backing up immediately.
If all else fails you can email iTunes Store support and ask them to reset your iTunes Match DB on the server. This will require your iTunes to go through the entire scan, match and upload process as if it were the first time.

Adding polycom soundstation ip 7000 to cme 4.1...is it possible?

Similar Messages

Maybe you are looking for