Adding USB disk
I am having trouble getting my 802.11n AEBS to recognize my USB disk drive. I am using a Buffalo Drive Station which I have formatted as HFS+. I will almost never see the drive when I first power it on without restarting the AEBS. Even then it only sees it some of the time. When it does see it, the data transfers to it are so slow as to be unuseable (sometimes as slow a 100kBps or less). I noticed that Apple posted a page saying the AEBS only supports USB drives with a block size of 512 bytes. Does anyone know how to tell what the block size is? I can't find it in any of the documentation. Could this be why I am having trouble with this disk drive?
I have a similar problem, so maybe this can get answered at the same time.
I hooked up my Maxtor 1TB in Fat 32 and it won't work. I can see the drive, but the files are not accessable. For instance, when I click on my iTunes folder on that drive, it starts to list the files, then after a second, goes blank and at the bottom says "0 items, 41GB available".
I hooked up my Lacie 500GB supposedly in "AppleShare" or "Windows Sharing" or "SMB/CIFS" (are these drive formats?!?) and this drive works beautifully.
Do I have a) too many files? Or b) AEx has limited/no Fat 32 capability? Or c) something I'm overlooking?
Also, since my 1TB drive is packed, I'd have to buy another one to reformat!!!
Similar Messages
-
Folders added to USB disk connected to EA6700 not seen by Panasonic TV
Hello,
I have a Seagate 1.5TB USB ST315005EXA101-RK connected to EA6700.
The USB disk contains two folders with pictures, and they are fully visible in the Panasonic TV.
Today I added some other folders to the USB disk, but they are not seen in the Panasonic TV.
Shall I remove .tmp & cache folders in the USB disk in order to let EA6700 show all folders in the TV ?Sorry for not replying to this forum earlier. I have been busy with other tasks.
I disconnected the USB disk from EA6700, and connected it to my PC.
Then I removed .tmp and cache folders, and connected the disk back to EA6700.
Now I see all pictures on TV,
The lesson from this problem is to reconnect the disk to PC and remove .tmp & cache folders. -
USB disk access of every type is hosed - HELP!?
Newbie with the very latest "Don't Panic" running on a laptop. I'm coming off a year with various bloateddistros, looking for something fast and stable.
I've got my internal drive up, networking, x, gnome and openoffice all working great. Next step is to plug in my external 160gig drive with all my data on it. This is a very standard USB2-to-EIDE drive, I've had no problems with it in any distro. It's split between a 32gig FAT32 partition and a 119gig Ext3.
I followed the wiki on autofs. Nothing. Then played with HAL and the like. Made my user a member of group "storage". Still nothing.
I've seen mount problems before of course, so I tried adding gparted via pacman and running that from a root command line just to see what's physically out there. Not good: gparted never finishes getting past the "Scanning all devices....." process with the blue bar bouncing back and forth. When gparted first starts I can hear the external disk spin up and chug for a few seconds, but then nothing.
I tried a 1gig USB flash critter (probably Fat32), nothing there either. I think something is fundamentally hosed in my USB disk support. I do have a USB external trackball working though...so my ports are up.
My daemons at present:
DAEMONS=(syslog-ng network netfs crond ntpd hal cups gdm alunnd)
Heeeelp! Neeeed my daaaata!
Wait, something else weird: if I turn on the external disk I see some CPU activity on my gnome panel monitor. Nothing major, a few light spikes. I've got a Celeron 1.6 but with the new 533 memory bus and 2gigs RAM. Once I run gparted it goes bananas and then once I close gparted CPU activity is pegged hard at 100% - yet there's no listed process eating that. Then when I turn off the external drive, CPU activity falls back to normal.
WTF, over?
JimWell before reading Veek's post I got further along. Almost there I think.
I went and loaded XFCE4 plus extras, and logged in with a XFCE session. I like having a backup desktop environment anyways in case Gnome gets squirrelly.
In XFCE Thunar shows the disks, but when I try and access 'em I get:
Failed to mount "128G Volume".
(exo-mount:4613): Gtk-WARNING **: Locale not supported by C library.
Using the fallback 'C' locale.
You are not privileged to mount the volume "128G Volume".
What I can't figure out is, what permissions? I'm added to groups "storage" and "disks"...any more needed?
The output from fdisk -l:
bash-3.2$ fdisk -l
Disk /dev/sda: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 9729 78148161 83 Linux
Disk /dev/sdb: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 1 19457 156288321 5 Extended
/dev/sdb5 1 3824 30716217 b W95 FAT32
/dev/sdb6 3825 19457 125572041 83 Linux
bash-3.2$
I'm going to jump back to Gnome and try Veek's concepts... -
Can I watch iTunes-purchased movies from an Airport Extreme USB disk?
With the newest Airport firmware (7.6.1), it seems I should be able to do this.
My scenario is so basic, I can't understand why I'm having trouble achieving this.
- I have a MacBook Pro running OS X 10.7.2 - since it's a laptop, I don't want to leave it on all the time.
- I have an AirPort Extreme with a USB disk on it (that I use for backing up my MacBook), recently upgraded to newest firmware 7.6.1.
- I have a recently purchased Apple TV hard-wired to the AirPort running firmware 4.4.4.
- I have purchased movies though iTunes on the MacBook Pro.
I want to watch my iTunes-purchased movies on my Apple TV even when my MacBook Pro is sleeping. That is, I would like the movies to be accessible via iCloud, or stored on the USB disk connected to AirPort Extreme, or something/anything.
It seems obvious to me that with an all-Apple set up, and iCloud, this should be easy to achieve.
What am I missing?
Thanks,
jJasonFromSK wrote:
With the newest Airport firmware (7.6.1), it seems I should be able to do this.
Really? I need to check that out!
You should certainly be able to add content by reference to itunes from such a disk (even before the update) - so long as itunes knows the location of the file (set Preferences not to copy to local library when adding the media) it will stream it to AppleTV if the disk is available.
I hope you're right, but I'd be surprised if current Extremes can be upgarded to provide a full Home Sharing service - marvellous if they can but I'd be surprised as i've long said we need an Apple media server either based on TC or AE to do this kind of thing.
AC -
USB disk won't mount on startup (have tried everything)
Hi!
I'm having big problems getting my USB disk to mount on startup.:(
It used to work perfectly by having 'mount /dev/sdc1 /media/disk' in rc.local (and umount in local.shutdown) but recently it started saying that 'filesystem type must be defined' (or something like that). So I changed the line to 'mount -t ext3 /dev/sdc1 /media/disk' but now I get a message that '/dev/sdc1 does not exist'.
So I decided to get this fixed in fstab once and for all.
I checked the designations of the disks with 'fdisk -l' and noticed that the USB disk would alternate between /dev/sdc, /dev/sde and /dev/sdd quite random on every reboot. In other words I couldn't mount it in fstab by using one of those paths cause I'd get the same problem with '/dev/sdc or -e or -d does not exist'. I figured the sollution must be to mount the disk by using UUID. I checked the uuid's and got the following (as you can see the USB disk is on this reboot registered as '/dev/sde'):
bash-3.2$ ls -l /dev/disk/by-uuid/
total 0
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 6cf5e803-429a-44c3-bcf9-0f007df623f3 -> ../../sda1
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 8ef6be20-ee30-4a00-8946-56a4d94a7245 -> ../../sda3
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 947b3b86-8501-4011-9da2-4de45eb4ed60 -> ../../sda2
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 94911fb3-def7-4440-b6a5-5e09f91b19f6 -> ../../sde1
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 acd197d3-f63e-48f9-88de-41eff1b3b425 -> ../../sda4
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 b6745703-bde6-44ef-865d-d09501ecc8ab -> ../../sdb1
I other words the UUID of the disk should be '94911fb3-def7-4440-b6a5-5e09f91b19f6' so I added that to the fstab file, but I still get the same error that the disk doesn't exist. How is this possible? Isn't the UUID supposed to be the same no matter what? When the disk is clearly labeled with this UUID every time I check it why can't it be used in fstab??
Here's my fstab (I've commented out the lines that I've been trying out):
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
none /dev/pts devpts defaults 0 0
none /dev/shm tmpfs defaults 0 0
/dev/cdrom /mnt/cdrom iso9660 ro,user,noauto,unhide 0 0
/dev/dvd /mnt/dvd udf ro,user,noauto,unhide 0 0
/dev/sda1 /boot ext2 defaults 0 1
/dev/sda2 / ext3 defaults 0 1
/dev/sda3 /var reiserfs defaults 0 1
/dev/sda4 /home ext3 defaults 0 1
/dev/sdb1 /extra ext3 defaults 0 1
#/dev/sdc1 /media/disk defaults 0 0
#UUID=94911fb3-def7-4440-b6a5-5e09f91b19f6 /media/disk defaults 0 0
What am I doing wrong here? I've also tried to use different options like 'rw,auto,exec' but it won't work.It seems I'm able to mount the disk from the terminal by doing '# sudo mount UUID=94911fb3-def7-4440-b6a5-5e09f91b19f6 /media/disk'.
But this only works when I do it manually. Adding 'mount UUID=94911fb3-def7-4440-b6a5-5e09f91b19f6 /media/disk' to rc.local only gives the error that filesystem must be defined and when it's defined I get the error that device is not found.
How can it work manually, but not in fstab or rc.local?
Here's my dmesg:
BIOS EBDA/lowmem at: 0009f800/0009f400
Linux version 2.6.28-ARCH (root@T-POWA-LX) (gcc version 4.3.3 (GCC) ) #1 SMP PREEMPT Mon Feb 2 22:22:59 UTC 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.4 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working it around.
last_pfn = 0x7fef0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009f400 (usable)
modified: 000000000009f400 - 00000000000a0000 (reserved)
modified: 00000000000f0000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000007fef0000 (usable)
modified: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
modified: 000000007fef3000 - 000000007ff00000 (ACPI data)
modified: 00000000e0000000 - 00000000f0000000 (reserved)
modified: 00000000fec00000 - 0000000100000000 (reserved)
kernel direct mapping tables up to 377fe000 @ 10000-16000
RAMDISK: 7fe0e000 - 7fedf2e4
Allocated new RAMDISK: 0055f000 - 006302e4
Move RAMDISK from 000000007fe0e000 - 000000007fedf2e3 to 0055f000 - 006302e3
ACPI: RSDP 000F8600, 0014 (r0 HP-CPC)
ACPI: RSDT 7FEF3040, 0038 (r1 HP-CPC AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 7FEF30C0, 0084 (r2 HP-CPC AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 7FEF31C0, 3C55 (r1 HP-CPC AWRDACPI 1000 MSFT 100000E)
ACPI: FACS 7FEF0000, 0040
ACPI: SSDT 7FEF6F40, 01CA (r1 HP-CPC POWERNOW 1 LTP 1)
ACPI: SRAT 7FEF7180, 00A0 (r1 HP-CPC HAMMER 1 AMD 1)
ACPI: MCFG 7FEF7280, 003C (r1 HP-CPC AWRDACPI 42302E31 AWRD 0)
ACPI: APIC 7FEF6E80, 0068 (r1 HP-CPC AWRDACPI 42302E31 AWRD 0)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 00000000 - 377fe000
bootmap 00012000 - 00018f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 000055b520] TEXT DATA BSS ==> [0000100000 - 000055b520]
#4 [000055c000 - 000055f000] INIT_PG_TABLE ==> [000055c000 - 000055f000]
#5 [000009f400 - 0000100000] BIOS reserved ==> [000009f400 - 0000100000]
#6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
#7 [000055f000 - 00006302e4] NEW RAMDISK ==> [000055f000 - 00006302e4]
#8 [0000012000 - 0000019000] BOOTMAP ==> [0000012000 - 0000019000]
found SMP MP-table at [c00f46e0] 000f46e0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007fef0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0007fef0
On node 0 totalpages: 523903
free_area_init_node: node 0, pgdat c0406600, node_mem_map c1000200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2318 pages used for memmap
HighMem zone: 294372 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
SB4X0 revision 0x11
Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 7ff00000:60100000)
PERCPU: Allocating 36864 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519809
Kernel command line: root=/dev/sda2 ro quiet
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 2188.552 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Scanning for low memory corruption every 60 seconds
Memory: 2072040k/2096064k available (2227k kernel code, 22632k reserved, 1026k data, 332k init, 1186760k highmem)
virtual kernel memory layout:
fixmap : 0xffee8000 - 0xfffff000 (1116 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc0433000 - 0xc0486000 ( 332 kB)
.data : 0xc032cfd9 - 0xc042db5c (1026 kB)
.text : 0xc0100000 - 0xc032cfd9 (2227 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 4378.48 BogoMIPS (lpj=7295173)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080926
ACPI: Checking initramfs for custom DSDT
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4379.66 BogoMIPS (lpj=7295468)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01
Brought up 2 CPUs
Total of 2 processors activated (8757.15 BogoMIPS).
net_namespace: 768 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 18 io port: [0x4100-0x411f]
pci 0000:00:00.0: reg 1c 64bit mmio: [0xe0000000-0xffffffff]
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:12.0: reg 10 io port: [0xfe00-0xfe07]
pci 0000:00:12.0: reg 14 io port: [0xfd00-0xfd03]
pci 0000:00:12.0: reg 18 io port: [0xfc00-0xfc07]
pci 0000:00:12.0: reg 1c io port: [0xfb00-0xfb03]
pci 0000:00:12.0: reg 20 io port: [0xfa00-0xfa0f]
pci 0000:00:12.0: reg 24 32bit mmio: [0xfe02f000-0xfe02f1ff]
pci 0000:00:12.0: reg 30 32bit mmio: [0x000000-0x07ffff]
pci 0000:00:12.0: supports D1 D2
pci 0000:00:13.0: reg 10 32bit mmio: [0xfe02e000-0xfe02efff]
pci 0000:00:13.1: reg 10 32bit mmio: [0xfe02d000-0xfe02dfff]
pci 0000:00:13.2: reg 10 32bit mmio: [0xfe02c000-0xfe02cfff]
pci 0000:00:13.2: supports D1 D2
pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.2: PME# disabled
pci 0000:00:14.0: reg 10 io port: [0x500-0x50f]
pci 0000:00:14.0: reg 14 32bit mmio: [0xfe02b000-0xfe02b3ff]
HPET not enabled in BIOS. You might try hpet=force boot option
pci 0000:00:14.1: reg 10 io port: [0x00-0x07]
pci 0000:00:14.1: reg 14 io port: [0x00-0x03]
pci 0000:00:14.1: reg 18 io port: [0x00-0x07]
pci 0000:00:14.1: reg 1c io port: [0x00-0x03]
pci 0000:00:14.1: reg 20 io port: [0xf800-0xf80f]
pci 0000:01:00.0: reg 10 32bit mmio: [0xfa000000-0xfaffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xfb000000-0xfbffffff]
pci 0000:01:00.0: reg 24 io port: [0xef00-0xef7f]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:00:02.0: bridge io port: [0xe000-0xefff]
pci 0000:00:02.0: bridge 32bit mmio: [0xfa000000-0xfcffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:02:01.0: reg 10 io port: [0xdf00-0xdfff]
pci 0000:02:01.0: supports D1 D2
pci 0000:02:03.0: reg 10 io port: [0xde00-0xdeff]
pci 0000:02:03.0: reg 14 32bit mmio: [0xfdeff000-0xfdeff0ff]
pci 0000:02:03.0: reg 30 32bit mmio: [0x000000-0x00ffff]
pci 0000:02:03.0: supports D1 D2
pci 0000:02:03.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:02:03.0: PME# disabled
pci 0000:02:04.0: reg 10 32bit mmio: [0xfdefe000-0xfdefe7ff]
pci 0000:02:04.0: reg 14 io port: [0xdd00-0xdd7f]
pci 0000:02:04.0: supports D2
pci 0000:02:04.0: PME# supported from D2 D3hot D3cold
pci 0000:02:04.0: PME# disabled
pci 0000:00:14.4: transparent bridge
pci 0000:00:14.4: bridge io port: [0xd000-0xdfff]
pci 0000:00:14.4: bridge 32bit mmio: [0xfde00000-0xfdefffff]
pci 0000:00:14.4: bridge 32bit mmio pref: [0xfdd00000-0xfddfffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
PCI: Using ACPI for IRQ routing
pci 0000:00:00.0: BAR 3: can't allocate resource
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:09: mem resource (0xf0000-0xf3fff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0xf4000-0xf7fff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0xf8000-0xfbfff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0xfc000-0xfffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0x0-0x9ffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0x100000-0x7feeffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: ioport range 0x228-0x22f has been reserved
system 00:01: ioport range 0x40b-0x40b has been reserved
system 00:01: ioport range 0x4d6-0x4d6 has been reserved
system 00:01: ioport range 0xc00-0xc01 has been reserved
system 00:01: ioport range 0xc14-0xc14 has been reserved
system 00:01: ioport range 0xc50-0xc52 has been reserved
system 00:01: ioport range 0xc6c-0xc6d has been reserved
system 00:01: ioport range 0xc6f-0xc6f has been reserved
system 00:01: ioport range 0xcd4-0xcdf has been reserved
system 00:01: ioport range 0x4000-0x40fe has been reserved
system 00:01: ioport range 0x4210-0x4217 has been reserved
system 00:06: ioport range 0x4d0-0x4d1 has been reserved
system 00:06: ioport range 0x800-0x87f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0x7ff00000-0x7fffffff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfff80000-0xfffeffff has been reserved
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xe000-0xefff
pci 0000:00:02.0: MEM window: 0xfa000000-0xfcffffff
pci 0000:00:02.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:14.4: PCI bridge, secondary bus 0000:02
pci 0000:00:14.4: IO window: 0xd000-0xdfff
pci 0000:00:14.4: MEM window: 0xfde00000-0xfdefffff
pci 0000:00:14.4: PREFETCH window: 0x000000fdd00000-0x000000fddfffff
pci 0000:00:02.0: setting latency timer to 64
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffff]
bus: 01 index 0 io port: [0xe000-0xefff]
bus: 01 index 1 mmio: [0xfa000000-0xfcffffff]
bus: 01 index 2 mmio: [0xd0000000-0xdfffffff]
bus: 01 index 3 mmio: [0x0-0x0]
bus: 02 index 0 io port: [0xd000-0xdfff]
bus: 02 index 1 mmio: [0xfde00000-0xfdefffff]
bus: 02 index 2 mmio: [0xfdd00000-0xfddfffff]
bus: 02 index 3 io port: [0x00-0xffff]
bus: 02 index 4 mmio: [0x000000-0xffffffff]
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 836k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1732
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:00.0: MSI quirk detected; MSI disabled
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:02.0: setting latency timer to 64
pcieport-driver 0000:00:02.0: found MSI capability
pci_express 0000:00:02.0:pcie00: allocate port service
pci_express 0000:00:02.0:pcie01: allocate port service
pci_express 0000:00:02.0:pcie03: allocate port service
aer 0000:00:02.0:pcie01: AER service couldn't init device: no _OSC support
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /class/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 332k freed
SCSI subsystem initialized
libata version 3.00 loaded.
pata_acpi 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
pata_acpi 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
scsi0 : pata_atiixp
scsi1 : pata_atiixp
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf800 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf808 irq 15
ata2.00: ATAPI: HP DVD Writer 740b, ED24, max UDMA/33
ata2.00: configured for UDMA/33
scsi 1:0:0:0: CD-ROM HP DVD Writer 740b ED24 PQ: 0 ANSI: 5
sata_sil 0000:00:12.0: version 2.3
scsi2 : sata_sil
scsi3 : sata_sil
ata3: SATA max UDMA/100 mmio m512@0xfe02f000 tf 0xfe02f080 irq 22
ata4: SATA max UDMA/100 mmio m512@0xfe02f000 tf 0xfe02f0c0 irq 22
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-8: SAMSUNG HD501LJ, CR100-10, max UDMA7
ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/100
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7: WDC WD2500JS-60MHB1, 10.02E01, max UDMA/100
ata4.00: 488397168 sectors, multi 16: LBA48
ata4.00: configured for UDMA/100
scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5
scsi 3:0:0:0: Direct-Access ATA WDC WD2500JS-60M 10.0 PQ: 0 ANSI: 5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:13.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe02c000
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<6>ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 19, io mem 0xfe02e000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ohci_hcd 0000:00:13.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 19, io mem 0xfe02d000
sda1 sda2 sda3 sda4
sd 2:0:0:0: [sda] Attached SCSI disk
sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI disk
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
usb 1-7: new high speed USB device using ehci_hcd and address 5
usb 1-7: configuration #1 chosen from 1 choice
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 242 bytes nvram
usb 2-2: new low speed USB device using ohci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
8139too Fast Ethernet driver 0.9.28
8139too 0000:02:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
eth0: RealTek RTL8139 at 0xf8182000, 00:13:d3:88:fb:ec, IRQ 20
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
lirc_dev: IR Remote Control driver registered, major 61
lirc_mceusb2: Philips eHome USB IR Transceiver and Microsoft MCE 2005 Remote Control driver for LIRC $Revision: 1.44 $
lirc_mceusb2: Daniel Melander <[email protected]>, Martin Blatter <[email protected]>
usbcore: registered new interface driver lirc_mceusb2
usb 3-1: new full speed USB device using ohci_hcd and address 2
C-Media PCI 0000:02:01.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
usb 3-1: configuration #1 chosen from 1 choice
input: Power Button (FF) as /class/input/input1
usb 3-1: reset full speed USB device using ohci_hcd and address 2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input2
ACPI: Power Button (CM) [PWRB]
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
processor ACPI_CPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
lirc_dev: lirc_register_plugin: sample_rate: 0
lirc_mceusb2[2]: Philips eHome Infrared Transceiver on usb3:2
usb 3-2: new low speed USB device using ohci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
usb 3-4: new full speed USB device using ohci_hcd and address 4
usb 3-4: configuration #1 chosen from 1 choice
Linux agpgart interface v0.103
usbcore: registered new interface driver hiddev
scsi 1:0:0:0: Attached scsi generic sg0 type 5
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 3:0:0:0: Attached scsi generic sg2 type 0
input: Logitech HID compliant keyboard as /class/input/input3
generic-usb 0003:046D:C30E.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech HID compliant keyboard] on usb-0000:00:13.0-2/input0
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
input: Logitech HID compliant keyboard as /class/input/input4
generic-usb 0003:046D:C30E.0002: input,hidraw1: USB HID v1.10 Device [Logitech HID compliant keyboard] on usb-0000:00:13.0-2/input1
input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /class/input/input5
generic-usb 0003:045E:0047.0003: input,hidraw2: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:13.1-2/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nvidia: module license 'NVIDIA' taints kernel.
piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x500, revision 0
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
input: PC Speaker as /class/input/input6
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi5 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
ohci1394 0000:02:04.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[fdefe000-fdefe7ff] Max Packet=[2048] IR/IT contexts=[4/8]
Error: Driver 'pcspkr' is already registered, aborting...
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
nvidia 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 180.22 Tue Jan 6 09:29:08 PST 2009
EXT3 FS on sda2, internal journal
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc0000bc42b8]
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
scsi 5:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
sd 5:0:0:0: [sdc] Attached SCSI removable disk
sd 5:0:0:0: Attached scsi generic sg3 type 0
scsi 5:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
scsi 4:0:0:0: Direct-Access ST316002 3A 8.01 PQ: 0 ANSI: 0
sd 5:0:0:1: [sdd] Attached SCSI removable disk
sd 5:0:0:1: Attached scsi generic sg4 type 0
scsi 5:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
sd 4:0:0:0: [sde] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
sd 4:0:0:0: [sde] Assuming drive cache: write through
sd 4:0:0:0: [sde] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
sd 4:0:0:0: [sde] Assuming drive cache: write through
sde: sde1
sd 4:0:0:0: [sde] Attached SCSI disk
sd 4:0:0:0: Attached scsi generic sg5 type 0
usb-storage: device scan complete
sd 5:0:0:2: [sdf] Attached SCSI removable disk
sd 5:0:0:2: Attached scsi generic sg6 type 0
scsi 5:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
sd 5:0:0:3: [sdg] Attached SCSI removable disk
sd 5:0:0:3: Attached scsi generic sg7 type 0
usb-storage: device scan complete
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
kjournald starting. Commit interval 5 seconds
EXT3 FS on sde1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
TCP(wget:15427): Application bug, race in MSG_PEEK.
TCP(wget:18681): Application bug, race in MSG_PEEK.
TCP(wget:4122): Application bug, race in MSG_PEEK.
TCP(wget:4275): Application bug, race in MSG_PEEK.
TCP(wget:19451): Application bug, race in MSG_PEEK. -
My Airport Extreme disconnects randomly when USB disk is attached, I have searched this forum but found now obvious solution.
The Airport Extreme has the latest firmware.
Since the airdisk solution is quite useless at this time, I would kindly accept any kind of help .....thanks
SieberLen61 got my reply, I have copied below.
Hi - I have been on the phone with support 4X since late December - all good calls. They have been scratching their heads on this issue.
I have 2 printers and 2 drives on the airport -recent experieinces = printers have always behaved, drives have appeared / vanished / "drive needs repair" and it's just fine...
Cutting out the interim fixes, here are the simple but important solutions and everything has been stable for days now.
* rolled back to AEBS firmware 7.1.1
* replaced the passive USB hub with a powered hub ** This is when joy arrived
* make sure your drive has a block size of 512
You can run guest mode however you want, since adding the new hub, it hasn't mattered.
I haven't been brave enough to upgrade firmware to 7.2.1
cheers -
Using airport utilithy 6.1, i've enabled file sharing and added a disk password. all looks good, but i don't see the disk in finder. Any ideas folks?
Checkpoints:
The disk should be formatted in Mac OS Extended (Journaled)
If the disk is formatted correctly, a number of users....me included...are reporting that they must use a powered USB hub with the AirPort Extreme to compensate for the borderline power at the USB port of the AirPort Extreme....even if the hard drive has its own separate power supply
If the drive is formatted correctly and has sufficient power, the AirPort Extreme icon will appear under the SHARED heading in the Finder
Click on the AirPort Extreme icon and a folder representing the hard drive will appear in the window to the right
Double click the folder to mount the drive on the desktop.
Note.....you may need to click "Connect As" the first time that you do this and enter the disk password to connect. -
AEBSn + USB disk, not visible in Windows
Have been using AEBSn as access point for last 6 months. Now added a LaCie MacMini drive via the USB port on AEBSn but am unable to access it via the LAN. I know this is a common problem and have checked the settings described in some of the responses to no avail.
The disk is formatted as HFS and can be accessed using MacDrive when directly attached to PC. The disk name is currently "Lemon" (so no funny characters).
AEBSn has latest firmware (7.2.1), the disk is visible under "disks" on the Airport Utility, file sharing is enabled with base station password, guest access is read & write and disks are advertised globally using Bonjour.
I have tried to access from three different PCs. The latest Bonjour (1.0.4) is loaded and is enabled in firewall (AVG in 2 and Windows in other). From Windows Explorer I can see the AEBS (properties shows it as a CIFS server) but it has no folders. The Airport Disk Agent is running in the system tray but does not detect any disks.
Please help, my central back strategy is in ruins!Hi, I just got my usb disk working!
I got Airport Extreme (the latest one), all the firmware updates (7.2.1) one pc with WINXP. A 500Gb USB disk from Packard Bell. I want to connect the drive to the Airport and serve files over the wireless.
my trouble was that while I could see the disk in airport utility, I could not actually connect: wrong password, user etc.
As the disk is visible in Airport Utility and the Extreme station is visible in the disk management utility in the status bar, I concluded that there must be a problem outside of the Airport Extreme. Indeed, this I found to be in my network settings, which I easily fixed by installing Microsoft Client for Networks. Practically I did this by Start>Network settings right click Properties. then selected the wireless network right click properties once more. Under the General tab I checked for the presence of Microsoft Client for Networks, it wasn't there so on the same screen I click Install.. select Clients and fianlly Microsoft Client for Networks. Bingo.
I hope this helps, I spent a whole day looking around in this forum and no one has suggested this. So I do and wish you good luck! (now to see if I can get the music onto my Airport Express!!!) -
Performance of WRT610N (v1) with attached USB disk
Greetings, I've had my WRT610N for a while now and have had no complaints on performance. Over this past weekend, however, I attached a USB disk to it (cheaper than adding a NAS). I can mount it without problem on my Vista box, but it seems that when the disk is being accessed (read or write), I get severe performance degradation on my network connection. Severe enough to render the network unusable.
Is this to be expected? Is there a setting in the firmware that will prioritize network activity over disk activity?
The PCs in question are wired and the router is running the latest firmware (1.00.03.15). The disk (previously formatted on my computer) is NTFS. If there are any other pertinent pieces of information, please let me know.
Thanks.
Message Edited by msfeinstein on 10-05-2009 04:27 PMTry reducing the MTU size to 1300 on the router's GUI and check if the problem resolve...If not then,try upgrading/reflashing the router's firmware and reconfigure it from the scratch....
-
Can't share sd card as usb disk
I'm running FirefoxOs 1.1 on an Alcatel Fire. I have activated the two options needed to share the sd card (which is working fine) as a usb disk but my computer (Debian) doesn't recognize it. When I connect the phone it creates an sdb entry in /dev but with no partition (sdb1).
So far, the only way of achieving this is by issuing the command described here (http://yorik.uncreated.net/guestblog.php?2014=15) under "Adding usb access to sdcard" > step 5. I have to do this every time I connect the phone, of course.
Additional information:
- The sd card is working fine. I can use it on the computer with a microsd adapter.
- The sd card works fine on the phone also.
- I have enabled the usb disk and shared the sd card in the phone.
- The page I linked says the partition should appear when I unlock the home screen, I did try that but it still doesn't work.Hi lufte,
Thank you for your question. This forum is meant for use cases, and this may be a question for stackoverflow.com
Have you enabled USB storage on the Settings option, are there other apps using the storage and have you rooted the phone?
[https://bugzilla.mozilla.org/show_bug.cgi?id=994376]
Looking forward to your reply. -
Only Certain files on USB disks not recognized
Hi all:
At first, my macbook was unable to recognize some files in 2 particular folders on my usb disks (Western Digital 250 and 500)... then, following an update, they now seem to be working fine.
Since, I have added a Windows XP desktop directly to the router (wired)... the Windows desktop will not read the information in the same 2 folders. You can see the folders and click on them, but the information inside the folders does not display... Other folders on the same disks work fine.
Both are disks are FAT32 formatted... the folders are large and contain videos.
Any ideas?
Thanks...Many people seem to be having this problem. What seems to help is plugging in the disk into the AEBS and created a new empty folder. Then plug it into your windows machine. Copy everything that was in the root of the drive to that new folder. Plug it back into the the AEBS and everything should show up now. I know it is a pain in the ***, but this seems to work...
-
GNOME, nautilus, devicekit-disks: mount USB disk
Hi,
I recently upgraded and have now nautlius 2.28.2-1 together with devicekit-disks 009-1 installed.
As usual mounting/unmounting USB disks in nautilus stopped working. I searched the wiki, forums, bugs and google to gather information about this topic, but you know ...
When I try to mount a disk (they all show up in nautilus) nautilus pops up an error declaring me "Not Authorized". After quite some reading I think nautilus now uses devicekit-disks to actually mount my USB disks, so I tried to mount it with devicekit-disks:
[resi@nomad ~]$ devkit-disks --mount /dev/sdc
Mount failed: Not Authorized
In older versions of nautilus I used to edit some files in /etc to grant myself permissions (PolicyKit.conf), but this does not work anymore.
I found a hint and edited /usr/share/polkit-1/actions/org.freedesktop.devicekit.disks.policy (this one is coming with devicekit-disks) and modified the default for the actions org.freedesktop.devicekit.disks.filesystem-mount action:
<allow_any>yes</allow_any>
Having done so I can now mount the USB disks using nautilus, devicekit-disks or palimpsest (suffering from the same "Not Authorized" problem). Unmounting has a little flaw though, it seems like nautilus tries to eject the medium when unmounting, but then again its "Not Authorized" to do so.
However, this is the only solution I could come up with. Since the file I modified will probably be replaced without notice during the next upgrade I fear I will have to go all the way again, not remembering anymore what I did to fix this (otoh, after writing this I probably will).
And since the values in org.freedesktop.devicekit.disks.policy are declared as defaults (and by the fact it lives under /usr) I assume there has to be a site configuration file somewhere in /etc.
Where should I but my customizations? I mean, whats the proper way to do so?
Thanks,
Christoph
P.S.: I like nautilus, it makes me unhappy to use thunar/pmount/whatever to mount my disks.me again ... this whole *kit stuff seems so odd to me.
I finally read all the devicekit, then the policykit docs, Syu-ed and have now devicekit-disks 009-3 installed.
Using polkit-actions without arguments prints a list of registered actions (known to policykit). This list was pretty short:
[resi@nomad ~]$ polkit-action
org.freedesktop.policykit.read
org.freedesktop.policykit.revoke
org.freedesktop.policykit.grant
org.freedesktop.policykit.modify-defaults
PolicyKit considers all *.policy files under /usr/share/PolicyKit/policy/, only the policykit package installs its files (well, its one file) there.
devicekit-disks (and probably some other packages providing *.policy files) seems to forget about that. So I added a symlink:
[root@nomad policy]# ln -s /usr/share/polkit-1/actions/org.freedesktop.devicekit.disks.policy /usr/share/PolicyKit/policy/
Thats not enough, the file seems to be out of date. I had to replace all auth_admin_keep defaults with auth_admin_keep_session until the file validated.
And hurray:
[resi@nomad ~]$ polkit-action
org.freedesktop.policykit.read
org.freedesktop.policykit.revoke
org.freedesktop.policykit.grant
org.freedesktop.policykit.modify-defaults
org.freedesktop.devicekit.disks.filesystem-mount
org.freedesktop.devicekit.disks.filesystem-mount-system-internal
org.freedesktop.devicekit.disks.filesystem-check
org.freedesktop.devicekit.disks.filesystem-check-system-internal
org.freedesktop.devicekit.disks.filesystem-unmount-others
org.freedesktop.devicekit.disks.filesystem-lsof
org.freedesktop.devicekit.disks.filesystem-lsof-system-internal
org.freedesktop.devicekit.disks.drive-eject
org.freedesktop.devicekit.disks.drive-detach
org.freedesktop.devicekit.disks.change
org.freedesktop.devicekit.disks.change-system-internal
org.freedesktop.devicekit.disks.drive-ata-smart-refresh
org.freedesktop.devicekit.disks.drive-ata-smart-selftest
org.freedesktop.devicekit.disks.drive-ata-smart-retrieve-historical-data
org.freedesktop.devicekit.disks.luks-unlock
org.freedesktop.devicekit.disks.luks-lock-others
org.freedesktop.devicekit.disks.linux-md
org.freedesktop.devicekit.disks.cancel-job-others
org.freedesktop.devicekit.disks.inhibit-polling
org.freedesktop.devicekit.disks.drive-set-spindown
polkit-auth shows my authorizations, thus:
[resi@nomad ~]$ polkit-auth | grep mount
org.freedesktop.devicekit.disks.filesystem-mount
org.freedesktop.devicekit.disks.filesystem-mount-system-internal
org.freedesktop.devicekit.disks.filesystem-unmount-others
It seems to me that I am authorized for all actions listed above, I guess thats because this user is in both the wheel and root groups.
However, when I try to actually mount something nothing has changed.
[resi@nomad ~]$ devkit-disks --mount /dev/sdc
Mount failed: Not Authorized
Since policykit is now properly configured I can use polkit-action or polkit-gnome-authorization to modify the default values in the way polkit expects me to (not tampering with with the *.policy files).
[resi@nomad ~]$ polkit-action --action org.freedesktop.devicekit.disks.filesystem-mount
action_id: org.freedesktop.devicekit.disks.filesystem-mount
description: Mount a device
message: Authentication is required to mount the device
default_any: yes (factory default: no)
default_inactive: yes (factory default: no)
default_active: yes
But even now mounting fails because I'm not authorized.
Back to the start, if I change the factory defaults in org.freedesktop.devicekit.disks.policy mounting succeeds.
I think there might be 2 bugs involved here:
1.) missing links to policy files in /usr/share/PolicyKit/policy/
2.) policykit fails to consider overrides for factory defaults
What do you think? -
How to control DE USB disk Automounts.
Hi,
Can someone please guide me as to how to 'control' Automounts by DE when we plug USB disk drives.
I have KDE4 on my Arch system. When I connect a pen drive/USB HDD which is formatted as vfat/NTFS, the system(or KDE) 'Automounts' it in /media and I have read/write access to it. But if I use the same drive and format it as ext4, it wont be mounted as read/write for normal users but only for root.
Now pen drives and USB HDD's are removable storage drives and hence are volatile and could not have a fixed mount point, so it cannot be mounted by putting an entry in fstab or could they?. And I need my USB HDD frequently, and manually mounting it through CLI everytime and working on it as root is a bad idea i guess.
I am posting this because m confused as to how to control this Automount feature-What is the backend to it? Because I've read that HAL no longer takes care of it and that HAL will be deprecated soon, instead UDEV takes care of it. If that is the case then should I be concerned about polkit? Because that is what's the output provided by Dolphin(freedesktop.org policy prevented blah blah).
Another thing is if HAL is still in use and Automounts my devices then is it independent or polkit is a part of it. Then, is using hal-easy an option or replacement to standard HAL. ??!!??
I tried HAL archwiki and used the code to give a user permission to give rw access to automounted ext filesystems, but then nothing is mounted, it sings the same old freedesktop.org prevented bla blah song. And I think this is a question for all linuxes using Gnome and KDE in general.
Any help is appreciated.If by 'ability to mount as user' you mean to mount it manually but read/write access to normal users then yes. But primarily I need automounting as user, also be able to give access to other users for read/write et filesystem automounts.
Last edited by kapz (2009-11-17 01:12:56) -
Time Machine times-out on external USB disk, but works on 2 others
Hello,
I wanted to share my experience, in case it is helpful to someone else. It appears that one of my external hard disks has a hardware fault, or that TM is overly sensitive to its state, thus preventing me using it for backup.
After upgrading from Tiger to Leopard on my Macbook Pro 2.16GHz, I had been trying over the last couple of days, without success, to backup using Time Machine to an external USB hard disk at work. It is a Maxtor disk in a BlueEye U235 case. On each attempt to make the initial backup, TM would copy between 2 and 25GB of data (of 75 total) to the disk, and then stall indefinately, without giving an error. (Ejecting the disk at this point and restarting the computer just lead to further problems with completing the backup that I won't go into here). I tried many times, each time reformatting the disk (with the GUID partition map), deleting the TM preference file, restarting and ensuring all other apps were not running. I was completely fed-up!
I subsequently tried backing up for the first time on a freshly re-partitioned (GUID map) Firewire 400 external disk (Prolific PL3507 Combo Device in a BlueEye O2 case) at home, and this worked perfectly the first time, taking a couple of hours. (All applications were closed at the time). Subsequent backups to this drive work fine.
I tried again with the disk at work and it continued to fail. Finally I decided to follow what was being thrown up to the system.log. I discovered that shortly after TM was stalling (somewhere between 10 and 40 mins after commencing the backup), repeated messages would appear in system.log saying "kernel IOSCSIPeripheralDeviceType00::setPowerState(0x4cbe100, 2 -> 1) timed out after 100683 ms" (with the "2 - > 1" and number of ms different each time), with a few minutes between each one. This suggested to me that there was some sort of intermittent failure of the disk, or the connection between the Macbook Pro and the disk, or something I don't understand. It is worth keeping in mind that this disk has been working perfectly for me - I've been backup up entire system to it every couple of days using SuperDuper, without any errors or problems.
So, I then tried using a different (LaCie) Firewire disk at work, and after reformatting / partitioning (GUID map), the backup to this worked perfectly the first time, with the entire ~68 GB completing in about 2 hours. (As an aside, switching between the TM backup disks at Home and Work works well - TM just catches up from where it last left off on the particular drive).
The message I wanted to convey is that, in my experience, TM may fail during a backup (stall in fact, as no explicit message was generated) to a disk that outwardly appears to be fully functional. I'm not sure if in my case there is a minor error with the disk, a fault with TM, or both. Interestingly, upon bringing the disk home today and switching it on it won't mount at all, on my computer or that of my partner. I'm not sure if the problems with TM were therefore indicative of imminent disk failure, or whether the trip home in the pannier on my bike has damaged the drive . So, if you're having this or some other difficulty, on a drive that you haven't purchased new, it may be worth considering that an unsuccessful TM backup may be due to a current, or imminent, problem with the disk.
Just my two cents worth.Yes, I think you have a good point. The motivation for my post was just to make people aware - as there seems to be many people having problems with TM - that maybe the first drive you try, particularly if it is not new, may not work and that it is worth trying another if you can. Particularly in light of the fact that I didn't receive any explicit error messages, that is other than the one in the system.log file.
The USB disk was powered separately and was plugged directly into one of my USB ports (not via a hub). At the same time a USB mouse was plugged in. I think it is USB 2, but I'm not sure, and as it is not working now, I don't know how to check.
The rate at which data is copied to the two drives that work (via Firewire 400) seemed to be quite similar to the rate for the USB drive, until it bombed out. -
How do I move old Time Machine backups to new USB disk
Hi,
I purchased a new 1TB USB disk and want to keep my historic backups. I remember trying this a while ago when I moved disks and ended up giving up. Anyone care to tell me the steps I need to step on ?
cheers
AdamSee #18 in the Frequently Asked Questions *User Tip* at the top of this forum.
Maybe you are looking for
-
Error While Releasing the Billing Doc to Accounting.
Hi All, When I am Releasing the Billing Document to Accounting the Value of JIN2 Condition Type is not getting released to Accounting. It is giving the Following Error.FI/CO Interface : Balance in Transaction Currency. I have all maintaine
-
Document crashed in InDesign 5.5- it will not open
I have a doc that just crashed my ID5.5. It will not open, ID "does not respond" and I have to force quit. I cleaned out the preferences, I tried opening the file on another computer. Nothing works. I posted the crash report. Can anyone help? http://
-
Front Row displays a video name thats been deleted...
I've deleted a movie on my mac, I go into Front Row>Videos>Movies and the file name is still there, anyone had the same problem or does anyone know how to get rid of this? Thanks, Andy
-
As a Network Administrator, I should know the answer to this question. How can I send a message directly to the screen of all the users on my domain about system outages or other important messages on my 2003 Windows Network? I know there is a way, b
-
hi Gurus , i am facing a very strange problem i have update couple of z fields in master table VBAK i am writing a normal update statements but it is not updating the value of that field and setting the sy-subrc to 4 . i am passing just the vbeln in