Additional effects and amp models for guitar

Do the jam packs include additional amp models and effects or presets? Granted I'm new to GB, but in 2 whole weeks I haven't been able to create 1 acceptable tone using my guitar (real instrument).
Typically, I stay within 4 tones on my practice tube amp. Dirty, clean, and both with slight chorus/reverb/flanger. Standard stuff that I can't seem to come even close to recreating in GB.
I'm looking for an Octave divider as well. Also, can you play bassline on a guitar and drop it 1-2 octaves? Wors't case I assume I could play the line and manually move the note down, right?
Thanks a lot.

I think there are more amps in the JPs, but I don't have any of them. I have heard some good sounds from folks using the amps in GB, but I mic my amp to get my sound. You can open the manual control for each amp and tweak them like you would a real amp. Have you done that? The presets for the guitar amps are a selection of effects and amp settings that are supposed to be for the type of sound the preset suggests. You don't have to keep them the way they are. You can tweak all of the parameters.
For playing bass on your guitar, you can use the vocal transformer plugin (Female to male) to get a lower octave. Some folks have reported this is satisfactory for bass. I have not done it, myself, as I have a bass.
You cannot "move" notes you play on your guitar. You can only move notes on software instrument regions.

Similar Messages

Where can i find the most popular common effects and title template for free online?

where can i find the most popular common effects and title template for free online?

Hello,
I have a couple of links that I have used:
http://www.solarisinternals.com/wiki/index.php/ZFS_Best_Practices_Guide
http://www.solarisinternals.com/wiki/index.php/ZFS_for_Databases
These are not exactly new, so you may have encountered them already.
List of ZFS blogs follows:
http://www.opensolaris.org/os/community/zfs/blogs/
Again, there does not seem to be huge activity on the blogs featured there.
jason.
http://jarneil.wordpress.com

What is difference between additive delta and new status for change record

Hi Experts
Can any one explain me about the difference between additive delta and new status for change record with example
if any one has a document please post it iam thank full to u
thanks
Ahmed
Please search the forum before posting a thread
Edited by: Pravender on Feb 12, 2012 1:54 PM

Hi
Additive delta --- We will get the changed quantity.
say suppose you have sales order and quantity like 1111 30 which is loaded to cube(BW).
now same record qty has changed from 30 to 40. As we have additive delta, we will get new record as 1111 10.
new status for change record: This is same as like After image delta type in standard SAP data sources. for every change in record you should have new record.
say if you have any number which will be generated by system for new/changed record, then you can use this.
You can use this option when delta option set to "numeric pointer"
Regards,
Venkatesh

Year of Cash Effectivity and Due Date for payments in following year

Hi experts!
I have a problem with Year of Cash Effectivity when dealing with invoices which have Due Date in a different year from the posting date. I just need revenues and expenses to be recognized under the accrual basis of accounting (with the invoice, not with "cash effectivity" depending on terms of payment). But we do need "cash effectivity" for commitments budget and MM.
I am using Update Profile=000359, and have tried to "Override Update Profile" for Value Type=54 (Invoices) checking "Posting Date" for Payment/Commitment Budget, instead of "Due Date". I have also deactivated settings that have to do with payments transfer in <<Public Sector Management->Funds Management Government->Actual and Commitment Update/Integration->Integration>>.
Is there any way to change this without changing Update Profile?
Thanks for your help!
Iván Garcí

Hello Ivan
I believe this note will help you:
[Note 883122 - Spanish Public Sector: Specific functions (BAdIs and exits)|https://service.sap.com/sap/support/notes/883122]
see this paragraph
BAdI FMRI
The method FMRI_BADI_9 allows the customer to change, according
to their needs, the Year of Cash Effectivity in which FI
documents are updated in Funds Management.
The system performs some checks (for example the update profile
has to use the Year of Cash Effectivity) to permit the
modification of the Year of Cash Effectivity in this BADI. The
Year of Cash Effectivity determined in this BAdI cannot be
earlier than the one for the date when the Financial Accounting
payments are updated in Funds Management.For more detailed
information on this topic, consult the note 1129408.
hope this will help you!
Kind regards
Mar

DownloadOK,installingOK, rebooting has no effect and a request for it keeps reacurring, no way to open Firefox?

I've downloaded Firefox version 9.While running setup a request for rebooting was observed. After having finished the setup another reboot followed, thereafter an "Unpack" icon appeared in the taskbar. Upon pressing it I was requested to reboot again ... and again, and again... . The same request came up whether I push the "Unpack- icon" on the desk top, or start menu. I cannot find a way to finish the installation, nor to uninstall the newly obtained upgrade. Neither I was able to open any version of the Firefox application. Also all tries to installed ver. 9 over the existing (previous or newly upgraded) versions fail.
I am using Windows 7 Ultimate 64 bits with ample reserves of memory.

Found a working around to the problem. After updating from version 8.0.1, it keep bugging me to rebut, to no use what so ever. Here a solution I found:
1. To those in need to save their bookmarks, password saved, etc, you need first of all to save your profile folder, witch can be found on Windows 7 on the location
C:\Users\user name\AppData\Roaming\Mozilla\Firefox\Profiles
Copy the hole directory Profiles to what ever location to keep safe.
Those ho have no need to backup, skip this steep.
2. Manual delete the whole directories:
C:\Users\user name\AppData\Roaming\Mozilla
and
C:\Users\user name\AppData\Local\Mozilla
3. If still have links in Start Menu please delete them (mine has gone away when I try to update to 9 version)
4. Go to Control Panel / Programs and Features and click uninstall Mozilla Firefox, a small message will ask you if you want to remove the link because the program cant be found, click yes.
5. Download and install Firefox 9 from Mozilla.org using Internet Explorer or other browser of your choice (Chrome, Opera, etc)
6. In order to have your data back, copy the content of the Profile folder over the new installment, but be careful to copy only the content, because the name of the folder that literally contain the Profile data, is every time another, by example:
original mozilla 8 was 9um78jwe.default and the new one is skfwyddf.default
so copy only the content to another, meaning the directories
bookmarkbackups
chrome
extensions
icons
minidumps
weave
and off course all the other files.
When asked to overwriting say yes.
This is it, you can now start your new mozilla 9 installment.
Good luck.

After Effects and Premiere Pro for 32bit system

Does Adobe have a fix to allow installation of Premier Pro and After Effects on a 32bit system?

There is no "fix". AE and Premiere have been 64bit only since CS5. Sorry, but you're late to the party and better upgrade your operating system or the computer hardware in its entirety.
Mylenium

Are you using After Effects and are looking for plug-ins?

AV3software.com has all the plug-ing you are looking for, all centralized in one website all available via download at a very attractive price.
Check it out www.av3software.com

Hi Michael,
That's not really the right forum for that, Adobe as an extensive list of those plug-ins on their own web sites, here's the link:
http://www.adobe.com/products/plugins/aftereffects/main.html
Best,
PJ

I just downloaded after effects and opened it for the first time and i can't start a new project

everytime i click on the bar above the program to start a new project it crashes

Sorry to hear that. Perhaps you ought to provide some information for diagnostic purposes:
FAQ: What information should I provide when asking a question on this forum?

Guitar amp with 'classical guitar' sound

Hi,
I'm using the Fender Squier Strat usb to record with Logic Pro X. Guitar amps don't include an amp that would simulate 'classical guitar'. Is there? Anybody's advice would be helpful. I know there is a patch to play classical guitar via a keyboard. But I'm a classical guitar player who would like to use his USB Strat to record classical guitar stuff. Thanks in advance.

I think, tongue-in-cheek Pancentre is making a valid point that you're not going to get that 'classical' sound too easy you need a warm acoustic sound going in. However, let me explain:
Logic (In fact 99% of music software) can be expanded via plugins. On the Mac/OSX these are called Audio Units. 2 Of the big players for guitarists is Native Instruments (NI) Guitar Rig, and IK's Amplitude.
Guitar Rig is an all-in-one solution which can be used with a guitar pedal controller which controls the software. It's got tons of options, standard presets and loads more scattered around the internet. Anything from experimental, through to Jazz and Death metal you can get from that, it's very flexible.
Acoustic emulation/simulation is basically a series of effects and EQ's in Guitar Rig/Amplitube/Logic which will provide you with an acoustic/warm sound. Basically, it's job is to raise the low frequencies and remove the mids (At least that's how i have to process mine) and place a bit of delay/reverb on the high frequencies to create space. But you never will recreate that wonderful sound of a classic guitar 'pushing air' by plugging an electric in and running it through an acoustic simulator.
The characteristics, fret noises etc. Just won't be there.
If you're just wanting to have some fun, jam and make a few tracks for your own enjoyment they're still pretty good for that. But you will have to adjust some effects settings, purely as guitars, pickups, strings etc. can all cause the sound to differ. So don't think you can just get away with selecting a preset each time.
Personally, i think it's part of the enjoyment coming up with a sound which helps you play, and sounds 'right'. These plugins, and guitar simulators are so straight forward too, they've invested a lot of development into making them act like the real thing.

After Effects AND/OR Premiere Pro CS5 ?

Hi guys,
I am quite new, I have only done one videoproject and that was in Premiere Pro CS4. Now I got a new machine and have both Premiere Pro CS5 and After Effects. I have started learning AE from some videos and it is quite impressing what you can do there. So I hope I can use AE to improve my videos.
My question is, shall I do the project in PPCS5 and then connect to AE for making special effects on clips or shall I do the whole project in After Effects ?
If I choose AE for the project, will I miss some functions from Premiere Pro?
Many thanks in advance !
Sven

Thank you guys!
You put me on track, expecially with the link!
From beginning I am just taking care of old videos that noone look at because not edited so most of the time just crap.
I want to edit them, try to improve color and sharpness but also add some funny elements so they are more interesting to watch.
I have 30 videos from my daughter, each 1 hour and 8 of my own (really crap) and 8 VHS from a friend. That is just to start with.
Start Adobe Premiere Pro from within After Effects and capture footage for use in After Effects. (See Use Adobe Premiere Pro for capture (Production Premium and Master Collection only).)
Use Adobe Dynamic Link to work with After Effects compositions in Adobe Premiere Pro without first rendering them. A dynamically linked composition appears as a clip in Adobe Premiere Pro.
Use Adobe Dynamic Link to work with Adobe Premiere Pro sequences in After Effects without first rendering them. A dynamically linked sequence appears as a footage item in After Effects.
Start After Effects from within Premiere Pro and create a new composition with settings that match the settings of your Premiere Pro project.
Select a set of clips in Adobe Premiere Pro and convert them to a composition in After Effects. "
So with a testvideo I will start using these 5 different methods so I learn when to use which one!
And I also have 4-5 videolessons to watch.
Thanks again!
I probably be back soon with more questions!

Help! I only hear clean electric guitar while recording, and amp/effects after recording!

I have my electric guitar plugged into an Apogee Duet (driver is up to date with Yosemite). After track is setup with effects, in an audio track or in a guitar preset track (I tried both), I can play and hear the guitar clean tones only without the effects I have put on the track, even though I have chosen guitar effects, like amp, pedals, etc... Only after recording during playback, not pre, can i hear the effects I have chosen. Why is this? So pre recording and during recording, a clean tone. Play back the track, it's all there with the amp and sounds I have chosen. Frustrated.

Excuse this short reply, rehearsal in 30 minutes.
It sounds like you need to first turn off the Direct monitoring of the Interface. Most audio interfaces have a "direct no-latency" monitoring that actually takes place before the audio even goes to Logic, it's done within the interface. Different companies have different names for it, low-latency monitoring, direct monitoring....etc.
Next, open Logic's Preferences and I think with Logic-X it's under the General tab (everything I'm describing will be under the general or devices tabs).
Select Software monitoring, make sure you I/O buffer setting is at 128. Lower buffer settings mean less latency but use more CPU.

Excel, PowerView error in SharePoint 2013: "An error occurred while loading the model for the item or data source 'EntityDataSource'. Verify that the connection information is correct and that you have permissions to access the data source."

I've installed SQL Server 2012 SP1 + SP server 2012 + SSRS and PowerPivot add-in.
I also configured excel services correctly. Everything works fine but the powerview doesn't work!
While I open an excel workbook consist of a PowerView report an error occurs: "An error occurred while loading the model for the item or data source 'EntityDataSource'. Verify that the connection information is correct and that you have permissions
to access the data source."
error detail:
<detail><ErrorCode xmlns="http://www.microsoft.com/sql/reportingservices">rsCannotRetrieveModel</ErrorCode><HttpStatus xmlns="http://www.microsoft.com/sql/reportingservices">400</HttpStatus><Message xmlns="http://www.microsoft.com/sql/reportingservices">An
error occurred while loading the model for the item or data source 'EntityDataSource'. Verify that the connection information is correct and that you have permissions to access the data source.</Message><HelpLink xmlns="http://www.microsoft.com/sql/reportingservices">http://go.microsoft.com/fwlink/?LinkId=20476&EvtSrc=Microsoft.ReportingServices.Diagnostics.Utilities.ErrorStrings&EvtID=rsCannotRetrieveModel&ProdName=Microsoft%20SQL%20Server%20Reporting%20Services&ProdVer=11.0.3128.0</HelpLink><ProductName
xmlns="http://www.microsoft.com/sql/reportingservices">Microsoft SQL Server Reporting Services</ProductName><ProductVersion xmlns="http://www.microsoft.com/sql/reportingservices">11.0.3128.0</ProductVersion><ProductLocaleId
xmlns="http://www.microsoft.com/sql/reportingservices">127</ProductLocaleId><OperatingSystem xmlns="http://www.microsoft.com/sql/reportingservices">OsIndependent</OperatingSystem><CountryLocaleId xmlns="http://www.microsoft.com/sql/reportingservices">1033</CountryLocaleId><MoreInformation
xmlns="http://www.microsoft.com/sql/reportingservices"><Source>ReportingServicesLibrary</Source><Message msrs:ErrorCode="rsCannotRetrieveModel" msrs:HelpLink="http://go.microsoft.com/fwlink/?LinkId=20476&EvtSrc=Microsoft.ReportingServices.Diagnostics.Utilities.ErrorStrings&EvtID=rsCannotRetrieveModel&ProdName=Microsoft%20SQL%20Server%20Reporting%20Services&ProdVer=11.0.3128.0"
xmlns:msrs="http://www.microsoft.com/sql/reportingservices">An error occurred while loading the model for the item or data source 'EntityDataSource'. Verify that the connection information is correct and that you have permissions to access the
data source.</Message><MoreInformation><Source>Microsoft.ReportingServices.ProcessingCore</Source><Message msrs:ErrorCode="rsErrorOpeningConnection" msrs:HelpLink="http://go.microsoft.com/fwlink/?LinkId=20476&EvtSrc=Microsoft.ReportingServices.Diagnostics.Utilities.ErrorStrings&EvtID=rsErrorOpeningConnection&ProdName=Microsoft%20SQL%20Server%20Reporting%20Services&ProdVer=11.0.3128.0"
xmlns:msrs="http://www.microsoft.com/sql/reportingservices">Cannot create a connection to data source 'EntityDataSource'.</Message><MoreInformation><Source></Source><Message>For more information about this error navigate
to the report server on the local server machine, or enable remote errors</Message></MoreInformation></MoreInformation></MoreInformation><Warnings xmlns="http://www.microsoft.com/sql/reportingservices" /></detail>
Please help me to solve this issue. I don't know if uploading the excel workbook is enough or maybe It needed to connect to another data source.
I Appreciate in advance.

Hi Ali.y,
Based on the current error message, the error can be related to the
Claims to Windows Token Service (C2WTS) and is an expected error under certain conditions. To verify the issue, please check the aspects below:
     1. The C2WTS Windows service and C2WTS SharePoint service are both running.
     2. Check the SQL Server Browser service is running on the machine that has the PowerPivot instance of SSAS.
     3. Check the domain. You're signing into SharePoint with a user account in some domain (call it Domain A). When Domain A is equal to Domain B which SharePoint server itself is located (they're the same domain), or Domain
A trusts Domain B.
In addition, the error may be caused by Kerberos authentication issue due to missing SPN. In order to make the Kerberos authentication work, you need to configure the Analysis Services to run under a domain account, and register the SPNs for the Analysis
Services server.
To create the SPN for the Analysis Services server that is running under a domain account, run the following commands at a command prompt:
• Setspn.exe -S MSOLAPSvc.3/Fully_Qualified_domainName OLAP_Service_Startup_Account
Note: Fully_Qualified_domainName is a placeholder for the FQDN.
• Setspn.exe -S MSOLAPSvc.3/serverHostName OLAP_Service_Startup_Account
For more information, please see:
How to configure SQL Reporting Services 2012 in SharePoint Server 2010 / 2013 for Kerberos authentication
Regards,
Heidi Duan
Heidi Duan
TechNet Community Support

When I create a new track for Guitar it labels the track "Clean Combo" no matter which amp I select. Anyone else noticing this?

When I create a new track for Guitar it labels the track "Clean Combo" no matter which amp I select. Anyone else noticing this?

Look at it this way: there is no need to record that effect onto the audiofile. This is a great advantage of modern recording, and this is how most DAW's work by default. Just leave the plugin on when playing back.
Only for CPU management reasons it may be advantageous in certain situations to either freeze a track or bounce it in place (both techniques will render an audiofile that may include the effect). But in general it is a (very) good thing that it is possible to tweak any effect after recording, and have a clean, unprocessed recorded signal to work with. And if the effect was perfect at the time of recording, well, just leave the plugin(s) engaged.
http://help.apple.com/logicpro/mac/10.1/#/lgcp8ae5826e
http://help.apple.com/logicpro/mac/10.1/#/lgcpf1cbfd51
ps: there is a way to record plugin effected signal live into the audiofile, but it involves creating a custom environment setup.

MacBook Pro 13 inch (mid 2012) v MacBook Pro 15 inch (mid 2014) for After Effects and Premiere

Hi everyone,
I'm interested in working with After Effects CS6 and Premiere CS6 probably creating quite heavily layered files and experimenting with and combining effects. (I also work with Photoshop and Illustrator.)
My workplace allows me to use a 2.5 GHz Intel Dual Core i5 / MacBook Pro 13 inch (mid 2012, non retina) with hard disk and integrated graphics card (Intel HD Graphics 4000 512MB). I understand this Mac can be maxed out at 16GB of RAM. (Official Apple specs I realise say 8GB RAM is the max for this computer but I've looked into this thoroughly and have confirmed that 16GB is in fact possible.)
I'm considering purchasing one of the new Haswell based MacBook Pro (mid 2014) models for myself.
If I do, I'll get the retina 15 inch / Intel Quad Core i7 / 16GB RAM / Intel Iris Pro Graphics / NVIDIA GeForce GT 750M / 1TB Flash Storage.
I realise there is a big difference between these two machines in terms of their specs - the 15 inch with the dedicated GPU will be far more suited to motion graphics work than the lower spec machine with integrated graphics card.
Currently, my understanding is that After Effects CS6 and Premiere CS6 do not support the NVIDIA GeForce GT 750M but from research on the net I believe it's possible to add this video card to the list of supported cards within the respective applications, forcing them to recognise and use it.
Having read about the upcoming Broadwell chip, which I think may be capable of supporting 32GB RAM (possibly coming in Q2 2015 from the various websites I've visited) I wonder if it is worth holding off my purchase, and maxing out my older 13 inch laptop in order to run After Effects and Premiere for the time being.
If I waited for Broadwell based 15 inch MacBooks I think its likely they'll be expandable to 32GB RAM, making the computer a better long term investment.
eg if Adobe increase minimum/recommended memory requirements for their software in the next few years. While I don't know for sure this will happen, it does seem quite likely at some stage. The 2014 15 inch MacBook - while an excellent computer at the moment - could potentially be slightly limited with regard to future Adobe software releases as its max RAM is 16GB.
I realise I could potentially look at a high end iMac if memory is a concern, but I prefer the portability of a laptop so I'm restricting myself to portable options for the moment.
What I'm wondering is -
If I install the 13 inch 2.5GHz i5 laptop with 16GB RAM as is possible, how would it perform when running After Effects and Premiere? It currently has 4GB and it very quickly runs out of memory meaning playback of goes very slowly when previewing complex files in the timeline. This necessitates rendering of small test sections of the timeline to see it at the correct frame rate. Would the move from 4GB RAM to 16GB RAM give me a noticeable improvement in this regard? If so then this is tempting as I don't have to pay for it - I think my workplace will cover the cost of extra RAM. And then I can wait till next year to buy my own high end laptop.
The 15 inch 2.8GHz i7 quad processor has Iris Pro and dedicated NVIDIA GeForce GT750M with 2GB RAM. I would be paying the full cost myself.
I realise rendering would be faster with this Mac but would I see a noticeable improvement over the maxed out 13 inch laptop when previewing multi layered After Effects and Premiere compositions / sequences within the timeline? I like the idea of being able to preview footage in real time as I'm editing as it saves time and I think it makes the process easier generally.
Any thoughts welcome and thanks very much in advance for your time and advice.
Kind regards,
John

"It currently has 4GB and it very quickly runs out of memory meaning playback of goes very slowly when previewing complex files in the timeline."
"In this case yes, I can most certainly see a performance increase as your machine is still not too old and a RAM increase will help it for sure I just can't tell you by how much.
I own the same machine as yours (except for mine having 2.9ghz and i7, and 8GB of ram) so I think it's safe to say for me that the RAM increase will help you for sure."
That statement of mine answers your question you just asked

I have FCE 4.0.1 and running OS x 10.7.5 when i burn my movie the audio from my movie clips don't come through . My Sound effects and music can be heard. I export to Quicktime movie, make it self contained then open IDVD for an intro and burn it.

I have FCE 4.0.1 and running OS x 10.7.5 when i burn my movie the audio from my movie clips don't come through . My Sound effects and music can be heard. First I export to Quicktime movie, make it self contained then open IDVD for an intro and burn it. everything sounds great in preview but then ( once again)I lose my audio from my movie clips.

Try Mixing Down the audio before export.
This info may help;
https://discussions.apple.com/message/1060680?messageID=1060680&amp%3b#1060680
Also serch this forum for Mix Down you should find lots of info.
Al

Additional effects and amp models for guitar

Similar Messages

Maybe you are looking for