Adjust recording end time on a 6416 for a single show recording.

This may seem like a dumb question but I can't see how to set the stopping time of a recording to end say 30 minutes later.
I think I just received 1.6 last night, but I couldn't see how to do this in the previous release either.
In my defense, I normally use a TiVo for recording, but sometimes I have to use the Verizon 6416.
I was able to do this with an older release. 
I can see how to do it with a series recording, but not with a single show recording.

Got to DVR menu, select View Schedule, select the show in question and one of the options is something like change or recording options (not at my STB so not sure of the exact wording).  There is a place to modify the start / end times by preset increments.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

Similar Messages

  • Adjusting date and time does not work for pictures from one camera.

    I have a set of pictures taken with a Casio EX-Z20 camera in my Aperture 2 library. Because the clock of this camera was off by a few hours I changed them all at once with the option "Adjust date and time...". This worked well and when I sorted the images from different cameras by date in Aperture they were in the order.
    When exporting all the images as JPEG the images in the set from this camera was reset to it's original.
    That was very strange, I decided to try and change the date of these images in the master files as well by checking the checkbox "Also change master files".
    When I change the date from 15-10-2008 18:34:44 to 16-10-2008 10:34:44 (+16 hours) the date of the image changes to 16-10-08 01:36:43 GMT+02.00 (+9 hours, 1 minute, 59 seconds).
    When I change the date from 16-10-08 01:36:43 to 16-10-2008 19:36:43 (+18 hours) it ends up as being 16-10-08 10:38:42 (+9 hours, 1 minute, 59 seconds)
    When I change the date from 16-10-08 10:38:42 to 16-10-08 10:48:42 (+10 minutes) it ends up as 16-10-08 01:50:49 GMT+02:00 (-8 hours, 47 minutes, 7 seconds)
    I have worked around this problem by adding some hours to the desired time and eventually got it about right, but this is still a very annoying problem. Has anyone else encountered it or know of a way to avoid it?

    {quote:title=JohniBook wrote:}
    Has anyone else encountered it or know of a way to avoid it?
    {quote}
    I certainly have had issues regarding wrong dates, time stamping and DNG's in Aperture. There have been posts here from others as well with the same kind of date problems.
    I have reported the bug to Apple and hope for a solution to the issue in a near future.
    Regards
    Paul K

  • Adjusting Start / End Time on Apple TV

    Hello everyone,
    In iTunes, we have the ability to adjust the Start / End time of a song or video by right-clicking the media > Get Info > Options. Then when we playback the media the next time, it will use the settings to determine how far into the media it should start and stop. Is there any way for these settings to get passed through to the AppleTV?
    - Thanks

    I would also like an answer to this! The original Apple TV applied the custom Start and Stop times, however the new one ignores them and plays the whole video file! Very annoying! Any solutions out there?

  • Change End time of Recording in Progress?

    I know I can change the start and end time of a single show in the View Schedule menu, but this only works before the show has started recording.  Once the show has started recording, it disappears from the View Schedule menu.  Is there a way to adjust the end time of a single recording while it is being recorded?  For example, if I'm watching a game and it is running long and I want to add 60minutes to the end of the scheduled recording time.  How do I do this?

    Well, that's a bummer.  Love most things about FIOS, but the menu for the DVR really can be maddening.  Cox's was much more limited but also much more usable.  I wish Verizon would spend less time on widgets and more time on the UI of the DVR menu!!!
    Thanks for your reply!

  • If Time Recorder Enter Time Entry in SAP, Can It goes for approval on MSS ?

    Hi WF Experts,
    I would like to know, if  Time Recorder Enter Time Entry in SAP for group of employees, can it goes for approval on MSS for individual approval ?
    Would really appreciate your prompt response.
    Regards,
    Aashish

    Hi Experts,
    I got answer for it. I did it myself. It is possible.
    Thanks.
    Aashish

  • How do I get Calendar on Mac to stop auto correcting the end time?

    I input my work schedule into Calendar manually every week and I copy and paste one event to save some time. One annoyance I run into is when I'm altering the time from say, 10am-6pm, to 4pm-10pm. As soon as I switch the start time from am to pm, it automatically adjusts the end time to 10am on the following day. So then I have to go back and manually change it from an event spanning 2 days to an event that should only span 1 day.

    This works for me:
    To turn off Phone Calling on your iPad or iPod Touch, go to FaceTime under Settings and switch off iPhone Cellular Calls. On your Mac, open the FaceTime app, then go to Preferences under FaceTime, and tap Settings. From there, switch off the iPhone Cellular Calls option.
    Found it here:http://www.pocket-lint.com/news/131449-why-s-my-mac-taking-my-iphone-calls-how-t o-turn-off-apple-continuity
    I realise it doesn't quite solve the issue of FaceTime "knowing" whether the call has already been answered on another device, which I agree is a flaw. But in my case, I don't want to receive regular phone calls on my Mac at any time. Only the very rare FaceTime call. So turning off cellular calls is a solution of sorts.

  • Adding Validation In record working time.

    Hi Experts,
    I have to add a check in Record Working Time, so that, it does not allow to record working times which are more than 45 days older than today.
    Please tell me where I have to make changes, If I have to make changes in User Exit then please tell in which user exit and how.
    Regards
    Upendra Agrawal

    Upendra,
    check this link that tells about the available userexits for time.
    http://help.sap.com/saphelp_erp2005vp/helpdata/en/bd/53fa2fcc43594dbf9f406c18989a47/frameset.htm
    Mostly you need to write in CATS0003 (check the documentation)
    or else you can enhance HRXSS_WD_CAT_RECORD FM
    Thanks
    Bala Duvvuri

  • Rerecording Narration for a Single Slide

    I've recorded the narration for a long slideshow (without Keynote) and I need to rerecord the narration for a single slide. When I read the help files, they read as though I will wipe out everything after the slide I record. Please tell me that's not true and that there is a way I can record new narration for a single slide. Thanks.

    The term "narration" has a very specific meaning in Keynote: it refers to a spoken (usually) track that accompanies an entire slideshow, running through all of the slide changes.
    If you want to record a "voice-over" (VO) track for a single slide all you need to do is record this off-line (for example in Garage Band or any other audio production application) and then import this as an audio file into the individual slide. Use the Inspector > Build-in > start audio to initiate playback within the slide.
    Caveats: 1) This will play only while the specific slide is on the screen. IF you change the slide, the VO track will stop. 2) It will play simultaneously with any Soundtrack or Narration tracks you have assigned to the overall slideshow, and you have no way to control the relative balance between them. So, if you do have either (or both) a Soundtrack and Narration for your program, you will need to record these such that they leave room (either by fading out/in or reducing level) for this specific VO track.
    Good luck.

  • 39L4363D - Unable to set padding time for recording start and end time

    Hello,
    I have a problem with my 39L4363DG tv (Software 7.1.90.34.01.1).
    I'm not able the set padding time for recording start and/or end time as described in the [manual|http://www.toshiba-om.net/LCD/PDF/English/L4363-323950-English.pdf] on page 51. Both menu item "start padding time" and "end padding time" are disabled?
    Can anyone help me and give me an advice on how to solve it?

    Hi
    The padding time can be set for programmed recording.
    There is also an scheduling priority
    If scheduled time slots are next to each other and there is more than one minute between the end time of the first schedule and the start time of the next schedule, programmed recording will be performed correctly.
    When +Start Padding Time+ and +End Padding Time+ are set, the start time and end time will be the time plus the additional minutes.
    If scheduling times overlap, priority will be given to the programmed recording which starts first.
    When the programmed recording that started first ends, recording will switch to the next scheduled programme.
    At this time, depending on how far the scheduling times overlap, the beginning section of the next scheduled programme may not be recorded.

  • How to change colors for record working time calendar

    Hi,
    I would like to change the colors in the calendar displayed in record working time based on some conditions.
    How do i do that is there any BADI associated with that
    Thanks
    Bala Duvvuri

    Hi Bala ,
    Yes its possible to change that .
    You need to implement BADI for this ..
    BADI name : "PT_ABS_REQ"
    In the BADI "PT_ABS_REQ"   interface "IF_EX_PT_ABS_REQ" you can find the method
    "SET_CALENDAR_COLOR" in that you can set the colure for the Absent type ......
    Adjust Colors of Calendar and Team Calendar
    Functionality
    You can use this method to change the colors in the team calendar.
    In the standard system, the different statuses for requests have different colors. You can use this method to differentiate the colors of requests depending on the following aspects:
    Status of requests (status)
    Action that an employee has executed: new request, delete, change (UIA operation)
    Subtype of absence (SUBTY)
    Full-day or partial-day absence (BEGMT, where BEGMT = 0 signifies a full-day absence)
    Application mode ( mode). You specify the application mode in the Select Employees for the Team Calendar IMG activity.
    Color Display of Status of Leave Requests(COLORS_ACTIVE). You specify this status in the Specify How Leave Is Displayed and Default Values IMG activity.
    Available Colors
    You have a choice of 16 colors. The 16 colors are hard coded, that is, you cannot change them or add other ones.
    The available colors are stored with their RGB value as constants of the CL_PT_REQ_CONST class. Use these constants if you want to change the colors.
    Notes
    If you change the colors in the team calendar, you should also adapt the legend accordingly. You can use the Adjust Legend for Calendar and Team Calendar method to do so.
    Hope this work!!!

  • DB Adapter: Polling For New Records returns the First record multiple Times

    I Polling for New or Chnaged Records against DB2 on iSeries. The DB Adapter returns the first record from the Table multiple Times. If the Table has 5 records it displays the first record 5 times. I am using BPEL 10.1.3.1 Can anyone help me with this.

    Hi there,
    please check out the DBAdapter trouble-shooting guide:
    http://download-east.oracle.com/docs/cd/B31017_01/integrate.1013/b28994/app_trblshoot.htm#CIHFEHFA
    I am copying an entry from there into here:
    A.1.21 Some Queried Rows Appear Twice or Not at All in the Query Result
    Problem
    When you execute a query, you may get the correct number of rows, but some rows appear multiple times and others do not appear at all.
    This behavior is typically because the primary key is configured incorrectly. If the database adapter reads two different rows that it thinks are the same (for example, the same primary key), then it writes both rows into the same instance and the first row's values are overwritten by the second row's values.
    Solution
    Open Application Sources > TopLink > TopLink Mappings. In the Structure window, double-click PHONES. On the first page, you should see Primary Keys. Make sure that the correct columns are selected to make a unique constraint.
    Save and then edit the database partner link.
    Click Next to the end, and then click Finish and Close.
    Open your toplink_mappings.xml file. For the PHONES descriptor, you should see something like this:
    <primary-key-fields>
    <field>PHONES.ID1</field>
    <field>PHONES.ID2</field>
    </primary-key-fields>
    Thanks
    Steve

  • Setting a specific time zone for start/end times?

    I tend to travel in clusters, and was frustrated on this current trip when all of my flight times were adjusted by 3 hours on my iPhone and iPad after landing in Florida from California.  But they weren't "corrected" to the appropriate local times on any of the flights... which, of course, means that all of my alerts are at the wrong time!
    Is there a way to specify which time zone an event occurs in?  i.e., start time is PST, end time is EST
    (I can see how to turn off automatic time zone changes, but that won't help me until I get home)
    Thanks!
    Chris

    In Mac OS X Lion, it's iCal > Preferences > Advanced > check Turn on Timezone Support
    In iOS 5, it's Settings > Mail, Contacts, Calendars > TIme Zone Support > on
    The start and end time are in the same zone (and that's the zone associated with the event), but iCal automatically adjusts the entry to local time in the daily and related views.  There isn't a way to have a unique timezone for the start- and the end-time in a single event.

  • Master_detail for more than one record at a time

    Hi,
    How can i display master_detail records for more than one records at a time, for example, i have two tables A and B , A has username and role and B has username and profile. here i wanted to display 10 users at a time on my 6i form with username, role and profile.
    i have created a master-detail relation ship with these tables when i'm executing F8 on blcok A , it displays 10 records on BlockA but, only one at a time on block B, how can i display all corresponding records on block B at a time.
    Thanks for your help.Bcj

    Thanks Roberts, that was realy informative due to some doubts i would like to confirm my requirements , i have two blocks A and B and each master record has only one detail record. but i wanted to display at least 10 master_detail relationships(records) on the form at a time, i would like to know is it possible to do without creating any table or view for example,
    data in table A,
    username role
    AAA R1
    BBB R2
    CCC R3
    data in table B,
    username profile
    AAA P1
    BBB P2
    CCC P3
    i wanted to display it on form like below,
    username role profile
    AAA R1 P1
    BBB R2 P2
    CCC R3 P3
    Also would like to know that how can i select data from dba_users, any restriction is there on forms 6i, i can select it on sqlplus.
    Thanks Again, Bcj

  • Is there a way to enter an event time in Calendar as a reminder for me and NOT have Calendar erase it in the info as it reads it into the event start and end times?

    Calendar can recognize and derive event start and end times from the text description entered.  However, when it seizes on a time (start and/or end) and automatically enters it as the start and/or end time, it also (sigh) deletes the time from the text.  I enter the times as reminders for me, how can one prevent them from being deleted by Calendar??

    I am having the same darn problem. I really dislike this auto feature in Calendar.
    Can anyone help us please?

  • How to record a time-limited video with Adobe AIR for iOS

    I am trying to record a time-limited video with Adobe AIR for iOS.
    For example, I want to implement the following function. Start a one-minute timer before launching CameraUI to record video. When the timeout event happens after one minute, stop recording video, close the CameraUI view and obtain the video data so far.
      I have several questions related to that.
      1. How to stop recording video from outside the CameraUI view(in this case, from the timeout event handler) and then close the CemeraUI view? As far as I know, to close the CameraUI view, the only way is to press the [Use Video] button or the [Cancel] button from inside the CameraUI view. Is it possible to close it from outside?
      2. Even if the first problem mentioned above is solved, then how can I get the video data so far(in this case, the video data before the timeout). I know that normally we can get a MediaPromise object from MediaEvent parameter of the  complete handler, and read the video data from the MediaPromise object. But obviously in this case, we can not access the MediaPromise object just because the complete handler itself will not be executed since the [Use Video] button is not pressed.
      3. Is it possible to add a stopwatch to show possible remaining recording time when CameraUI view is open? It seems that the CameraUI automatically uses the full screen of iOS device(in my case, iPad) and there is no extra space to show the stopwatch.
      Are there any solutions or workarounds about the three problem above? I really appreciate it if anyone has any idea about this. Thanks in advance.

    You'd have more control by using the Camera object, showing the camera on a video object inside a Sprite, and capturing that. Then you could put whatever graphics alongside it on the stage.. I've used FlashyWrappers in a test to capture the video to the library.  It took some work, but the test worked well...
    Flash/AIR record videos of your apps and games: Rainbow Creatures

Maybe you are looking for