ADM(Anomaly Dectector Module) PowerDown Failure in upgrade process.

hellow, everyone.
i'm yunchouljung in korea
i have a question about ADM module power down issue.
i had upgraded AGM Module successfully in version 6.1.2 to 6.1.6
but failed ADM Module upgrade in version 6.1.2 to 6.1.6
i uploaded a AP images in MP status and enterd "hw-module module 12 reset cf:4" command.
(i waited a message "you can now reset the module....")
after a reset process, ADM module disabled by SCP dnld Failure.
so, i enabled a power on ADM Module but result is same.
my upgrade process is below.
1.     hw-module module 12 reset cf:1
2.     copy ftp://[email protected]/c6svc-adm1G-k9.6-1-6.bin pclc#12-fs:
3.     hw-module module 12 reset cf:4
anybody help me?
thanks in advance.
p.s : i have already tested other ios version and ap/mp images.
================================================================
the module version and log is below.
Router_OUT#sh module
Mod Ports Card Type                              Model              Serial No.
2    3 Anomaly Guard Module                   WS-SVC-AGM-1-K9
3   16 16 port 1000mb GBIC ethernet           WS-X6416-GBIC
5   48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX
7    2 Supervisor Engine 720 (Active)         WS-SUP720-3B
9    4 CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE
10    8 Network Analysis Module                WS-SVC-NAM-2
12    3 Anomaly Detector Module                WS-SVC-ADM-1-K9
Mod MAC addresses                       Hw    Fw           Sw           Status
2 0017.e067.ec6c to 0017.e067.ec73   2.0   7.2(1)       6.1(6)       Ok
3 000e.d73c.3d40 to 000e.d73c.3d4f   2.5   5.4(2)       8.5(0.46)RFW Ok
5 0015.2bfe.c130 to 0015.2bfe.c15f 10.1   7.2(1)       8.5(0.46)RFW Ok
7 0016.c85e.3aa0 to 0016.c85e.3aa3   5.2   8.4(2)       12.2(18)SXF1 Ok
9 001b.d45d.f890 to 001b.d45d.f893   2.6   12.2(14r)S5 12.2(18)SXF1 Ok
10 0003.fead.7592 to 0003.fead.7599   2.0   7.2(1)       4.0(1)       Ok
12 0012.80f1.1ae8 to 0012.80f1.1aef   1.0   7.2(1)       8.5(0.46)RFW PwrDown
Mod Sub-Module                  Model              Serial       Hw     Status
7 Policy Feature Card 3       WS-F6K-PFC3B       SAL10478K1R 2.3    Ok
7 MSFC3 Daughterboard         WS-SUP720          SAL104892TJ 2.5    Ok
9 Centralized Forwarding Card WS-F6700-CFC       SAL1124QX44 3.1    Ok
Mod Online Diag Status
2 Pass
3 Pass
5 Pass
7 Pass
9 Pass
10 Pass
12 Not Applicable
Router_OUT#
47w1d: SP: The PC in slot 2 is shutting down. Please wait ...
47w1d: SP: shutdown_pc_process:No response from module 2
Jul 13 16:54:49: %C6KPWR-SP-4-DISABLED: power to module in slot 2 set off (Reset)
47w1d: SP: OS_BOOT_STATUS(2) MP OS Boot Status: finished booting
Jul 13 16:56:50: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimal Diagnostics...
Jul 13 16:56:57: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been disabled.
Jul 13 16:56:57: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics
Jul 13 16:56:57: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are now online
Jul 13 16:56:58: %SVCLC-5-FWTRUNK: Firewalled VLANs configured on trunks
Jul 13 17:32:23: %SVCLC-SP-5-STRRECVD: mod 2: <Application upgrade has started>
Jul 13 17:32:23: %SVCLC-SP-5-STRRECVD: mod 2: <Do not reset the module till upgrade completes!!>
Jul 13 17:42:11: %SVCLC-SP-5-STRRECVD: mod 2: <Application upgrade has succeeded>
Jul 13 17:42:11: %SVCLC-SP-5-STRRECVD: mod 2: <You can now reset the module>
47w1d: SP: The PC in slot 2 is shutting down. Please wait ...
47w1d: SP: PC shutdown completed for module 2
Jul 13 17:42:57: %C6KPWR-SP-4-DISABLED: power to module in slot 2 set off (Reset)
47w1d: SP: OS_BOOT_STATUS(2) Anomaly Guard OS Boot Status: finished booting
Jul 13 17:45:03: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimal Diagnostics...
Jul 13 17:45:06: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been disabled.
Jul 13 17:45:06: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics
Jul 13 17:45:06: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are now online
Jul 13 17:45:07: %SVCLC-5-FWTRUNK: Firewalled VLANs configured on trunks
47w1d: SP: The PC in slot 12 is shutting down. Please wait ...
47w1d: SP: shutdown_pc_process:No response from module 12
Jul 13 17:53:29: %C6KPWR-SP-4-DISABLED: power to module in slot 12 set off (Reset)
47w1d: SP: OS_BOOT_STATUS(12) MP OS Boot Status: finished booting
Jul 13 17:55:30: %DIAG-SP-6-RUN_MINIMUM: Module 12: Running Minimal Diagnostics...
Jul 13 17:55:37: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been disabled.
Jul 13 17:55:36: %DIAG-SP-6-DIAG_OK: Module 12: Passed Online Diagnostics
Jul 13 17:55:37: %OIR-SP-6-INSCARD: Card inserted in slot 12, interfaces are now online
Jul 13 18:26:27: %SVCLC-SP-5-STRRECVD: mod 12: <Application upgrade has started>
Jul 13 18:26:27: %SVCLC-SP-5-STRRECVD: mod 12: <Do not reset the module till upgrade completes!!>
Jul 13 18:37:05: %SVCLC-SP-5-STRRECVD: mod 12: <Application upgrade has succeeded>
Jul 13 18:37:05: %SVCLC-SP-5-STRRECVD: mod 12: <You can now reset the module>
47w1d: SP: The PC in slot 12 is shutting down. Please wait ...
47w1d: SP: PC shutdown completed for module 12
Jul 13 18:38:35: %C6KPWR-SP-4-DISABLED: power to module in slot 12 set off (Reset)
Jul 13 18:46:04: %C6KPWR-SP-4-DISABLED: power to module in slot 12 set off (Module Failed SCP dnld)
Jul 13 18:53:54: %OIR-SP-6-REMCARD: Card removed from slot 12, interfaces disabled
Jul 13 19:01:28: %C6KPWR-SP-4-DISABLED: power to module in slot 12 set off (Module Failed SCP dnld)

> *** ERROR => ThInit: db_connect (step 1, th_errno
> 13, action 3, level 1) [thxxhead.c 10156]
Is your database running (mounted and open)?
Markus

Similar Messages

[SOLVED]X start failure after upgrade: dri3,present modules missing

I start X with ~.xinitrc from console, which won"t work after last upgrade --first in two weeks.
(EE) Server terminated with error (1).Closing log file.
xinit: giving up
xinit: unable to connect to X server: Connection refused
xinit: server error
Xorg.log.0 :
[51:778] (EE) intel: Failed to load module "dri3" (module does not exist, 0)
[51:779] (EE) intel: Failed to load module "present" (module does not exist, 0)
Installed packages (EDIT: completed):
xf86-video-intel-2.99.{914-4,916-1}-i686 and also tried with xf86-video-intel-git, with "SNA" acceleration.
intel-dri 10-2.7-3
dri2proto 2.8-2
dri3proto 1.0-1
xf86driproto 2.1.1-3
Linux 3.15.5-2-ARCH i686
Linux CK Atom 3.16.2-1
Issue occurred after upgrading from v2.99.912-1 to v2.99.914+. I was going to try downgrade xf86-video-intel to v2.99.912-1 (as in the first thread in Refs) but went in a dependency conflict, with the older intel driver requiring glamor-egl which conflicts with xorg-server ':-|
Atom netbook
lspci:
00:02.0 VGA compatible controller: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller
Some refs :
» [SOLVED] X start failure after upgrade https://bbs.archlinux.org/viewtopic.php?pid=1426837
» [Solved] xf86-video-Intel-2.99.912-1 breaks xorg https://bbs.archlinux.org/viewtopic.php?id=182932
Last edited by kozaki (2014-09-12 09:45:53)

The issue occurred after upgrading from xf86-video-intel-v2.99.912-1 to v2.99.914+ and xorg-server-1.15.2-1 to 1.16.0-6 (and -devel).
same issue if:
- Switching accelaration method to "UXA" as per https://bugs.archlinux.org/task/40860
- Adding Option "DRI" "False"
Digged a bit:
- same modules errors but appears to be a Gnome bug (X starts): https://bbs.archlinux.org/viewtopic.php?pid=1441716
- same modules errors but X starts up without problems http://www.linuxquestions.org/questions … 175511372/
makes me doubt if this issue is related to the modules not found. Which is the single indication I found so far x-/
Any light on where can the issue comes from? hardware is pretty much standard even if getting a bit old. Never had Xorg related issue so far on this pancake.
Last edited by kozaki (2014-09-11 11:05:42)

Has anybody experience with "Cisco Anomaly Guard Module"

Hello,
had anybody experience with "Cisco Anomaly Guard Module" WS-SVC-AGM-1-K9 for Catalyst 6500?
We're looking for some IDS/IPS prevention system which could take 2-3 Gbits of traffic. From the documentation it looks not bad, and we can get them as used parts (6500 + Sup720 + AGM +ADM) quite cheap. The second solution is Arbor with cisco12000 as boader router (10Gbit uplink) is much more expencevie.
Arbor tries of cause sell us their solution as "Cisco Anomaly Guard Module" is ot of sale and doesn't have any new features, but from the Data sheets Cisco AGM is eactly what we need.
Or may be is there another solution which could be comparable to those two?
Thank you.

Hello padatta,
AGM/ADM are IDS/IPS systems, one can of couse discuss about the terms, but it won't be productive :).
IDSM2 has not enough performance and it should sit inline, ADM/AGM can change he next hop for the diverted traffic and be out of traffic path during the normal operation.
Konstantin

Anomaly Guard Module Configuration

I have an 1Gbps AGM and I am configuring Anomaly Guard Module. For testing purpose, I am trying to bypass/route the traffic through AGM, but I could not. The configuration is as mentioned below. I have captured the traffic using packet-dump and I could understand that traffic is forwarded to AGM, but not leaving AGM.
Can you please advice, what is missing in this configuration to enable all traffic to pass through AGM.
Configuration:
6509 Config:
firewall multiple-vlan-interfaces
firewall module 2 vlan-group 161
firewall vlan-group 161 2,10,62
anomaly-guard module 8 port 1 allowed-vlan 2
anomaly-guard module 8 port 2 allowed-vlan 61,62
anomaly-guard module 8 port 1 native-vlan 2
vlan 2-3,10-12,20,50-51,61-62
end
AGM Config:
diversion hijacking receive-via-ip 172.17.61.16
diversion hijacking receive-via-vlan 61
diversion injection 172.18.10.0 255.255.255.0 nexthop 172.17.66.1
interface eth1
ip address 172.18.2.11 255.255.255.0
mtu 1500
no shutdown
exit
interface giga2
mtu 1500
proxy 172.17.61.15
no shutdown
exit
interface giga2.61
ip address 172.17.61.16 255.255.255.0
mtu 1500
no shutdown
exit
interface giga2.62
ip address 172.17.66.15 255.255.255.0
mtu 1500
no shutdown
exit
ip route 192.168.100.0 255.255.255.0 172.17.61.1 giga2.61
ip route 172.18.10.0 255.255.255.0 172.17.66.1 giga2.62
default-gateway 172.17.61.1
zone CUSTOMER GUARD_DEFAULT
ip address 172.18.10.0 255.255.255.0
no bypass-filter *
bypass-filter 10 * * * no-fragments
bypass-filter 11 172.17.61.1 * * no-fragments
bypass-filter 12 192.168.100.1 * * no-fragments
end

The Guard module can operate at two different bandwidth performance levels: 1 Gigabit per second (Gbps) or 3 Gbps. The software image that you load on the Guard module determines the operating bandwidth by controlling the three physical interfaces between the module and the supervisor engine.

Impact of Function Modules when used in upgraded versions

Hello Experts,
I wan to know the Impact of Function Modules when used in upgraded versions. How the function module works irrespective of changes done to it in the latest verisons
Thanks in Advance

Hi,
If the function modules is released, it should not have any impact. However if not released, use them with caution as SAP does not support non-released function modules.
Cheers.
...Reward if useful.

[SOLVED] "Loading Modules" Slow after Latest Upgrade (EeePC 901)

After the latest upgrade, my EeePC is taking an incredibly long time (20+ seconds) at the "Loading Modules" stage of the boot process. I cannot find any error messages, and after the pause, the machine boots normally. This process used to be almost instantantaneous before the upgrade. The modules being loaded are rfkill and eeepc_laptop.
Can anyone help?
Thanks in advance
Last edited by myrlin (2011-06-27 10:28:21)

Hi Jason, thank you for helping me.
Here is my rc.conf:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
# startup and during the boot process. If set to 'no', the C locale is used.
# HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
# in the hardware clock being left untouched (useful for virtualization)
# Note: Using "localtime" is discouraged.
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
# VERBOSE: Verbose level (from 1 to 8). man 3 syslog for level info
LOCALE="en_GB.UTF-8"
DAEMON_LOCALE="no"
HARDWARECLOCK="UTC"
TIMEZONE="Europe/London"
KEYMAP="uk"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
VERBOSE="3"
# HARDWARE
# MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
# Replace every !module by an entry as on the following line in a file in
# /etc/modprobe.d:
# blacklist module
# See "man modprobe.conf" for details.
MOD_AUTOLOAD="yes"
MODULES=(rfkill eeepc_laptop)
# Udev settle timeout (default to 30)
UDEV_TIMEOUT=30
# Scan for FakeRAID (dmraid) Volumes at startup
USEDMRAID="no"
# Scan for BTRFS volumes at startup
USEBTRFS="no"
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="eeepc"
# Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
# Wired network setup
# - interface: name of device (required)
# - address: IP address (leave blank for DHCP)
# - netmask: subnet mask (ignored for DHCP)
# - gateway: default route (ignored for DHCP)
# Static IP example
# interface=eth0
# address=192.168.0.2
# netmask=255.255.255.0
# gateway=192.168.0.1
# DHCP example
# interface=eth0
# address=
# netmask=
# gateway=
interface=eth0
address=
netmask=
gateway=
# Setting this to "yes" will skip network shutdown.
# This is required if your root device is on NFS.
NETWORK_PERSIST="no"
# Enable these netcfg profiles at boot-up. These are useful if you happen to
# need more advanced network features than the simple network service
# supports, such as multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
# If something other takes care of your hardware clock (ntpd, dual-boot...)
# you should disable 'hwclock' here.
DAEMONS=(syslog-ng dbus hal networkmanager privoxy netfs rfkill eeepc_laptop @ufw @crond @alsa !bluetooth @samba @cups)
Here is my blacklist.conf (I have restored the framebuffer one):
blacklist rt2800pci
blacklist rt61pci
blacklist rt2x00pci
blacklist rt2800usb
blacklist rt2800lib
blacklist rt2x00usb
blacklist rt2x00lib
And here is the output of lsmod:
Module Size Used by
fuse 58669 3
ipt_REJECT 2029 1
ipt_LOG 6518 5
xt_multiport 1498 2
xt_limit 1423 7
xt_tcpudp 1883 7
xt_addrtype 2393 4
nf_conntrack_ipv4 9601 7
nf_defrag_ipv4 1023 1 nf_conntrack_ipv4
xt_state 971 7
ip6table_filter 1072 1
ip6_tables 10461 1 ip6table_filter
ipv6 249260 12
nf_conntrack_netbios_ns 801 0
nf_conntrack_broadcast 961 1 nf_conntrack_netbios_ns
nf_conntrack_pptp 3857 0
nf_conntrack_proto_gre 3241 1 nf_conntrack_pptp
nf_conntrack 50208 6 nf_conntrack_ipv4,xt_state,nf_conntrack_netbios_ns,nf_conntrack_broadcast,nf_conntrack_pptp,nf_conntrack_proto_gre
iptable_filter 1100 1
ip_tables 9186 1 iptable_filter
x_tables 11774 11 ipt_REJECT,ipt_LOG,xt_multiport,xt_limit,xt_tcpudp,xt_addrtype,xt_state,ip6table_filter,ip6_tables,iptable_filter,ip_tables
btusb 9897 0
bluetooth 115465 1 btusb
uvcvideo 55020 0
videodev 70734 1 uvcvideo
media 8545 1 videodev
joydev 7535 0
snd_hda_codec_realtek 225687 1
i915 557262 2
snd_hda_intel 19261 1
snd_hda_codec 66793 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 4919 1 snd_hda_codec
drm_kms_helper 24245 1 i915
snd_pcm 60311 2 snd_hda_intel,snd_hda_codec
drm 147653 3 i915,drm_kms_helper
uhci_hcd 19344 0
snd_timer 15542 1 snd_pcm
ehci_hcd 34847 0
rt2860sta 479236 1
intel_agp 8664 1 i915
psmouse 55927 0
snd 43527 8 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
usbcore 119004 5 btusb,uvcvideo,uhci_hcd,ehci_hcd
i2c_algo_bit 4431 1 i915
iTCO_wdt 10333 0
i2c_i801 7039 0
serio_raw 3430 0
pcspkr 1415 0
sg 21022 0
i2c_core 16665 6 videodev,i915,drm_kms_helper,drm,i2c_algo_bit,i2c_i801
evdev 7310 15
intel_gtt 11417 3 i915,intel_agp
crc_ccitt 1103 1 rt2860sta
iTCO_vendor_support 1553 1 iTCO_wdt
soundcore 5018 1 snd
battery 8905 0
processor 21884 0
eeepc_laptop 12452 0
atl1e 24804 0
button 3654 1 i915
sparse_keymap 2636 1 eeepc_laptop
thermal 6603 0
ac 2545 0
video 9852 1 i915
snd_page_alloc 5909 2 snd_hda_intel,snd_pcm
pci_hotplug 21978 1 eeepc_laptop
agpgart 22160 3 drm,intel_agp,intel_gtt
rfkill 12510 2 bluetooth,eeepc_laptop
ext4 334626 3
mbcache 4321 1 ext4
jbd2 59098 1 ext4
crc16 1077 2 bluetooth,ext4
sd_mod 25515 5
ata_piix 18569 3
pata_acpi 2396 0
libata 154349 2 ata_piix,pata_acpi
scsi_mod 110670 3 sg,sd_mod,libata
I hope this all means more to you than it does to me!!!!

Hello my OS upgrade process was interrupted due to Internet failure, how may I re-try to upgrade it? I got a message that says I can´t, the serial number can be used only once!

Hello I bought a macbook pro on August this year and got a bonus to upgrade the OS from Lion to Mountain Lion for free. I started the donwload but it was interrupted due to internet failure so the upgrade process was aborted. When I tried to initiated the process again, I got a message that says I can not used the same serial number to download Maountain Lion. What can do in order to upgrade the OS using the "bonus" I received with the purchase?

I have the same problem, only Purchases in the App Store shows nothing. The download NEVER showed up in the App Store only in the Launchpad with a progress icon. The Icon said paused but when clicked, it just disappeared with no download.
How am I supposed to get my free upgrade now?

Crypto failure when upgrading Windows 8.1 Pro install to Windows 10 Tech Preview 10041

Has anybody experienced the following error when trying to upgrade a Windows 8.1 Pro install to Windows 10 Tech Preview 10041
crypto_self_test_failed
The system reboots twice both times with the same error and then reverts back to Windows 8.1 Pro. This occurs during the upgrade process. Windows 10 never installs.
Thoughts? Suggestions?
Thanks
Eric Sten

Hi Eric,
It seems to be the upgrade self-test fails.
For testing Windows 10, you may consider take use of Hyper-V and install a VM of Windows 10:
Step-By-Step: Creating and Running A Windows 10 VM on Windows 8.1
Or try a dual boot:
How to Dual Boot Between Windows 7 (or Windows 8.1) and Windows 10 Technical
Preview (VHDX)
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

IDSM-2 upgrade process questions.

Hello,
I started a new job and have been tasked with looking into what we can do with the IDSM-2 module we have in our 6509. The company has not been using the module so it hasn't been updating in a few years. I do not have a current license so I know I cannot install new signature updates, but what I would like to do is upgrade the software to version 7.0(5a)E4. Once I have it upgraded I would like to configure it in our environment and then see about getting a signature license.
I have a few questions regarding the upgrade process, and could use some assistance.
First the IDSM is currently running version 5.1(3)S256.0. From what I have read I don't believe I can go directly to 7.0(5a)E4 so my Planned Upgrade Path is: 5.1(3)S256.0 -> 5.1(8)E3 -> 7.0(5a)E4.
Am I able to upgrade this way or is there another recommended way that I should do this upgrade?
The files I have for this are below, will they be enough or am I missing any?
Do I apply them in the order listed?
Can I apply all of these files from the IDM GUI?
IPS-K9-5.1-8-E3.pkg
IPS-engine-E3-req-5.1-8.pkg <--- Is this included in the above file?
IPS-K9-r-1.1-a-5.1-8-E3.pkg
IPS-K9-7.0-5a-E4.pkg
IPS-K9-r-1.1-a-7.0-5a-E4.pkg
I plan on backing up my configuration first just in case, but should this process have any affect on the configuration?
I also saw that the upgrade will convert the configuration, so should I back it up a second time between the 5.1(8)E3 and 7.0(5a)E4 step?
Will there be any effect on network traffic or downtime during this process?
Is there any thing else I need to be aware of or that I'm missing?
Thanks in advance,
Will

Hi Will. Since you indicated that this sensor has not been in-use, it would be quickest/easiest to simply re-image it directly to the desired version (7.0(5a)E4). Additional benefits of doing this are that the sensor's filesystem will be created clean, OS/binaries cleanly installed, no potential config conversion issues, etc.
Step-by-step instructions for doing this can be found here.
And, the System Recovery Image file you will need ('IPS-IDSM2-K9-sys-1.1-a-7.0-5a-E4.bin.gz') can be downloaded here.
Will there be any effect on network traffic or downtime during this process?
That depends on whether the sensor is configured in Promiscuous Mode or Inline [VLAN Pair] Mode. You can determine this from the Catalyst config. If the sensor is installed in Inline [VLAN Pair] Mode, then certainly the re-image (and even just upgrade) could be traffic-impacting (if there is no alternative/backup path for traffic to take), as in both scenarios, the sensor is rebooted and not available for ~10 minutes (during which time, it would not be forwarding traffic (if it were installed Inline)). Additionally, since re-imaging results in a clean/default config, if the sensor were configured Inline, that portion of the config would have to be re-input post-reimage so that the sensor would know to forward traffic accordingly again. Details about the modes can be found here.

Cisco Modem Firmware (HWIC) upgrade Process

HI experts,
I need to upgrade firmware of my LTE ( Hwic) module for the router 2901. I am wondering if this is the part of IOS upgrade process , I mean ones I upgrade IOS to the latest version will it upgrade my modem firmware by own or I need to upgrade LTE modem separately?
can you guys please share your experience here?
any docs on this please?
Thanks!

Hi,
The LTE module is part of main Cisco IOS you load into the router. Once you upgrade the IOS, it also applies to the module.
ntegrated 4G LTE WWAN broadband: With the 4G LTE WWAN modem integrated into the router, you gain the benefits of simplified installation and management. In addition, the Cisco 4G LTE WWAN EHWICs are tightly integrated with Cisco ISRs, which run the industry-leading Cisco IOS® Software, giving access to all the advanced features of Cisco IOS Software such as quality of service (QoS), intelligent network queuing, and robust security.
Link:
http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/4g-lte-wireless-wan-enhanced-high-speed-wan-interface-card/datasheet_c78-710314.html
HTH

DMM 5.3 upgrade process failing

We are running the Digital Media Manager version 5.2.3 on a UCS-C210.
I have attempted to upgrade to version 5.3 twice, but each time the process is failing.
I have downloaded the ISO and burned to disk, backed up the system and kicked off the upgrade. It states it completes, informs me that I can eject the disk and reboot the system. However I have discovered I've been having to manually shut the server down and restart it, but it boots up into 5.2.3.
Is there something I am missing?
Thanks much.

Paul,
I assume that you were connected to CIMC, KVM or Physical Monitor/Keyboard when the remote upgrade was triggered. You do have to select few options when the remote upgrade happens, The only thing you avoid in remote upgrade process is - burning the DVD and inserting it in the drive.
I'd recommend that you setup CIMC (SETUP instructions :
http://www.cisco.com/en/US/products/ps10493/products_configuration_example09186a0080b10d66.shtml)
or KVM and open a TAC case, TAC can see where exactly the failure is happening.
I assume that you have already backed up 5.2.3's CONFIG+CONTENT before starting the upgrade to 5.3. The sysmptoms described in this thread are vey unique and would need deeper investigation.
Also once the device is UP via SSH , Get a syslog out of the device for analysis. The syslog contains dmsupgrade.log which should help TAC determine the root cause.
Worst case scenario, you may have to re-image the system using 5.2.3 FRESH ISO (different than upgrade ISO, this image can be obtained via TAC) , restore the CONTENT and CONFIG (assuming you have the backup of both) and re-trying the upgrade.
Or if this is fairly new setup you can also choose to run 5.3 FRESH ISO (assuming you don't want to retain any content and config)
I'd recommend opening a TAC case to troubleshoot this further.
Thanks,
Sagar Dhanrale

Cisco meeting place 8.0 upgrade media download or PUT and upgrade process?

Hello all, I have been given the task to upgrade our cisco meeting place sever version 8.0.1.3 on both the app server and web sever.
We have a valid UCSS and I would like to go to version 8.5 Is this something I can order via PUT or can I download one of the upgrades I see on cisco's website?
Also I'm a little confused on the upgrade process. I've read another post that I have to export the exsisting data then do a fresh install of 8.5 then import the data..... Is this true?
Thanks,
Dan

Hi Playne,
It depend what kind of deployment is running right now. Please read this article:
http://www.cisco.com/en/US/docs/voice_ip_comm/meetingplace/8_5/english/administration/migrate_matrix.html#wp1031995
From Release 8
For complete information on compatibility requirements for Release 8.5, see the Compatibility Matrix for Cisco Unified MeetingPlace Release 8.5 at http://www.cisco.com/en/US/products/sw/ps5664/ps5669/products_device_support_tables_list.html.
Table 5 Migration Process For Different Deployments From MeetingPlace Release 8.0
FROM
Current System
TO
Audio Only
TO
MeetingPlace Scheduling
MeetingPlace-Driven User Management
TO
WebEx Scheduling
MeetingPlace-Driven User Management
TO
WebEx Scheduling
WebEx-Driven User Management
Audio/Video Only
Migrating from Cisco Unified MeetingPlace Release 7.x or 8.0
Not supported
Not supported
Provision a new Cisco WebEx site.
Migrating Using the MPtoWebEx CSV Converter
Meetings are not migrated. Keep your existing system to play existing recordings.
MeetingPlace Scheduling
WebEx Conferencing
MeetingPlace-
driven User Management
Migrating from Cisco Unified MeetingPlace Release 7.x or 8.0
Migrating from Cisco Unified MeetingPlace Release 7.x or 8.0
As required, coordinate with your Cisco WebEx CSM to upgrade to the Cisco WebEx WBS27 SP27 or later Release.
Not supported
Provision a new Cisco WebEx site.
Migrating Using the MPtoWebEx CSV Converter
Meetings are not migrated. Keep your existing system to play existing recordings.
WebEx Scheduling
WebEx Conferencing
MeetingPlace-
driven User Management
Not supported
Not supported
Migrating from Cisco Unified MeetingPlace Release 7.x or 8.0 module
As required, coordinate with your Cisco WebEx CSM to upgrade to the Cisco WebEx WBS27 SP27 or later Release.
Provision a new Cisco WebEx site.
Migrating Using the MPtoWebEx CSV Converter
Meetings are not migrated. Keep your existing system to play existing recordings.
WebEx Scheduling
WebEx Conferencing
Webex-driven User Management
Not supported
Not supported
Not supported
Migrating from Cisco Unified MeetingPlace Release 7.x or 8.0
As required, coordinate with your Cisco WebEx CSM to upgrade to the Cisco WebEx WBS27 SP27 or later Release.
Please remember to rate useful posts clicking on the stars below.
Favor calificar todos las respuestas útiles dando click en las estrellas de mas abajo.
LinkedIn Profile: do.linkedin.com/in/leosalcie

After upgrading to 27, firefox will not start. Saw an error message during the upgrade process.

After upgrading to 27, firefox will not start. Saw an error message during the upgrade process but cannot remember.
Tried to run firefox.exe -P but receive error message:
XML Parsing error: undefined entity
Location: chrome://mozapps/content/profile/profileSelection.xul
Line number 18, Column 1:
<dialog
^
Running on Windows XP SP3. No problem whatsoever before upgrading to 27. Sending this from Chrome as I cannot open Firefox at all.

Thanks jschaer2000: after starting it once in safe mode, I closed Mozilla and tried several restarts in normal mode. So far, all worked:-)
Thank you very much again.
Still the automatic update process bothers me: it took me several days to discover the reason to the malfunction, since when I removed the problematic version from Add and Remove Programs, I didn't pay attention at first that it was another version, not v26 which I installed from my folder.
In addition, I like to save the installation files before I run new programs and if I didn't have v26 exe file, I couldn't have operated Mozilla at all. Not that it was fun to remove and install again each time v27 didn't react, but it was better than nothing, I still prefer Mozilla over its competition.

Moving from 32-bit to a 64-bit OS how will this impact ebs upgrade process

we are planning to upgrade from ebs 11.5.10.2 to r12.1 .3
My concern is since we will be moving from 32-bit to a 64-bit OS how will this impact our upgrade process?

Hi;
we are planning to upgrade from ebs 11.5.10.2 to r12.1 .3
My concern is since we will be moving from 32-bit to a 64-bit OS how will this impact our upgrade process?I assume your EBS single machine. EBS r11 is not certified wiht 64 bit OS.So you need to upgrade first than migrate it 64 bit
See:
32bit to 64 bit migration-EBS-Linux
EBS r12 migrate 32-bit to 64-bit.
32 bit to 64 bit 11i migrate
Migrattion of E-Business Suite.
Regard
Helios

BPC 7.5 upgrade process - Doubts

Hi,
Once we had the confirmation and approval to upgrade the system from SP00 to SP03 (on .NET server components), we noticed that some functional configurations had been made in the meantime. This new scenario where new things had been done from a functional perspective makes me wonder if any of that configuration could be lost while or after upgrading the server component?
Also, after reading Note 1453797 - Planning and Consolidation 7.5 SP03 NW Central Note, section "Before you install" to be more specific it says to uninstall any previous version of the .NET server and client components. Also Scott recommended me that as a best practice. This applies when the upgrade is being done from BPC 7.0 to BPC 7.5 for example or it also applies to my case (uprading BPC 7.5 system from SP00 to SP03)?
Thanks again for your help.
Regards

Hi Ethan,
Thanks for the quick response.
Actually I'm new installing BO BPC and maybe I've not used the correct words to describe that configuration I've detected while trying to install SP03. What I've noticed is that an Initial Application Set has been created. Actually, this is the only thing I have found but I'm not sure if that imply any other configurations either in .NET server or ABAP server that could be lost after upgrading the server component from SP00 to SP03. The same question arises if I decide to uninstall the current installation to perform a fresh one using SP03 directly as its described in note 1453797.
In summary, is there any chance to lost the configuration made on a BPC system (.NET and ABAP servers or client) if any of the above upgrade process is performed?
Hope being clear enough this time thanks so much for your help.
Kind regards

ADM(Anomaly Dectector Module) PowerDown Failure in upgrade process.

Similar Messages

Maybe you are looking for