Admin page unable to access
I am running Win XP pro 64. I have a WRT54G Router hard wired to my computer thru a, Network Everywhere (Linksys) model NC100U-WM ,PCI card.I want to set up a wireless network in my house to share the dial-up Internet connection. I have tried the http://192.168.1.1. I only recieve "this page cannot be displayed" . Thanks in advance for any help.
pennylane wrote:
Routers are meant to be used for broadband connection but it will also work with dial-up by configuring your computer as a proxy server. Please tell us how you connected things and not kinda sure if NC100 has drivers for 64-bit OS already.
to expand on what pennylane said....
if your ethernet cable has one end in one of the ports labled 1-4 and the other end is in your network card you also need to have your network card configured to use dhcp.
if this is the case then you can confirm that 192.168.1.1 is the correct address for managing the router by typing ipconfig from the command line
start > run > cmd
the above should get you to a command window
type ipconfig
this should display your ip adderss, the subnet and an address for a gateway.
the gateway is the address for your router when directly connected as described above.
you should also be able to ping the gateway address.
type ping 192.168.1.1
if you are able to do all this but not able to get to the address the possibly you have a 3rd party software firewall installed.
the below thread may be useful to you in that case.
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&message.id=581
Similar Messages
-
Flash Admin Console Unable To Access
This may sound like a newbie question so i apologize if it sounds a bit dumb... My problem is that I am unable to login into my Flash Administration Console. I have typed in the correct username and password however, it keeps coming back has failed.
To the best of my knowledge port 1111 is working although, i don't how if there is a method of checking port 1111 to see if it is open or blocked.
When i login i give my username and password...There is the default server 1. In regards to server address...Is the server address just your computer ip address or something else? A little a confused here. Any help would be most welcome.Hi,
This is a basic thing but could you check if your Admin Server is running? If its a windows machine then under Services check for Flash Media Administrator Server and if it is linux check if fmsadmin process is running.
Thanks,
Apurva -
Unable to Access Router Admin Page
So I have a weird situation where my router is working fine to allow me access to the internet, yet I am unable to access the router administration page, 192.168.1.1 This occurred after the router froze up tuesday. I reset the router to factory defaults and have since been able to get online, but not access admin page. Router is a Linksys WRT-54GS V 7
Modem is motorolla SB1505
ISP is earthlink, but in NYC so its actually off the Road Runner network. Cable connection obviously. - I attempted to access 192.168.1.1 with both Mozilla Firefox and IE 8. FIrefox gives an "Unable to connect" error message. IE 8 redirects me to search engine results (yahoo in this case).
-Ipconfig confirms default gateway and DHCP server is 192.168.1.1, subnet mask 255.255.255.0
- I am able to ping the router with <1ms times.
- I have tried resetting router to defaults again, but same issue occurs.
- I am able to get online and access web pages, etc.
- Tried resetting up the router using the Linksys setup program, but it error every time saying "please connect router for broadband"
- Router worked fine with me able to access admin page until it froze up yesterday.
- Wireless works fine. Though the network is unsecure atm, since I can't access router admin.
- I've also tried disconnecting all other devices from the router except my computer and modem. Still wont let me access router. System is running windows 7 PRO, fully updated. However, I can't access the router either on 2 other computers at home which run windows XP PRO SP3. System Specs CPU: Intel i5 running at stock speeds
Mobo: Gigabyte P55-UD4P
Ram: Gskill Ripjaw, 4 gb DDR3-1600 7-7-7-21
HD: Intel X-25 M 80 gb G2.
PSU: Corsair CMPSU 750 TX
GPU: Diamond ATI 5850 Anyone have any ideas on whats wrong here? Did i miss something obvious? Would greatly appreciate any help as having an unsecure wireless network in the middle of NY isn't the best idea. Thanks!
Message Edited by Banthracis on 11-06-2009 04:25 PMI am once again unable to access the on-line Router admin page. When I use the EasyLink Advisor and click ADVANCED settings it pulls up the browser but goes nowhere. If I type in the address directly it does the same thing. The address I'm typing is correct. I know because if I unplug the router for a minute, I can get on using the EasyLink or entering the address directly into the browser. Then I sign in and can access the pages.
Why do I have to keep resetting the router to access the router admin pages? It doesnt matter about virus protection, firewall, what version of Windows I'm using, what browser I'm using...the only thing that matters is resetting the router.
And now I have a new problem. When I attempt to go online with my new netbook, it causes my wired-to-the-router desktop to loose the connection, even though I reset the router and "added it as a new device".
I was using Homegroup to access the netbook the first day I got it. Now I cannot access the netbook or the network from the netbook, without resetting the stupid router every single time. I am not using mac address filtering and have the router set to allow 9.
Getting fed up with this router and I never get an answer from Linksys as to why I can never access the router admin pages without resetting the stupid router.
I can get the netbook on other people's wireless networks (using their password) but cannot get onto my OWN using my password.
Does anyone have any ideas? I'll try anything before yanking this thing out and buying a different brand of router. Yeah I'm mad, sorry.
Wired desktop Windows 7 Home Premium 64/IE8/using Windows firewall and MS Security Essentials. Netbook is W7 Starter, Norton Internet Security 2010. But none of this matters. Because I had the same problem with this router using Vista64, IE7, no firewall, no a/v, IE32 & 64 bit...all those variables yet the only thing that works is resetting the router.
SO WHAT DOES MATTER? Help me before I trash this thing please.
mlure -
Wrt54g ver5, unable to access the config pages
wrt54g ver5
firmware ver 1.02.5
i am unable to access the internal web pages on wrt54g ver 5
can access the internet fine. it seems to be a memory corruption problem
i has been doing more and more timesSince the router works, it is doubtful (but still possible) that the firmware is corrupted. More likely there is another explanation for your problem. Here are my tips for viewing your router's web pages:
You do not need an Internet connection. The router's "web pages" are built into the router.
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
Point your browser to 192.168.1.1 , then login to your router. Your user name should be left blank. Your password is "admin" (with no quotes), unless you changed it.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
Some Zone Alarm users have reported that adding 192.168.1.1 to their list of "trusted" addresses fixed the problem. This trick might also work with other firewalls.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
If you still have trouble, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it. -
Unable to access site page in sharepoint2010
Hi,
I am unable to access the site page with read permissions,while accessing i am getting the following error. for this i am not get any proper log information.Please guide me on this.(Note:we can able to logon witth the same page with contribute permissions)
Thanks in advance.You need to check the logs for details. You can do the following, you will need SharePoint admin access for this
If a correlation id is available, merge the logs from all servers using the following command:
Merge-SPLogFile-Path"<Path\error_ProblemId.log"-Correlation"correlationID"
If the correlation Id is not available in the log, then enable verbose log, follow the following commands to enable and then disable the verbose log. Caution: Verbose log can consume lots of storage space, so reproduce
the issue and turn it off immediately.
Set-SPLogLevel -TraceSeverity verbose
New-SPLogFile
Reproduce the issue, and then immediately run the below commands:
Clear-SPLogLevel
New-SPLogFile
Regards, Mahesh -
Unable to access values from database in login page..
Hey all,
Friends I have a login.jsp page and I want if i enter username and password then it will be accessed from database and after verifying the details it will open main.jsp.I made a database as "abc" and created DSN as 1st_login having table 1st_login. But the problem is that I am unable to access values from database.
So Please help me.
Following is my code:
<HTML>
<body background="a.jpg">
<marquee>
<CENTER><font size="5" face="times" color="#993300"><b>Welcome to the"<U><I>XYZ</I></U>" of ABC</font></b></CENTER></marquee>
<br>
<br>
<br>
<br><br>
<br>
<form name="login_form">
<CENTER><font size="4" face="times new roman">
Username
<input name="username" type="text" class="inputbox" alt="username" size="20" />
<br>
<br>
Password
<input type="password" name="pwd" class="inputbox" size="20" alt="password" />
<br/>
<input type="hidden" name="option" value="login" />
<br>
<input type="SUBMIT" name="SUBMIT" class="button" value="Submit" onClick="return check();"> </CENTER>
</td>
</tr>
<tr>
<td>
</form>
</table>
<%
try {
Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
Connection connection = DriverManager.getConnection("jdbc:odbc:1st_login");
Statement statement = connection.createStatement();
String query = "SELECT username, password FROM 1st_login WHERE username='";
query += request.getParameter("username") + "' AND password='";
query += request.getParameter("password") + "';";
ResultSet resSum = statement.executeQuery(query);
//change: you gotta move the pointer to the first row of the result set.
resSum.next();
if (request.getParameter("username").equalsIgnoreCase(resSum.getString("username")) && request.getParameter("password").equalsIgnoreCase(resSum.getString("password")))
%>
//now it must connected to next page..
<%
else
%>
<h2>You better check your username and password!</h2>
<%
}catch (SQLException ex ){
System.err.println( ex);
}catch (Exception er){
er.printStackTrace();
%>
<input type="hidden" name="op2" value="login" />
<input type="hidden" name="lang" value="english" />
<input type="hidden" name="return" value="/" />
<input type="hidden" name="message" value="0" />
<br>
<br><br>
<br><br>
<br><br><br><br><br>
<font size="2" face="arial" color="#993300">
<p align="center"> <B>ABC © PQR</B>
</BODY>
</HTML>
and in this code i am getting following error
C:\Project\SRS\build\generated\src\org\apache\jsp\loginjsp.java:93: cannot find symbol_
C:\Project\SRS\build\generated\src\org\apache\jsp\loginjsp.java:93: cannot find symbol_
C:\Project\SRS\build\generated\src\org\apache\jsp\loginjsp.java:94: cannot find symbol_
C:\Project\SRS\build\generated\src\org\apache\jsp\loginjsp.java:95: cannot find symbol_
4 errors
C:\Project\SRS\nbproject\build-impl.xml:360: The following error occurred while executing this line:
C:\Project\SRS\nbproject\build-impl.xml:142: Compile failed; see the compiler error output for details.
BUILD FAILED (total time: 6 seconds)As long as you're unable to compile Java code, please use the 'New to Java' forum. This is really trival.
To ease writing, debugging and maintenance, I highly recommend you to write Java code in Java classes rather than JSP files. Start learning Servlets. -
OIM 9.1.0 installation- Unable to access Admin console
Hello OIM Gurus,
I'm new to OIM. I am trying to setup OIM 9.1.0 one of windows VM. After the installation i'm unable to access to oim admin console using link http://localhost:8080/xlWebApp
If I try to access the above URL i get "The requested resource (/xlWebApp) is not available" message.
Here are the details for the environment
Environment: Windows Server 2003 R2
OIM Version: 9.1.0
App Server: jboss-4.0.3SP1
Database (OIM repository): MS-SQL server 2000 sp4
Please throw some light on this.
Thanks.Thanks Kevin. I have looked at the setup-jboss.profile.log inder <OIM_HOME>\xellerate\logs . I could find the below error
move] Moving 1 files to C:\oracle_idm\xellerate\webapp\precompiled
[move] Attempting to rename: C:\oracle_idm\xellerate\webapp\precompiled\jsp-temp\tjspIndex.jsp to C:\oracle_idm\xellerate\webapp\precompiled\tjspIndex.jsp
[jasper2] log4j:WARN No appenders could be found for logger (org.apache.jasper.compiler.JspRuntimeContext).
[jasper2] log4j:WARN Please initialize the log4j system properly.
[jasper2] Error in class org.apache.jasper.JspC
BUILD FAILED
file:C:/oracle_idm/xellerate/setup/jboss-setup.xml:245: org.apache.jasper.JasperException: Unable to initialize TldLocationsCache: null
at org.apache.tools.ant.TaskAdapter.execute(TaskAdapter.java:155)
at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:193)
at org.apache.tools.ant.Task.perform(Task.java:341)
at org.apache.tools.ant.Target.execute(Target.java:309)
at org.apache.tools.ant.Target.performTasks(Target.java:336)
at org.apache.tools.ant.Project.executeTarget(Project.java:1339)
at org.apache.tools.ant.taskdefs.Ant.execute(Ant.java:39
Do you have any idea how do i fix this issue? Any help would be really appreciated. -
Unable to Access SSL WebVPN Login Page
I am unable to access the SSL WebVPN login html page. I tried using FF, Chrome, and IE via https://24.43.XXX.XXX. All I get is "Page cannot be displayed". I am stumped here, any help would be greatly appreciated.
PLAN-FW# show run
: Saved
ASA Version 9.1(1)
hostname PLAN-FW
domain-name intranet.example.com
enable password s9HtiQv6kkqqiJhc encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
ip local pool VPN-Clients 192.168.5.2-192.168.5.220 mask 255.255.255.0
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 24.43.XXX.XXX 255.255.255.252
interface GigabitEthernet0/1
channel-group 1 mode active
no nameif
no security-level
no ip address
interface GigabitEthernet0/2
channel-group 1 mode active
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
nameif Management
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Port-channel1
nameif DR-01
security-level 100
ip address 10.0.0.1 255.255.255.252
ftp mode passive
dns domain-lookup outside
dns server-group DefaultDNS
name-server 8.8.8.8
name-server 4.2.2.2
domain-name intranet.example.com
object network obj-internet
subnet 0.0.0.0 0.0.0.0
object network obj-vlan100
subnet 10.0.100.0 255.255.254.0
object network NETWORK_OBJ_192.168.5.0_24
subnet 192.168.5.0 255.255.255.0
pager lines 24
mtu outside 1500
mtu DR-01 1500
mtu Management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-713.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (DR-01,outside) source static any any destination static NETWORK_OBJ_192.168.5.0_24 NETWORK_OBJ_192.168.5.0_24 no-proxy-arp route-lookup
object network obj-vlan100
nat (DR-01,outside) dynamic interface
route outside 0.0.0.0 0.0.0.0 24.43.XXX.XXX 1
route DR-01 10.0.0.0 255.255.255.252 10.0.0.2 1
route DR-01 10.0.100.0 255.255.254.0 10.0.0.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 Management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint SELF-TP
enrollment self
fqdn intranet.example.com
subject-name CN=intranet.example.com
keypair myrsakey
crl configure
crypto ca trustpool policy
crypto ca certificate chain SELF-TP
certificate 4fb08954
30820203 3082016c a0030201 0202044f b0895430 0d06092a 864886f7 0d010105
05003046 311e301c 06035504 03131569 6e747261 6e65742e 70656c61 74726f6e
2e636f6d 31243022 06092a86 4886f70d 01090216 15696e74 72616e65 742e7065
6c617472 6f6e2e63 6f6d301e 170d3134 31323136 31313237 32315a17 0d323431
32313331 31323732 315a3046 311e301c 06035504 03131569 6e747261 6e65742e
70656c61 74726f6e 2e636f6d 31243022 06092a86 4886f70d 01090216 15696e74
quit
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev2 remote-access trustpoint SELF-TP
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point SELF-TP outside
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2
anyconnect profiles Example_Intranet_client_profile disk0:/Example_Intranet_client_profile.xml
anyconnect enable
tunnel-group-list enable
group-policy "GroupPolicy_Example Intranet" internal
group-policy "GroupPolicy_Example Intranet" attributes
wins-server none
dns-server value 8.8.8.8 4.2.2.2
vpn-tunnel-protocol ikev2 ssl-client
default-domain value intranet.example.com
webvpn
anyconnect profiles value Example_Intranet_client_profile type user
username test1 password GxmPkeumVbHvz58J encrypted privilege 15
username test2 password t.GxS9C3hRYHni61 encrypted
username test3 password M9Szy/s33Cm6Crby encrypted
username test4 password hMXxQZTu8agZnzki encrypted
tunnel-group "Example Intranet" type remote-access
tunnel-group "Example Intranet" general-attributes
address-pool VPN-Clients
default-group-policy "GroupPolicy_Example Intranet"
tunnel-group "Example Intranet" webvpn-attributes
group-alias "Example Intranet" enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly 10
subscribe-to-alert-group configuration periodic monthly 10
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:4976c27fbf11ae4589d27b4f16107a41
: end
Directory of disk0:/
10 drwx 4096 08:15:36 Sep 19 2014 log
20 drwx 4096 08:16:04 Sep 19 2014 crypto_archive
21 drwx 4096 08:16:12 Sep 19 2014 coredumpinfo
114 -rwx 37416960 08:24:28 Sep 19 2014 asa911-smp-k8.bin
115 -rwx 18097844 08:26:28 Sep 19 2014 asdm-713.bin
116 -rwx 69318656 08:27:50 Sep 19 2014 asacx-5500x-boot-9.1.1-1-RelWithDebInfo.x86_64.img
117 -rwx 12998641 08:47:34 Sep 19 2014 csd_3.5.2008-k9.pkg
118 drwx 4096 08:47:36 Sep 19 2014 sdesktop
119 -rwx 6487517 08:47:38 Sep 19 2014 anyconnect-macosx-i386-2.5.2014-k9.pkg
120 -rwx 6689498 08:47:40 Sep 19 2014 anyconnect-linux-2.5.2014-k9.pkg
121 -rwx 4678691 08:47:42 Sep 19 2014 anyconnect-win-2.5.2014-k9.pkg
122 -rwx 200 14:26:42 Dec 08 2014 upgrade_startup_errors_201412081426.log
129 -rwx 338 11:59:35 Dec 16 2014 Example_Intranet_client_profile.xml
8238202880 bytes total (4860497920 bytes free)
Cisco Adaptive Security Appliance Software Version 9.1(1)
Device Manager Version 7.1(3)
Compiled on Wed 28-Nov-12 11:15 PST by builders
System image file is "disk0:/asa911-smp-k8.bin"
Config file at boot was "startup-config"
PLAN-FW up 5 days 5 hours
Hardware: ASA5515, 8192 MB RAM, CPU Clarkdale 3059 MHz, 1 CPU (4 cores)
ASA: 4096 MB RAM, 1 CPU (1 core)
Internal ATA Compact Flash, 8192MB
BIOS Flash MX25L6445E @ 0xffbb0000, 8192KB
Encryption hardware device : Cisco ASA-55xx on-board accelerator (revision 0x1)
Boot microcode : CNPx-MC-BOOT-2.00
SSL/IKE microcode : CNPx-MC-SSL-PLUS-T020
IPSec microcode : CNPx-MC-IPSEC-MAIN-0022
Number of accelerators: 1
Baseboard Management Controller (revision 0x1) Firmware Version: 2.4
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 100 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Active perpetual
Encryption-DES : Enabled perpetual
Encryption-3DES-AES : Enabled perpetual
Security Contexts : 2 perpetual
GTP/GPRS : Disabled perpetual
AnyConnect Premium Peers : 100 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 250 perpetual
Total VPN Peers : 250 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 2 perpetual
Total UC Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
IPS Module : Disabled perpetual
Cluster : Disabled perpetual
This platform has an ASA 5515 Security Plus license.Hi Nathan,
Are you using Ikev2 to connect. If not then can you please remove the following command and then try again:
no crypto ikev2 enable outside client-services port 443
Thanks
Jeet Kumar -
I am unable to access my email from Charter.net. I can sign in with my password, then a message comes up which says "The plug-in for this page has been disabled. Click here to manage your plug-ins." All of my plug-ins are enabled. What am I missing?
After a great deal of searching I ran across the suggestion to disable all plug-ins and then, one by one, enable them until finally the problem was solved. I am not sure which plug-in was causing the problem, as I am satisfied to have the problem solved. I am going to leave the rest of the plug-in disabled.
-
Unable to access application set in admin console after upgrade to 7.0 M
Hi Experts
I am unable to access the Application Set through BPC Administration after upgrading our development server to version 7.0 SP3. I followed the instructions as per the Upgrade guide, and there was no issues during the installation. But when trying to access the application set i receive the following error message on step 9 ( 9/10) of during the connection.
Error message: Subquery returned more than 1 value. This is not
permitted when the subquery follows =, !=, <, <= , >, >= or when the
subquery is used as an expression.
I have done all of the steps outlined as per SAP Note 1242962, but i still receive the error message. I tried to do a SQL Profiler trace, but i have been unable to find the query which returns more than one record.
Any help is appreciated
Kind Regards
DanielInteresting that you ask about upgrade vs uninstall/reinstall.
We were running BPC 5.1
We have also re-installed the Admin client to be the new version.
We have been working with an outside consulting firm to manage our system upgrade/install.
Our dev and qa environments were uninstalled then reinstalled.
When we went to production, our system was intially upgraded. I do not know why this route was chosen when that was not what was completed on dev/qa. On our production 'upgrade', we are still working through issues. We then uninstalled iis, sqlserver reporting services, both .net 1.1 and 2.0, and the BPC application. Then reinstall everything and we were getting the same errors.
Our error was at Progress 10/10 Create Database Schema and check Application server collation.
Error Message: Object Reference not set to an instance of an object.
We are able to access the appShell and test copies of the appShell, we were not able to access any custom appSets which were created prior to the upgrade, nor are we able to access any appSets that were created as a copy of the custom appSet after the upgrade.
When logged with SAP, we were directed toward note Note 1331040 - Cannot log into 7M Admin console after restore from version5 noting that we needed to do the following changes:
Note that you will need to change the following:
INSERT INTO tblDefaults VALUES ('_GLOBAL','Prev_AppSet_Version','','','7.0.112')
INSERT INTO tblDefaults VALUES ('_GLOBAL','Curr_AppSet_Version','','','7.0.112')
to
INSERT INTO tblDefaults VALUES ('_GLOBAL','Prev_AppSet_Version','','','7.0.113')
INSERT INTO tblDefaults VALUES ('_GLOBAL','Curr_AppSet_Version','','','7.0.113')
The reason is because '7.0.113' means 7 MS SP04 while '7.0.112' means SP03.
There are 8 steps in this note, for us, only the first 2 were needed. I have asked SAP to create new note/update existing accordingly.
With the table entry, we were able to successfully access our app set.
Hope our experiences can help you out.
Thanks,
Becky Zick -
I am unable to access my mail account on my iphone, which I have been able to do previously. I press the mail icon, the page refreshes to the mail format page - blue bar top and bottom, white text space in the middle.... and that is as far as it goes. It does not list my email accounts or offer any.
Close the mail app, double tap the home button and completely close out of the app.
then do a reset, no data loss. Hold down the home/sleep button together until you see the apple logo and then release, then wait for the phone to boot back up. -
Authentication failed accessing admin page.
Hi,
I deployed NW NC7.1 on AIX, the deployment went through fine. I have admin servlet configured to be only accessible by users with an admin role.
So I created a new user, and mapped both this user and the administrator user to the admin role.
When accessing the admin page, I was prompted for authentication info. I tried to login with the new user, and also the admin user, none of them works.
Please help!
Thanks!Managed to sort that one - switched it off for a while !!
-
Unable to access "Cache Hierarchy Server" config pages
BM 3.9 SP2
NetWare 6.5 SP8
In iManager I am unable to access the Cache Hierarachy Server/Client config pages.
In IE7 the page is just blank
In FireFox I get the error "The timer value cannot exceed 1 hour"
Does anybody know how to fix this - it is urgent!
Thank you in advancelaurabuckley,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://forums.novell.com/ -
Username password error when ifolder admin access admin page
OS: SLES 10 SP4 i586 + online updates
OES2 SP3 + online updates.
Today, I was configuring a POC demo of iFolder to a customer, and faced the following:
iFolder configured with MS AD 2003, and initial configuration(simias-server-setup, ifolder-admin, ifolder-web) went smooth, without errors. But I can't login via ifolder admin(ifadmin) user when accessing Admin Page(http://ip/admin) I got incorrect username password error.
As already informed, that iFolder configuration went smooth(error free) and iFolder Administrator account, plus iFolder Proxy accounts are all available in MS AD 2003, also I have provided the
appropriate DN during configuration(but still I am getting 'username password' error when accessing admin page).
logs says following:
2011-12-01 16:31:18,403 [Simias Manager Start] INFO Simias.Service.Manager - "Simias Change Log Service" service started.
2011-12-01 16:31:18,404 [Simias Manager Start] INFO Simias.Service.Manager - "Simias Local Domain Provider" service started.
2011-12-01 16:31:18,422 [Simias Manager Start] INFO Simias.Service.Manager - "Simias iIdentity Sync Provider" service started.
2011-12-01 16:31:18,426 [Simias Manager Start] INFO Simias.Service.Manager - "Simias Journal" service started.
2011-12-01 16:31:18,470 [Simias Manager Start] INFO Simias.Server.Service - Could not load the configured user provider - loading InternalUser
2011-12-01 16:31:19,580 [Simias Manager Start] INFO Simias.Service.Manager - "Simias Server" service started.
2011-12-01 16:31:19,582 [Simias Manager Start] INFO Simias.Service.Manager - "Simias Report" service started.
2011-12-01 16:31:19,584 [Simias Manager Start] INFO Simias.Service.Manager - "Simias User Movement Plugin" service started.
please help asap.Issue resolved by changing
LdapResyncOnRestart=No
to
LdapResyncOnRestart=Yes
Regards,
Muhammad Sharfuddin
Originally Posted by sharfuddin
OS: SLES 10 SP4 i586 + online updates
OES2 SP3 + online updates.
Today, I was configuring a POC demo of iFolder to a customer, and faced the following:
iFolder configured with MS AD 2003, and initial configuration(simias-server-setup, ifolder-admin, ifolder-web) went smooth, without errors. But I can't login via ifolder admin(ifadmin) user when accessing Admin Page(http://ip/admin) I got incorrect username password error.
As already informed, that iFolder configuration went smooth(error free) and iFolder Administrator account, plus iFolder Proxy accounts are all available in MS AD 2003, also I have provided the
appropriate DN during configuration(but still I am getting 'username password' error when accessing admin page).
logs says following:
please help asap. -
Unable to access SOA suite start page from remote browser.
I have Oracle SOA Suite 10.1.3 and Oracle 10g AS 10.1.2 installed on a Windows 2000 machine.
I am able to access the default start page of the 10.1.2 AS from the local and remote machine using the following URLs
Http:\\hostname:7777\
Http:\\hostname:80\
Also, I am unable to access the SOA Suite 10.1.3 start page, bpel console etc - from the host machine using Http:\\hostname:8888\
However from a remote machine browser I am not able to connect to the start page of SOA suite only. Http:\\hostname:8888\.
Is there some settings which allow only local host access to the SOA suite pages?.
All the hosts are on the same intranet, there is no firewall. Also i have Msft loopback adapter installed on the server host machine.
Appreciate all suggestions.
ThanksI suppose you're using DHCP and hope you have followed the steps in the Installation Guide. With DHCP it is always a bit tricky to access the server. You should check your /WINNT/system32/drivers/etc/hosts file. If the hostname you're using during install is not in it then adding it will help.
--olaf
Maybe you are looking for
-
HP C309g scanning software for windows 8.1
How do I scan from my HP C309g into my computer using Windows 8.1?
-
Linking to a vCard file in Firefox
I just tried to add a link to download a vCard (.vcf) file - seems to work fine in Internet Explorer, but in Firefox, it just shows up in the browser window like a text file. http://www.kameli.com/tcleaves.html i've seen other websites where you can
-
Using JavaCompiler together with a Library
Currently I am developing a tool in which Java Source Files are created based on a XSD file with help of a tool named Castor. After the generation of the files the files need to be compiled in order to be used by the program. This used to be done wit
-
Item and Item description as Levels ?? In Demantra
I have Item defined as the lowest level and its description also being defined (as level description) in oracle Demantra. From the staging table - I bring in item and item description. In the Oracle Demantra seeded model - I find that Item has been d
-
Why is there no "back" arrow to go back to the previous viewed site? == This happened == Every time Firefox opened