Admin Passord on Configuration page

My 8500A has stopped recognising my wireless connection. I have to go through setup (enter my network name and password) every time I want to print. When I print out the Network Configuration Page , Admin Passowrd is shown as Not Set. I have restored Factory Settings and gone through the set up again but still have to reenter my network name and password in order to activate the printer.
Also the Wireless Network Test Report print out shows every thing ok, PASS on all items under Diagnostic summary
BTW, my Mac OS is 10.9
Thank you

Hi baoluo,
Welcome to the HP forums!
I see you have an Officejet 8500A that no longer holds a wireless connection for very long. I'm sorry to hear this, but I will certainly do my best to assist you with this!
I will recommend that you follow Solution five in this Printer Does Not Maintain Wireless Connection document to set the printer with a static IP address. There are quite a few steps in this document, so if the static IP doesn't help make sure to browse the rest of the document for other things you can try
Hope to hear back from you soon!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

Similar Messages

Ent 9 - Can't run mgmt console - admin.cwr gives Error 404: page not found

Post Author: Alan Weiner
CA Forum: Deployment
We just did a fresh install of Crystal Enterprise 9. When we try to run the Management console, we get an "Error 404: page not found"
http://wdcwfc80/crystal/enterprise9/admin/en/admin.cwr
Error 404: The page cannot be found

Post Author: Alan Weiner
CA Forum: Deployment
From the server (although, it uses a browser to connect)
colin mackenzie:
Hi Alan Weiner.
Do you get this message when you run this from the server? or just the workstation / client browser?

When trying to log in as the Admin user, get "error on page"

Hi gurus, I am brand new on this new product. Yesterday I just downloaded the latest Apex (2.2) and installed it successfully by following the instuctions (for I got these two lines in the install log: Thank you for installing Oracle Application Express.
Oracle Application Express is installed in the FLOWS_020200 schema.
). I have got two problems. First, when I try to log in as the Admin user, and as soon as I start typing the user name and password on the logon page, I see "error on page" at the very lower left corner of the browser (IE 6). So I can not log in. Second, the Oracle HTTP server takes up almost 100% of my CPU (by itself, the 10g instance does not take up any noticeable CPU if I am not doing anything, but the HTTP server keeps the CPU busy all the time no matter what).
What did I do wrong? Please help me. Thanks a lot.
Ben

Hello user526627 and all,
I also have installed apex 2.2 successfully. At least I've not found any errors and this is the tail of install.log:
Thank you for installing Oracle Application Express.
Oracle Application Express is installed in the FLOWS_020200 schema.
The structure of the link to the Application Express administration services is as follows:
http://host:port/pls/apex/apex_admin
The structure of the link to the Application Express development interface is as follows:
http://host:port/pls/apex
timing for: Upgrade
Elapsed: 00:00:00.12
JOB_QUEUE_PROCESSES: 10
Completing registration process.
Validating installation.
timing for: Validate Installation
Elapsed: 00:03:18.10
timing for: Complete Installation
Elapsed: 00:38:11.54
Interesting thing is that I am getting 404 when I use suggested http://host:port/pls/apex/apex_admin or http://host:port/pls/apex (I am using host name of the machine or ip address). However the http://host:port/pls/htmldb/ and http://host:port/pls/htmldb/apex_admin works (at least, I am getting a page without images). In addition, when I provide user name and password on the http://host:port/pls/htmldb/apex_admin page and click on 'Login' nothing happens... :(
This is a clean install. I've also used a HTMLDB 2.0 install from companion cd (Oracle10g R2 for Windows) - this had worked ok, however it did stop working when I istalled apex 2.2 on top of it. I've dropped flow-schemas and tablespaces I've created for apex 2.2 install and started the install over again. However, still no luck. Here is the command I am using to start apex 2.2 installation:
@apexins ********** htmldb_data htmldb_files htmldb_temp /i/ none
I have installed oracle http server in a standalone home, the http server works.
Thank you for your time,
Daniel

Admin tool: login.jsp (blank page)

I have a problem similar to a recent posting.
I have a 9i Release 2 database installation, server works, sample jsps work, database is up.
Updated the file $ORACLE_HOME/ultrasearch/webapp/config/ultrasearch.properties with our info.
When I try to access the admin page (http://rockfish:7778/ultrasearch/admin/index.jsp) I get to the login page, but it is blank (html body tags, but nothing to display).
The .class and .java file are created in ultrasearch/webapp/isearch_admin/_pages
Is that right? should they be under htdocs/_pages?
Is single sign-on possibly a source of my problem?
Any help would be greatly appreciated,
John

Hi, John:
Does anybody know how to correctly set "AdminConstants.JSP_SRC_HOME" ? Yes.
in ultrasearch.properties file, you need to set the correct admin.srchome variable ->
"Do not use $ORACLE_HOME for admin.srchome , please enter the real file path"
So your ultrasearch.properties file should look like:
=====================================================
connection.driver=oracle.jdbc.driver.OracleDriver
connection.url=jdbc:oracle:thin:@localhost:1521:swims9i
admin.srchome=C:\\oracle\\ora9i\\ultrasearch\\webapp\\isearch_admin
=====================================================
Here is a webIV note explain this problem in details: (you can also find this note in metalink)
http://webiv/cgi-bin/webiv/do.pl/GET?WwwID=Note.202949.1&List=ARTICLES&ARTICLES.Idx=4
Hope this is a clear,
Cindy

1505n printer wired to network will not print configuration for IP address

I have a HP 1505n printer that will not the configuration page so that I can get the IP address to set it up. I know it's not the cat5e cable because I've tested it by plugging my laptop to and it works fine. The operating system is Windows 2008r2. I currently have 2 other 1505n printers which work great using a HP universal driver. Cat5e cable unplugged it will print and UBS cable connected to a PC it will print a usb config page. I followed HP's advice on resetting the printer but get the same results. Any suggestions?

Hi Marcel17,
I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this by clicking the following link: Printers - LaserJet.
Hope this helps, have a good one!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

EPrint Configuration: Option to remove document URL

Hi,
thank you very much for providing this useful app.
I am having trouble configuring the printer-settings when printing out a document that is stored online (e.g. Google Docs or iWorks, when documents are opened through the ePrint browser): I cannot print the document without it's URL being displayed on top.
So far the ePrint app for the iPad only allows me to display or remove the URL on the bottom of the document, however it is always displayed on top of the document (even in bold letters).
It is imperative for this app to be able to print out documents whithout bold URLs on top of them in order to make ePrint useful for printing regular documents such as letters etc.
Could you please offer the option to remove the URL on top of a page in the next Update of ePrint for the iPad?
Thank you very much!

Hi Warren,
there's a 4th option:
Simply set the "write raw string" input of the write key function to TRUE
This option only appears when a string is wired to that function!
Just re-checked:
I think it's a limitation of the config file format. It's text based and (leading) spaces in the value are "overseen" as whitespaces. So your next option would be to use quotes around your string with spaces...
Message Edited by GerdW on 05-02-2009 08:32 PM
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Sound card configuration not appropriated?

Hello,
I work about the 3 h tutorial of NI and reached page 50 of the dokumnet. exercise 3.2. Variant C.
Does anyone know how I can find the reason for the problem and the solution, having the following error:
error 4803 bei Audioaufnahme->Daten.vi (sound acquisition)
possible reasons::
LabVIEW: (Hex 0x12C3) Die angegebene Konfiguration eignet sich nicht für den Treiber oder die Karte für Audiodaten. Stellen Sie sicher, dass sich die eingegebenen Parameter innerhalb des unterstützten Bereichs für die Hardware und Treiber befinden.
(LabVIEW: (Hex 0x12C3) = The given configuration is not appropriated for the driver or the card for audio data. Make sure that the entered parameter are within the supported range of the hardware and drivers.)
I downloaded Labview 2012 (about 1 Gb file) of National Instruments -website. May the drivers be absent??
Grüße
Thommy7571
Solved!
Go to Solution.

If the settings made in the Express VI aren't compatible with the hardware (sound device) in the machine then this error shows up.
Can you share the configuration/settings you've made in the express VI...??
It should look very similar to below picture.
Also: For Windows, you must have DirectX 8.0 or later to use this VI and for Linux you must have the Open Sound System (OSS) driver to use this VI.
I am not allergic to Kudos, in fact I love Kudos.
Make your LabVIEW experience more CONVENIENT.

T42 Restore factory configuration impossible - but recovery part exist

Hello,
I have a T42 (IBM bought in my business school)
When I bought it the PC had 4 part in the Hard Drive
2 part visible
- C: SYSTEM
- E: USER DATA
1 part hidden
- IBM_Service W: (the recovery part) - all the program and a 2 drive partition C and D or E
+ BIOS
To be able to restore the factory configuation I had in the menu to start Windows Two choices
- Start Windows normally
- Restore factory configuration
Due to a problem on the laptop I had to restore the factory configuration 2 or 3 times in the last two yearss. It worked well two times.
But Last time the Laptop did not recognize after the restoration the E: DRIVE. It was on the computer but with no name and no possibility to access it.
I uses TESTDISK to regive a name E to this part and be able to use it and restore the data in it but during the process the Recovery part (Drive W which was hidden appeared on the System list
On the same time the choice "Restore factory configuration " on the list of the start of Windows disappear. I use my friend computer to put back on the list the name of the choice but this link can't restore the Factory configuration because it is no longer configurate for it.
Is there a possibility to boot the PC on the Recovery part in order to restore the factory configuration?
does this manipulation will keep my 2 drive configuration C: + USER DATA drive (E with all the data saved in it? That works the first two times
Thanks in advance for your help
This will help me very much
Thieum
Sorry for the english I did my best

Thumper wrote:
I also have a T42, but it’s a different model. I once tried my disks
on a T41 that I was trying to revive, and they didn’t work...
and was later told by IBM that each machine has unique disks.
Whoever told you this was mistaken. With the exception of hardware changes (eg modem from T41 to T42) the disks within a series should work just fine (I've just recovered aT41 with my T42 CDs). The only difference in using early T42 recovery with a later T42 is the fingerprint reader. Later T42 disks should work just fine with an early T42. Go ahead and use your T42 disks on her machine.
Keith
Formerly 600E 2645, T30 2366, X31 2673, T40 2373, T41 2379, T42 2373, T42 2379, T60 1952, T61p 8889, T61p 8891
Currently T420 4177-CTO, T430 2347-A54, T430 2349-L64, T430 2347-UN9, T430 2342-CTR, Ideapad K1, H520S 2561-1LU

Wireless Zero Configuration or Access Connections.

Which is better to use and faster? I have T61.

Problem solved - apparently this is caused by the Google Latitude gadget I installed on my iGoogle home page. Took it off and now all is welll...

The "write key" configuration file vi use of "trim string" prior to writing the data can modify any string data written.

I tried to use the config VIs to record some front-panel settings for later restoration, one of which could be a single space character (part of a string parsing system).
I soon discovered that whenever I tried to save that single-space value to an INI file, only a null string was saved.
After doing some digging I discovered that buried in the Write Key vi is a worker vi called Config Data Modify that uses Trim String on the string data before it is written to the file and that's what was eating my string character. I don't know whether this is a bug or a feature but there are at least three ways to fix it.
1) Assuming you want to leave the library VIs alone, you can pre-process any stings sent to "write key" to replace all spaces with "\20" and then post-process all strings read using "read key" to replace all instances of \20 with spaces.
and if you don't mind modifying the library VIs, either to save/use under a different name or to stick back into the library in a modified state (caution - can cause problems when you move code to another machine with an un-modified library) then...
2) You can yank the trim-string out of the Config Data Modify vi and hope that it does not have any undesirable side effects with regards to the other routines that use Config Data Modify (so far I have not found any in my limited testing)
or
3) You can modify the string pre-processing vi, Remove Unprintable Chars, to add the space character to the list of characters that get swapped out automatically.
Note that both option #1 (as suggested above) and option #3 will produce an INI file data entry that looks like key="\20Hello\20World\20" while option #2 produces an entry that looks like key=" Hello World "
The attached PDF contains screenshots of all this.
Attachments:
Binder1.pdf ‏2507 KB

Hi Warren,
there's a 4th option:
Simply set the "write raw string" input of the write key function to TRUE
This option only appears when a string is wired to that function!
Just re-checked:
I think it's a limitation of the config file format. It's text based and (leading) spaces in the value are "overseen" as whitespaces. So your next option would be to use quotes around your string with spaces...
Message Edited by GerdW on 05-02-2009 08:32 PM
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

"Display cannot switch to secondary landscape with this configuration" Error on x201 T

Hi, I've just bought x201 for 2 weeks. Today I tried to rotate the screen in tablet mode so I can get the battery with my hand when I read documents but after rotation and after just 1-2 second it automatically get back to primary landsacpe view and gives me this error. I wonder what is the problem and more importantly what is the solution?
thanks

More info: I turned off auto-login, and was able to log in to my test account. Then, I was able to use fast user switching to switch to my main account. I will try again restarting into my main account and see if I can switch to Test. This failed consistently before I posted here. Perhaps the "sense Mac guru" circuit kicked in and cured the problem. I'm about ready to turn in so won't post a follow-up until tomorrow. Right now, I need to use my two accounts to get the job done (a writing job with screen shots of a new unaltered account). Then, I'll go back to trying to see if the problem still exists when I log in to the main account first.

How to open a configuration file with a relative path?

I want to open a configuration file during the initialization of my application (first "state," u can say) and I am using "Open Config file.vi" and tried to pass the config file's path as "data\myconfig.ini" and the "File exists?" vi didn't give any error (simply, the output was "false") but the Open config File gave an error.
If I pass an absolute path "D:\xyz\xyz\myconfig.ini" it works fine. Isn't it allowed to use "relative path" as I remember using it before for other tasks?
I actually prefer to have this file in the "data" folder that my application's setup will create in the destination directory while installing the application, because it will be easy when I want to ask the user to open and edit it. Or, I would just put it in "C:\" which exists on all the windows computers, but then it would be too much open.
Thanks ahead!
Vaibhav
Solved!
Go to Solution.

Relative paths have sometimes a meaning for command line tools (where a relative path gets appended to the current path, which usually is the executables directory).
But for Windows GUI applications that makes not much sense. Windows also maintains a per process current path, but that path gets updated by several Windows APIs, one of them being the File Dialog. So whatever your user has last selected in any file dialog inside your application will from then on be the applciations current path. It should be clear that with such a braindamaged current path implementation it has basically no useful meaning, and LabVIEW consequently does not do path expansion, where relative paths are expanded by prepending them with the applications current path.
Also LabVIEW uses mostly the Windows 32 Bit API, which does provide the current path implementation but does almost not use it in any of its file operations. The use of that feature is mostly reserved for the Windows shell API, which is a higher level API that can as best be described as a collection of various APIs that have been thrown together by whatever some MS developer felt at the moment. You can not by any means call it a designed API at all, and LabVIEW makes almost no use of it, as it needs lower level access, to make its operation similar in its working across all the platforms, LabVIEW can run on.
So while you can work with relative paths inside your application (and actually should as much as possible to make your application not depend on a particular location) you should make that path absolute whenever you pass it to a function that actually accesses a file somewhere.
Rolf Kalbermatter
Message Edited by rolfk on 09-08-2009 11:31 PM
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

How can I print out the objects with the configuration and connections? I want to document my programming (configuration) on paper.

Solved!
Go to Solution.

The datamember configurations can be exported. In edit mode, File->Export Process Data Members...
But the connections cannot be exported.
You can open the .lks file by notepad, there you will see the source codes, including the connections you configure. But you need to extract them manually.
Ryan Shi
National Instruments

App not supported by your device's current configuration

Hi, If I try install some apps from Appworld (especially the converted android apps) I get a message that it is not supported by my device configuration. Is this a regional issue in that only people in specific countries can access the apps? Cheers

aandras wrote:
Do you have a specific app that you got this with. This way it can be tested.
An example is the podcast app for OS 2.0 as well as the below app:
http://appworld.blackberry.com/webstore/content/73867/?lang=en&ei=S75XT6aXGOyp0AXqj6jwDQ&usg=AFQjCNG...

How to get the configuration of a bank (not with FP get configuration info)?

Hi everybody!
    I need my fieldPoint application to be able to check
for the filedpoint structure, that is I want my application
to return the number of FP nodes, and for each node how many FP IO modules are connected, and of which
type.
   I'd like not to use "FP get configuration info",
which is based on locating the .iak file. I have my .iak file
correctly generated, but I do not want to use it.
   At the end, I'd like to have a variable configuration, and when I change module order and number, I don't want
to re-generate a .iak file, (because I don't want to use MAX... ).
   Should I query my modules until I reach an error?......
graziano

First of all, thanks, Khalid!
   I want to use the COM port. I gave a look to the "Find
FP-100x example", based on optomux commands, and I found it very
interesting, to my purpose. But I have some questions about it.
   First of all, in the example I have to provide explicitly
an address (the fp1001 address, 0x0 for me), so I should build a loop,
in which I scan all possible addresses (that is 0, 10, 20,... ) which
generate many errors, in normal conditions.
    After this, in the example I get a Module ID, which is:
   FP1001 -----> ID: 2
   FP-DI-301 --> ID 105
   FP-DO-401 --> ID 106
   FP-DI-301 --> ID 105
   FP-DO-401 --> ID 106.
   The list actually matches the order of my FP chain, but
I'd like to know if these IDs are given to the modules when
they're configured for the first time in MAX, or are set in HW?
   Thanks!
graziano

Admin Passord on Configurat​ion page

Similar Messages

Maybe you are looking for

Admin Passord on Configuration page