ADSL Checker Information Changed?

Hi
Last week when I entered my phone number into the ADSL Checker it stated:
Your exchange is ADSL enabled, and our initial test on your line indicates that it is VERY UNLIKELY you will be able to receive fixed 512Kbps broadband service due to the very long length of your telephone line. However, your order will be accepted if you still wish to order.   Our test also indicates that your line currently supports an estimated ADSL Max broadband line speed of 1Mbps; typically the line speed would
But when I have checked again today it now says:
Your exchange is ADSL enabled, and our initial test on your line indicates that your line should be able to have an ADSL broadband service that provides a fixed line speed up to 512Kbps. However, due to the length of your line, an engineer visit may be required, who will, where possible, supply the broadband service.
Our test also indicates that your line currently supports an estimated ADSL Max broadband line speed of 750Kbps; typically the line speed would range between 750Kbps and 2.5Mbps.
Our test also indicates that your line should be able to have an ADSL2+ broadband service that provides a fixed line speed up to 512Kbps. However, due to the length of your line, an engineer visit may be required, who will, where possible, supply the broadband service.
Our test also indicates that your line currently supports an estimated ADSL2+ broadband line speed of 1Mbps; typically the line speed would range between 1Mbps and 3Mbps.
The only thing that has changed in the meantime is that I have had my BT Total Broadband connection connected. Could the ADSL Checker data have been updated off the back of that?
I'm convinced BT have the wrong information on file regarding my line's broadband/infinity potential and this latest change of information on their website seems a potential further pointer to this perhaps being the case?
In addition, average speed from Speedtest.net shows 0.3mps so far...albeit I'm within the initial 10 day period but nevertheless will it really jump to 1-3mb average by the end of the test period?

OK thanks John, here's the information as requested:
- ADSL Stats
ADSL Line Status
Connection information
Line state:
Connected
Connection time:
0 day, 09:56:03
Downstream:
416 Kbps
Upstream:
448 Kbps
ADSL settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
7.2 dB / 8.0 dB
Line attenuation (Down/Up):
63.5 dB / 31.5 dB
Output power (Down/Up):
15.3 dBm / 12.5 dBm
FEC Events (Down/Up):
37415 / 18
CRC Events (Down/Up):
407 / 15
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
HEC Errors (Down/Up):
530 / 21
Error Seconds (Local/Remote):
0 / 0
More Details
- BT Speedtest Result
Download speedachieved during the test was - 0.14
Mbps
For your connection, the acceptable range of speeds is 0.1 Mbps-0.5 Mbps.
IP Profile for your line
is - 0.37 Mbps
Upload speed achieved during
the test was - 0.31Mbps
Additional Information:
Upstream
Rate IP profile on your line is - 0.45 Mbps
- Master Socket = ADSL socket but when I plug internet cable into left hand socket, nothing happens, so instead I have plugged into right hand socket (with microfilter) and this is working.
- 17070 Test 2 (quiet line) = silent

Similar Messages

  • No Check Information generated.........?????

    Hi Friends
    Got a doubt in APP.
    we hav 2 house banks: IDBI - A/c ID-1234 and SCB- A/c ID- 2222. For both banks Cheque Lot 1 has been created with 100 cheques in each lot.
    Now while running APP i want to print checks. But the problem is that when we run APP with house bank IDBI a new check is created automatically. But if we run APP using HB- SCB, though the payment is made to vendor no check information is created. All parameters and variant details remain same. only thing changed in ZRFFOUS_C: 'Variant' is House Bank from IDBI to SCB or vice-versa as required. Output device is also maintained.
    So why is this happening? Like if I pay from one bank to same vendor check information is generated and if i pay that vendor thru other bank No check information is generated.?
    Can anyone pls share something on this. (Bit Urgent pls)
    Thank You

    hi
    after creating proposal, select "edit proposal"button-ok
    and double click on line item which you want to payment-ok
    and again double click on line item-ok
    and you can see one dialog box, on this box see reallocate button as bellow of that-ok
    and select that, and enter payment method, housebank details in two fields-ok
    and save it back..
    now continuee normal procedure-ok
    all the best
    RGS

  • BBP_PS_PROJECT_GET_LIST: Checks for Change Authorization.

    Hi,
    I have a custom SAP program that is required to fetch pertinent details from a project.
    The SAP function module BBP_PS_PROJECT_GET_LIST retrieves several internal tables is used for this purpose. 
    For some reason this function module, which looks like it should only retrieve information and cannot perform changes itself, checks for Change authorization to object C_AFKO_ACT.  As a result, users with Change access to projects can run this and get the appropriate results (in internal table IT_AFVC).  However, users with Display access only to projects do not have any data returned back in this same structure.
    Any idea on how to go about this problem?
    Regards
    Jibat

    Hi,
    See also the foll related  notes before you implement the corrections in the note 818342 based on your current SP level for SRM 4.0.
    Note 742314 - BADI for approver selection when adding/changing approvers
    Note 802581 - Error in call "BBP_WFLH_AGENTS_FOR_CHANGE_GET"
    BR,
    Disha.
    Do reward points for  useful answers.

  • SFW5 (BF) does not show me Check / Activate Changes button in ECC 6 EHP4

    Hello All,
    i am facing a strange problem, i want to activate business Function 'HCM, Core Processes in Talent Management' (BF name 'HCM_TMC_CI_1') in ECC6 EH4 IDES system. I also have SAP enterprise SearchTREX installed and this component shows me dependency in green light in SFW5 tcode (that means all the pre-requisites are fullfilled).
    But in SFW5 tcode does not show me Check / Activate Changes button on the top bar, and if i see in menus its greyed out i am not able to activate the same.
    I tried to unlock client using tcode SE06 and SCC4 but nothign worked out.
    I even checked the authorization of user it has sap_all, SAP_new, IDES_IDA_SUP, IDES_SWITCH, R3_TRUSTED.
    I will appreciate any help on the same.
    We developed system from Homogenious Export Image provided by SAP to us.
    Mani

    Hello Mani,
    You have to check for the compitability and dependency of already activated Enterprise Extension. If an incompatible Extension set is activated than it wont allow other application to work. Please check and let me know if you require anymore information.
    Regards,
    Vinit Pagaria

  • What is the command to check the changes in the spanning-tree topology?

    What is the command to check the changes in the spanning-tree topology?

    Hi,
    Few commands which would help are:
    1- Show spanning-tree detail
    2-show spanning-tree detail | in ieee|from|occur|is exec  >> This will give from were the changes occuring- Ex:
    C6K1#show spanning-tree detail | in ieee|from|occur|is exec  
     VLAN0001 is executing the rstp compatible Spanning Tree protocol
      Number of topology changes 9536 last change occurred 00:00:29 ago
              from GigabitEthernet4/6
    3- show spanning-tree active  *& show spanning-tree root >> Will give you the root information.
    4-  show spanning-tree inconsistentports >> If there are any port which are inconsistent state due to STP features.
    STP running MST:
    ===============
    show spanning-tree mst configuration  >> Need to check and match the same outputs with the other switches running in the same MST domain/region.
    show spanning-tree mst detail
    show spanning-tree mst <name of the region>
    Debug on STP:
    ============
    debug spanning-tree events/bpdu >> would be good but to be run with more cautious.
    HTH
    Inayath
    *Plz rate if this info is usefull.

  • Check Information is already exist in Check Management

    Hi,
    I have created a wrong Check lot in T.Code FCHI i.e. 492800 - 493000     insted of  4926800 - 4927000
    I realized after generating the checks till 492807 then I Voided the remainng checks (492808-493000)with the reason Test printing. and created new check lot with correct number 4926800 - 4927000 and created these all checks manully from FCH5 and check register also updated
    Then after we created a check lot 4928000 - 4928200 and checks generated without any problem till 4928079
    But when i create check information for the check number 4928080 system is giving Message " The check information already exists in check management. Changes have been saved " . If  I try to display the Check information from FCH1 for the check 4928080 it is displaying the Chek lot 492808 - 493000 which i voided earlier with th reason Test Printing....
    I am unable to update the check register whenever i create a check .... its always saying
    Invalid Check lot  492808 - 493000
    Void reason - 1 (Test Printing)
    Voided on DD/MM/YYYY
    Voided by USER NAME
    I am really surprised why system is behaving like this even the check number is not falling in to the voided check lot
    Please suggest..
    Regards,
    Shivaji

    resolved

  • Where we can check the changes that we have done in the Projects

    Dear Friends,
    I have done few changes in the project WBS element after saving the Project, Now I want to check what all the changes that I have done in the WBS.
    In which transaction I can check these changes apart from u201CCN60u201D, and please explain step by step what all the customizing setting are required to check these changes.
    In Projects is it possible to check the way we are checking the changes in PO and Sales Orders.
    Regards,
    Sai

    Nitin Patoliya,
    Thanks for the inputs, I have tried as you suggested there it is showing system status Created and released, but Iu2019m not getting the information as I required. Here exactly what Iu2019m looking is If I have done any changes in the Project, Eg: after saving the Project if I have changed the Business area, profit center u2026.etc, I need the information when I have changed this data and at what level (WBS, Network or Activity).
    Regards,
    Sai

  • How to check the change log of a variant

    Dear Gurus,
    I want to check the changes done (Change log) in a variant of a program. But i could not find any options around. Please suggest me how can I find the changes done on a variant.
    Thanks in advance.
    RathiM

    Hi Koteswar!!
    Vishal was perfect in his reply to your query. But still as you insisted here comes a step by step elabu2026
    1.     Execute the transaction SE38
    2.     Give the program name in the field against the Program
    3.     In the sub objects section select the radio button variants
    4.     Click on Display
    5.      You will now lead to the ABAP: Variants initial Screen where you enter the variant name in the field against the Variant
    6.     Now traverse through the path utilities-Find  from the main menu
    7.     You will be prompted with a Find variant Popup where you can give the respective variant name and click on execute.
    8.     Yow will be returned with a screen having information regarding Variant name, short description, Environment, Protected, Changed by and Last Changed.
    Trust that suffice to your query!!
    Regards,
    Damanaidu J
    Edited by: Damanaidu jawaharlal on May 22, 2011 1:01 PM

  • BT Openreach ADSL Checker

    Why all of a sudden is the Openreach ADSL checker reporting that my line speed would only go up 8mb when a month ago at was showing upto 14mb and I'm clearly getting around 14mb on my line anyway?
    Bit concerned that this database error will affect things when I can apply for Infinity in my area when it goes live in March.
    Regards
    Simon

    Hi do not worry it will have no affect on infinity as that is a totally separate product and when available will show your approximate speed for that service the data base change to reflect occasional connection changes certainly do not worry also please remember infinity live dates are estimates and may and do change
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

  • BT ADSL Checker

    Hi All,
    I have used the new checker at https://www.dslchecker.bt.com/pls/adsl/adslchecker​.welcome
    One question what does this statement mean:
    The Stop Sale date for Datastream is from 30-Jun-2012; the Formal Retirement date for Datastream is from 31-Mar-2014.
    Hope someone can help.
    Thanks

    Hi Keith,
    I have just run the ADSL Checker (first time for some months) and that seems to have changed format, viz :-
    BROADBAND AVAILABILITY CHECKER
    Telephone Number *************** on Exchange KIMBOLTON is served by Cabinet 2
    Available ProductsDownstream Line Rate(Mbps)Upstream Line Rate(Mbps)Downstream Range(Mbps)Availability Date
    Featured Products
    WBC ADSL 2+
    Up to 2
    1 to 3.5
    Available
    ADSL Max
    Up to 1.5
    1 to 2.5
    Available
    WBC Fixed Rate
    0.5
    Available
    Fixed Rate
    0.5
    Available
    For all ADSL and WBC Fibre to the Cabinet (FTTC) services, the stable line rate will be determined during the first 10 days of service usage. Throughput/download speeds will be less than line rates and can be affected by a number of factors within and external to BT's network, Communication Providers' networks and within customer premises.
    The Stop Sale date for Datastream is from 30-Jun-2012; the Formal Retirement date for Datastream is from 31-Mar-2014. The Stop Sale date for IPstream is from 31-Oct-2013; the Formal Retirement date for IPstream is from 31-Mar-2014.
    If the End User wishes to migrate from their current Broadband supplier they will need to contact them in the first instance to obtain a MAC (Migrations Authorisation) Code, and then contact their new Broadband supplier to arrange for the service to be migrated.
    Note: Please note that postcode and address check results are indicative only. Most accurate results can be obtained from a telephone number check.
    Thank you for your interest.
    Was it some sort of update by BT Wholesale like the speedtester ?
    Best regards,
    dfenceman

  • Control-k key binding broken. How can I check and change my key bindings?

    I use the Terminal app a lot. Unfortunately I am not able to use the control-k shortcut to cut lines in the terminal anymore. How can I check (and change) the Terminal key bindings?
    Thank you!

    Basing on your input, you should get the following values:
    1) session keys
    SK_ENC: 6DCE2A99BACB5207A7A96A92F114D66C
    SK_MAC: 0D446132B168F75CD6F0A780693A4DD3
    SK_DEK: 19F7B0F94837F32874B29B5EFB7809F6
    2) host cryptogram
    1B781553209748EA
    3) Retail MAC
    01761103B810F00E
    Summing up, the External Authenticate command should have the following value:  84 82 01 00 10 1B781553209748EA 01761103B810F00E.
    Try to compare it with your results.
    Regards

  • How to check and change the dafault session timeout of the Portal?

    Hello,
    When leaving a portal page open without using it for a certain amount of time and then accessing it again the Session times-out.
    Where can I check and change this default time-out time in case I would like to extand it for the end users?
    Roy

    Hi Roy,
    Session timeout includes multiple settings (J2EE setting and SSO setting at User Management).
    Defining the Timeout in J2EE Session
           1.      Open file web.xml (path depends on the version of EP6.0. If it is based on NW04, then
    ..\cluster\server0\apps\sap.com\irj\servlet_jsp\irj\root\WEB-INF
           2.      Enter a value in minutes under <session-timeout>. The value should roughly correspond to the length of a synchronization cycle. The default is 30 minutes.
    After a successful login, it receives a SSO ticket which is valid for longer duration (generally 8 hrs, default which you can changed using  "System Admin" as mentioned by Yoel.
    Thanks,
    Swapan

  • Payment document updated after payment run but no check information

    Now Folks help out with this one.
    We have the Payment Run completed and one vendor is missing a check. we look into the account and see that we have a payment document to this account so posting key 25 Vendor, and 50 Bank. but no check information.
    I can go in and reverse this document and manually input a check but in my next payment run another 4 vendors have no check info,
    so i cannot even cancel or reprint becos i have no check number I can only reverse
    HELP!!!!!!

    hi,
    u have to check if for the line item if payment is done or not if the payment is done u have to write the manual check and assign the check numbre to the payment line item for this u can used FCH4 or FCH4.
    hope this is clear. assign.
    With regards
    Krishna.

  • How to check mass change(vendor) done by any particular user .

    Hi,
    What is a transaction used  to check mass change(vendor) done by any particular user .
    Thanks,
    Dharmesh

    HI
    pls try this table CDHDR
    Thanks & Regards
    Phaneendra

  • When in mode dev to develop my website, I can't open buttons and PDF files to check my changes or somebody else's changes. What is wrong ? (I updated  Adobe Reader)

    when in mode dev to develop my website, I can't open buttons and PDF files to check my changes or somebody else's changes. What is wrong ? (I already updated  Adobe Reader)

    Oh no... NOT THE 99-PAGER!!! Anything but THAT!!!

Maybe you are looking for