Advanced Format Hard Drive not recognized by HP DV6000 Controller

Hello,
I have an HP DV 6000 laptop (6276 I think, I'm at work can't check) that came preinstalled with a Western Digital 160gb 1.5gb/s 5400 RPM drive (Vista) that failed a couple of weeks ago.  So i bought a Western Digital 750 GB WD Black SATA III 7200 RPM 16 MB drive to replace it. I read about people having some problems with Advanced Drive Format hard drives not being recognized by their controller, but also read that depending on the controller and specific Dv6000 model laptop they had-one wouldn't run into problems. 
Well sure enough, when attempting to install Windows 7 I received the error that the hard drive was not detected. After researching online I came across an article on WD's site that noted
"Our SATA II hard drives use autospeed negotiation. This enables our SATA II drives to automatically detect the motherboard data transfer rate, making it backward compatible with SATA I data transfer rates. However, some older SATA I controllers are unable to support autospeed negotiation and cannot recognize the drive. This “drive not detected” condition occurs when a chipset is incapable of correctly negotiating the data transfer speed with a SATA II hard drive."
my drive is a SATA ||| but I'm pretty sure it's the same problem.  The site goes on to say a fix would be to  "purchase and install a third party PCI or PCI-Express Second Generation Serial ATA controller card for your Serial ATA hard drive(s)."
My question(s) are.
1)Is the problem that I am trying to install a Sata ||| hard drive on a laptop with a controller that will only recognize SATA | hard drive?
2) Or is the problem that the hard drive is an Advanced Drive Formatted hard drive and I need to buy a hard drive with out that specification?
3) Or Should I buy a SATA controller card as WD suggests on their website and if so will this definitely allow my laptop's controller to recognize the new hard drive and proceed with the installation?
4)Or Should I just return the hard drive and buy a SATA | non Advanced Drive Format hard drive? (question 2 basically)
Thanks for your help!

Hi @jasmine00 
Welcome to the HP Support Forums.
I certainly understand your issue with the drive upgrade. Unfortunately it is a bit of the nature of notebooks, the sacrifice of a large amount of upgradeability, in exchange for compactness and portability. Whenever a new technology comes out, older notebooks are never really going to be easy to upgrade, it at all. Normally the unit as a whole is tested with a set list of hardware, and only those items are supported.
That being said there is this document that could be helpful with your problem.
Preparing Advanced Format hard drives for Microsoft Windows installations on HP Business Notebook PC...
And for your reference:
HP Pavilion dv6000 Notebook PC Maintenance and Service Guide
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

Similar Messages

  • Thunderbolt partitioned and formatted hard drive not recognized on USB2/3

    I have a MBA (mid 2012) and recently purchased a Seagate Desktop Thunderbolt Adapter (STAE129), a Seagate Backup Plus 4TB USB 3.0 external drive (STCA4000100), and Apple Thunderbolt cable. The 4TB hard drive can be separated from the USB 3.0 adapter and the drive placed on the Thunderbolt adapter. I created two partitions (3TB and 1 TB) on the 4TB drive while it was mounted on the Thunderbolt adapter and formatted them Mac OS Extended (Journaled) using partition map scheme GPT. Everything works as expected, the drive hits r/w speeds in the 180 MB/s range (using Blackmagic Disk Speed Test), and no issues at all transferring data to the 3TB partition and using the 1TB partition for TimeMachine.
    However, if I disconnect the hard drive from the Thunderbolt adapter and place it on the USB 3.0 adapter and connect it to my MBA, Mountain Lion says "The disk you inserted was not readable by this computer and gives me the options to Initialize, Ignore, or Eject. Going into Disk Utility app, the drive shows up without the partitions I created when the same drive was mounted to the Thunderbolt adapter (just shows disk1s1). In fact, the drive label (Disk Description) is different too and the Partition Map Scheme now shows MBR!
    To try work-arounds, I went ahead and repeated the partitioning and formatting steps with the drive attached via USB 3.0 and all works fine until I put the drive back on the Thunderbolt adapter where once again OSX reports that the disk is not readable. I've even tried a single partition with no luck. In short, the drive partitioned and formatted on Thunderbolt is unrecognized under USB and vice versa.
    Shouldn't the disk preparation and data be consistent across these different interfaces? I would think so. My biggest concern is that if I had a failure in the Thunderbolt setup (assuming the drive itself does not fail), then I can't access my data. This is not a very comfortable situation.
    I'm assuming I've overlooked a very basic detail. Appreciate any steer to solve this problem.
    Thanks,
    Rob

    Thanks for that, I recently ran into the same problem. I even chatted with Seagate tech support and they didn't know the answer.
    My situation is a bit different from you. I bought the 3 TB Thunderbolt version of the drive directly and then purchased a USB 3 adaptor seperately.  You see, I still own a 3 year old Macbook Pro that doesn't come with a Thunderbolt port. I was looking to upgade to a MacBook Air later.  I thought that I might as well buy the TB version now.
    In anycase, my old MacBook Pro won't see the drive when I use the USB3 adaptor. I get the same exact error message as you did. I can't really test it on Thunderbolt since I don't have one.  I'm going to go install the Thunderbolt drivers now and hopefully, it will recognize the drive afterwards.  I'll let you know what happens.
    BTW, I was thinking of reformatting the drive with NTFS so that I can use the drive on PCs. My mac has the NTFS drivers loaded so it's no problem. I hope this won't screw up the Thunderbolt connection later when I do get the Macbook Air?

  • Hard drive not recognized during windows server 2008 setup

    hard drive not recognized during windows server 2008 setup

    Hi,
    Whether the hard disk is recognized in BIOS?
    Connect it to another computer to see if it could be recognzied incase the cause is the disk itself. Also please check if it is really a RAID instead of a single hard disk - a single disk should be recognized directly while RAID cannot be recognized until
    a suitable driver is installed.
    Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • SOLARIS OS Support for Advance Format Hard Drives

    Hello,
    I am fairly new to the UNIX Operating System so I'm hoping that someone can help me. Does Solaris support the new Advance Format hard drives (4k sector boundaries)? I cannot find any mention of the advance format drive in the Oracle literature. I believe, based on my recent reading that Open Source Solaris depends on ZFS to handle the support of the new 4kbyte sector size.
    Thank you in advance for any information you can supply.
    Steve

    Moderator Action:
    This post has been moved to the Solaris 10 forum.
    @ O.P.,
    You originally posted your inquiry to the Clustering forum, which has nothing to do with the topic of disk cluster size.
    Glance at the documentation for Oracle Cluster 4.0 to see what clustering is all about.

  • Replacement hard drive not recognized in mac mini

    Hi folks,
    I have an issue similar to several threads that were active during 2007 and 2008, but the information and answers given then do not solve my problem.
    The original 80 GB Hitachi drive in a 1.5 Mhz PPC failed. I replaced it with a Western Digital PATA 320 GB ide drive and reassembled the Mac Mini.
    The original Apple OS X was put in the optical drive and the computer was started with the "c" button pressed when powered on, but repeatedly the disk was ejected after a short time.  Since the mac mini does not boot from the proper install cd, I cannot use disk utilities to partition and format the WD drive per the other thread messages.
    The WD drive is not formatted for Apple yet. I connected the headless mac mini to an older ibook with a firewire cord and I attempted to boot the mac mini in target disk mode.  The ibook never mounted the mac mini as an external drive, an icon did not appear on the desktop, and running disk utilities on the ibook did not recognize the mac mini connected by firewire as a mounted drive.  I mounted an Acom hard drive connected by fire wire as a test of the ports and wires and that device was recognized in disk utilities and an icon for it  was seen on the desktop.
    Back to the issue at hand.  What else can I do to partition and format a new hard drive installed in an older mac mini where 1) the install disk is kicked out of the optical drive and 2) the unformatted drive cannot be accessed via target disk mode from an ibook?
    Is 320 GB incompatible with a PPC mac Mini?
    Thanks in advance for offers of help and correct answers.
    Mich

    Hi Mich,
    the older PPC computers are usualy limited to 128Gb max. HD size.
    You need something like this:
    "MacOS X 10.4.x and Earlier Hi-Cap Installer.app"
    Its available for $25 here:
    http://www.intechusa.com/

  • Memory modules and hard drive not recognized

    I removed and reinserted the factory installed Satellite L505D-LS5007 laptop hard drive and memory modules just as practice for installing a hard drive upgrade and an 8GB memory upgrade. The problem is obviously with the memory and not with the hard drive.
    After the first practice try, one memory module was recognized. Also for a few seconds after the first practice try, I ran the PC with the battery installed, but no memory installed. I did not look in the User's Guide first to see that I should have removed the battery before removing the memory.
    Now the System Indicator Lights for the HDD Activity and Memory Card Reader do not light up. The PC turns on and the display is solid black with no messages.
    Before buying new memory modules, what possible ways might there be to get the PC to recognize the factory installed memory modules and hard drive again?
    Solved!
    Go to Solution.

    When troubleshooting, I always change one variable at a time. I would hate to miss a solution by being in a hurry. In this case, you may have damaged either the RAM or the RAM slot. I would stick with the Toshiba specifications for the RAM, making sure it is the correct size, speed and type recommended. I also recommend that when you replace the RAM that both modules be from the same manufacturer, size, and specification. Try one RAM module in one slot and then the other. And then try both RAM modules in both slots. After the testing you should be able to figure if this is a RAM problem or a RAM slot problem.
    In the case of hard drives, the real test is whether or not the Bios sees the hard drive. If the Bios doesn't see the hard drive, it's not going to work. The Bios should see the hard drive whether or not the hard drive is partitioned, formatted or has data on it. My experience has been that many Toshiba laptops will work fine with larger capacity hard drives provided they are the same speed in RPMs, have the same interfacing connection and physically the same size.
    Again, prior to doing any work on your computer, make sure that both the AC power has been disconnected and the battery has been removed. Be careful out there. A blown repair job by a non-Toshiba tech is NOT covered under warranty.

  • New internal hard drive not recognized at all!

    Hello everybody!
    I really need your help. I tried to upgrade my internal 120gb drive to a Western Digital wd2500bevs. But when I start my Macbook with the Leopard DVD neither the System Profiler nor the Disk Utilities Program recognize the drive for a possible installation. When I reinstall the old drive everything is back to normal and works perfectly.
    This is what I already tried to fix the problem:
    I took the drive into an external casing => it was recognized immediately
    I then formatted it => no change after installing it into the Macbook again.
    I cloned my system with CCC on the WD and then installed it => no system found.
    I have another disk of this kind but the same problem and another 160gb Toshiba disk which is not recognized as well.
    Please help me! I couldn't find help in German discussions yet so I hope anyone of you guys can help me.

    You say the drive is "recognized" but your original post stated it was not present in Disk Utility. I'm puzzled. Have you attempted to partition and format the drive?
    Extended Hard Drive Preparation
    1. Boot from your OS X Installer Disk. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.)
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.

  • IBook G3 hard drive not recognized

    I have a challenge for anyone. I have a ibook 366(clamshell) that is not recognizing the hd. It was working wonderfully one night I shut it down and the next day I get the flashing question mark. I've tried all of the normal stuff: zap pram, reset nvram tried to use command and s but it didn't go to the programmers screen and all the such. I can boot from a cd but none of the utilities see the hd. I have taken the hd out and connected it to a usb to ide cable that allows me to use it as an external drive and it is recognized without any problem on all of the other macs I connect it to and even on a pc (I know I said the bad word.)Does anyone have any clue what could be the issue. Every thing else seems to work fine. Just the hd is not being recognized. I even put in a different hd. I even formatted the drive using one of my macs that I only have 9.2.2 on and installed a os on it and it still didn't work. The hard drive worked fine and the os with all of its components seemed to be fine. I know it's an older system but it's something that I can let the kids play on and not be concerned with losing any of my files.
    I appreciate any help
    Various Macs    
    Various Macs    
    Various Macs    

    Posted this in wrong area. I've reposted it in the right section. Sorry!

  • HELP. new hard drive not recognized

    HELP!
    guys, i badly need your help. i've been searching all over the internet and reading so many user groups already to search for answers to no avail.
    I bought a new Western Digital 160GB Scorpio SATA hard drive. I wanted to upgrade my Macbook which only has 80GB as of now.
    I cannot seem to install Mac OS X on it. Here's the problem:
    1. it is recognized as "Media" with 0 bytes capacity which I am really surprised why it's like that
    2. PARTITION: partition fails and i receive an error message saying that the "Device is not configured"
    3. ERASING: i also tried erasing it but it also fails; the message reads "The selected disk does not have enough capacity"
    i really don't know what seems to be the problem. i can't use it, can't even format it, not partition it.
    so now it's just sitting on my desk, useless. i want to use it badly though.
    can someone help me please? thanks.

    Hi Paoj
    You don't say if you have found that the new HD is Fat32 or not, so I will proceed assuming that it is FAT32. I will also proceed on the basis that there was nothing on the new drive already that you needed to keep or can't download.
    1) Open Disk Utility.
    2) Select your External Drive from the list presented
    3) Select the 'ERASE' tab then the "Mac OS Extended (Journaled)" option in the 'Volume Format:' box. In the box below, give the drive a name if you want to.
    No need to bother with the 'Options' button etc.
    4) Select "ERASE'
    This should rewrite your new drive in HFS+ (Journaled) format.
    Assuming the above has worked for you -
    The next step is optional, but careful consideration is recommended at this point in time because one can't change one's mind, say, months later.
    1) Still in Disk Utility, select the 'PARTITION' tab.
    2) Under 'Volume Scheme:" choose however many partitions (extra hard drives) you consider appropriate.
    For instance, I have an 500gb External Drive partitioned into two drives of about half that size. One I have for expansion and has a bootable version of Panther on it. The other is my backup drive.

  • External hard drive not recognized... help please.

    okay, well here is the story:
    my iBook G4 had its stock 30gb hard drive in it and it was running extremely low on space. so i figured i didn't want to carry around an external hard drive, therefore i would buy an internal hard drive an install it. so i purchased a new 2.5" 80gb hard drive and called up the local apple store. they told me that although it was under warranty, that it did not cover hard drive installation. so i looked it up online and found step by step instructions to install the hard drive. so after lots of hard work and many screws, i installed the new hard drive successfully... but i still had this perfect 30gb hard drive. i thought maybe to save a few bucks i could turn it into a usb external hard drive. i found an enclosure for the hard drive and a usb 2.0 cable and plugged it into my ibook. it was recognized and everything. i put some files on the external hard drive and transferred it to another mac. this is where the trouble started. i plugged the hard drive into a PowerMac G4, and it was not recognized... so i tried it on a different mac. this time on a PowerBook G4, but no luck. this issue has been troubling me for a few weeks. but then i tried it on a similar iBook G4... and it was recognized. but i don't know why it was only recognized only on the iBook G4 (not the same iBook G4 it was pulled out of) and no other macs.
    does anybody have any ideas what we can do to get this hard drive to be recognized by other macs?
    any of even the smallest ideas would be greatly appreciated.
    thanks,
    tyler
    iBook G4   Mac OS X (10.4.3)  

    I can walk you through formatting the hard drive:
    1. Hook it up to an iBook that recognizes it.
    2. Go into your Applications folder, then scroll down to Utilities. Open Utilities and scroll down a bit and you should see Disk Utility. Double-click.
    3. On the left side you should see your internal hard drive and your external one. Each hard drive will have a sub-catagory with the partition indented.
    4. Your external hard drive will probably be the second catagory. Click it.
    5. In the center-top you should see the tabs First Aid, Erase, Partition, RAID, and Restore. Click the Erase tab.
    6. You should see Volume Format: and then a drop down menu, and Name: and a text box. Type in the name you want the external hard drive to be named.
    7. In the drop down menu, select Mac OS Extended (Journaled).
    8. Then, simply click Erase, watch the progress and it should be good to go!!
    Hope I helped you out. Oh, and it might be the enclosure...and also what OS's? Since it's USB it is probably using a USB Mass Storage driver. Mac-wise, if formatting doesn't help, I would get a FireWire enclosure because FireWire is much faster than just USB 2.0. Oh, thats nother thing...Is the enclosure Hi-Speed USB? If it isn't, I would definitely get a FireWire one...If it is, the PowerMac G4 doesn't have Hi-Speed so you're not taking full advantage..Just some insight
    iBook G4   Mac OS X (10.4.3)   512 MB Ram, CD-RW Combo Drive, 40 Gig HD, bought in October of 2005...
    Message was edited by: Hilary_Rose

  • External USB Hard Drive not recognized on iMac HELP!!

    I am currently using a i5 iMac running Lion 10.7.5
    I have recently partitioned a Verbatim USB external hard drive and uploaded all my footage from a wedding. This was done with no problems and the QT videos could be opened from the hard drive.
    A few weeks later, the hard drive does not show up in my finder. BUT it is recognized in disk utility. Here is a screen shot;
    So first I ran "Verify" and it told me to repair disk. After clicking on Repair, I got this;
    It is giving me the error message "Invalid B-Tree node"
    Here is more info on the hard drive;
    Name : Hitachi HTS545032B9A300 Media
              Type :           Disk
              Partition Map Scheme :           Master Boot Record
              Disk Identifier :           disk1
              Media Name :           Hitachi HTS545032B9A300 Media
              Media Type :           Generic
              Connection Bus :           USB
              USB Serial Number :           091004B3066D
              Device Tree :           IODeviceTree:/PCI0@0/EHC2@1A,7
              Writable :           Yes
              Ejectable :           Yes
              Location :           External
              Total Capacity :           320.07 GB (320,072,933,376 Bytes)
              Disk Number :           1
              Partition Number :           0
              S.M.A.R.T. Status :           Not Supported
    Can someone give me a step by step on how to get the hard drive working again? It would mean the world to me as this footage is priceless and irreplaceable.
    OR can you refer me to someone (Geek Squad? Apple Store?) that might be able to help me out?
    Thanks in advance!

    The error message invalid b-tree node size indicates that the directory on the disk is corrupt. The way that it can be repaired is to reformat as disk utiltiy says.
    It is recommended that the data be backed up first before either of this solution are done.
    Since it is not be recognized by the sytem at all it does sound like you can back it up now.
    Do you have a backup?
    If you don't there is every chance you may lose all your data.
    You can check to see if a data recovery service can recover any data for you. If you go that route you are looking at spending $$$$
    Allan

  • Help needed - External mobile hard drive not recognized by my iMac

    Hi, i received a Freecom Mobile Drive XXS 250 GB USB 2.0 today, after plugging it into my iMac, i am finding that nothing is showing up, and it isn't being recognized at all.
    I've tried connecting it via all the USB ports, i have tried connecting it and disconnecting other cables (like speaker + printer cables) and it's not working. I'm not all that computer literate, but after scouring the internet for hours i understand the problem could be that my USB ports are 1.1 and a bus powered hard drive might not get the sufficient power from them?
    I have looked at the system requirements for the hard drive and my iMac apparently has all the requirements this needs to work. I have checked Disc Utility and the external hard drive isn't even showing up there. I thought i might have had to re-format the drive, but i checked and it is already FAT-32 so should be ok?
    Very puzzled, and am out of ideas on how to get this to work (need to transfer files quite urgently - want to upload some new software and don't want to risk losing the files on my internal hard drive, as my computer is getting about slow and unreliable also have the problem of my cd burner now being defunct for some reason, but thats unrelated to this hopefully)
    Has anyone got any ideas on how i could get this to show up on my computer? Any info will be much appreciated!
    Regards, coby x

    Hey coby,
    Well thanks for the star. Not sure I deserve it.
    i then tried connecting the drive to each USB port again, and voila! i have found one it works in. I guess my computer's ports must be a little worn.
    Hmm well try looking inside and see if there's some smutz in there, if the contacts are dirty or bent or worn.
    i was starting to think i would have to go out and get a USB hub to give it some more power.
    Is it powered off the USB? If so that actually might be a good idea since that puts a lot of strain on the connectors. Even if it's self powered it might be a good idea since it would take the strain off an obviously flakey USB.
    richard

  • Toshiba External Hard Drive not recognized by computer. Please help!

    I was wondering if anyone could help me. I have an external hard drive and it will not show up in "My computer" when I plug it in. I have tried other USB drives and other computers. I am starting to think it is a hardware issue but I don't want to lose hope. The blue light is coming on when you plug it in but it doesn't blink and there is no noise whatsoever. Is there anything I can do to fix this issue so that I can recover the information on it? Thanks in advance for any help. It is greatly appreciated.
    Additional information: I'm not sure how old this thing is but the model number is HDDR160E03X.

    Same problem: I can't see my Toshiba PH3100U-EXB (Gen 2) external hard drive when I plug it in. After awhile I get this error message (see attachment): USB Device Not Recognized. One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it. FOr assistance in solving this problem, click this message."
    When I click it, I get a list of USB ports and devices, with Unknown Device in bold face. No real information there.
    Yes, I ran Disk Management and the Toshiba did not show up when I plugged it in and hit Refresh.
    Does it make a difference that the last time I used the external hard drive, we were in Windows XP and now we're in Windows 7?
    Please help! It's not just the backing up I'm worried about...it's being able to retrieve files later!
    Thanks!
    Attachments:
    USB-NotRecognized.jpg ‏28 KB

  • External hard drives not recognized by imac

    I am a new Mac user and have been having lots of trouble getting my external hard drives to mount. I have a simpletech and a seagate external hard drive both NFTS formatted neither of which is recognized by my iMac. They don't show up on disk utility or system profiier under USB ports. They both work on my PC laptop and a friends iMac (OS 10.6.4) just fine. I have a card reader and flash drive that work perfectly on my iMac. Apple support orginally thought it might be the logic board so they replaced it. The new one is having the exact same problem. Does anyone have any idea what could possibly be the problem?? This is driving me insane.

    I'm having exactly the same problem with a new iMac purchased one week ago. I have two Maxtor drives and one WD, all firewire 400 drives, all of which mount briefly and then unmount and will not mount again. I am not new to Macs. The drives work fine on the older PowerPC Mac running 10.4.11. These drives contain my backups and aren't recognized by the new iMac. I cannot believe that 3 external drives are all going into failure mode at the same time since they were all purchased at different times and only used as backup drives, so they weren't on all of the time. Is there an incompatibility between 800 and 400?? I'm using a LaCie 800 to 400 firewire cable. Suggestions??

  • External Hard Drive Not Recognized In Vista?

    I have a Western Digital MyBook hard drive, 500 GB. I have my Time Machine backups un there as well as my iTunes music.
    However, whenever I am in Vista, it never shows up in the Explorer.
    Why is this happening?

    I am new to mac but also have fusion. I have the western digital ext hard drive and a back up genie to back up my fusion pc side and a seperate simpletech 1 tb ext hard drive configured for my mac. I also have a shared drive that i can save from side to side. With all this said i sometimes have the issue of not recognizing the western digital in my fusion pc side. Then all of sudden hours or a day later it will be there. It is not formatted for mac. Help, how do i get it recognized all the time.

Maybe you are looking for