Advanced monitoring and report feature on ACS5.1
Hi !
I would like to know where I can find documentation about the "Advanced Monitoring and Report" feature on ACS server version 5.1.0.44-3. I would like find information about the installation, benefit of this feature, and how to use advanced monitoring and report feature.
In ACS 5.0 there was a separate licensed feature that enabled additional monitoring and troubleshooting features such as alarms, thresholds and additonal reports. In ACS 5.1 this functionality is included by default as part of the base product
Similar Messages
-
Monitoring and Reporting on ACS 5.1 not working
Hello,
I have not managed to get the Monitoring to work on the ACS 5.1. This is an eval version. Advanced monitoring and reporting is installed on the ACS. This is my configuration on the Cisco Router
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 0 default start-stop group tacacs+
aaa accounting commands 1 default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting connection default start-stop group tacacs+
logging origin-id ip
logging facility syslog
logging source-interface GigabitEthernet1/1
logging host 1.1.1.1 transport udp port 20514
logging monitor informational
epm logging
On the ACS, when I open the dashboard --> ACS health -> I get Status not available.
Global Instance under Logging Categories been configured for local logging
ThanksThe view logprocessor is not running
ACS role: PRIMARY
Process 'database' running
Process 'management' running
Process 'runtime' running
Process 'adclient' running
Process 'view-database' running
Process 'view-jobmanager' running
Process 'view-alertmanager' running
Process 'view-collector' running
Process 'view-logprocessor' not monitored
Does anyone know how to start it??
Thanks -
Cisco Secure ACS 5.4/Monitoring and Report Viewer - SNMP Settings
Hello Everyone.
I hope this is the right forum for my question.
We just purchased 8 1121 ACS 5.4 appliances. I have some familiarity with the older 1113 and 1120 appliances running ACS 4.2. So I have a lot to learn.
Right now I'm trying to understand the Monitoring and Report Viewer System Configuration. I set the SNMP V2 read comm. string to the same string I configured from the CLI.
etc-labacsb1-1/admin# show runn | inc snmp
snmp-server contact "ACS1121;XXXXX"
snmp-server location "B1 Lab"
snmp-server community XXXXXX ro
1) It was not the same string as configured on CLI. Does setting this give me access to query more than system type or server type MIB objects.
2) Can you provide an example? (for example to query a switch - snmpwalk -v 1 -c XXXXXX hostname 1.3.6.1.4.1.9.9.43)
3) What is the MIB object tree OID (1.3.6.1.4.1.9.???) for these ACS appliances?
Thanks in advance.
Ray Westphal
EHIthat's correct. here is what we have in ACS 5.4 for snmp.
ACS 5.4 supports Simple Network Management Protocol (SNMP) to provide logging services. The SNMP agent provides read-only SNMPv1 and SNMPv2c support. The supported MIBs include:
•SNMPv2-MIB
•RFC1213-MIB (MIB II)
•IF-MIB
•IP-MIB
•TCP-MIB
•UDP-MIB
•CISCO-CDP-MIB
•ENTITY-MIB
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.4/device_support/sdt54.html#wp71020
~BR
Jatin Katyal
**Do rate helpful posts** -
Customizing the Monitoring and Report Viewer - ACS 5.2
Is there a way to modify the columns shown in the monitoring and reporting viewer so that I can see all of the relevant columns in one screen, similar to the ACS 4.x view? I would like to view things at a glance, rather than having to click into each item. Thank you for your help in advance.
that's correct. here is what we have in ACS 5.4 for snmp.
ACS 5.4 supports Simple Network Management Protocol (SNMP) to provide logging services. The SNMP agent provides read-only SNMPv1 and SNMPv2c support. The supported MIBs include:
•SNMPv2-MIB
•RFC1213-MIB (MIB II)
•IF-MIB
•IP-MIB
•TCP-MIB
•UDP-MIB
•CISCO-CDP-MIB
•ENTITY-MIB
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.4/device_support/sdt54.html#wp71020
~BR
Jatin Katyal
**Do rate helpful posts** -
ASK THE EXPERTS - WAAS MONITORING AND REPORTING
Welcome to the Cisco Networking Professionals Ask the Expert conversation. This is an opportunity to learn about Cisco Wide Area Application Services monitoring and reporting with Michael Holloway and Joe Merrill. Michael is an escalation support engineer in the Application Delivery Business Unit focusing on escalations to engineering related to the Cisco Wide Area Application Services (WAAS) product. He has worked with Cisco WAAS since its initial development, and with the first product beta.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
Joe Merrill is an escalation support engineer in the Application Delivery Business Unit focusing on escalations to engineering related to the Cisco Wide Area Application Services (WAAS) product. He has worked with Cisco WAAS since its initial development, and with the first product beta.
Remember to use the rating system to let Michael and Joe know if you have received an adequate response.
Michael and Joe might not be able to answer each question due to the volume expected during this event. Our moderators will post many of the unanswered questions in other discussion forums shortly after the event. This event lasts through August 27, 2010. Visit this forum often to view responses to your questions and the questions of other community members.Very good questions. Let me try and take them one at a time. Some of the answers you will likely find in the CM GUI help (upper-left corner is the Help button), or in the online documentation. But let's add a little more color and detail.
1)When we pull bandwidth Optimization report, on Y-Axis the graphs says Effective Capacity .What is Effective Capacity?
Basically, the "effective increased bandwidth capacity" is telling you how much additional WAN bandwidth you've gained because of the optimization. It will chart somewhere between 1 times and 100 times. Typically it charts all traffic, though you can configure it to chart traffic for specific Applications.
The CDM online help gives the formulas used to chart the graph:
Effective WAN Capacity = 1 / (1-% Reduction Excluding Pass-Through)
% Reduction Excluding Pass-Through = (Original Excluding Pass-Through - Optimized) / (Original Excluding Pass-Through)
2)what is reduction % excluding and including passthrough
Looking at the formulas given above might help you understand. The one is a reduction ratio compared to only the original traffic that is optimized. The other is a reduction ratio compared to all original traffic, whether it is optimized or not. So, if you want to know what kind of optimization you are getting for the traffic that you configured to have optimized, look at the "excluding pass-through" numbers. If you want to know the positive effect that optimization is having on your full traffic load, take a look at the "including pass-through" numbers.
3)What is effectivity capacity including and excluding passthrough ?
The effective capacity is what kind of throughput you can potentially realize on the WAN -- assuming you would fill it to 100% capacity -- because of the level of optimization you are seeing. The "including" numbers show you the effect of optimization compared to all the traffic passing through the WAE whether it is optimized or not. The "excluding" numbers show the effect of optimization compared only to the traffic that is receiving optimizations.
4)With the help of which report, we can show the customer that the file download which took 10 mins in first attempt, is downloaded in 10secons in next attempt?
This one is a little trickier. The reports are much broader than a single connection. They are for all traffic, or for traffic that matches specific defined Applications. You could create a separate Application and matching classifiers for the client and/or server IP addresses and/or ports, run the test, then configure the charts to only show you the data for that Application. By default, statistics for an Application aren’t charted unless you check the "Enable Statistics" box when defining/editing the Application.
5)How to show that the bandwidth utilization has decreased by which %.
You want to look at the % reduction numbers you asked about in #2 above.
6)Which report says that the applications have become this much time faster?
These questions are normally put forwarded by many customers ? Can you please help me with your expertise answer ?
This is probably the hardest question to answer.
"Faster" isn't always easy to define. You are probably talking about user experience rather than statistics found in a network device. What determines that experience? A web page fully populating with all the pictures? A CIFS-based application that saves a file? A custom application that collects data from different servers over different protocols to perform some operation? Much of that is subjective and based on multiple individual requests, sometimes over different protocols.
What we can provide are statistics to show the effect of WAN optimization and application acceleration for specific types of traffic. We can't show you that displaying a web page is N times faster with WAAS, because we don't know which of all the many HTTP requests that are made are specific to the user experience. But we can show that each of the requests received so much overall optimization, so much optimization from DRE, so much optimization from LZ, so much added benefit from HTTP acceleration.
What you would probably do is collect some base-line timings for performing certain user activities, then perform the same operations both cold (first pass) and warm (subsequent passes). Back up those timing numbers with reports from the CM GUI, and perhaps even the "show statistics connection connection-id ". Which reports to use? Start with those Optimization and Acceleration reports. Those are the reports we expect will give the most complete/accurate pictures of the benefit of WAAS. You can also create and even schedule custom reports as needed. -
IPS event monitor and reports not working
Dear after upgrading my IPS from E3 to E4 the event monitor and reports not working, can you please advice my to solve this issues
Hi All,
Filter settings below:
The filter works partially as I don't get alerts on the IPS itself.
Firewall LOG:
4 Feb 14 2014 15:33:22 39715 514 IPS requested to drop UDP packet from SOURCE_VLAN_NUMBER:/39715 to DESTINATION_VLAN_NUMBER:/514
IPS LOG (when enabled):
evIdsAlert: eventId=1352793300955167909 vendor=Cisco severity=low
originator:
hostId: SSM02
appName: sensorApp
appInstanceId: 1192
time: Feb 14, 2014 15:33:22 UTC offset=0 timeZone=GMT00:00
signature: description=IP Fragment Too Small id=1206 version=S212 type=anomaly created=20030801
subsigId: 0
sigDetails: Too many small IP fragments in datagram
interfaceGroup: vs0
vlan: 0
participants:
attacker:
addr: 172.x.x.x locality=OUT
port: 39715
target:
addr: x.x.x.x locality=OUT
port: 514
os: idSource=unknown type=unknown relevance=relevant
alertDetails: InterfaceAttributes: context="single_vf" physical="Unknown" backplane="GigabitEthernet0/1" ;
riskRatingValue: 50 targetValueRating=medium attackRelevanceRating=relevant
threatRatingValue: 50
interface: GigabitEthernet0/1 context=single_vf physical=Unknown backplane=GigabitEthernet0/1
protocol: udp
Our next step is to make a service policy exception on the firewall itself. We are also considering reloading the IPS device or at least the analysis engine.
Thanks for all your help so far. Any more suggestions are most welcome. I'll keep you up to date.
Regards
Mariusz -
Forms and Reports Feature/Benefit Demo
Hi,
I downloaded a sample code, Forms and Reports Feature/Benefit Demo, from OTN sample code site. During the installation it says that my system (NT 4.0 Workstation with Oracle8 Server Release 8.0.6) does not have Oracle WebDB Listener. Where can I download it? Can I install it on a NT workstation (not a web server)? If not, is there other way to make that demo working? Thanks.
hvThat depends on what you mean by clustering and exactly what version you are talking about.
-
GroupWise 2014: advanced querying and reporting
Hi,
GroupWise 2014 came with the announcement that incorporated new advanced querying and reporting capabilites, but I'm unable to find them.
Does anyone know if it incorporates something in this regard, and if so, where to find it?
Regards
Jose Luisjlrodriguez wrote:
> GroupWise 2014 came with the announcement that incorporated new
> advanced querying and reporting capabilites, but I'm unable to find
> them.
>
> Does anyone know if it incorporates something in this regard, and if
> so, where to find it?
In the 2014 admin console there is a global object search. In
addition, when managing users there is comprehensive searching
capability to find specific users based on many different attributes.
It's also possible to query GW directly using the REST interface and
bypass the admin console altogether.
Your world is on the move. http://www.novell.com/mobility/
Supercharge your IT knowledge. http://www.novell.com/techtalks/ -
Getting no file found under the given path- VNX-Family Monitoring and Reporting
Server- Windows-2012 R2
Using v21 of setup-vnx-mr-v21-win64
Using NAVCLI-Win-32-x86-en_US-7.33.6.0.96-1
Installed VNX-Family Monitoring and Reporting w/o any issues. Set user permissions.getting
Attempting to add VNX5400
I am using direct IP address: 10.X.X.X, Getting no file found under the given path error.
Any suggestions?
An using correct permissions
Thanks
This topic first appeared in the Spiceworks CommunityServer- Windows-2012 R2
Using v21 of setup-vnx-mr-v21-win64
Using NAVCLI-Win-32-x86-en_US-7.33.6.0.96-1
Installed VNX-Family Monitoring and Reporting w/o any issues. Set user permissions.getting
Attempting to add VNX5400
I am using direct IP address: 10.X.X.X, Getting no file found under the given path error.
Any suggestions?
An using correct permissions
Thanks
This topic first appeared in the Spiceworks Community -
Cisco ACS 5.2 (esx 4 vm) and Monitoring and Reports failure
I am evaling the Cisco ACS 5.2 Virtual Appliance on ESX4 and everything is working fine except for the "Monitoring and Reports" no matter what browser I try, it just keeps loading new tabs of the welcome screen, in the case of some browser versions it does this and does not stop.
I have tried the following browsers on Win7 Pro: IE 8, Firefox 4, Firefox 3, Chrome 12.
I have tried the following browsers on MacOS 10.6: FireFox 4, Safari 5.0.5
In Safari 5.0.5 it calls up one new window, but doesn't load anything in the right hand frame.
This is a fresh install, with an eval license. I am rather annoyed that it doesn't work out of the box, especially when there was not documentation that mentioned that anything needed to be setup for this to work after initial install, unless I missed something.
I installed the VM with the base 5.0.26 ISO and then applied patches 5.0.26-1 through 5.0.26-5.
Can anyone provide any help on this?I am evaling the Cisco ACS 5.2 Virtual Appliance on ESX4 and everything is working fine except for the "Monitoring and Reports" no matter what browser I try, it just keeps loading new tabs of the welcome screen, in the case of some browser versions it does this and does not stop.
I have tried the following browsers on Win7 Pro: IE 8, Firefox 4, Firefox 3, Chrome 12.
I have tried the following browsers on MacOS 10.6: FireFox 4, Safari 5.0.5
In Safari 5.0.5 it calls up one new window, but doesn't load anything in the right hand frame.
This is a fresh install, with an eval license. I am rather annoyed that it doesn't work out of the box, especially when there was not documentation that mentioned that anything needed to be setup for this to work after initial install, unless I missed something.
I installed the VM with the base 5.0.26 ISO and then applied patches 5.0.26-1 through 5.0.26-5.
Can anyone provide any help on this? -
Monitoring and recording feature not working in UCCX
Hi,
The recording and monitoring option is not working in the new UCCX setup I have installed.I have configured following things for desktop monitoring as per the document
1)Checked that IP Phones are diasy chained and speakers of Supervisor's PC is working,NIC card of agent's and supervisor desktops are compatible
2)In web CDA P phones to be monitored have been configured
3)In CCM configured the phone for "Span to PC port" as enabled also configured "Advertise G.722 codec" as disabled
4)Ran postinstall.exe on agents system and checked if correct NIC adapter is being used for monitoring
5)Checked the NIC binding order in UCCX server and that is correct
I noticed one thing that "services" in both CAD and CSD are showing as "partial services" and they are monitoring and recording services only.Hence is this problem related to these services? How do i correct the recording and monitoring issue?
Regards
Amit/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
I would first recycle the VOIP Monitoring Service on both node if this is HA. This will not affect calls or call processing.
In addition, you stated you ran post install on the clients desktop but have you ran post install on the server itself?
In the desktop Administrator, what server is selected to be the default VOIP Monitor server?
Jason M. Hutchinson -
Cisco ISE 1.2 monitoring and Reporting
Hi Ali
We're trying to determine how many addtional Base licenses we have to purchase in order to be compliant in our Cisco ISE 1.2 platforms (already have 1500 CISE 1.2 Base licenses in production).
Is there any means to monitoring (e.g SNMP polling) and get scheduled reports showing the numbers of used licenses for a period ?
looking forward to heard you back -
Monitoring and Reporting with JMX?
We need a good way to monitor JMX objects. From A Network Operations type perspective. Goal being to work with our dev team to dial down values associated with escalations to fix production issues. Currently our plan is to upgrade to sitescope 8.6 (with JMX Support). This option will cost us alot of money. Enough that we are researching other options.
What is the best way to monitor JMX objects with alerts being sent? Are there any options outside sitescope that are reliable and scaleable? Is there a way for JMX events to write to the event log on a W2K3 server, or are there any custom connector services into MOM (microsoft Operations Manager <didn't think so...>) . Please let me know any recommendations you might have. right now our only way is cutom developer work or sitescope.....
Thank You in advance.anyone?
-
Database monitoring and report
Hi all, I'd like to start monitoring the customer's database.
I need a tool to monitor database's performances and I also need to run day by day a series of queries that produce control reports.
I'd like the tool alerts me by email if something goes wrong.
Does anyone could indicate me tools that work in this way? Any suggestions?
TIA.
Alder MoriggiDBConsole comes with Oracle DB. Though some reports (AWR) should be licensed separately.
GridControl installed and licensed separately.
You can take a look at Nagios that is a generic monitoring framework (free).
You can find in Net several plugins for Oracle for it.
Also you can write your own script/plugin using Shell or C or Perl or whatever language that can produce a standard output and exit number. -
ACS 5.1 shows no logged events in Monitoring and Reports
Hello
I have a Cisco ACS 5.1 virtual appliance which has been working fine, I have however just discovered that it is now unable to provide me with any logs.
TACACS authentication is still working without any issues, the only problem I have is viewing the logs.
Many Thanks in advance for the help.
Georgeeverything is running. I have tried restarting some of the services, however I have had no joy.
ACS role: PRIMARY
Process 'database' running
Process 'management' running
Process 'runtime' running
Process 'view-database' running
Process 'view-jobmanager' running
Process 'view-alertmanager' running
Process 'view-collector' running
Process 'view-logprocessor' running
Maybe you are looking for
-
How to search a maximum in range (determined by a value in another cell)?
I'm trying to find the maximum and minimum in a range of cells. I've determined the start cell and end cell in Table 1 for each search range, but I can't get it to fit in a formula. TABLE 1 1 --- 105 2 --- 75 3 --- 20 4 --- 74 5 --- 124 6 --- 100 7 -
-
I have programmed iCal and Address book to sync via MobileMe. The info I type in iCal on the MacBook Pro get updated on the iPad, but not the other way around. Any hints?
-
Create view structure based on table
Hi, I've got two tables one spec table containing a table num, column name and column length. For example: Table num Column name Column length 1 client_id 8 1 client_n
-
SYS.DBMS_CDC_PUBLISH errors during create table command
While trying to create tables I am getting the following errors. @dv001_bld_emp_profile.sql create table emp_profile_tbl ( ERROR at line 1: ORA-00604: error occurred at recursive SQL level 1 ORA-01422: exact fetch returns more than requested number o
-
Connecting Oracle 8i - OracleDeveloperSuite10g
Hi I have just downloaded OracleDeveloperSuite10gDisk1.exe and OracleDeveloperSuite10gDisk2.exe from oracle site. I have already installed Oracle 8i on my machine. Now After installing OracleDeveloperSuite10g, I have to develop my application with th