Advice for a Home Wireless Network

Hi, I am looking for some guidance on the best way to set up a wireless network in my home.  I am not wired for ethernet and my Internet access is through Comcast Cable.  The main issue I have is that I must place my wireless router in the basement near the wiring closet because the cable modem is also required to be there (DirecTV provides my TV programming so the coax cable throughout the house is used for that). 
Placing the wireless router in the basement works ok for access from the basement or first floor but the signal is very weak from second floor and backyard.  I am also limited to using the WRTP54G Wireless Router (Vonage version) for the basement router but if there is anyway to use something else as the main router while just using this as the phone router, I would jump at that since I have found this model to be somewhat unreliable.
Ideally, I would like to take advantage of the increased range and speed of the 802.11n format.  I have been reading on here about different ways to link wireless APs together but I'm not totally clear on what equipment is necessary.  My main goal is to be able to access the internet from the 2nd floor and also from the backyard, as far as 200 ft away.  I can place wireless equipment basically anywhere inside.  Cost is important but is a secondary consideration to functionality.
Any suggestions would be most appreciated!!

You can trust WRT610N as it will give you the desired range...

Similar Messages

  • Do I really need an Airport device for my home wireless network?

    Hi Apple Users,
    I am seriously considering purchasing my very first Apple computer: a MacBook Pro to be precise.  I'm a very experienced Windows PC user - was a Microsoft Windows & Office -based Help Desk Analyst at my company for 13 years till I was laid off last year.  So I know my way around Microsoft Windows computers, Windows LANs, wireless networking & servers, security, etc.  I currently own a Dell Precision laptop running Windows 7 - have had it for 3 years with no problems (yet - knock on wood).  I have a cable modem with a Motorola SBG900 wireless router / gateway with hardware firewall enabled. Everything is secure, only certain ports are open, etc.
    If I buy this MacBook Pro, get it delivered, turn it on, create my logon, etc. will it automatically work with my current wireless router / gateway after going thru the set-up procedure to connect to my network & the internet?   Or do I absolutely have to purchase one of the Airport adapters in order for the Mac to talk to the router? 
    Thank you for being patient with a newbie Apple / Mac User wannabe.  I'm very excited!
    Kim

    Thank you Rysz, but (if you scroll up & read my original post you will discover) I don't own my new MacBook Pro...yet!  I'm just researching ahead of time to help me make the decision.  The customized MBP I have saved in my cart is over $3000 (incl the 3-yr support plan).  So it's going to take me a little bit of research before I decide or before I can really justify the purchase.
    I just wanted to be prepared for all the inevitable technical / learning-curve headaches that I will experience IF I take the plunge.   And as everyone has experienced, when you're new to and making your first purchase of a different technology, and you don't know what to expect about a purchase, you ultimately get it home, set it up and find it didn't come with all the necessary interface devices, converters or cables, etc.  And of course the online purchase procedure wizard doesn't tell you or ask you what else you will need if you want to perform a specific task. 
    But I'm sure (if) once I do make the purchase, I will definitely be back here to pick everyone's brains!  These communities are fantastic.   Thanks again!

  • TS1398 Password for my home wireless network

    My Linskys is encryped, what is the password to connet to safari?

    There's no way anyone here would know that. You would have to consult the documentation for your router or look at the settings in the router.
    Regards.

  • Recently I was working on my home Network and lost my Password for my Home wireless connection. After many attempts, I remembered the password and was able to get in. Now the MacBook Pro only works at home on a Hard wire connection. I have an additional 9

    Recently I was working on my home Network and lost myPassword for my Home wireless connection. After many attempts, I remembered thepassword and was able to get in. Now the MacBook Pro only works at home on aHard wire connection. I have an additional 9 devices on the same network, allare functioning properly. The Air connection works fine at any other Networksout side the Home connection. I did a PRAM reset, deleted the Network profileand rebuilt in System Preferences. Still unable to connect wireless on Homenetwork. Any Ideas?

    I seem to have fixed it by putting <div  class="clearfloat"></div> after the navigation bar?

  • MacBook Pro Can't find home wireless network

    I've been having some issues getting my macbook pro, running OS 10.7.5, to find my home wireless network. The network doesn't show up when it searches automatically, and when I type the network name in to find it manually, it says no network found. The computer connects to all other networks and finds then with no issues, and other MacBooks are able to find my home network and connect to it again with no issues.
    The computer used to be able to find the network, and then it just stopped working. I have tried all the standard fixes, resetting the router, computer, PRAM, forgetting the network, deleting the key from keychain, but nothing seems to work. I tried googling the issue, but wasn't able to find a problem similar to the one I have.
    Any advice would be greatly appreciated.
    Thanks

    Still having problems with this.
    I have upgraded to Mavericks, hoping that the problem would be fixed, but it hasn't. I still get all networks completely disappearing - even if I search for them they are not found.
    But I reboot the computer and it works! But when I am in OS or Bootcamp mode and put the Mac to sleep, it does not see the networks again! I have to reboot the computer for it to work.
    I have even got a new router which can receive the b,g and n signals etc. as I was told by a Mac techie here that Macs 'look' for the n signal but can also work with the b and g signals and THAT maybe my old router only transmits b and g or something like that .
    This, to me, sounds like a Mac software problem. I had a similar problem on a previous Mac on my "old router" and a totally different router in a different country's telephone system.
    I now have the same problem with a new MBP on a new router!
    Maz

  • IPad won't connect to home wireless network

    Got my iPad for Christmas and it has worked perfectly until tonight. Out of the blue it wasn't connected to my home wireless network. I reset the modem, powered the iPad off and on again, reset the network settings and reset all settings. No luck, it just keeps searching all of the laptops in the house work just fine ??

    Hi HugBeth - Welcome to the forums.
    Notice the links other posters provided above? Follow those links and then come back and thank those folks that took the time to pass along problem-solving advice.
    Pam, you might wish to checkout these resources as well:
    I prefer this list of solution oriented suggestions as a starting point: http://tinyurl.com/3yorao9
    You'll also find an ongoing discussion in this forum entitled: "Weak Wifi" I have also included the link for you- http://tinyurl.com/2ctu39q It contains additional problem-solving steps undertaken by users when they found the standard solutions for missing & weak connections did not apply to them.
    Good luck.

  • Home Wireless Network & Backup

    Hello-
    Can anyone suggest some helpful resources (e.g., websites) for configuring a home wireless network where different users (e.g., family members) can backup their files via the network instead of having to physically connect their computers to a separate, external drive? Thanks much.

    The new Apple Airport Extreme wireless router provides for this - connecting an external USB drive to the router for saving data and/or for backup purposes by anyone with access to the wireless network.
    http://docs.info.apple.com/article.html?path=Airport/5.0/en/ap2108.html

  • Home wireless network trouble

    I got a new wireless router, Netgear WPN824 from Newegg, a refurbished product. I set up a home wireless network using the online manual on the Netgear website. The router works well for the wired setup. But I could not connect to wireless.
    My wireless network shows up on the list of available wireless networks. I can connect to other wireless networks such as that of my neighbour's. I tried connecting to my network using both unsecured and secure WEP / WPA modes. Except once, I could never connect. That one time, as soon as I could connect and verify that I was indeed connected I thought the problem was resolved and so shutdown my system to see if i could connect again - alas, same trouble again. I use NetworkManager to connect, and here's the output for two networks - jaydoc which is my home network, and linksys, that of my neighbour's to which i can always connect.
    <info> Activation (wlan0) starting connection 'Auto jaydoc'
    Feb 26 02:37:04 Sarvam NetworkManager: <info> (wlan0): device state change: 3 -> 4 (reason 0)
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
    Feb 26 02:37:04 Sarvam NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0)
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Activation (wlan0/wireless): connection 'Auto jaydoc' requires no security. No secrets needed.
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Config: added 'ssid' value 'jaydoc'
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Config: added 'scan_ssid' value '1'
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Config: added 'key_mgmt' value 'NONE'
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
    Feb 26 02:37:04 Sarvam NetworkManager: <info> Config: set interface ap_scan to 1
    Feb 26 02:37:04 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning
    Feb 26 02:37:05 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating
    Feb 26 02:37:05 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: associating -> associated
    Feb 26 02:37:05 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: associated -> completed
    Feb 26 02:37:05 Sarvam NetworkManager: <info> Activation (wlan0/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'jaydoc'.
    Feb 26 02:37:05 Sarvam NetworkManager: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) scheduled.
    Feb 26 02:37:05 Sarvam NetworkManager: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) started...
    Feb 26 02:37:05 Sarvam NetworkManager: <info> (wlan0): device state change: 5 -> 7 (reason 0)
    Feb 26 02:37:05 Sarvam NetworkManager: <info> Activation (wlan0) Beginning DHCP transaction (timeout in 45 seconds)
    Feb 26 02:37:05 Sarvam NetworkManager: <info> dhcpcd started with pid 2428
    Feb 26 02:37:05 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Get) scheduled...
    Feb 26 02:37:05 Sarvam NetworkManager: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) complete.
    Feb 26 02:37:05 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Get) started...
    Feb 26 02:37:05 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Get) complete.
    Feb 26 02:37:05 Sarvam dhcpcd: version 5.1.5 starting
    Feb 26 02:37:05 Sarvam NetworkManager: <info> DHCP: device wlan0 state changed normal exit -> preinit
    Feb 26 02:37:05 Sarvam dhcpcd: wlan0: broadcasting for a lease
    Feb 26 02:37:51 Sarvam NetworkManager: <info> (wlan0): DHCP transaction took too long, stopping it.
    Feb 26 02:37:51 Sarvam dhcpcd: received SIGTERM, stopping
    Feb 26 02:37:51 Sarvam dhcpcd: wlan0: removing interface
    Feb 26 02:37:51 Sarvam NetworkManager: <info> (wlan0): canceled DHCP transaction, dhcp client pid 2428
    Feb 26 02:37:51 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) scheduled...
    Feb 26 02:37:51 Sarvam NetworkManager: <WARN> nm_dhcp_manager_handle_event(): Received DHCP event from unexpected PID 2428 (expected 0)
    Feb 26 02:37:51 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) started...
    Feb 26 02:37:51 Sarvam NetworkManager: <info> (wlan0): device state change: 7 -> 9 (reason 5)
    Feb 26 02:37:51 Sarvam NetworkManager: <info> Activation (wlan0) failed for access point (jaydoc)
    Feb 26 02:37:51 Sarvam NetworkManager: <info> Marking connection 'Auto jaydoc' invalid.
    Feb 26 02:37:51 Sarvam NetworkManager: <info> Activation (wlan0) failed.
    Feb 26 02:37:51 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) complete.
    Feb 26 02:37:51 Sarvam NetworkManager: <info> (wlan0): device state change: 9 -> 3 (reason 0)
    Feb 26 02:37:51 Sarvam NetworkManager: <info> (wlan0): deactivating device (reason: 0).
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Activation (wlan0) starting connection 'Auto linksys'
    Feb 26 02:39:08 Sarvam NetworkManager: <info> (wlan0): device state change: 3 -> 4 (reason 0)
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
    Feb 26 02:39:08 Sarvam NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0)
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Activation (wlan0/wireless): connection 'Auto linksys' requires no security. No secrets needed.
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Config: added 'ssid' value 'linksys'
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Config: added 'scan_ssid' value '1'
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Config: added 'key_mgmt' value 'NONE'
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
    Feb 26 02:39:08 Sarvam NetworkManager: <info> Config: set interface ap_scan to 1
    Feb 26 02:39:08 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning
    Feb 26 02:39:09 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating
    Feb 26 02:39:09 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: associating -> associated
    Feb 26 02:39:09 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: associated -> completed
    Feb 26 02:39:09 Sarvam NetworkManager: <info> Activation (wlan0/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'linksys'.
    Feb 26 02:39:09 Sarvam NetworkManager: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) scheduled.
    Feb 26 02:39:09 Sarvam NetworkManager: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) started...
    Feb 26 02:39:09 Sarvam NetworkManager: <info> (wlan0): device state change: 5 -> 7 (reason 0)
    Feb 26 02:39:09 Sarvam NetworkManager: <info> Activation (wlan0) Beginning DHCP transaction (timeout in 45 seconds)
    Feb 26 02:39:09 Sarvam NetworkManager: <info> dhcpcd started with pid 2444
    Feb 26 02:39:09 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Get) scheduled...
    Feb 26 02:39:09 Sarvam NetworkManager: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) complete.
    Feb 26 02:39:09 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Get) started...
    Feb 26 02:39:09 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Get) complete.
    Feb 26 02:39:09 Sarvam dhcpcd: version 5.1.5 starting
    Feb 26 02:39:09 Sarvam NetworkManager: <info> DHCP: device wlan0 state changed normal exit -> preinit
    Feb 26 02:39:09 Sarvam dhcpcd: wlan0: broadcasting for a lease
    Feb 26 02:39:17 Sarvam dhcpcd: wlan0: offered 192.168.1.115 from 192.168.1.1
    Feb 26 02:39:20 Sarvam dhcpcd: wlan0: acknowledged 192.168.1.115 from 192.168.1.1
    Feb 26 02:39:20 Sarvam dhcpcd: wlan0: checking for 192.168.1.115
    Feb 26 02:39:25 Sarvam dhcpcd: wlan0: leased 192.168.1.115 for 86400 seconds
    Feb 26 02:39:25 Sarvam NetworkManager: <info> DHCP: device wlan0 state changed preinit -> bound
    Feb 26 02:39:25 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Get) scheduled...
    Feb 26 02:39:25 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Get) started...
    Feb 26 02:39:25 Sarvam NetworkManager: <info> address 192.168.1.115
    Feb 26 02:39:25 Sarvam NetworkManager: <info> prefix 24 (255.255.255.0)
    Feb 26 02:39:25 Sarvam NetworkManager: <info> gateway 192.168.1.1
    Feb 26 02:39:25 Sarvam NetworkManager: <info> nameserver '167.206.254.2'
    Feb 26 02:39:25 Sarvam NetworkManager: <info> nameserver '167.206.254.1'
    Feb 26 02:39:25 Sarvam NetworkManager: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) scheduled...
    Feb 26 02:39:25 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Get) complete.
    Feb 26 02:39:25 Sarvam NetworkManager: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) started...
    Feb 26 02:39:26 Sarvam NetworkManager: <info> (wlan0): device state change: 7 -> 8 (reason 0)
    Feb 26 02:39:26 Sarvam NetworkManager: <debug> [1267169966.595494] periodic_update(): Roamed from BSSID 00:1D:7E:4E:C1:D7 (linksys) to 00:13:10:43:D7:DE (linksys)
    Feb 26 02:39:26 Sarvam NetworkManager: <info> Policy set 'Auto linksys' (wlan0) as default for routing and DNS.
    Feb 26 02:39:26 Sarvam NetworkManager: <info> Activation (wlan0) successful, device activated.
    Feb 26 02:39:26 Sarvam NetworkManager: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) complete.
    Is the wireless router i got a dud, being refurbished i took my chances and maybe i wasn't so lucky..! Or is it something wrong in my network settings..? I tried shutting down everything and then turning the modem, then the router and finally the PC without the ethernet cable connected. Still I am unable to connect.
    Any help is deeply appreciated. I am a total newbie in networking...!
    Last edited by jaydoc (2010-02-26 07:57:15)

    Router Status
    Hardware Version WPN824v3
    Firmware Version V1.0.7_1.0.8NA
    Internet Port
    MAC Address 00:1E:68:12:EB:1C
    IP Address [i]edited[/i]
    DHCP DHCP Client
    IP Subnet Mask 255.255.252.0
    Domain Name Server 167.206.254.2
    167.206.254.1
    LAN Port
    MAC Address 00:1F:33:FF:97:FF
    IP Address 192.168.1.1
    DHCP ON
    IP Subnet Mask 255.255.255.0
    Wireless Port
    Name (SSID) jaydoc
    Region United States
    Channel 1
    Mode b and g
    Wireless AP ON
    Broadcast Name ON
    that is what my router status is at the moment. and I am able to connect to the wired network using the router. However I still cannot connect wireless. I did not see any settings in the wireless settings page of the router that ask for DHCP server names/addresses. This is the current logfile output
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Activation (wlan0) starting connection 'Auto jaydoc'
    Feb 26 08:30:36 Sarvam NetworkManager: <info> (wlan0): device state change: 3 -> 4 (reason 0)
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled...
    Feb 26 08:30:36 Sarvam NetworkManager: <WARN> nm_dhcp_manager_handle_event(): Received DHCP event from unexpected PID 2548 (expected 0)
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started...
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled...
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete.
    Feb 26 08:30:36 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: completed -> disconnected
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting...
    Feb 26 08:30:36 Sarvam NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0)
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Activation (wlan0/wireless): connection 'Auto jaydoc' requires no security. No secrets needed.
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Config: added 'ssid' value 'jaydoc'
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Config: added 'scan_ssid' value '1'
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Config: added 'key_mgmt' value 'NONE'
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete.
    Feb 26 08:30:36 Sarvam NetworkManager: <info> Config: set interface ap_scan to 1
    Feb 26 08:30:36 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning
    Feb 26 08:30:37 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating
    Feb 26 08:30:38 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: associating -> associated
    Feb 26 08:30:38 Sarvam NetworkManager: <info> (wlan0): supplicant connection state: associated -> completed
    Feb 26 08:30:38 Sarvam NetworkManager: <info> Activation (wlan0/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'jaydoc'.
    Feb 26 08:30:38 Sarvam NetworkManager: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) scheduled.
    Feb 26 08:30:38 Sarvam NetworkManager: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) started...
    Feb 26 08:30:38 Sarvam NetworkManager: <info> (wlan0): device state change: 5 -> 7 (reason 0)
    Feb 26 08:30:38 Sarvam NetworkManager: <info> Activation (wlan0) Beginning DHCP transaction (timeout in 45 seconds)
    Feb 26 08:30:38 Sarvam NetworkManager: <info> dhcpcd started with pid 2730
    Feb 26 08:30:38 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Get) scheduled...
    Feb 26 08:30:38 Sarvam NetworkManager: <info> Activation (wlan0) Stage 3 of 5 (IP Configure Start) complete.
    Feb 26 08:30:38 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Get) started...
    Feb 26 08:30:38 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Get) complete.
    Feb 26 08:30:38 Sarvam dhcpcd: version 5.1.5 starting
    Feb 26 08:30:38 Sarvam dhcpcd: wlan0: rebinding lease of 192.168.1.115
    Feb 26 08:30:38 Sarvam NetworkManager: <info> DHCP: device wlan0 state changed normal exit -> preinit
    Feb 26 08:30:48 Sarvam dhcpcd: wlan0: broadcasting for a lease
    Feb 26 08:31:23 Sarvam NetworkManager: <info> (wlan0): DHCP transaction took too long, stopping it.
    Feb 26 08:31:23 Sarvam dhcpcd: received SIGTERM, stopping
    Feb 26 08:31:23 Sarvam dhcpcd: wlan0: removing interface
    Feb 26 08:31:23 Sarvam NetworkManager: <info> (wlan0): canceled DHCP transaction, dhcp client pid 2730
    Feb 26 08:31:23 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) scheduled...
    Feb 26 08:31:23 Sarvam NetworkManager: <WARN> nm_dhcp_manager_handle_event(): Received DHCP event from unexpected PID 2730 (expected 0)
    Feb 26 08:31:23 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) started...
    Feb 26 08:31:23 Sarvam NetworkManager: <info> (wlan0): device state change: 7 -> 9 (reason 5)
    Feb 26 08:31:23 Sarvam NetworkManager: <info> Activation (wlan0) failed for access point (jaydoc)
    Feb 26 08:31:23 Sarvam NetworkManager: <info> Marking connection 'Auto jaydoc' invalid.
    Feb 26 08:31:23 Sarvam NetworkManager: <info> Activation (wlan0) failed.
    Feb 26 08:31:23 Sarvam NetworkManager: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Timeout) complete.
    So if its still a DHCP problem, it seems to be affecting only the wireless part. How can I make wireless use the same DHCP servers as the wired..? Or is there something else wrong here..?

  • Home wireless network in China using Airport Express ?

    I am going to be living in China with my Macbook. I will be bringing my Airport Express with me.
    I would like to know whether it is appropriate to connect up my Airport Express to a Chinese cable modem to obtain wireless internet access at home.
    Or is it a very different system used in China for home wireless network.

    Many, but not all of the same wireless channels in the US are allowed in China. See this Wikipedia Document for some information.
    As to whether you will connect using ethernet or PPPoE, etc., that will depend on the provider that you choose.

  • I have 2 macs and 2 PC laptops in my home wireless network.  Can I use the Airport/Time Capsule hard drive to back up all 4 machines?  I know that I will have to use different back up software on the PCs, but is it possible over the wireless network?

    I have 2 macs and 2 PC (Windows 7) laptops in my home wireless network. (The iMac is hardwired via ethernet to the Airport/Time Capsule; the others are wireless connections using Airport).  I want to use the hard disk drive in the Time Capsule as a network backup drive for all 4 computers.  Is this possible?  Could someone help me by telling me how to configure it?  I know I will have to use different backup software in the 2 Windows 7 Laptops?  Do I need to use the Windows backup software, or can I use a third party program like Acronis True Image?  Thanks in advance for the help

    It is your fault, pondini.. all your fault.
    I read of all the things that go wrong restoring Time Machine backups.. particularly stupid things like mail, photo libraries don't go back.. etc. And looking through the incredible number of issues people have here, when their Mac finally takes a dive how hard it is to restore.
    I restored a test hard disk from a TC.. and it takes ages and ages to even make up its mind to start.
    I worked in computer support for ages, but not Macs.. so my experience is ghost.. ghost images.. on large commercial server setups, can stream restore to multiple computers at once.. even doing it computer by computer the image is simple as network boot to restore. But ghost went the way of Symantec.. sigh!! And was destroyed.
    A product like clonezilla, Free linux boot cd.
    http://lifehacker.com/5078397/clonezilla-backs-up-and-restores-your-disks
    Can backup a Hard disk in just about any format.. yet to try it on a Mac to a TC.. but I will. Boot from CD.. instead of your lost Lion partition which no longer exists (because the hard drive had to be replaced) and the DVD they no longer give you, and restore the entire hard disk in a couple of hours .. to the exact image at the point you made the clone.. in any format, with any partitions.
    My bet is that it will kill TM .. but you could be right.
    It is just the prospect of all those permission changes, photos and mail libraries etc that worry me.

  • I would like to add my Deskjet F4480 printer to my home wireless network. How can this done?

    I have a Linksys wireless router that is the hub of my home wireless network.  I have been successful in adding a HP OfficeJet 6500 All-in-one Printer an old HP DeskJet 890C that I purchased in 1997 with a computer running Windows 95.  The HP 890C has been my tireless workhorse throughout my two kids K-12 school as well as printing reams of paper during my MBA...and guess what: it still works.  However, my daughter has just returned home from college and she has a HP DeskJet F4480 printer/scanner that she would like to add it to the home network.  I have been researching the problem, but haven't been successful in finding out if this printer is compatible to add to a wireless network.  Or simply, will a 802.11g Wireless USB 2.0 Adapter suffice?  I am also adding a new Windows 7 laptop in the network, that will need to print to this F4480.  I patiently await the forum's response.

    My mistake, it seems that price was a deciding factor when I purchased the F4480 in lieu of a more expensive wireless ready printer-scanner.  I will eventually come-up with a solution as I did with the 890C where I have a wireless print server connected directly to the printer serial connection.  It seems that backward compatible is still evident, but I am having some problems coming up with the long-lasting HP49 and HP23 tri-color ink packs. 
    Here is the rub; I don't replace technology because it is out-dated. I upgrade and or repair everything myself. I found warranties not worth the paper their written on and in most cases, the technical support was lacking.  My Win95 desktop went thru several major components until I found that it was becoming harder to find software to run with it.  I finally replaced it in 2007.  Now it seems that there has been a paradigm shift toward utilities that are very hungry for memory, and even if I didn't want to, I am forced to come over to the dark side with a device that has a minimum of 8GB of RAM. 

  • Hi, I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand new a while ago i was trying to connect to my home wireless network it said that your airport is not configured then I restarted the system but it didn't restart it shows the "

    Hi,
    I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand-new (the 4th time to use the device) a while ago i was trying to connect to my home wireless network it said that the connection is timed out so i clicked the airport sign on the top it said that your airport is not configured then I restarted the system but it didn't restarted it showed the grey screen with the apple logo and the spinning wheel for more than 10min so I tried the force shutdown by pressing the power button till it switched off I waited for 5min then pressed the power button to start or boot the system and again the grey screen with the apple logo and the spinning wheel, I waited for more than 20min nothing changed, any solution please?
    Your help is really appreciated"

    Thanks a lot i followed the instructions for safe mode (i found out that i was pressing the C button after restarting) i did whats written there but the repair couldn't be performed so in addition i needed to re-formate the HD so i erased the volume and then repaired the disk--> quite disk utilities --> start the installation from the installation DVD.
    Thanks really appreciating your help

  • Apple devices will no longer recognize home wireless network

    After returning from a week's vacation, I am having difficulty getting my Apple devices (iPads, iPhones, MacBook Pros, etc.) to connect to our home wireless network. I have tried resetting the router and modem numerous times, restarting the devices, resetting the IP address on the MacBook Pro to no avail. At time I do show a connection to the network, however, I cannot access internet, email, etc. This problem also seems to be affecting ALL of our Apple devices, including the ones we left at home. The PC laptop connects just fine, so it does not seem to be a router issue.  Any thoughts?

    Have you called the ISP's tech support line and asked for help?

  • Strange - Home wireless network ok, no access Public networks

    Ok, I'm not getting this, and I've been around computers for some time.
    Got my B570 'round September last year. Worked great on home wireless network ( Brighthouse networks in Florida, with Ubee Wireless modem running Lightning or 40mb.)
    Had to move to new place offering a house offering of wifi, had a bear getting that up, but finally did.
    Here's the q, and I've seen this on an HP laptop running Vista, but that one died and I got this one.
    Go to Starbucks, Panera's, Dennys or just about any other public place, and I can see the routers and even connect, but can't get anywhere on the internet. I get either a limited or no internet, or identifying, but that's it. I know that their router is working because i can make the wifi connection on my phone and browse no problem, and I see other patrons with different computers logged in at the same time.
    McDonalds, I can get in, and soon as the network connection comes up, browser will pop up and allow me to accept McD's access rights page and I can connect. I know that Denny's has one too, but it doesnt pop up, and ( I know that this will sometimes happen too ) if I try to connect to a website, sometimes the local accept page will pop up, but usually not for me.
    I have Google Chrome as my primary web browser, but even if I try to bring up via IE, no go.
    I can connect to the internet via my droid phone usb wired or just wireless, but don't like that to be a regular solution.
    I've already tried to update the wireless driver ( Broadcomm ), but computer tells me that i'm up to date. Enabled then re enabled. Flush DNS didn't help either, ipconfig / release and renew didn't do it either. Using Comodo Internet Security, and turned it off, even exited out of program and that didn't help either.
    Today was an interesting day. went to Denny's thinking I'd get some work done, and couldn't get logged in. Went to Fedex Store to get some printing done, and logged in right away. Came home and can log into the communities public ( fee based ) network and can log right in. Looked in my bag and found a usb wifi dongle I had used for the HP when the wifi on it died out, but didn't try that yet. I'd rather not, I'd rather find out why the wifi on this laptop seems to be finiky with who's networks I'm using.
    Any ideas would be appreciated.
    Ron V.
    Lenovo B570 - 4 G Ram, 500 G H/D
    Windows 7 Home Premium 64b

    hi Ronjie,
    The issue you're facing is a very strange issue. From what i gather ist begging to choose the network it wants to work with. I may need more time to look inot his to see if it is a harware issue. But i would like to try something though. You may want to uncheck the IPV6 in ur Wireless network properties. 
    To do that you will have to go to your "Network sharing centre" > Click on "Change adapter settings"  on the left hand panel > Highlight "Wireless network Connection" > Right Click "Wireless network Connection" and select on "Properties". Be sure to uncheck the "Internet protocol version 6 (TCP/IPV6)". Then click on and try to reconnect.
    Let me know how it goes..
    Regards

  • Setting up HP Officejet 6500A; not sure how to connect to web w/ home wireless network

    I have a small home wireless network.  I set the printer up today but it says that I must connect to the internet (fax part is working).  The only desktop I have, I keep off most the time and just use my laptop (which is for work so I can't set the printer up to this).
    Is there a way to connect the printer directly to my router?  They are only a few feet from one another; however, I have no clue how to do it and the instructions manual didn't tell me much.  Do I need a phone line?  What would I use to connect the two?
    This question was solved.
    View Solution.

    Use an Ethernet cable, available in any tech store, online or even Target will have them.
    Plug it into the back of the printer and router.  You should be able to add the printer to your laptop.  Let me know what operating system you have and I can help.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

Maybe you are looking for

  • IPod shuffle 2nd Gen not appearing in Windows Vista

    Dear All: I have a 2nd Gen shuffle that will not show up in iTunes or Windows on a Vista Home Basic machine. Vista finds an unrecognized USB device and cannot find a driver. The orange light on the shuffle blinks, and the Vista device manager keeps d

  • LOST recovery disk

    i lost my cd's now am havin problem with my sound system I opt to format my pc but I can't afford a win7 as am a student don't wanna use cracked and now I have no recovery cds pls can I possibly download this or any other means? Am in africa and can'

  • MDM Adapter query

    Hi Experts, My scenario is MDM to JMS(MQ). MDM side sends file in a MDM adapter, now the problem lies in the part that PI has to send files based upon timestamp order and syndicate them to Mainframe. Now, for File Adapter there are options in which w

  • Need to find Video Effect Button cuz its not in Inspector

    In my iMovie 11 i have audio effect instead of video effects in the inspector. i don't know how to change it/ or find video effects button. Help? thanks

  • Can you export to a Bluetooth device?

    I wonder if it possible to export pictures to a mobile phone via bluetooth.