Advice on buying AV amp and wiring for Audig

Hi:
I just got a Dell 8400 (P4- 3Ghz) with MS Media Center 2005. It has a Dell Audigy 2 card. I have an entertainment center with a 42" Monitor and a 6 yr old Pioneer AV/Dolby amp that is toast. The speaker system is a Bose Acoustimass 7 for both front and rear which is built into the room. I also have a Sony SA WM20 50 watt SubWolfer.
I want to replace the AV Amp and dri've the whole HEC from my PC using MS Media Center 2005 and it's remote. Any suggestions on what my options would be will be appreciated. I also need to know which type of wiring digital or analog would be best.
Thanks

I was referring to DVD audio. I ended up using analog outputs to my Denon as it was the only way I could adjust treble, bass, presence, Dolby enchancements etc. .
The PC screen appearance on my 42" ED plasma is not good . I am able to use the plasma as a PC monitor for setting changes (I am very familiar with the settings screen and can move around it easily even though plasma image is not clear) but plasma is useless for general surfing as images are not sharp. I have a Radeon 9800 Pro card (dual monitor setup). I'm told the Radeon is a high end product but using the plasma as a PC monitor leaves much to be desired. Not the sharp images you see in Mark Harmon's office on tv show NIS. Also, have codec problems with card when watching DIVX movies. Have to change card settings to make plasma primary and computer LCD monitor secondary. (ATI Radeon recommends configuring LCD as primary, plasma as secondary). Don't know what kind of luck you'll have with your Mitsubishi.
I use Gyration wireless keyboard/mouse for plasma (in addition to wired keyboard/mouse with computer in equipment closet). It works great but then again I don't use plasma as PC monitor due to lack of clear image. PC is thirty feet away from viewing seating, behind one wall.
Why conduit's I would try generic S cable as a test to see if your going to be able to use Mitsubishi. If it works out, you may want to upgrade to a video quality S cable with integral shielding. I use a 30' VGA cable (RGB video) for MCE2004 programs. I seem to recall that 30' was as far as you wanted to go with video cabling? Hope this hel
ps.

Similar Messages

HT201272 I'm trying to buy some gold and money for one of the race games but they said contact i tune

Imtrying to buy some gold and money for one of the race games but they said I should contact I tune

Welcome to the Apple Community.
Did you follow the instructions in the message and contact Apple, which you can do through iTunes Store Support. If Apple have asked you to contact them, then the issue can only be resolved by them.

The best way to connect wireless and wired for a WRT160N.

It took me about 4 hours to find out how to connect wireless and wired to a network using model WRT160N. Here is what I have done. First install the CD when it says there is not connection connect your PC, Modem and router Andy any wireless are wired products, after that do what the linksys advisor tells your which is default. When it gives you the security key write it down because you will need it for your wireless and wired Products. Under security mode type your SDD name and where key 1 is type your security password with was given to you. Remember all you wireless products have to have the same SDD Like Linsys and all your wired products have to have a different name like Linsys2 but your Key 1 numbers has to stay the same. That is all you have to do. Remember that wireless and wired has to be in sequence. That should do it.

Hi David Hamilton1;
I guess that all depends on how critical your data is in relation to how much time you want to spend doing the erasure. Those higher level erasure options can take a significant amount of time to complete. Personally I don't have anything on my Mac that I think is worth more time then a simple erasure even if that does leave it some what recoverable. To me it seems some people are going overboard on this issue.
Allan

Buying in Kg and issue for production in Litres

Hi All,
One of my client is having a requirement where they buy raw material in KG and issue for production in Litres. Based on density of the material when issues in litres the same should be converted into Kilograms automatically and deduct it from Instock.
How can we map this scenario?
thanks
SV Reddy

HI SV,
Even though you have closed this thread, let me offer some of my experiances in the Base Oil industries.
They had the same requirements as you except that when they received Base Oil from their supplier, its in Litres and when they issue to Production (as a component) its in KG for the the "Filler" to use a scale to measure how much he is putting into the tank. Another diff is that each "Batch" of Base Oil has its own charrecteristics and the density and viscosity is never exactly the same.
We solved this with
- keeping the Inventory Unit of measure as LTs, what they use in when Purchasing ps: the finished product is always in Litres. ie: Kgs in -> Lts out.
- Each bathc of the item recieved has a factor based on a chart and formulars that gives the "Unit Ratio" for the KG : LT
- So when they buy in LT, in the Purchase Order, its straight forward. BUT, when they issue to production, the Production order calculates the Weight of what is required and prints it on the Production order Sheet. This way the production guy does not have to go through the calculations manually all the time. The Production Order takes the Litre Base Qty and checks against the selected "Batch"'s "Unit Ratio" and does the calculation and stores it on that items line in the Prod Ord.
This has been working for them and we have modified it to suite other items that have other Production Charrecteristics Requirements.
A bit complex but im sure the concept applies to alot of Liquid Manufacturing Industires.
Regards.
P.S: this was all achieved with and an Add-On Development
Edited by: Noor MC Jooma on Jun 8, 2009 5:25 PM

I have Garage Band for my Macbook Pro. It runs on OS 10.5.8. Can I buy JamPack loops and sounds for it? Thanks.

Can I purchase JamPack loops and sounds for MacBook Pro, running on OS 10.5.8? I already have Garage Band app.

First you would need to meet these requirements:
To install Mavericks, you need one of these Macs:
iMac (Mid-2007 or later)
MacBook (13-inch Aluminum, Late 2008), (13-inch, Early 2009 or later)
MacBook Pro (13-inch, Mid-2009 or later),
MacBook Pro (15-inch or 17-inch, Mid/Late 2007 or later)
MacBook Air (Late 2008 or later)
Mac mini (Early 2009 or later)
Mac Pro (Early 2008 or later)
Xserve (Early 2009)
Your Mac also needs:
OS X Mountain Lion, Lion, or Snow Leopard v10.6.8 already installed
2 GB or more of memory
8 GB or more of available space
Genius bar could help you over the counter
Genius reservation http://www.apple.com/retail/geniusbar/
http://store.apple.com/us/product/MC573Z/A/mac-os-x-106-snow-leopard

Advice before buying Macbook Pro and Final Cut Studio

Hey there
I'm looking for advice before I buy my first Mac.
Currently editing SD video using Windows PC, Quad core, and Sony Vegas Movie Studio.
Now I want to edit HD (from Canon5Dii) and plan a move to Macbook Pro & FCStudio.
What hardware configurations of MBP (with FCS) have folk out there got, and how well do they run?
Eg. Do I need the 8GB memory?
Any peripherals I MUST have
Thanks in advance
Aye
Message was edited by: sam4rufus

Any peripherals I MUST have
Fast, external hard drives for media storage. Don't use the internal system drive for this. Don't even consider using USB drives at all.
All MBPs limit you to FireWire 800 drives, which are OK for lower bandwidth video like HDV and AVCHD.
Although the 17" model also has an ExpressCard slot that can be used with an eSATA adapter to connect much faster drives that provide throughput that FireWire cannot achieve.

Need help with buying graphics card and ram for MSI 865PE NEO 2-V

Hi,
I want to buy 1GB of ram for motherboard MSI 865PE NEO 2-V I need help with finding correct parts.
I also want to buy 512Mb or 1GB graphics card.
as i said before i need help with finding correct ones so they match motherboard, I would appreciate if any one would post link to cheap and fitting parts.
I found graphics card allready, i just need to know if it will fit.
the card is
NVIDIA GeForce 7600 GS (512 MB) AGP Graphics Card
Thanks for help.

here you can see test reports for your mobo:
http://www.msi.com/product/mb/865PE-Neo2-V.html#?div=TestReport

Do You Know If My Psu Is Correct Amp And Volt For Run My Fx5900?

HI help me !!, i bought my MSI geforce FX 5900 i want know if my PSU is correct for run best with my card
5,5V -- 12 V
3,3V -- 20A
12V -- 15A
thanks

i thought your 12v rail must be 18A[20A] or over. And you are
using AMD 64 which needs much power as like 5900 soo try to buy a PSU with 32A on the 12V rail [Good CPU-GPU needs Good PSU]
Buy a good brand PSU 450w or more power models .{32A-12v} [thermaltake,antec,enermax,Elan vital (asus,acer)]

Buy iPhone 4s and unlock for int'l travel?

Hi all,
I'm active duty military and will be deploying in January. Currently I have the iPhone 4... and CDMA isn't an option where I am going. Yes, I know I'll have to pay full price. I'd like to stay in touch with my wife (via e-mail... voice is too expensive!) so i thought about purchasing an iPhone 4s.
What I'm wondering is will Verizon unlock the 4s for me so I can purchase a local sim card where I'm going? Keep in mine I'd be buying at full price (not upgrade eligible) and on military orders. Data that way is cheaper than Verizon's 250 MB allotment.
I remember the good ole days when I could turn on the unlimited e-mail/data blackberry package when I went abroad... my wife and I were able to stay in touch so easily!!!

silver6055 wrote:
kaebfly wrote:
That question could probably be answered tomorrow by calling Verizon and asking. If not tomorrow then I'm sure the answer can be had for sure on the 14th.
Well, I'm sure AN answer can be had, the question is whether it will be correct! I don't know if you have ever tried getting a phone unlocked within the first week or so of its release. Generally the reps haven't been told the procedure for that phone,and haven't got the codes and really cannot help. For whatever reason, some of them will give an answer anyway, I have heard "The phone cannot be unlocked", "We don't do that anymore", "It can only be unlocked when you are abroad", "It doesn't need to be unlocked", "Use the last four digits of the phone number" (Yes, I've had a lot of phones unlocked over the last few years!). Now I don't really mean to knock them, once they have been trained on the phone, the Global Services people are usually very helpful
So, it may take several weeks to get the correct answer.
With this being a user forum with only occasional responses from VZW reps (that usually give general answers that often don't apply to the iPhone...such as "remove the battery and then replace it to do a hard reset) you are less likely to get an official and unequivocally "correct" answer on here either. Add on the fact that this is a new global iPhone that no user on here has experience with and you can pretty much expect guesses and theories more than fact. Yes, people can tell you how it works on other global devices, but no one can tell you how it will work on this 4s when no one has actually had their hands on it and had the experience of trying to get it unlocked. THAT is why I said calling VZ would be the best option for getting an answer. Or...you can wait it out on here and wade through the theories...but that could still take several weeks.

Why I have to buy Lion Server and Lion for $83.98???

I want to upgrade my MAC OS X Server 10.6.8 to Lion Server......
But the App store insists I buy Lion as well... AND it has tried to charge me $83.98 for it.... (The Australian dollar is closely on parity with US dollar)..
So.. I already downloaded Lion.... and installed on my imac.... now I want to upgrade my server.. why do I have to buy lion again??? And why so expensive compared to the rest of the world??
Gaz

For those that don't see the prompt to buy Lion + Lion Server again, there's no need to respond because you aren't having this issue and any obvious input, is just that.. obvious.
For those with this issue, Apple Care won't be able help you because it's a download issue and not an install issue and they suggested to contact the Mac App Store (iTunes Store) support for assistance. Sadly it's e-mail only and probably will take some time. You could try a clean install of SLS to upgrade to LS, but that still might not work. Other than attempting the pain of wasting a day to do a fresh install before the upgrade, I've tried logging out and back in with the Mac Store, created a second admin account and used the same AppleID and both still prompted me to Buy Lion+Lion server again.
For those that haven't clicked on the buy, I still hit an issue that preventing me from downloading the Lion Server after the 4GB Lion image downloaded. You will probably have to request the refund if you attempted this, but guessing you still won't be able to install. Also if you try to upgrade from SLS to just Lion, you will be prompted to buy Lion Server as well. So in the end, it's up to the Mac App Store e-mail to resolve this or perhaps I can attempt to do the clean install.

Advice needed - optical bay caddy and HDD for T530

Since I rarely use my optical drive and frequently back up files to an external hard drive, I'd like to put a HDD in the optical bay and just swap it out for the DVD player whenever that is needed.
My T530 (i5-3210M Win7HP) has a 256GB Crucial mSSD for the boot drive and programs; the original 500GB/7200 rpm in the drive bay has data files, Outlook and Quicken files, music, photos and documents.
For the optical bay HDD 500 GB would be plenty, but the 750 GB is only about $10 more, so why not? (I'd probably put the 750 in the drive bay and make it the data drive, with the 500 in the optical bay for a back up drive... and this is about convenience more than need.)
Best I can tell the optical drive supports SATA 6GB/sec but most of the 2.5" 750GBx7200 rpm drives are SATA 3GB/sec. (On the other hand, the Hitachi MK5061GSY 500GBx7200 that came in my T530 appears to be 'only' SATA II, and most forum posters suggest there's not a noticable difference.)
Of the 750 GB drives it seems the Seagate Momentus ($82) and Western Digital Scorpio Black ($78) would be the top two choices. I think they're both 9.5mm and would fit. Some reviews indicate the Western Digital is quieter.
The caddy is more problematic, as there are so many choices, and many appear to be poorly-fitting Chinese knockoffs. I'm not inclined to pay $70 for the Lenovo, when the others are in the $10-15 range, but I do want one that fits well and works well and lasts. (And is at least SATA 3GB/sec.) I can't tell much from the prices or pictures, and there's contradicting information in the 'product reviews.'
So I need a 12.7mm optical bay (Ultrabay) caddy for a 9.5mm HDD that fits well without gaps, matches the T530 case, and supports at least SATA 3GB/sec.
Will I need the rubber 'bumpers' or is that just for SSD drives? If I need them, do they come with the caddy or drive? If not, what do I get and where?
Does either the Seagate or Western Digital offer an advantage in function or reliability?
Please correct anything that I've mistated or misunderstood. Thank you for your advice and recommendations.
Solved!
Go to Solution.

How the four screws work.
HD's and SSD's usually have four threaded holes on the bottom and also two threaded holes on each long side. The video you may have seen with the screws going through holes in the bottom of the caddy into the threaded bottom holes of the HD is a video of the $45 Newmodus caddy. That's how they affix the drive to the caddy.
The Chinese caddy I linked uses the screws in a different way, and it is actually pictured in the top right illustration on the caddy.
While the drive is out of the caddy, you just thread the screws (through nothing) into the side holes on the drives. So, the drive now has two little protruding screw heads on each side. The only purpose is to create those four slight protrusions - two on each side.
Then you insert the drive into the caddy by sliding from one end. The thing on the bottom of the caddy picture is like a little door that folds up and down. You lift up the door and slide the drive into the other end. The protruding screw heads slide under little rail protuberances that are molded inside the sides of the caddy. When you have slid the drive all the way forward into the electrical connectors, you then snap down the door behind it. The door prevents the drive from moving forward or back. The screw heads wedged under the rails prevent the drive from moving up or down. You can do the entire operation in 5 seconds.
Ny-compu-tek seems to have the same caddy listed under various titles and prices, including one that specifically says T530. I think that's just a marketing gimmick, as the T530 takes the same caddy as the T520. Anyway the one I linked is the least expensive from that source and fits perfectly.
It was also shipped out in one day with a tracking number.

Best Practice for Buy in Set and Dismantle for Sales

Hi All SAP Masters,
We have a scenario that when purchasing an item as "set", in this set, it has a few components inside this set (something like a material BOM). Example, a machine which comes with several parts. However, when the user received this set from the supplier, the user would further dismantle certain part(s) from the set/"machine" and sell it separately to the customer as a component/"single item".
What is the best practice in the SAP process to be adopted?
Please help. Thank you.
Warmest Regards,
Edwin

If your client have PP module , then follow this steps
Consider A is the purchased material and going to dismantle the A into B, and C
1) create a BOM for B material
and assign the header material A as consumption material with + ve qty
and C component as byproduct and maintain - ve qty in BOM
2) maintain backflush indicator for A & C in material master MRP2 view
3) create routing for B and maintain auto GR for final operation
4) create a production order for B
5) confirm the order in Co11n, A will be consumed in 261 movement, C will be receipt with 531 movement
B will receipt in 101 movement .
once the stock is posted into unrestricted you can sale B & C

Can I buy an item and pay for it later?

I am planning to buy a gift card later in the week and I have no credit card or money in my account. Could I still buy the item now and the difference be subtracted when I redeem the gift card later?

Sorted it!

Constant disconnect for wireless and wired for the past two weeks...

And it's becoming worse and worse. I don't understand and Verizon has escalated my problem - BUT NO ONE HAS CALLED ME BACK. It's been over two weeks. I've restarted, reset, rebooted, screen shared with tech support. They even sent me a new modem. Both modems behave the same way. I know it's an outside line issue. It has to be. This started after a bad storm. They won't listen though. Tonight - I ordered Comcast Internet. They are coming to install on Thursday. If Verizon can't fix by then they are done in my book!

Be prepared to be moving on to comcast then, I've had the same issue for 3 months now, 3 techs, 20+ hours of phone calls, multiple no call backs and been hung up on a few times, even here my topic gets locked and no help is provided Verizon doesn't seem to be willing to fix actualy problems with their service so by all means switch to a company who will

How come My iTunes (10.5.3.3) says I don't have enough store credit to buy an app and asks for billing info when I have more than enough money to buy the app? (app is $6.99, I have $7.11)

How can I solve this and pay with my remaining store credit?

App purchases will require you to pay applicable sales tax.

Advice on buying AV amp and wiring for Audig

Similar Messages

Maybe you are looking for