Advised to get an "extender" to be able to stream netflix, etc. through new digital tv. Apple store told me to buy Airport Express and set up WDS. Upon reading about WDS it stated cannot set up WDS with Airport Express 802.11n,

I was advised I needed an "extender" to stream Netflix, etc. through my newly purchased digital TV. Apple store advised me to buy Airport Express and choose WDS setting. When reading instructions on how to set up WDS it states cannot set up WDS with an 802.11n airport express, which is what they told me to purchase. How do I set up this Airport Express to extend my internet signal from my modem & airport to be able to stream internet capability to my TV?

Similar Messages

Speed issue with WDS, Airport Extreme, and Airport Express 802.11n

I have a Airport network set up using WDS and two airport base stations: an Airport Extreme 802.11n, and an Airport Express 802.11n. The Extreme is configured to be WDS main and is connected to my cable modem and other computers, while the express is WDS relay and acts as a switch.
I don't actually have any wireless clients connecting to the express. I'm using it to connect a mac with no airport card to the network by plugging it into the ethernet port on the express. For the most part, it works, and the mac gets a network address and can access the network. However, the connection speed from the Express to the Extreme seems slower than it should be.
Since both are 802.11n, and the Mac is plugged into the Express's 10/100 ethernet port, I figure the theoretical top speed that the Mac should be able to communicate with another device plugged into the Extreme is at around the same speeds as 100 mbps ethernet, since the 100 mbps ethernet connection should be the bottleneck in this case. In reality, the speeds are much slower: when I transfer files between a machine connected to the extreme (via ethernet) and my mac, the speed tops out at about 2 megabytes a second, if that.
I looked in the Airport Extreme's logs, and it indicates that the Express is only connected at 54 mbps, as though it were a 802.11g Express. I have no idea why this is! Also, the only wireless communication is between the Extreme and the Express, so one wireless device acting as a relay for another (and thus cutting the throughput in half) shouldn't be an issue.
Does anyone know why the speeds are so slow, and if there's anything I can do to improve them?

Hello Brian Kendall. Welcome to the Apple Discussions!
I looked in the Airport Extreme's logs, and it indicates that the Express is only connected at 54 mbps, as though it were a 802.11g Express. I have no idea why this is!
That is because you established a WDS which only runs in 802.11g. Since you have two 802.11n base station, you would want to take advantage of the "Extend a network" feature available with these base stations.
Here's a typical setup:
o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
(ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

Airport Extreme 802.11n should I WDS or Extend to Bridge ethernet?

If I buy two Apple Airport Extreme Base Stations (dual-band 802.11n) can I set-up WDS without dropping speeds to G? I've read that if I have any 802.11b/g clients that the entire WDS clocks down to 802.11g. I'm wondering if that is true with the new simultaneous dual band models? Can't I WDS the 802.11n bands and offer 802.11g simultaneously to clients on the other band without bringing the WDS down? Do I want to?
I would just "extend" but I don't want to have the wireless clients have to go through two "hops" to get out to the internet. As I understand it... all of my wireless clients would go through the relay, then to the main, then out the Internet instead of just connecting straight to the Main. My range doesn't need to be extended as far as coverage goes... one base station would cover my entire house. I'm basically just looking at the other AEBSn to act as a wireless to ethernet bridge to a part of my house where I several ethernet enabled devices out of hardwire range. Do I need the AEBSn or maybe just the new 802.11n AE?

Welcome to the discussions!
+I'm basically just looking at the other AEBSn to act as a wireless to ethernet bridge to a part of my house where I several ethernet enabled devices out of hardwire range. Do I need the AEBSn or maybe just the new 802.11n AE?+
The simplest, which may also be the best way to do this is use an AEBS as your "main" router and configure an AirPort Express 802.11n to "join" the wireless network and enable the ethernet port. Then connect a simple 5 port switch to the port on the AirPort Express for your ethernet devices.
Oddly, if you configure a second "remote" AEBS to "join", the ethernet ports +are not+ enabled on the AEBS. The ethernet ports are enabled, if you configure it to "extend a wireless network".

Speed issue with TC and Airport Express 802.11n in WDS mode...

Here is my problem.
I replaced my older base station / Express duo with
a new Time Capsule (1TB) and a new Airport Express (802.11n).
I set up the network with the TC as base station running a WDS network (WDS main) and the Express is the WDS remote.
When I check the wireless clients from the TC, I find my iMac running at 130Mbits and the Extreme at 54Mbits.
No other wireless clients are connected to the network (I kept my slower network as a parallel one for my "older" Macs).
The only other connected device is my Dish network DVR that is connected via an Ethernet cable directly to the Express.
So my question is why does the Express not communicate at >54 speed rate with the TC?
And, why does my iMac connect with 130 and not with 300Mbits?
Any thoughts?

Instead of using WDS, you should take advantage of the "Allow this network to be extended" option that is available for the 802.11n AirPorts including the TC. WDS only operates in the 802.11g radio mode.
Here's the basic setup:
o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
(ref: Page 46 of "Designing AirPort Networks Using AirPort Utility).

I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

Let me see if I can help you with the basic WDS configuration steps:
Note: To help facilitate the setup, temporarily connect the AXn directly to the AEBS LAN port using an Ethernet cable. Once the setup is complete, you can move the AXn to the desired location. For all configuration steps you will be using the AirPort Utility. Before starting, be sure to jot down the AppleIDs for both base stations.
802.11g AirPort Extreme Base Station (AEBS) Configuration
AirPort Utility > Select the AEBS > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network
Manual Setup > WDS tab
WDS Mode: WDS main
Allow wireless clients (checked)
WDS Remotes: <enter the AppleID for the AXn here>
Click on Update and allow the base station to restart.
802.11n AirPort Express Base Station (AXn) Configuration
AirPort Utility > Select the AXn > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network (Note: You may have to hold down the Option (Mac) or Control (PC) key to see this option in the list.)
Manual Setup > WDS tab
WDS Mode: WDS remote
Allow wireless clients (checked)
WDS Main: <enter the AppleID for the AEBS here>
Click on Update and allow the base station to restart.

Extending range of Linksys WRT310N router with Airport Express 802.11n

I am trying to extend the range of an existing wireless network set up with a WRT310N router with an Airport Express 802.11n - I've tried choosing both "Participate in a WDS network" and "Extend a wireless network" and both have run into problems.
Any advice would be greatly appreciated!
Thanks, Amy

amysinsh, Welcome to the discussion area!
Sorry but this is not possible.
It would be possible if the wireless network was created by another AirPort Express (AX), anAirPort Extreme base station (AEBS), or a Time Capsule.

Setting up Time Capsule with existing AirPort Extreme 802.11n and AirPort Express.

I already have and am using an AirPort Extreme 802.11n with an AirPort Express. I want to set up a Time Capsule 802.11n. Which is the best way to configure this?

... Which is the best way to configure this?
The answer depends on what you need the TC to accomplish. If all you need it to do is perform Time Machine backups, simply have it join your existing network in client mode. It would be if it were to connect to your existing router (presumably your Extreme), not through an "extended" wireless network (presumably your Express).
If you need the TC to "extend" your network so as to serve additional wireless clients, you can do that also. Configure it to "extend" the network created by your Extreme.
As you can see it's quite versatile.

HT204053 I did not know my kids had set up an Itunes account for me with one user name and password. then i got an i phone and set it up with a different email address and new password. how can i get my accounts to merge so i can have all of my music on

I did not know my kids had set up an Itunes account for me with one user name and password. then i got an i phone and set it up with a different email address and new password. how can i get my accounts to merge so i can have all of my music on my iphone

Quote: "You cannot merge two or more Apple IDs into a single one. You can, however, use one Apple ID for iCloud services and another Apple ID for store purchases (including iTunes in the Cloud and iTunes Match). See “Using one Apple ID for iCloud and a different Apple ID for Store Purchases” above for details." See also Apple ID & iCloud FAQ: http://support.apple.com/kb/HT4895?viewlocale=en_US&locale=en_US
You can set up your iCloud account on your iOS device under: "Settings > iCloud" and a other account for store purchases under "Settings > iTunes & App Stores". Unfortunately merging accounts is not possible but you could transfer all of your music manually via iTunes from your Mac or PC.

We just got 2 iPad air today and Set up both with the same Apple ID, now I'm getting messages and FaceTime for my 13 yr old daughter. Do I have to create a different Apple ID for her?

We just got 2 iPad air today and Set up both with the same Apple ID, now I'm getting FaceTime and messages for my 12 yr. old. Do I have to set up a separate Apple ID for her to avoid this?

It's a trust issue. You can set them up so you don't receive each other's messages as long as you each have your own email address.
The trust issue is the fact that either of you can change the separation at any time via Settings by checking the appropriate (inappropriate?) email address.
To be absolutely sure you can never receive each other's messages will require two Apple IDs.

I have a problem with IDVD when I have completed a movie and set it up with menus etc I cannot operate the burn button so I cannot make a DVD.

I have a problem with IDVD when I have completed a movie and set it up with menus etc I cannot operate the burn button so I cannot make a DVD.

Hi
Can You
Go up to File Menu in iDVD - and here down to
Save as a DiskImage
If this works - You can burn Your DVD in another way via Disk Util tool
Yours Bengt W

HT4527 Hi My old computer broke down. I could not transfer anything across to my new PC. Unfortunately I forgot my old i-Tunes account and set up a new one with the new PC. However, I cannot now synch my music on my i-pod to my new PC - how can I do t

Hi My old computer broke down. I could not transfer anything across to my new PC. Unfortunately I forgot my old i-Tunes account and set up a new one with the new PC. However, I cannot now synch my music on my i-pod to my new PC - how can I do this?
I'm a bit of a technophobe so any help gratefully received thanks

It has always been very basic to always maintain a backup copy of your computer. Use this to put eveything back.

WDS networking issue - Airport Extreme (802.11n) and remote Airport Express

*Background Info:*
Airport Extreme 802.11n (Fast Ethernet)
Version: 7.2.1
Wireless Mode: Participate in a WDS network (set as main)
Network Name: @Home
Wireless Security: WPA/WPA2 Personal
Channel: 1
Airport Express
Version: 6.3
Wireless Mode: Participate in a WDS network (set as remote)
Network Name: @Home
Wireless Security: WPA/WPA2 Personal
Channel: 1
Radio Mode: 802.11b/g compatible
Connect Using: AirPort (WDS)
Connection Sharing: Off (Bridge Mode)
Issue
Please help as I'm having issues with my WDS network. I've setup using both the wizard and manual and also hard reset on both units to setup again but cannot get them both to communicate to one another. Both units are showing green LED under their configuration. For my last attempt, I've tried adding the Airport ID (MAC) of the Airport Express to the Access Control and also DHCP Reservations on the Airport Extreme but still no luck.
The Airport Express (setup as remote) does not even show up in the Airport Extreme's Summary as Wireless Clients. In the WDS tab, the Airport Extreme is set up as WDS main, Allow wireless clients box checked and WDS Remotes has the Airport Express' AirPort ID in the list. On the Airport Express, WDS is set up as remote, with Allow wireless client box checked and the Airport ID of the Airport Express in the WDS Main.
I can connect clients to both units. Both units are configured using the same Network Name and have the same WPA/WPA2 security key. The Airport Extreme (main) however is connected to my broadband so any devices or clients connected to it are able to get outside. Connected devices or clients are assigned IP address via DHCP with IP 10.0.x.x. If wifi devices or clients connect to the Airport Express (remote) they are assigned a completely different IP addresses 169.254.x.x, they are not able to browse the internet or talk to other clients connected on the 10.0.1.x network. The Internet Connection configuration on the Airport Express (remote) is Connect Using Airport (WDS) and Using DHCP. I've even tried manually and entered the IP address 10.0.1.199 that I had assigned to the Airport Express from the Airport Extreme and Router Address as IP of Airport Extreme (10.0.1.1).
I think I've tried everything but I'm still having this problem. The remote Airport Express is not extending my existing Airport Extreme network. Any ideas???

Christopher,
This may or may not be helpful, or it may be something you've already tried or are aware of so I apologize if that's the case.
I have been researching ways to set up the Dual Band Network supported by the AEBS and came across your post. I've got an AEBS and (2) AirPort Express set-up currently (AEBS is main and the Express are participating in the WDS as remotes) and I'm trying to configure one of the Express to utilize a 802.11b/g compatible network while the AEBS runs a 5Ghz 802.11n Only network.
AAR, since the AirPort Express are 2.4Ghz 802.11b/g ONLY (no support for 802.11n), you have to be sure to set-up your AEBS first and select "802.11n (802.11b/g compatible)" in the Radio Mode drop-down on the AEBS before you attempt to connect an AirPort Express. The AEBS should be set-up as your "WDS main" and the Express should be set-up as a "WDS remote" for the network you established when you set-up the AEBS.
Bottom line here is the Express won't be seen by the AEBS unless the AEBS is 'looking' in the 802.11b/g 2.4Ghz frequency.
Hope this was helpful.

Extending a network with two AEBSn 802.11n base stations

Problem: Laptop on remote Airport Extreme (n) doesn't get internet, but can see entire network.
I have set up 2 new Airport Extreme's (n). One is connected to the cable modem and set to "create wireless network" and "Share a public IP address" . The other is about 80-100 feet away and set to extend the network.
A PowerBook G4 is connected to the remote Airport Extreme and gets an IP address correctly, and can connect to a computer on the primary Airport Extreme. Transfer rates from the remote laptop to a computer on the primary Airport Extreme are strong (15-30 Mbit).
According to the Airport utility, link speed between the two Airport Extreme's fluctuates between 104 and 130 Mbit.
The problem is that the computer connected to the remote Airport Extreme can't get out to the internet. Computers connected to the primary Airport Extreme get a very fast connection to the internet. What am I doing wrong?
Airport Extreme 802.11n Mac OS X (10.4.9) AEBSn

Let's double-check your AEBSn's settings...
AEBSn - Extending a wireless network Setup
- If practical, place the base stations in near
proximity to each other during the setup phase. Once
done, move them to their desired locations.
- Open AirPort Utility and select the base station
that will connect to the Internet.
- Choose Manual Setup from the Base Station menu, or
double-click the base station to open the
configuration in a separate window. Enter the base
station password if necessary.
- Click AirPort in the toolbar, and then click
Wireless.
- Choose “Create a wireless network” from the
Wireless Mode pop-up menu, and then select the “Allow
this network to be extended” checkbox.
- Next, select the base station that will extend this
network, and choose Manual Setup from the Base
Station menu, or double-click the base station to
open its configuration in a separate window. Enter
the base station password if necessary.
- Choose “Extend a wireless network” from the
Wireless Mode pop-up menu, and then choose the
network you want to extend from the Network Name
pop-up menu.
- Enter the base station network and base station
password is necessary.
- Click Update to update the base station with new
network settings.
(ref: Page 45 of "Designing AirPort
Extreme 802.11n Networks.
I followed the exact instructions above with one AEBSn connected to the DSL modem and "creating the wireless network", and a second AEBSn "extending the network". Depending on the location (1st or 3rd floor), my PowerBook G4 connects perfectly to the AEBSn with the stronger signal.

Airport Extreme 802.11n setup done but get disconnected randomly

Dear friends,
I have AirPort Exteme 802.11n WIFI
I did complete set up as per the manual. I set up to use as Extended Network to my existing network.
My PC is window 7 operating system and is updated. I reset my router also.
After connecting to my existing network via LAN and complete setup, network available on my iphone 5
Then I remove LAN cable, it keep ON for 2 or less hours and then gets disconnected and the Amber light on Airport starts blinkin.
I did set up after default setting also.
Please advise.
Regards,
Jayant Joshi

Dear friends,
I have AirPort Exteme 802.11n WIFI
I did complete set up as per the manual. I set up to use as Extended Network to my existing network.
My PC is window 7 operating system and is updated. I reset my router also.
After connecting to my existing network via LAN and complete setup, network available on my iphone 5
Then I remove LAN cable, it keep ON for 2 or less hours and then gets disconnected and the Amber light on Airport starts blinkin.
I did set up after default setting also.
Please advise.
Regards,
Jayant Joshi

Does airport extreme 802.11a/c work with airport express 802.11n

does airport extreme 802.11a/c work with airport express 802.11n

"You can use the AirPort Express to extend the signal provided by the new AirPort, but the Express will not extend "ac" wireless since it does not have that capability. The Express will extend an "n" wireless signal if that helps."
This is what I am trying to understand.
So AXTRM w/ sep SSID for 2.4 (b/g/n) - call it SSID1 - and 5GHz (ac) call it SSID2 - WiFi Explorer confirms AC mode on 5G.
Using an AXPRESS to extend - I have the option of SSID1 b/g/n *and* the 5GHz ac SSID2 in the pulldown (it sees both?) --> if I select SSID1, it also extends this same SSID in 5GHz (both showing b/g/n) >> so I now have 3 signals on SSID1 (XTRM 2.4G, XPRS 2.4G and XPRS 5G) b/g/n and one signal on SSID2 (XTRM 5G AC) ac
If I select the 5Ghz ac SSID2 to extend - it prompts me "do you also want to extend (the 2.4GHz SSID1)?" --> select yes and I now have 2 signals for SSID (XTRM 2.4G & XPRS 2.4G) b/g/n and 2 signals on SSID2 (XTRM 5G 802.11ac & XPRS 5G 802.11 a//n)
Is the 5G SSID2 actually being extended from the Airport Extreme to the Express?
The reason I bring this up is I am having a lot of issues since iOS8 came out (especially on iPhone 6). Everything I am reading is pointing to when people have 2 AP's set to use the same SSID. When you walk to a part of the house where 5G 802.11 ac signal marginalizes, the phone does not immediately hand over to the 5G 802.11 a/n Airport Express.
My thought was separate the SSID's but to me, if the Express can't extend 5Ghz from the Extreme, it's taking a step backwards. I am better off getting a more powerful router like an ASUS and going with one AP, drop the WiFi roaming altogether
Any thoughts?

Advised to get an "extender" to be able to stream netflix, etc. through new digital tv. Apple store told me to buy Airport Express and set up WDS. Upon reading about WDS it stated cannot set up WDS with Airport Express 802.11n,

Similar Messages

Maybe you are looking for