AE not working after upgrading to 802.11b/g/n AEBS

I upgraded to the square 802.11b/g/n AEBS but have lost my AE which I use to play iTunes through my stereo. I just get the blinking yellow on the AE now and there's no longer a pulldown window in the lower right corner of iTunes for me to pick the output (i.e., Living Room.)
I've updated the firmware in both the AEBS and AE. I've run the Airport Utility to make sure I'm getting out to the net via AEBS. But Airport Utility can't find AE.
However, if I reset AE to its factory default, Airport Utility will see AE as having default settings and ask me to Update them. I go through the updating procedure (choosing one time to choose to join the existing AEBS network and at another time, to Create a New Network.)
Both times the Airport Utility eventually will say AE has been successfully updated and go into restart. However, it hangs and after a few minutes says it can't fine ANY of my networks and for me to try again. (And again, and again.) I can get the AEBS back up every time but AE is still lost to me.
Any suggestions as to how to get the older AE to work with the new AEBS?

Hi,
When a wireless network has a mixed environment of 802.11b clients and 802.11g clients, make sure that data rates 1, 2, 5.5, and 11 Mbps are set to required (basic) and that all other data rates are set to enable. The 802.11b adapters do not recognize the 54 Mbps data rate and do not operate if data rates higher than 11Mbps are set to require on the connecting access point.
here is the link which clarifies all your doubts.. and also tabular as well
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap6-radio.html#wp1101903
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

Similar Messages

Iphone 4 Home button not working after upgrade to OS 4.3.5

Iphone 4 Home button not working after upgrade to OS 4.3.5.Please help!!!!!!!!

It seems that settings of mail accounts have something to do with it. I've delete my gmail account and am now using Microsoft Exchange. It seems better, yet not perfect. The issue is definitely due to OS 4.3.1
Apple answer is - no answer. It is a shame that the quality of their products, in terms of design and concept, is not match by a care for customers. It is not normal that I, as a customer, have to spend hours reading Apple Discussions forum to try to understand what the problem is. A little more respect for a customer that spend big $$$ buying their products wouldn't hurt.

File- Export not working after upgrade from 11i to R12

Hi,
File -> Export not working after upgrade from 11i to R12.1.3 in few systems. Can you please let me know what could be the issue.
If export record count more than 200 it is working fine in all the systems and if change the profile option "Export MIME type” value to ‘text/tab-separated-values’ from application/excel also it is wokring.
Thanks and Regards,
Jagadeesha

Enabled the FRD. Below are few last lines. Can you please let me know what i can in this log file contents.
In Argument 1 - Type: String Value: global.frd_debug
Executing GET_ITEM_PROPERTY/FIELD_CHARACTERISTIC Built-in:
In Argument 0 - Type: Integer Value: 196613
In Argument 1 - Type: Number Value: 54
Out Argument 0 - Type: String Value: 12
Executing COPY Built-in:
In Argument 0 - Type: String Value: Entering app_menu.set_prop.
In Argument 1 - Type: String Value: global.frd_debug
Executing FIND_MENU_ITEM Built-in:
In Argument 0 - Type: String Value: FILE.EXPORT
Out Argument 0 - Type: Integer Value: 19
Executing GET_MENU_ITEM_PROPERTY Built-in:
In Argument 0 - Type: Integer Value: 19
In Argument 1 - Type: Number Value: 79
Out Argument 0 - Type: String Value: TRUE
Executing COPY Built-in:
In Argument 0 - Type: String Value: Completed app_menu.set_prop.
In Argument 1 - Type: String Value: global.frd_debug
Executing COPY Built-in:
In Argument 0 - Type: String Value: Completed app_synch.menu_toolbar_sync. Event is WHEN-NEW-ITEM-INSTANCE.
In Argument 1 - Type: String Value: global.frd_debug
Executing NAME_IN Built-in:
In Argument 0 - Type: String Value: GLOBAL.APP_CUSTOM_MODE
Out Argument 0 - Type: String Value: NORMAL
Executing NAME_IN Built-in:
In Argument 0 - Type: String Value: GLOBAL.APP_CUSTOM_MODE
Out Argument 0 - Type: String Value: NORMAL
Executing COPY Built-in:
In Argument 0 - Type: String Value: NULL
In Argument 1 - Type: String Value: GLOBAL.OUT
Executing USER_EXIT Built-in:
In Argument 0 - Type: String Value: FND GETPROFILE NAME="UPK_RECORDING_ENABLED" FIELD="GLOBAL.OUT" N
FNDCPVCM, 11, Built-In, Entry, 316509814, USER_EXIT
FNDCPVCM, 11, Built-In, Exit, 316509814, USER_EXIT
Executing NAME_IN Built-in:
In Argument 0 - Type: String Value: GLOBAL.OUT
Out Argument 0 - Type: String Value: N
Executing NAME_IN Built-in:
In Argument 0 - Type: String Value: system.current_form
Out Argument 0 - Type: String Value: FNDCPVCM
Executing NAME_IN Built-in:
In Argument 0 - Type: String Value: system.current_block
Out Argument 0 - Type: String Value: MASTER
Executing NAME_IN Built-in:
In Argument 0 - Type: String Value: system.current_form
Out Argument 0 - Type: String Value: FNDCPVCM
Executing NAME_IN Built-in:
In Argument 0 - Type: String Value: system.current_block
Out Argument 0 - Type: String Value: MASTER
Executing GET_APPLICATION_PROPERTY Built-in:
In Argument 0 - Type: Number Value: 75
Out Argument 0 - Type: String Value: IHR40P
Executing COPY Built-in:
In Argument 0 - Type: String Value: Completed call_all_libraries. Event is WHEN-NEW-ITEM-INSTANCE.
In Argument 1 - Type: String Value: global.frd_debug
Executing COPY Built-in:
In Argument 0 - Type: String Value: Completed app_standard.event. Event is WHEN-NEW-ITEM-INSTANCE.
In Argument 1 - Type: String Value: global.frd_debug
FNDCPVCM, 10, Prog Unit, Exit, 316509814, /FNDCPVCM-3/P45_30_DEC_201223_28_33
FNDCPVCM, 9, Trigger, Exit, 316509814, WHEN-NEW-ITEM-INSTANCE
FNDCPVCM, 8, Prog Unit, Exit, 316509814, /DMU-4/P8_30_DEC_201223_23_12
# 15 - FNDCPVCM:MASTER.USER_CONCURRENT_QUEUE_NAME.1359399301498413820
WINDOW FNDCPVCM PROGRESS_INDICATOR RESIZE 4198 1500 3
# 16 - FNDCPVCM:MASTER.USER_CONCURRENT_QUEUE_NAME.1359399301512613925
WINDOW FNDCPVCM PROGRESS_INDICATOR RESIZE 4198 1500 3

Ipohone 4 hotspot not working after upgrading to ios7.1 ?

my ipohone 4 hotspot not working after upgrading to ios7.1 but my some friends having iphone 4s its works fine and those having iphone 4 it's not working although we all have same operator and same operating system (i.e ios 7.1).I think this is problem only with iphone 4 users with ios 7.1 , so apple plz fix it in ur next update.

You don't like the answer?
Again it's not a bug, use a supported carrier if you want Personal Hotspot.
Read the list one more time, if carrier is not on the list, IOS7.1 patch the loophole.
Message was edited by: ckuan

Web Service is not working after Upgrade SAP EHP6

Hi ,
Recently we upgraded SAP ECC 6.0 to EHP 6.
We have a custom web service which is consumed in .NET Application to get the Sold To from Sales Order.
the service is working perfectly before upgrade and it is not working after upgrade to EHP6.
When I tested the Service in WS Navigator in SAP, it is working fine.
We raised a message to SAP and SAP analyze the Traces and confirm that the HTTP Request Header coming from .NET application is not having User ID and Password , so it is throwing exception from SAP as unauthorized.
But in service it is configuration as basic authentication and log on using user id and password and .NET application is calling service by passing user ID & Password.
Customer is not happy as it is working before Upgrade and SAP confirmed every thing fine in SAP, but the service is not working.
we did the below steps.
Regenerated the configuration
Re imported the Certificates
Activated the service in SICF.
Please let me know if anybody have same problem or if any steps we are missing.
thanks.
Uma

after changing the .NET Application , Service is working fine.

TS1702 My app store, Apple ID, safari, and most other apps do not work after upgrading to iSO 6, How do i solve this problem?

My app store, Apple ID, safari, and most other apps do not work after upgrading to iSO 6, How do i solve this problem? Can somebody help me please?

The App store is a problem for many and I have not seen a solution.
What is "wrong" with your Apple ID?
Try the following:
- A reset. Nothing is lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup
- Restore to factory settings/new iPod.

IPhone 4's WIFI has been not working after upgraded to 6.1.3(10B329)

     My IPhone 4 was working fine with its WIFI when it is running in default IOS version, I believe it was 5.x.x version, however after I upgraded to 6.1.3(10B329) then WIFI got very aweired issues again and again.starting from then I never get my WIFI working again:
1. Sometimes I can connect to my home's network and keep alive for 1-2 minutes then WIFI will not work on IPone, my home's router is not working either, I need to restart my home's router manually;
2. I can connect to my office's network and keep alive 5-10 minutes then WIFI is not working, however my office router is not affected; however the following days then I can't connect WIFI to office's network any more.
3. I tried to connect to other public area's free network via WIFI, however never joined in.
     I called Apple's service centre couple of times they have no clues, they said they never met this problem before for WIFI not working after upgraded to IOS 6.1.3 and no suggestions from them at all, every time I called them they gave me the same suggestion, such as restore-re-install, check your own router etc, nothing help, however my friend bought a brand new IPhone 4 with default IOS version 6.1.3 which is working perfectly without any issues on its WIFI then I believe this is a completely software issue.
     I know this is a general issue for Apple users and I refuse to upgrade to higher version as I am not sure the higher version can fix this issue however I am pretty sure the newer version of IOS did bring a lot of new bugs, anyone can provide me any suggestions guys ? THANKS A LOTTTTTTTT!!!!!!!!!!!!!!!!
Terrence

I have fixed this issue after upgraded my router's firmware finally, this is a completely compatibility issue between Apple and other third party manufactures, hopefully we can get compabitlity list for each future IOS version ahead of time which can potentially avoid such kind of embarrassing situations moving forward, thanks !

IMessage does not work after upgrade to iOS 8.1.3 to my iPad 4

iMessage does not work after upgrade to iOS 8.1.3 on my iPad 4

I Fixed it by trying to sign in with a different ID and canceling when it asked For a password and then signed in with my ID and it works! No more error message. I got this idea from another discussion. Thank you for replying though.

Bluetooth Driver In Windows 8.1 is Not Working after upgrading please help (pavilion g6 2008Tx)

Bluetooth Driver In Windows 8.1 is Not Working after upgrading please help (pavilion g6 2008Tx)
what cAN i do to make it work?please help

Hi:
If your model uses a Ralink wireless card, see if installing this bluetooth driver works.
http://h20565.www2.hp.com/hpsc/swd/public/detail?swItemId=ob_135494_1

My built in camera is not working after upgrading to a new Skype version

my built in camera is not working after upgrading to a new Skype version

See this thread:
https://discussions.apple.com/thread/5306216?tstart=0
FIX:
1. You need Time Machine
2. Go to folder /Library/CoreMediaIO/Plug-Ins/DAL/
3. Copy AppleCamera.plugin to good place (usb memory stick is the best place).
4. Go to Time machine in date that skype work fine.
5. Change AppleCamera.plugin with file from Time Machine
6. Restart system, Now skype need to work with camera.
If that doesnt pass,
Suggest looking here, much success has been found:
http://community.skype.com/t5/Mac/OS-X-10-8-5-broke-Video-on-MacBook-Air/td-p/18 91729/page/4

ZTE Mf190s Internet USB Modem not working after upgrading to Yosemite.

ZTE Mf190s Internet USB Modem not working after upgrading to Yosemite. any salutation!!

Follow these steps:
go to system preferences.. Open Network..
CONFIGURATION: DEFAULT
TELEPHONE NUMBER : #99*
leave account name and password columns blank
Now go to ADVANCED
IN MODEM MENU
VENDOR : GENERIC
MODEL : GPRS / 3G
Press ok
Then CONNECT.. Enjoy.

Internal speakers not working after upgrading to Maverics

internal speakers not working after upgrading to Maverics

There are many possible causes for this issue. Take each of the following steps that you haven't already tried.
1. Start with the steps recommended in this support article. Don't skip any of the steps. It's the starting point for further efforts to solve the problem.
2. Run Software Update and make sure you have a fully up-to-date installation of OS X.
3. If you've installed an application called "Memory Clean" or any other third-party software that is supposed to "clean" or "purge" memory automatically, remove it according to the developer's instructions and restart. You should do that even if the software is not causing the problem, because it's useless.
4. If you've installed a software equalizer called "Boom" or anything similar, update or delete it and restart.
5. If an AirPlay device is selected for sound output from iTunes (or from other applications via third-party software such as "Airfoil"), deselect it.
6. Launch the application "Audio MIDI Setup" by entering the first few letters of its name in a Spotlight search and selecting it in the results (it should be at the top.) Select the Output tab. If the Mute boxes are checked, uncheck them. Move the Volume sliders all the way to the right.
7. If a red light is coming from the audio-out port, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a mini-stereo jack of the proper size. Inserting any kind of tool in the port may cause damage that won't be covered by your warranty.
If there's no red light, the switch may still be stuck in the headphone position. Try to free it the same way.
8. Disconnect all wired peripherals except keyboard and mouse, if applicable. If more than one display is connected, disconnect all extra ones. Restart and test.
9. If you have a MacBook Air, turn off Bluetooth and restart.
10. Start up in safe mode. Don't log in; just restart as usual when the login screen appears. When you do, make sure the words "Safe Boot" do not appear in the login screen. If they do, the system is still in safe mode and sound won't work.
11. Reset the NVRAM.
12. Reset the SMC.
13. Reinstall OS X after backing up all data.
14. Make a "Genius" appointment at an Apple Store.

Re: NB200-134 - FN key not working after upgrade to Windows 7 Ultimate

My FN keys of NB200-134 is not working after upgrading from Windows 7 starter to Windows 7 ultimate. I tried installing every drivers found on Toshiba website for my lappy but still it does not work.
Help please

Hi asalamk,
The FN keys are controlled by Value Added Package and Flash Cards Support Utility. I think you have forgotten to install these tools
You should check the Toshiba page again and download both tools. Start with installation of Value Added Package then restart your notebook. After this install Flash Cards Support Utility. Once again restart and all FN keys should work properly now.

Personal hotspot not working after upgrading to ios7

Personal hotspot not working after upgrading to ios7

I was having this problem (iphone 5 wouldn't work as hotspot for my PC laptop) and had tried everything suggested on these message boards, so I finally went to the Apple Genius Bar and they fixed it for me. Here's what they did:
1) Turned the Hotspot off on my iphone
2) Went to the Control Panel on my laptop to "Network and Internet" > "Network and Sharing Center" > "Manage Wireless Networks" (on the left navigation panel) and deleted my iphone from the list of WiFi connections I've attempted.
3) Flipped the manual WiFi switch on my laptop to Off and then back On again (to reset it)
4) Turned the Hotspot on my iphone back on
After that, when I tried to connect, it worked. Hope this works for someone else.

FireWire 400&800 (IMAC Core2) NOT WORKING after Upgrading to SNOW LEOPARD!

My FireWire 400&800 (iMAC Core2) are *NOT WORKING* after Upgrading to SNOW LEOPARD!
Any Solutions?
Thanks!
--Frank Strallents
www.SHOCKPROOFX.com

I'll try your suggestions....Thanks!
Recently, I try to Re-install Snow Leopard, unfortunately, still unsuccessful.
The Mybook Icon only appears if it is connected via USB.
After using Firewire and getting used to the speed...USB 2.0 is like a Corvette racing a Veyron...lol
I am not upset on these issues, it is normal for new OS to have these problems...unfortunately, even OSX is not invincible.
I'm sure Apple/Steve is on every Programers A*s for a solution.
I still think APPLE'S OSX will still be the future of Operating system!
For now, still waiting for the patch and hopefully soon.
Suggestions are still Welcome for a Solutions:-)
Frank
SHOCKPROOFX.COM

AE not working after upgrading to 802.11b/g/n AEBS

Similar Messages

Maybe you are looking for