AFP Service Crashed and Wont Start Again
I've got a 10.3.9 Server just running afp. It the AFP service just quit working yesterday while people were using it.
Now I can't get the service to start up Clicking the "Start Service" button in Server Admin does nothing.
serveradmin gives me this:
Classof2009:~ root# serveradmin start afp
afp:command = "setState"
afp:state = "STOPPED"
afp:status = -1
The only thing in the logs might be:
The server wasn't able to start (Unable to register IPC port)
But thats only happened a few times and not every time I try to start the server.
Crash Reporter shows nothing relevent either.
Ive tried rebooting, disabling and re enabling the network interface, and clicking the "Start Service" button over and over!
Help! I don't know where else to look!
Is there anything in system.log after trying to start AFP? You can view system.log with the Console.app.
Roger
Similar Messages
-
My screen suddenly turned black and wont start again
I was using my computer as usual when the screen suddenly turned off. It wont start again! I'm a musician and work with my computer!! Today I have a show and wont be able to use it!! I'm desperate Please, can anybody help!!
Thanks a lot!!!It sounds like you had a hardware failure. You can try doing a SMC reset, read the instructions carefully though as they cover multiple models of Macs. If that doesn't help I think it's time to contact a AASP. The AASP site is for the US, you will need to find one in Brazil though.
Good luck!
Roger -
Mini crashed and wont start 4 days after I bought it.
I have the mini 1.83ghz. As soon as I got it, I upgraded it to OSX.5. Ran great for the 4 days I had it. Today I loaded it to transfer files from my Windows laptop. While trying to transfer files, the computer hung up and then crashed. Now the it wont boot up at all. No spinning, beeps, or lights.
Any one have any ideas on it? or is my mini dead?Welcome to Apple Discussions!
When you say it won't boot and you get no spinning, beeps or lights, do you mean you don't even get the little power light lit up? If so, then there is no power getting to the logic board, which could be anything from a defective power source, to the power brick, or logic board itself.
I would unplug everything and move it to another location to make sure it's not a wiring issue with the power outlet you've been using, and test it again. If it's dead in the other location, call Apple and arrange to return the system, or pack it up and take it to a local Apple store to be looked at if you have one in your area. -
Mail crashed and wont start up
Hello
I hope some one can help. At work I use Mail for my emails, last night it crashed and when I tried to restart it the application will open but crashes immediatly again meaning I cannot access any emails or pick up incoming ones. What do I need to do to get it working again? I have restarted the machine a couple of times but to no avail. Please help. Thank youHi Mitchell&George, and a warm welcome to the forums!
Not certain, but this can fix myriad Mail problems...
Safe Boot from the HD, (holding Shift key down at bootup), it will try to repair your Disk Directory while the spinning radian is happening, so let it go, run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, then move these folder & file to the Desktop.
Move this Folder to the Desktop...
/Users/YourUserName/Library/Caches/Mail/
Move this file to the Desktop...
/Users/YourUserName/Library/Mail/Envelope Index
Reboot.
If that doesn't do it and you can afford to redo all your Rules, try these & reboot...
/Users/YourUserName/Library/Mail/MessageRules.plist
/Users/YourUserName/Library/Mail/MessageRules.plist.backup -
Mac os x yosmite 10.10.1 safari macbook crashing and wont start
Please help me my safari application wont start. every time i want to start it'll show safari quit unexpectedly.
You've installed the Genio malware. AdwareMedic http://www.adwaremedic.com/index.php will find and remove it for you, or you can do it manually by following these directions Remove unwanted adware that displays pop-up ads and graphics on your Mac - Apple Support
-
Why did both of my ipods crash and wont start up *** steve jobs
my ipod touch and my old 36g both crashed and burned today why
Same thing happened to my computer. Anyone know exactly what this means and if there is a fix?
-
Indesign CS6 crashes and wont startup again after reboot - iMac
Hello
I have a strange issue that has started in the last couple of weeks. If i restart or reboot my iMac my indesign will not open again. It tries to start to open ('loading image' appears and icon bounces in the dock) but always fails and gives an error afterwards each time (i will attach).
What i have done so far is the usual deleting of preferences, replacing default file and rebooting the machine again but nothing works.
The only thing that i can do to get it working again is to reinstall indesign from the disk (design & web premium). All other Creative Suite applications don't need reinstalling and work fine.
Has anyone else had this issue and if so how did they fix it as its bit of a pain having to reinstall indesign after each reboot.Im having issues adding the error log, here is the first bit of it though.....
Process: Adobe InDesign CS6 [262]
Path: /Applications/Adobe InDesign CS6/Adobe InDesign CS6.app/Contents/MacOS/Adobe InDesign CS6
Identifier: com.adobe.InDesign
Version: 8.0.0.370 (8000)
Code Type: X86 (Native)
Parent Process: launchd [123]
Date/Time: 2014-09-11 09:05:19.273 +0100
OS Version: Mac OS X 10.7.5 (11G63b)
Report Version: 9
Interval Since Last Report: 188705 sec
Crashes Since Last Report: 18
Per-App Interval Since Last Report: 186329 sec
Per-App Crashes Since Last Report: 14
Anonymous UUID: A7B9940A-3665-4D31-AF1D-3BFD1BF3E45B
Crashed Thread: 0 Dispatch queue: com.apple.main-thread
Exception Type: EXC_BAD_ACCESS (SIGBUS)
Exception Codes: KERN_PROTECTION_FAILURE at 0x0000000000000006 -
Hp dv6-3032tx shut down and wont start again
Hey guys,
My HP laptop turned off and I cant start it anymore. If I press the power button it starts for 2-3sec, you can hear the fan, the LED is on but it goes out. The LED on the side for the charger is on if its plugged in.
Already tried the reset. Probably the motherboard? How can I test it?
Thx for the help
CheersHello hiharu,
Welcome to the HP Forums! I hope you enjoy your experience!
I understand your computer will not start properly. I will do my best to assist you with this issue!
Based on your description, the motherboard is probably to blame. To troubleshoot, please try the steps in this HP document: Computer Does not Start
This document contains steps such as resetting the notebook and more, corresponding to the exact symptoms. I believe this document will resolve the issue. If not, I would contact HP phone support for hardware assistance. You can utilize this website to learn how to contact HP appropriately, based on your region: Contact HP Worldwide
Please let me know if you have any other questions or concerns. Thanks for bringing this issue to the HP Forums. Have a great day!
Mario
I worked on behalf of HP. -
IMac 27" 2011 - shuts down and wont start again
Hi everybody
I got my new iMac 27" intel i7 16 GB kingston ram for about a moth ago and worked perfectly until now.
Suddently it shuts down and when I tried to turn it on again, there was no response. I then waited about 30 minutes and tried again and it turned on. I thought it might be a one time accident, but 10 minutes later it shut down again.
When it shut down the first time it has been turned on for about 2 hours and I wasn't doing heavy work, just some surfing.
Anyone else who has experienced this and found i solution for whats causing this?
Are the any logfiles I can investigate to see what might happend?
RegardsAs Roger suggests, RAM is likely your problem. Have a look at this long thread:
https://discussions.apple.com/thread/2473276
Another workround is to try running on 12gb of the Kingston RAM and see if that solves the problem.
It seems that there is an issue with some makes of RAM and I believe that changing to Samsung RAM seems to fix things. -
Windows 7 system. I think I was running a beta of firefox 9. Please help! XX
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.org/kb/Safe+Mode
See:
*http://kb.mozillazine.org/Firefox_crashes
*https://support.mozilla.org/kb/Firefox+crashes -
HT4623 try to update and went black and wont start up again
try to update my phone now black and wont start up
Same thing happened to me. I took it to the Apple store and they told me they would be happy to replace the phone for me for $149.
<Edited by Host> -
Iphone stuck with apple symbol and wont start up
i updated my iphone and when it finished and went to reboot it just stays stuck on the apple symbol it constantly reboots and will never connect to my laptop i dont know what to do if anyone can help please do
Hi,
Luca224 & Ingo2711. Thanks for bringing this topic. on 29th Nov. I faced the same problem on my iPhone 3GS 32GB Firmware 3.1.2, iPhone stuck with apple symbol and wont start up. I have tried with 10 Seconds Sleep/wake-up button + home button to reset. But didn't work. Did google about an hour with many blogs. Finally I made a call to 3 iPhone care and spent 30 minutes and explained whatever I have done; iPhone customer care asked me to go to nearby iPhone service center in Sydney. BUT BY LUCK CLICKED ON iTUNE AND GOT THE OPTION FOR ONLINE FORUM FOR APPLE iPHONE. Many many thanks to Ingo2711 who has given the solution link and also thanks to Luca224 , who raised the issue. I feel, this is a common problem with iPhones those who using iPhone 3GS 3.1.2...... but try the link http://support.apple.com/kb/HT1808 and thanks to Luca224 & Ingo2711. PLEASE FOLLOW THE INSTRUCTION CAREFULY:
1. Verify you have iTunes 7.5 or later. Apple recommends using the latest version of iTunes.
2. Disconnect the USB cable from the iPhone or iPod touch, but leave the other end of the cable connected to your computer's USB port.
3. Power off the device (Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the the iPhone or iPod touch to turn off. _+(in my case - red slider didn't appear, but i pressed the Sleep/Wake button until the iPhone went off, finally it was just off... i was frustrated... tried 3 times with more patience )+_
4. Press and hold the Home button while reconnecting the USB cable to iPhone. When you reconnect the USB to iPhone, the device should then power on. +_( Do exactly as it says)_+
Note: If you see the message "Charging... Please Wait" or you see the screen pictured below, let the device charge for at least 10 minutes to ensure the battery has some charge and then start with step 2 again. +_(True ... for me it happened 3 times)_+
5. Continue holding the Home button while iPhone starts up. While starting up, you will see the Apple logo. +_( I was nearly frustrated at my 3rd attempet; my thumb was hurting as I was holding the home button for few minutes..... but finally it worked yahooooooooooooooooo...... suddenly changed my decision.... about going to 3/Apple service center)_+
6. When you see "Connect to iTunes" on the screen, you can release the Home button and iTunes will display the recovery mode message:
If you don't see the "Connect to iTunes" screen, then disconnect the USB cable from iPhone and repeat steps 3-6.
Because you must restore iPhone or iPod touch, iTunes will not recover data from the device, but if it was previously synced on the same computer and the same user account, it should restore a backup (if available). See document HT1414, "Updating and Restoring iPhone Software."
If you are still unable to restore the iPhone using this method, check Apple support for further troubleshooting and/or service options.
Note: If you sync both an iPhone and an iPod touch to the same computer, make sure you select the correct backup to restore your settings from (don't select an iPhone backup if you have an iPod touch and don't select an iPod touch backup if you have an iPhone).
**** ( BACKUP FROM YOUR iTUNES : MAC/PC; AS I GOT MY 95% DATA FROM THERE.... GOOD LUCK)******* IF IT WORKS PLEASE POST YOUR EXPERIENCE....*
THANKS -
Satellite A660 wont start again until i turn to safe mode
Just purchase toshiba Satellite A660: i tell the story to compensate closely to my answer, hopefully ..
I just purchase it new, run the insallation program for first use. When its up and running just within that day i noticed that it start to hang up when i hooked external drive for some program installation (adobe lightroom).
Its still fine but when i turn it off, it wont start again until i did turn to safe mode so that i could back up some of the files and run the recovery again.
This time on 64bit. When its finish its process, it works well for just a couple of hours.
It fell faster now thou, maybe because its on 64bit? ( any recommendation whether its 32 or 64bit) specs: i5 , 4ram, 1g ddcatd graphics , win7 home premium, ..
Now, when i turn it off it never start back again windows say.. start up repair. ..
I did let it run since this morning until now still they cant find whats the problem (i'm refering the loptop) .
So any idea on whats goin ?> It fell faster now thou, maybe because its on 64bit? ( any recommendation whether its 32 or 64bit) specs: i5 , 4ram, 1g ddcatd graphics , win7 home premium, ..
64bit Operating system is better if your notebook supports 4GB or more RAM.
Why? Because Win 32bit recognizes max 3.2GB even if more RAM is available.
This is 32bit limitation; no matter what OS it is; Linux, Win XP, Vista, Win7 etc
This is the reason why 64bit OS are so popular in the last time
Regarding the OS issue;
I recommend running a HDD recovery again... this means you should reinstall the OS usign the Toshiba recovery option;
Press F8 while powering up the notebook, Choose Repair my Computer, -> HDD recovery -
"My ipod is displaying apple logo and wont start up, hard reset leaves it the same, disc mode works but iTunes doesn't "see" it even if the computer does."
It worked two days ago fine, for two years, until I installed this newest iTunes update, then for one day it kept on freezing and going to apple logo screen mode, then today it only goes to that screen and wont start up at all.
I've tried the hold down two buttons hard reset, that doesn't help. I've tried disc mode... but iTunes doesn't "see" it even if the computer does.
This is a pristine ipod, never exposed to adverse conditions, never dropped, never wet, and it worked perfectly two days ago.
Can I factory reset it somehow? (considering itunes can't "see" it)
[Ipod classic 160gb less than two years old.]Looks like I might have found the solution on a youtube comment:
R.O:
"Plug into you laptop first, whichever set up you use that has iTunes, i know it won't read it, don't even open iTunes as of yet. Do the typical reboot "Menu +Center button at the same time" and hold it, DONT LET IT GO like we were told, when the apple pops up.. KEEP HOLDING IT it will make a new ding sound I've never heard before. and since its hooked to you laptop already an error message pops up and says apple will need to download something to repair your iPod. I when u see that that when i let reboot buttons go. hit ok on the laptop something downloads for like 20 seconds then the iTunes icon hops around when you open it it has a screen with an iPod classic on it and says "Software version blah blah, iTunes will check for an update on such n such date" AND FINALLY there's a "Restore" button. click that and you will be back to square one with your iPod. Renaming , adding all the music on it, but it will work again, finally. "
I had to do it twice, because my mac froze the first time, but its recognized it now and is downloading the software as we speak...
Now I've clicked the restore button and it's restoring... I'll post again if its a success, otherwise assume failure. -
Error 3194 still presist while restoring ipod touch 4g, just shows apple logo and wont start
Method 1: i have tried almost everything, 'hosts' file editing (adding and deleting that ip gs.apple.com thing)
Method 2: redsnow, snowbreeze,ireb (custom ispw and fetching thing)...
now my ipod is in dead case, it just gives apple logo and wont start.
Method 3: TS 3.0 and 1.0 checked, certificate xyz... uncheked from intertnet explorer-> internet option -> advanced -> security
Method 4: netsh xyz (comand) in cmd...
Please Help thank you.
"Details:
ipod touch 4g
ios 6.1 installed (lastly)
jail broken but deleted cydia from it
then tried to restore it always gave Error 3194,
then restored it from its backup file after that it didnt opened or just showed apple logo thats it."
my itunes on dignostic gives this report,
Microsoft Windows 7 Business Edition Service Pack 1 (Build 7601)
Hewlett-Packard HP xw4400 Workstation
iTunes 11.1.1.11
QuickTime not available
FairPlay 2.5.16
Apple Application Support 2.3.6
iPod Updater Library 11.1f5
CD Driver 2.2.3.0
CD Driver DLL 2.1.3.1
Apple Mobile Device 7.0.0.117
Apple Mobile Device Driver 1.64.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 001AB71808E6CBD8
Current user is not an administrator.
The current local date and time is 2013-11-29 04:19:21.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce 8400
**** External Plug-ins Information ****
No external plug-ins installed.
iPodService 11.1.1.11 is currently running.
iTunesHelper 11.1.1.11 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name: {BC8F9388-D244-4F12-92A3-A26318EE6C52}
Description: Broadcom NetXtreme Gigabit Ethernet
IP Address: 192.168.1.102
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
DHCP Enabled: Yes
DHCP Server: 192.168.1.1
Lease Obtained: Fri Nov 29 04:16:55 2013
Lease Expires: Fri Nov 29 06:16:55 2013
DNS Servers: 192.168.1.1
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: No
Firewall Information
Windows Firewall is off.
Connection attempt to Apple web site was successful.
Connection attempt to browsing iTunes Store was successful.
Connection attempt to purchasing from iTunes Store was successful.
Connection attempt to iPhone activation server was successful.
Connection attempt to firmware update server was unsuccessful.
The network connection timed out.
Connection attempt to Gracenote server was successful.
Last successful iTunes Store access was 2013-11-29 04:18:45.lllaass thank u bro, but none worked for me
i have tried all these methods n above which i mentioned before....
- Powering off and then back on your router.
- iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
- Change the DNS to either Google's or Open DNS servers
Public DNS — Google Developers
OpenDNS IP Addresses
- For one user uninstalling/reinstalling iTunes resolved the problem
- Try on another computer/network
- Wait if it is an Apple problem
in the end i went ot market n paid him 1.94$ and he restored it to 6.1.5... and said apple has closed other ios updation except 6.1.5 ...but still thank u soo much learned some new stuff from u...
Maybe you are looking for
-
Pls. Help me..
-
Help! When I try to down load the above message is what I get. I have uninstalled the last verision as it is giving me an error message also that is not running correctly!
-
My ipad was recently stolen. Is it possible to render it useless since tracking it is not an option?
-
Regarding IC Elimination data & Ownership Mgmt
Hello All, I was going through the file format example of Interccompany data present in user's guide which is as below: !SCENARIO=Actual !YEAR=2009 !PERIOD=January !DECIMAL=. !THOUSAND_SEPARATOR=, INTERCOMPANY DETAIL COLUMN_ORDER=ENTITY;PARTNER;ACCOU
-
Order of Installation of Flex Builder, SVG Viewer, XML Parser
Hello VC Experts, I am beginner. I need to create Reports in VC using BW Queries. I am Facing Flex application error while deploying the model. Is there any specific order of Installation of Flex Builder, SVG Viewer, XML Parser? Kindly help me to ***