AFP volume issues after 10.4.6

Having trouble with Adobe CS2 crashing after saving files and other applications having trouble with AFP mounted volumes, SMB mounts work fine except the application (in this case) scans all attached server volumes for name & ip resolution, but the names are getting the first letter chopped off and not finding the respective servers. This did not happen with 10.4.5.
NetInfo edits help the AFP side, but the server names are still being resolved incorrectly for SMB volumes.

Hi A Brody,
(Btw, you wern't in that Jaws movie were you?)
Yuk-Yuk. . .
I know about the AFP case sensitivity with regards to Windows servers. If the name of the volume is all uppercase, the AFP translation is all uppercase letters.
If the name is all lowercase, the AFP translates the name upper/lowercase (capital first letter only).
SMB mounts are all capitals, no matter how the shares are named. That's an easy way to tell if I have an SMB or AFP mounted share on the Mac.

Similar Messages

Volume issues after ios 5.0.1 update

i recently updated from ios 5.0.1 to 5.1 and today i observed that the volume went low while listening to songs and i did a hard reset and now things have started to work fine.but what is the permanent solution for this?any one who is facing this issue?

While wifi connection is never good on ipad according to my experiecne, the situation is worsend after ios 5.0.1. It takes approximatley 2 to 3 minutes for me to connect to the home router, (it took 30 secs at most in the past). When I go out for outdoor wifi, the hotspots of some internet service providers can never be connected, the refreshing circles keeping spinning for 3 to 5 minutes and nothing happen.
The bottom line is, battery life seems to run longer than before, but I don't think it is an acceptable trade-off.

Volume issues after update to 4.02

My ipod will play audio throught the headphones jack, but when i remove the headphones the ipod still says that there are headphones connected. I've tried resetting it and restoring it. How can i get my external speaker to work again?

I just had this happen and I came on here to figure out how to get it to work. I went to the settings control and then went to general. I reset all settings and the volume started to work. Maybe try it again, or turn it off and on.
Message was edited by: KariT
Message was edited by: KariT

IPhone system wide audio volume issues after iOS 5 update...

I have an iPhone 4 (CDMA) that I updated to iOS 5 on launch day. I didn't notice it at first, and maybe it's just my imagination, but the volume of everything on the phone seems to have gotten a bit lower. Not only music, but also all ringtones, SMS tones... everything. I checked to make sure all the volume sliders are up; they are. I also made sure volume and accessibility settings are set appropriately; they are as well. I'm stumped on this and unfortunately I don't have another iPhone running iOS 4 to test this with. I have searched the forums here and on Google to no avail; it seems that either people haven't begun posting about this yet, or it's not a problem with most users. Is anyone else noticing this and if so, is there a workaround?

Hey there,
Thanks for the tip. I tried it, but it doesn't seem to have made any difference. I noticed a glitch a few days ago - when I unlocked my phone and went to listen to some music (through an ihome), there was barely any sound. I touched the volume slider (which was already at max volume) and it shot back up to normal. I still think that ringtones/smstones are softer than iOS 4 though.

Volume Issue after installing FCS 2

Hi I recently got Final Cut Studio 2, I previously had Final Cut Studio 1. I have two hdd in my PPC G5 tower and I wanted to install Final Cut Studio 2 on my secondary drive (which is running Tiger), b/c I was working on a project in FCP 5 on my primary HDD (running Leopard). All the programs worked on the secondary drive but when I restarted and booted up the primary drive I tried opening the programs from that HDD while running Leopard and all the programs won't launch. I really can't afford to install FCS 2 on that drive B/C I do not want to replace FCP 5 at the moment. Any suggestions on why this is happening?

YOu need to run the applications from the drive they are installed on. If you installed FCS 2 on the TIGER drive, then you need to be booted from TIGER in order for it to work.

Time Machine to AFP volume is extremely slow after 10.5.2 update

I remember the time, after I have just installed the very first version of Leopard, when Time Machine was working with close to physical speed of my wireless network. Incremental backups would take less than a minute.
Comes 10.5.1. Time Machine became slower, but still tolerable: it might take up to 10 minutes to do an hourly backup.
Comes 10.5.2. Now Time Machine might take a couple of hours to do its "hourly" backup! 99% of the time it spends backing stuff up - when it shows the progress of the backup. So right now it says it's backing up 34.1 megabytes, and then it stopped at 1.4 megabytes, spent there about 15 minutes. Then it continued to about 9.5 megabytes, spend another 20 minutes there, without any progress, no CPU usage, very little network usage. Then it progressed to about 10.5 megabytes, and stuck again. Now it's at 15.2 megabytes, and been there for about 10 minutes already.
I use Airport Extreme base station with 802.11n at 5GHz, and the backup volume is on my Mac Mini, connected to AEBS via an ethernet cable, and during the phases when Time Machine gets stuck, I tested how the network works from my MacBook Pro, which I'm trying to backup to Mac Mini - constantly getting about 8-9 megabytes per second transfer rate, so clearly it's not that my wireless network is experiencing issues. Besides, the same problem persists even if I plug Ethernet cable directly into my MacBook Pro.
I've cleaned all caches, repaired permissions, repaired all volumes, rebuilt Spotlight indices on both my MacBook Pro and in the backup sparse bundle. The only thing it solved is insanely long "Preparing for backup" issue, but it DIDN'T solve the slow backup I have just described.
For comparison: rsync takes about a minute to do a full sync of my entire hard drive to the same AFP volume. Apple Backup 3.1.2 takes about as much. Time Machine - hours. I fail to even begin to imagine what in a world might they be doing there, spending this much time copying 34.1 megabytes of data over the network.
P.S. As I finish writing this, the backup progress is still at 15.2 magebytes. About 15 minutes now. A little over an hour now and not even half of the 34 megabytes is completed.
Message was edited by: Farlander
Message was edited by: Farlander

Is it slow wireless LAN behavior affecting Time Machine? Check out the third page of this thread, specificallly the post by John Albergo about "delay_ack."
http://discussions.apple.com/thread.jspa?threadID=1394485&start=30&tstart=0
It helped me a lot.

Problems with searching on AFP volumes

Hi,
our clients (Macs with Lion) can't find the files on the AFPs volume when searching.
The first days after I had installed Lion Server it worked fine - no it is getting more and more worth and many times no files are found even if there are many.
Who can help me?

Having the same issue. Network Share on attached Promise Pegasus R4 Raid (via Thunderbolt) is not searchable. All common practices to reset the Spotlight index failed. Mac Mini with OS X Lion Server 10.7.2

Volume issues with GE60 Apache Pro-003

I recently picked up the new GE60 Apache Pro notebook, and I've been running it for about a week now. I should of course mention that I also did a clean windows install after adding an SSD to the system (and now can't figure out how to add back that cool MSI panel that was there when I first got the system).
Anyway, I've noticed that there seems to be volume issues with the system no matter WHAT kind of settings I tweak, or drivers I try to use. With all sliders up at maximum, the volume levels still never seem to surpass around 50% (from observing the volume gauges in the Windows Volume mixer panel). My previous notebook's speakers put out significantly higher volume, and was also able to put out far more power to my headphones (Audio Technica ATH-M50).
Any possible ideas for the cause and solution to this problem? Thanks in advance, and let me know if there is anything else I need to mention.

Quote from: darkhawk on 02-April-14, 20:44:14
What are you using to gauge the '50%'? MP3's? Windows sounds? or what?
Pretty much everything. Music, games, online videos... According to the volume mixer, the audio levels never seem to pass 50%. The grey bar bounces to the peak, but the green bar never seems to pass the 50% level. It's as if there's some sort of limiter in place I'm not aware of. And since I reformatted the notebook as soon as I got it, I was never able to see if the volume control worked correctly before the reformat.

Has Anyone sent the iphone in for repair for the low volume issue ???

I called apple last week and spoke with a level on support agent. After he could not solve the volume issue they sent me to level two. the level two tech took the call and told me right away that they were going to send me a new phone. I give him my credit card as a deposit so they would send a new phone and when I had the new phone I could then send the old one back. Well after a few days I called to check on the phone and found out he never placed the order and now they say they want to send it for repair some place in Texas. They did offer the rent me a phone for 29.00 while I wait for repair. I told them no rental for me. How bad is that, a hardware issue and they say they are going to send a new phone and never do then they offer a repair and to rent me a phone. I was wondering if anyone had sent in the phone for this issue yet. I do not think I am going to send it in and I think I am going to get my refund while I still can. I just thought I would check to see if anyone had sent the phone in for repair yet and how it worked out.
Andrew

How are any of us (Apple users just like you) supposed to have any idea?
We weren't there. We don't know the specifics of what happened to your iPhone.
Ask the store that repaired it.

After updating my mac book pro to the osx yosemite.am getting some issues after starting up.a soon as it gets on the destop the screen start blinkingand i cant do anything

After updating my mac book pro to the osx yosemite.am getting some issues after starting up.as soon as it gets on the destop the screen start blinking and i cant do anything.Please help me!

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Volume Issues - Too Loud & Too Soft

This is a problem I've had for awhile now. It's getting unbearably frustrating. Volume issues, where the default value for sound ranges outside what the iPhone should be capable of doing. So for example if the volume goes from 0% to 100%, my phone will be completely random and range from -50% to 150%.
How can it be less then 0% you might ask, when moving the slider mid way the volume is completely off and any lower doesn't make a difference, then I'll receive an email notification and BAM the volume goes up 300% and it's so loud it feels like the speaker is going to explode. This problem happens at any time but mostly after or while using headphones or car bluetooth.
Example of my issue in action, I'll plug AUX in the car into the phone, play music, driving along, randomly goes to half volume. I'll turn up the stereo to compensate, one minute later I'll get an email and the volume resumes to normal operating volume and I almost sh** my pants in fright.
Another example is I'll be watching a video late at night before bed on youtube or something with the volume all the way down, then the next morning my phone alarm will not sound or it will but insanely softly. The work around for this is to play music right before locking my phone with the volume up all the way. Just move the volume up all the way, play > pause and there you have it, volume working agian.
And one last example, randomly it goes really really loud. Like how is this possible loud. I'll dial a number and when pressing the buttons instead of a beep beep beep. I get fog horn BEEEEEEP BEEEEP BEEEEP. But as soon as the call starts the volume sets itself back to normal. Kind of like how when playing music without head phones with volume on max sets it back to normal.
Things you should note:
Ringer volume has been locked to maximum, but quite often won't abide by this rule.
I've reset the phone and setup as new iPhone, problem still occurs.
Please don't give a solution like, "Have you checked your sound volume in settings". I'm not stupid.
Also, please don't give a solution unless you understand the difference between "Notification and Tone Volume" and "Media Volume".
Other then that. Please help, this is driving me mental.

I recently did the last firmware upgrade for my ipod nano 5th gen and can't set the maximim limit.
It can be set, but wont stick and I can still go above the limit.
Did something break with the firmware upgrade.

MacBook Pro Volume Issue

Hi, All.
I have a MacBook Pro with a 15" monitor, 2.8 GHz Intel Core 2 Duo processor. Currently working with OS 10.6.8.
I'm not sure since when, but I'm having this issue:
Even though I turned the volume off, every time I shut down and boot up, or restart, the machine, the volume automatically goes up to about the middle of the indicator. I know it may not be a critical issue, but sometimes I forget about the volume problem, the loud sound makes me jump and it's quite annoying. (Especially in public.)
I'm wondering if anyone else is experiencing the same problem and if there is a way to solve the problem.
Any information will be appreciated.
Best,

Hello, tjk. Thanks for your reply.
After you told me, I did PRAM resets several times, but unfortunately I'm still having the same volume issue.
I've been doing online researches for while to find the solution for this problem, but I don't see any other people having the same problem. Probably this is a new issue?
Thanks.
drbonzo

AFP Connection Problems after Server Security Update 2009-006

After installing the Security Update 2009-006 on the Server, we have Problems to mount Shares from two differnt AFP-Servers on the Client.
The Client and the Server have a binding to AD.
The Client can connect to Server1 via AFP.
But after this, the connection to Server2 shows the Volumen List from Server1!
Same Problem when the first Connection mounts Server2 and then Server1.
I tried the second connect with DNS-Name and IP-Adress.
There is no Problem when i am useing SMB.
Have anyone a Idea or the same Problem?
Thanks
Sven

Hi kapteyn,
If you are having issues connecting to your WiFi network from your MacBook Pro after a recent security update, you may find the troubleshooting steps in the following article helpful:
Apple Support: About Wireless Diagnostics
http://support.apple.com/kb/HT5606
Regards,
- Brenden

Mount AFP volume error [-5002 (AFP Bad UAM)]

After reading many complaints about AFP in Leopard, I just have to ask again if anybody has a workaround for the “Connection Failed” error -5002 when trying to mount an AFP volume in Leopard. Does anybody have any more info about fixes, workarounds or info about this problem with Leopard? And what is UAM??

UAM == user authentication method
Each AFP server, depending on its version, will have a set of UAMs that it supports by default. These are essentially authentication capabilities such as "no authentication", "cleartext passwords", "kerberos auth", etc. There are several others.
That error code would imply that your client is trying to authentication in a way that the server doesn't know how to handle. Is this another Leopard box you are trying to mount?

Elite Pro, CMSS-3D not working and other issues after driver update

DElite Pro, CMSS-3D not working and other issues after driver update <font face="arial,helvetica,sans-serif" size="4">Elite Pro CMSS-3D control (on I/O console)no longer controls CMSS-3D.
The only time it works is if the original drivers are installed from the installation CD.
ANY other drivers stop the control on the Elite Pro I/O console from having any effect on CMSS-3D.
Also at one time when I cotrolled volume, CMSS-3D(original drivers), EAX and Crystalizer from the Elite Pro I/O controls then I had on screen display of said control that was being moved(on I/O console).
Now regardless of what drivers are installed, there?are no longer any on screen indicators.
The indicators looked like the ones that show when using the remote controller.
Anyone have any ideas?

Hello friends, if any body have problem with "Creative Sound Blaster X-Fi series Driver 2.8.003" then you can download previews "Creative Sound Blaster X-Fi series Driver 2.8.0008" from above direct Links :
http://rapidshare.com/files/252388832/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part0.rar
http://rapidshare.com/files/25239047/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part02.rar
http://rapidshare.com/files/252397989/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part03.rar
http://rapidshare.com/files/252397990/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part04.rar
http://rapidshare.com/files/25239799/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part05.rar
http://rapidshare.com/files/25240785/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part06.rar
http://rapidshare.com/files/25240787/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part07.rar
http://rapidshare.com/files/252405003/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part08.rar
http://rapidshare.com/files/252408540/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part09.rar
http://rapidshare.com/files/252408542/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part0.rar
http://rapidshare.com/files/2524409/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part.rar
http://rapidshare.com/files/25244020/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part2.rar
http://rapidshare.com/files/2524402/__Creative_Sound_Blaster_X-Fi_series_Driver_2.8.0008__.part3.rar
http://rapidshare.com/files/25244022/[email protected]7.254.6.0

AFP volume issues after 10.4.6

Similar Messages

Maybe you are looking for