After a power interruption, iMac no longer connects to wifi using time capsule. IPad connection to wifi remains intact.
I am prompted "the network (network name) requires a wpa password." after inputting my password, I have no success. Network status is on but is not connected to a network.
Hi, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.
Also, turn off IPv6:
System Preferences » Network » AirPort » TCP/IP tab » Configure IPv6
Or whatever Interface you use.
Similar Messages
-
Unable to connect to internet using time capsule
Over the last couple of days I have run into a peculiar problem. I am able to connect to the internet when I connect the ethernet cable directly to my computer. Now when I use time capsule to connect wirelessly, the connection either does not get established or if it gets established fails after a few mins and I am unable to browse the internet. I have noticed this problem especially after Mac OSX 10.6.3 update. I did not have this issue earlier. I am not sure if this is the root cause but would surely like some help.
This behavior may indicate that you are picking up wireless interference from cordless phones, another wireless network, security system or other electrical device. It's hard to pinpoint the exact cause.
Suggest that you start by downloading iStumbler and using the application to display your signal strength and noise on your network. What values do you see for each of these?
Also look at any other networks to see if they might be using the same channel or an adjacent channel as your wireless network. If so, change the channel on your wireless network so that it is as far away as possible from other networks.
If you have cordless phones, turn them all off for at least an hour when you can to see if your network performance improves.
Interference robustness often does more harm than good. Try turning it off. However, if you find that your network performs better with it on, that is an almost sure sign that wireless interference is occurring on your network.
You won't be able to do anything about cordless phones at your neighbors (my neighbor...across the street...can knock me off my wireless network if he is in his front yard with his phone and it rings). Users far underestimate the effect that cordless phones have on their wireless networks.
Post back with your findings when you have tried a few things. -
Can I use time capsule without setting up internet connection?
Yes, you can connect to your current router using Ethernet (highly recommended) or wirelsss only.
I -
Delayed Connection to Internet using Time Capsule on a network
I have a Time Capsule connected to a Verizon Actiontec DSL modem/router. It is connected in bridge mode.
The problem I am having is that when I first access the internet it takes a long time, then after the first page loads all the subsequent pages load fast and well. It is almost like there some connection issue at the beginning that the software eventually corrects.
Also, when I bring up the Airport Utility, if often shows at first the Internet as "amber" and "disconnected" while the Time capsule is green. But I know if I access the DSL/modem at 192.168.1.1 it always shows it is connected.
Has anyone heard of such an issue before, and how it can be corrected?
Thank you.what version is your TC?? A1xxx from the base and firmware revision.
Or just post the picture from airport utility. You can pick up the model from the full summary page.. hold down the option key and double click the icon of the TC in airport utility.
The later firmware on Gen1-4 is less than robust.. downgrade to 7.6.1
The 7.7.3 firmware on the Gen5 is also issue prone but more the hardware can have issues.. if the actiontec modem has ethernet ports set to auto the TC may not negotiate correctly.. Try and set it to 100mbit full duplex .. if that is not possible use a crossover cable or a small 10/100 switch between the TC and the modem.
I have a Time Capsule connected to a Verizon Actiontec DSL modem/router. It is connected in bridge mode.
Is "It" the TC or the Verizon as it is unclear exactly which you are bridging.. I am guessing the TC. -
I can't connect to internet using Time Capsule router.
My hard drive recently died. I took the iMac to the Apple store and had a 500 GB hard drive installed. I disconnected my Time Capsule so the Apple rep could restore my data. Now when I try to reconnect to the internet via Time Capsule router, it won't connect. The cable modem is fine, and the Time Capsule's status seems OK with the green light. It even seems to be backing up OK. I don't think I did anything differently, other than unplug it in order to have the Apple rep restore my data. Any thoughts out there?
It sounds like the cable company neglected to mention to you that you must completely reset the modem whenever you change the device that it is connected to. That's because the modem "associates" with a device and "remembers" the settings.
If you then change devices, the modem will "look" for the old device that was connected to it and it will of course not "find" it, so it won't connect.
That's why you need to do the complete sequence that I provided.
If you still cannot connect after the complete reset, then you may have a defective modem. I'm not trying to pick on the cable company....and yours may be an exception...but the last time my modem was having problems, the provider kept insisting that "everything looks good". But, they always say that.
I turned the modem off and called them back an hour later and they still said "everything looks good".
An Ethernet cable has a slightly wider plug than a phone cable. If that's the only connector on the modem, then it must be the right one. Ethernet cables do fail. You might want to check your cable, just in case. -
New Time capsule not connecting to wifi, New Time capsule not connecting to wifi
I just got a 2T time capsule, and it picked it up on the wifi the first time, and I went through and clicked what I wanted for it, but now it's not getting picked up on the wifi. It's about as useful as a brick right now.
I'm on an imac and I just want to use it for backup, and not a router. I want to do half for time machine backup, and then half for movie files to access from the time Capsule on my iMac.Are you using join a wireless network on the TC?? This is a mess..
Please describe the whole existing networking.. and how you are trying to fit the TC into it. -
Does anyone can use time capsule without connection breaks?
if I backup more than 100 mb, the connection via wifi breaks and i can not find the time capsule. either i have to restart computer or time capsule. i use mac lion. time capsule 1 st gen, 500 g
Ok .. this is pretty easy.
You plug the WAN port on TC into the N900 LAN port by ethernet.
Open the airport utility on the Mac.
Simply allow it to automatically setup and it should select bridge mode.. if not just jump in at the end .. click on the edit under the summary and go to the network tab and select bridge.
Then go to the wireless tab and make sure you are creating a wireless name.. you can give it the same name as the N900 same security same password.. this is called roaming network.
Or use a different name.. use short, no spaces and pure alphanumeric.
I have given a different name to 5ghz.
It will not matter which wireless you connect to but the TC is faster on the 5ghz for backups. -
After updating my iTunes it no longer acknowledges that my iPod or iPhone is connected so I can't update my music.. I have followed all of these steps and everything is working fine but this new version of iTunes isn't recognizing my devices. Any advice?
I have the same problem. Running Win 8 64Bit, updated to latest ITunes and now will not recognize phone or pad. Followed all advice from Apple (uninstall/restart/re-install, all in exact order) ... nothing. Spoke with Apple tech and walked through the whole process, but no resolution. Tech was trying to be helpful but has no way of addressing issue.
-
I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer. So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only. How to I make the connections?
Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC. I've had the Airport Extreme for a year or so. The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems. I was expecting the same with the TC. But the instruction that came with TC say to connect the printer to the TC via USB...which I did. And the print function worked perfectly but nothing else. In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else. I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way. But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems. I may try that again...and see if I can get all print functions with just the TC connected
As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this. Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup. I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart. But now I find that the connection only lasts for a short time. If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct? Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
Thanks... -
Time Capsule "Server Connection Interrupted"
For the last 2 months I get this Pop Up every Couple of Hours on my iMac. I have a Time Capsule & my iTunes Library is on that Network Hard Drive.
"Server Connections Interrupted" and shows the Hard Drive in my Time Capsule (iTunes).
I am running latest Version of Lion.
I am connected from iMac Ethernet to Time Capsule.
I have the Time Capsule Drive Set to Login when my Mac Starts Up.
But here's the funny part. My iTunes Music will be Playing perfectly when this Pops Up. No skips, Stutters. Nothing. So it does not interfere with anything working.
I would like to Post the Error but I forgot how!I have just installed a new 4th generation Time Capsule, and have the same [what I thought initially was just a nuisance] 'Server Connections Interrupted' popup window appearing very frequently.
Here is the Popup window:
Worse; when I began the process of backing up 105GB of data from my NAS RAID 1 set up to the new Time Capsule (TC), the copying process is failing part way through [typically deep down in the Folder Structure] which as you can image is a real pain, a hopeless situation really…
Here is the Copy Faiure message:
The TC setup is simple, WiFi turned Off, DHCP, Bridge Mode. Connected directly by Ethernet to iMac and the NAS, and the WAN Ethernet port to an AirPort Extreme.
I also note a strange entry in the TC Airport Utility 'Logs and Statistics'…
Every five minutes, there is a Severity:5 message, an AFP Login, instantly closed?
Feb 25 12:13:56 Severity:5 AFP login OK from Robert [email protected].
Feb 25 12:13:56 Severity:5 AFP session from Robert [email protected] closing.
Feb 25 12:18:57 Severity:5 AFP login OK from Robert [email protected].
Feb 25 12:18:57 Severity:5 AFP session from Robert [email protected] closing.
10.0.1.2 is my iMac
What on earth is this log about, is it related to the failure of the copying of the backup files from NAS to TC...
I am in a desperate situation right now, since I am unable to continue with the backup and restructure of iPhoto and iTunes libraries, which are all resident on the NAS RAID 1 setup.
Am replacing all of the Ethernet cables involved, incase this is simply a 'bad connection'.
Would appreciate some feedback from anyone who may have cracked this issue...
Take note Apple, this is awful!… All my other stuff, prior to this incident, an Airport Extreme, an older Time Capsule as WiFi extension and storage, Airport Express, Macmini, works like a charm…
Robert -
My new Time capsule 802.11n (4th generation) remains saving after a long time (3 weeks) but there is no backups files in time machine. It seems that it is working without results. What should I do?
Hello, no experience with TC, but...
Have you looked through Pondini's extensive TM help site?
http://Pondini.org/TM/FAQ.html
http://pondini.org/TM/Troubleshooting.html
Can't imaging something not being covered there. -
After a power outage Apple TV can't find date and time - just keeps spinning on that screen. Tried powering off Apple TV, the computer, and the router. Tried to restart Apple TV. Tried to restore Apple TV, but it got stuck again setting time/date.
Welcome to the Apple Community.
Along with the things you have tried, some have had success setting the location to the US. -
G4 imac and time capsule wireless connection
I have a dual band time capsule working wirelessly with 3 macs all intel (24 iMac, mbp 13, mb 13) with no issues. I was trying to connect a 17" flat panel G4 to the same wireless network on the time capsule and it fails to see the network.
When I type in the network name and password (WPA) it comes back with "encryption method not supported by the wireless network". Although all the others macs are working on this same network using the same encryption, the old iMac refuses to play nice. Is there something else I've overlooked?
This G4 has been on a various wireless networks over the past 5 years. It is running 10.4.11 and I know it will not support time machine, but still hoping it can share the wireless network.
ThanksJames,
You need to configure the Time Capsule to "join" the wireless network that is being provided by the Netgear router. The Time Capsule will connect using wireless only in this type of configuration.
Then, the Netgear, Time Capsule and your computer will all be on the same wireless network and you will not have to "switch" networks to access the Internet or back up to the Time Capsule.
Before we make any changes, we want to make sure that you understand that the Time Capsule will not perform any routing functions when it is configured to "join a wireless network".
The Ethernet ports on the Time Capsule are not enabled in this setup, therefore you will not be able to use Ethernet to back up to the Time Capsule. Backups will be over wireless only, which is significantly slower than an Ethernet connection.
This setup can be tricky because you must know the exact type of wireless security that the Netgear router is using in order to provide the correct settings to the Time Capsule.
If the Time Capsule does not receive the correct settings during setup, you will receive a message that there has been an error and you must start all over again with a complete factory default reset of the Time Capsule and try again.
So, before we go any further, we need to ask....what is the exact type of wireless security that your Netgear router is using? -
The following error pop's up as an [OK] dialogue box after logging in the iMac,
There was a problem connecting to the server "Time Capsule".
The share does not exist on the server. Please check the share name, and then try again."
As it happens, a connection to the Time Capsule is established usually, anyway. On occasion it doesn't.
I have a Volume, Data, on the capsule, which similarly, usually mounts, but occassionally doesn't, with access permissions denied.
Any suggestions on how begin to work out how to achieve networking seamlesness?First, restart the Time Capsule by disconnecting the power adapter and reconnecting it. If other devices on the network can see it, you can skip this step.
From the menu bar, select
▹ System Preferences ▹ Network
Click the lock icon in the lower left corner of the window and authenticate to unlock the settings, if necessary. Click the Advanced button, then select the TCP/IP tab in the sheet that drops down. Click Renew DHCP lease.
Try again to back up.
If you still can't, open the Time Machine preference pane and delete the TC from the list of backup destinations. You may have to unlock the settings by clicking the lock icon in order to do this. Then add it back. -
Time Capsule not connected to Ethernet?
Hello,
I walked in to my office two days ago and the amber light was blinking with an occasional green (on my Time Capsule).
The reported error was that the ethernet was not connected. It was. I ultimately disconnected the ethernet cable from my Time Capsule and connected directly to my iMac. After some configuring issues I was on line. Did what I needed to do and shut down.
Next day I decided to try powering down the Time Capsule and re-connected the Ethernet cable. Everything worked fine just like it has for well over a year now.
I figured maybe the cleaning crew bumped the power and everything was fine.
No dice.
Came in this morning and the Time Capsule is blinking amber again (with an occasional green) same issue. "no ethernet connected."
Now I am connected directly to the IMac and asking for help.
Please.
Thanks in advance for your help.
POn our TC, the TC shows a green light even when it refuses our computer/device wireless connections and says the password is invalid. However, I left the house for three hours and am now on my laptop and it is apparently working normally. I plan to watch it very closely for the next week and see what happens.
I have read on here (and other Mac-centric review sites) that TC's are very unreliable, have slower than average wireless connections (and short ranges in apartments, especially through walls/several rooms), and fail within 18 months -- all of which is considered "normal" lifespan by Apple (as confirmed by the Apple employees at the San Diego Store in Fashion Valley).
I don't plan on purchasing another TC, and likely not even an Airport extreme. I will look at buying a more reliable wireless router with stronger (farther) connections and connection ranges. I love apple products and have used them to the exclusion of others for over 15 years, but this is really annoying (and my friends have much better wireless networks!).
Maybe you are looking for
-
How to find out who imported last support packs
Hello I wander who imported last support packs on the system ILS (SAPKB70014 and SAPKA70014). How to find that out. The transport directory is common for many systems
-
Will somebody at Adobe please contact "Apple Care" and observe what REAL tech support is all about?
-
Install J2SE in Solaris 8 in Sparc
Pls help ! I need instructions on how to install j2sdk-1_3_1-solsparc.sh file. The instruction in tutorial is not clear. Thank you in advance. James
-
Webservice creation for consuming BAPI
Hi, I want to create a webservice for consuming data from standard sap functional module for mobile integration. Can someone explain his experience to reach this requirement? My main requirement is to design a webservice which can consume SAP B
-
Hello all, I am preparing myself for a career as a Oracle apps functional consultant in supply chain domain. Based on your experience what is the best way/process to get ready for this? Do I need to get trained in some institute or else buy some book