After client copy and import export, WebUI not functioning

Hi Experts,
We have copied the client MKH300 into the client MKH305. The client
copy was performed using SAP_ALL authorization.
After the client copy a client compare was performed and several
differences were discovered. BDLS was run and a custom program was run
to copy custom tables from MKH300 to MKH305. This program has been run
in several other client copy cases and there is no issue with it.
When logging into the WebUI in client MKH305 an error message is
displayed in the application log:
"An exception has occurred during program processing"
(Please see attached screen shot)
When looking into the details the following text is shown:
Diagnosis
An exception occurred during request processing. This was handled
centrally. It changed the program flow and the result of the request
probably contains errors.
Procedure
Contact your system administrator.
Procedure for System Administration
Activate checkpoint group BSP_WD_EXCEPTION_DISPLAY. To do this, use
transaction SAAB. If the error recurs, further details are displayed.
When the check point group was activated there was no more information.
The links in the Homepage are not correct even though the business
roles, config keys etc look the same between the clients.
Much customization seems lost for the WebUI although when comparing the
two clients' customization for the WebUI they seem identical.
The client MKH300 works fine so the intention was that MKH305 should be
an exact copy of that client, but that did not happen.
Could you please help me out.
Thanks!
Nagaraju

they are included in the xe server install ...you could try copying the executables but maybe that wont work if all the libraries arent present
failing that install the regular oracle client

Similar Messages

Differences between Remote Client copy and Client export and Import

Dear All, I am new to SAP. Please let me know the Differences between Remote Client copy and Client export and Import. Any response is greatly appreciated. Thanks a Million

Hello Mallikarjuna,
Follow the below note,
https://service.sap.com/sap/support/notes/552711
which describes the answer to question - Which is better or faster, a client transport or a remote copy?
Basically client transport would be preferred if the network connection between the source and target system is slow.
For more help,
http://help.sap.com/saphelp_nw70/helpdata/EN/69/c24c0f4ba111d189750000e8322d00/frameset.htm
Regards,
Debasis.

SAP* not authorized after Client copy

Dear All,
Here's the scenario:
1. Created a new logical system for a new Quality client 230.
2. Created the new client 220
3. scheduled a test remote client copy from the new client, source Production. (Successful)
4. Scheduled the actual client copy to run last night.
5. Today morning, I'm logging into the new client with SAP*, it prompted me to change password.
6. I want to look for the client copy logs (SCC3), but getting "not authorized"
7. Checked all other transactions, all giving "not authorized" error
Any help would be appreciated. Thanks in advance.

Dear Reza,
Better to go for Client Export Import process . This is what SAP reccomends for coping clients between
different systems ( Like from Production to Quality ) as the remote client copy has many
disadvantages..
For this 1 ) you should get the downtime of production system and do the client export process .
SCC8 . See the logs at scc3 .
2) Copy the datafile and cofile to the Source system
3) Import it usting stms_import .
Monitor the logs as the logs will be grown massive and make sure enough space is there.
4) After client copy , go for post processing ( scc7 ) .
Hope you are clear and feel free to get back if any doubts.
Regards,
Nibu

EWZ5 unlock users after client copy does not work

Hi All
I have following problem, i made client copy and i locked user in EWZ5 on both systems (source and target). Than I made client copy with profile SAP_CUSV (customizing with variants). The problem is that after the copy i am unable to unlock users on the targat client in EWZ5. I see users locked in the transaction but when i click unlock than no one is unlocked (result like there are no locked users) and users still remains locked (i tried to log on). On source system unlocking was working ok.
Any suggestion are highly appreciated.
JM

Hi Josef,
Did you checked syslogs? You can also execute the sql statement, below, on sqlplus;
update <owner>.usr02 set uflag='0' where bname='EWZ5';
commit work;
Best regards,
Orkun

Unable to find product categories after client copy

Hi all,
We have copied clients from an existing ones for both SRM and ECC. After client copy we have followed standard procedure after client copy i.e.
Run transcation BDLS
created new RFC connections
changed attributes using the Attributes replace report
created new distributon model
maintained CRM parameters
maintained new site attributes in SMOEAC transaction
maintained entries in table TWPURLSVR
however , when i try to create a shopping cart, I cannot see any product category. The extended attributes for product category point to new ECC client becuse we have run the attributes replace report.
however in the product category table , COMM_CATEGORY , the product categories listed are all for the old ECC client
When i tried to load the Object DNL_CUST_PROD1 using transaction R3AS in SRM and tried to pull from new ECC client , it is in runing status for a long time and new categories with new ECC backend reference are not being replicated in the SRM.
Can you tell me why this could be happening ? How can i get the product categories from new ECC backend into my client?
Regards,
Mangesh

problem solved
i was using wrong parameters in BDLS

Change Myself system in RSA1 trx after client copy

Hi,
I have installed SCM 2007 system.
As post-processing step i have configured myself system in RSA1 trx in the 001 client.
Now, i want to perform client copy and use that new client 100 as Prod client. What are the steps required to change myself system to point to the new client?
Please help.
Regards,
Chintan

HI,
As logical systems are used to define you can use BDLS to convert them after client copy.
Go through :Note 325470,325525.
Thanks.

BI-RFC problems after client copy

Hi all
Client copy was done and after that when I tried to load data in BW, it ran for long time and finally showed cancelled in SM37. When I checked the source system in RSA1, it gave two messages.
1.Incorrect IDoc type ZSAC008 in the ALE definition of the source system RSAR373
2.Result of the destination check: Password logon no longer possible - too many failed attempts RSAR375.
In long text of message 1 suggestion was to enter IDoc type ZSAB003. In SM30 for Message Type RSSEND Basic Type ZSAB003 Release field is empty. Is this error because of this? After client copy is there a way to restore the settings back to how it was set initially in the development server? Basis told ALEREMOTE & BIWREMOTE are not blocked. What is missing here? Thanks a lot in advance.
Subin

There are a few things need to be performed on basis side after copy .
1. Restore of Logical system.--> check with Baisis team wheather they have performed this action or not after copy.
2. Check your source system connection, in rs1-- source sytem --check
3. Change the aleremote or Bwremote passwords.
4. Try to logon to your sourcesystem ( from SM59 Tcode) Remote logon.
Hope this helps.
Regards,
Reddy
Edited by: Reddybl on Apr 1, 2010 11:56 AM

Data Load Error after Client copy on Source System

We did a client copy to our QAS source system. After that was complete, I tried to do a couple of full data loads. But they fail. The only errors I see are on the source system when I try to manual update the Idocs. They are:
EDI: Partner Profile not available
Entry in inbound table not found
Is there a step I need to take after the client copy and before the loads? I have a feeling that I'm forgeting something.
Thanks,
Chris

Hi Chris,
Check the following.
1> Go to WE20 check whether you are able to see two logical system in "Partner Type LS" one for Source and one for Myself.
2> If you say Yes for <1> then check in both the logical system, in the classification tab, partner status should be 'active'.
3> Check you have used REMOTE USER in main and in Outbound and inbound Parameters "Post Processing Permitted tab " for each Message type.
4> go to out bound message type and check the "Receiver port" pointing to correct RFC destination for both ( Source and Myself logical system).
If your answer is no for <1> then perform all the steps.
Hope this will help you.
Suneel

After Client copy - No Authroization Issue

Dear All,
Good Day,
We copied Production data to Quality system through Transport management System. We checked those data copied successfully. After client copy, login in Quality also done successfully
But unable to run any transaction. no authroization error occur for all the transaction for all the user id.
"You are not authorized to use transaction XXXX"
Kindly advice me to resolved this issue.
Best Regards,
KSK

Was security transported down? Can you log into the system as SAP*? If so, check to make sure that all the roles and user masters where copied. You can also run st01 to do an authorization check.

Client Copy and System Restore query

Dear All,
I have few major doubt regarding client copy and system restor.
1. In my Quality system there are 2 clients: 100 and 200.In my PRD there is only 1 client 300(other than the standard default clients). My doubt is during remote client copy with SAP_ALL profile from PRD to QUA why the space increases only in MB.
I have been asked the same question by my management. They are saying PRD is 300GB and QUA is 220GB then why the space increases in MB though all data is copied in client 200(QUA) from client300(PRD)
2. If I delete client why the space is released in MB. Because according to them it should be in GBs.
3. Now my third query is I have to restore PRD backup in QUA.So I said that this requires same <SID> and Same sapce in the sapdatafiles(OS is HP-UX 11.31 and DB is Oracle 10g).So I have to explain them why these two things are contradary to each other. In case of client copy space required is only in MB and in case of System restore of PRD in QUA sapce require is in GBs.
Your suggestions will be highly obliged.
Regards,
PG

1. In my Quality system there are 2 clients: 100 and 200.In my PRD there is only 1 client 300(other than the standard default clients). My doubt is during remote client copy with SAP_ALL profile from PRD to QUA why the space increases only in MB.
Response > Because during client copy your customizing and other objects are copied.
The database structures,tables etc are already present.
2. If I delete client why the space is released in MB. Because according to them it should be in GBs.
Response > Since client deletion is not same as deleting database /customizing tables .If you delete complete dataspaces/tables then there will be sizeable difference.Similar logic as Response 1
3. Now my third query is I have to restore PRD backup in QUA.So I said that this requires same <SID> and Same sapce in the sapdatafiles(OS is HP-UX 11.31 and DB is Oracle 10g).So I have to explain them why these two things are contradary to each other. In case of client copy space required is only in MB and in case of System restore of PRD in QUA sapce require is in GBs.
Response > Since in a system copy you will copy data files (which includes tables,and all otehr strucutres ) hence the size required will be similar to PRD.

TCURM in target client empty after Client Copy

Hi Experts,
Has anyone encountered situation whereby TCURM does not contain a record for the target client after Client Copy process is completed? Is this a feature or bug?
Regards

Hi , I user the exclude tables option to exclude some tables.
but I have another problem: the client copy still failed. I get these informations:
table/object   component                         error
ANLU           FI-AA-AA                   Field missing locally
C905            SD-MD-CM                Different Field Names
IMPTT          PM-EQM-SF-MPC      Field missing locally
how can i finish my client copy ?   can you give me the solution
thanks very much

How can I get Lr 5 to recognize my iPhone 4s as a device to copy and import photos?

How can I get Lr 5 to recognize my iPhone 4s as a device to copy and import photos?

It does not work! This occurred since I upgraded to the iOS7 software on my iPhone. Apple claims it's an Adobe problem
Sent from my iPhone

AFAB: Runtime Error after client copy.

Hi all,
I'm having a problem with the transaction code AFAB (post client copy). After client copy from PRD to DEV, I'm encountering this runtime error "SAPSQL_ARRAY_INSERT_DUPREC - The ABAP/4 Open SQL array insert results in duplicate database records." whenever I tried to perform AFAB. Test run was executed successfully but I cannot complete the actual background processing.
I have try with other asset (in the same client) and encounter the same problem. Likewise, I have successfully completed the depre. if I try the same and other asset (in a different client on the same server).
I've check the number range in FBN1 and have verified that the range is correct.
Any advice as to how I can solve this problem?
Thank you.
Regards.
p/s: if there is duplication, how do I find where the duplication is located and how do I remove this duplication?
p/s 2: the standard SQL that is having this problem is "INSERT COBK FROM TABLE COBK_INS."
Edited by: Sek Yao Ooi on Aug 5, 2010 5:21 AM

Solution obtain from snote-83731 ; thanks to SAP-Marketplace's support.
Issue solved.

I installed the latest version of iTunes (10.6.3.25) on a new Windows 7 PC. I can see ahred libraries on Shared but can't import as the line containing the Settings and Import buttons does not display. Any suggestions?

To move the iTunes library to this new computer I switched on Home Sharing and can see the other libraries on my home network. If I select tracks from a Shared library I can't import them as the strip containing "Show: All Items" and the "Settings" and "Import" buttons, does not display at the bottom of the screen. Goes straight from the list of tracks to the strip with Playlist icons and xxxx items, tttttt total time, yyyy GB.
Any suggestions for making the Import button appear?

I hvae the EXACT same issue
I built a new computer which is EXTREMELY fast overclocked i7 ect and.. ITUNES DOESNT WORK
I click on itunes which ive uninstalled and reinstalled and reset the winsock AND seen if there were any errors AAAAAAND ive check the Hkey to make sure bonjur was the only one in there which it is and all that happens is my cpu goes to 25% and i cant do anything except go into the task manager and close it! ANYTHING with itunes (everything else is premium speed).
what do i do
windows 7 64 bit

I've had my ipod shuffle (2nd generation) for a long time now and after a year and a bit of not being in use it doesn't work. When I connect it to the computer it doesn't come up. Can my ipod be charged or fixed?

I've had my ipod shuffle (2nd generation) for a long time now and after a year and a bit of not being in use it doesn't work. When I connect it to the computer it doesn't come up. Can my ipod be charged or fixed? Please help!

That is about normal. You can maximize battery life by changing some settings. See:
Apple - Batteries - iPod
Apple will exchange your iPod for a refurbished one for with a new battery for $79. They do not fix yours.
Apple - iPod Repair price
A third-party place like the following will replace your battery for less. Google for more.
iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
Replace the battery yourself if you are up to it. You can purchase a replacment for about $10
iPod Touch Repair – iFixit

After client copy and import export, WebUI not functioning

Similar Messages

Maybe you are looking for