After FLash, won't save CMOS settings, trys to boot from network

MS-6712 board, flashed BIOS, now 7/29/03 v1.9, with AMD XP 2500 Barton.
Win XP, plain old home computer on dialup.
I flashed BIOS, now it will not let me enter BIOS by pressing DEL key.
It boot to screen that says "Press to display network boot option
If you ignore, it says "Try network boot first, then local drives" and goes to a screen CMOS settings wrong. F1 to enter setup, F2 to load defaults"
If you SHift-Tab, it says press R for RPL, P for PXE, any key to load local drive.
No matter what you press, it comes to the CMOS Setting wrong screen.
I flashed BIOS, CTRL-HOME back to old BIOS - same message, so then and back to new one again, etc.  I did a FIXMBR and FIXBOOT in windows XP.  No luck. The problem is that even after setting up BIOS to boot from hard drive, etc, ad save changes and restart, it won't remember the settings.  The battery is also testing at proper volt.  I did just replace bad RAM after upgrading to AMD 2500, but it was fine before I flashed.  PLEASE HELP!!!!  By the way, I can understand technical instructions and PC terms (I think)

Quote
F1 to enter setup, F2 to load defaults
Whell, did you try F1?
This always happens after you flash/clear the CMOS...

Similar Messages

  • Getting an error when I try to boot from my snow leopard disk

    I want to install Snow Leopard on a partion on my new iMac. But when I try to boot from my old Snow Leopard-startup-disk all that happens is that I hear some beeping noise from the iMac.
    Would apreciate any help.
    Best Regards
    Andreas.

    If your machine shipped with Lion, most likely you cannot install SL, since it won't run on it. Details in Don't install a version of Mac OS X earlier than what came with your Mac

  • Watermark source file won't save in settings

    I have successfully created several watermark images that have source files (both in PDF format and JPG format). But there is one that I cannot get to save. I have tried the image in both JPG and PDF formats, but for whatever reason, when I try to save the settings, the source file is not saved and it just comes up as blank text when I select it for use. I have tried over and over again to save this watermark.
    As a result, whenever I want to apply this particular watermark, I have to go and browse for and find the file time and time again.
    ?? Any clue as to why this one won't save? Is there a maximum number of watermarks that can be saved?

    You can look at the place where the settings are saved.
    For Acrobat 8 and MS Vista the place is:
    X:\Users\{user}\AppData\Roaming\Adobe\Acrobat\8.0\Preferences\Watermark

  • Mail won't save MobileMe Settings

    After .mac changed to MobileMe, I changed the settings in OS X Mail so that it worked with servers using the "me.com" domain name rather than "mac.com." However, whenever I change settings, the changes to not seem to stay. Despite telling Mail to save the settings prior to closing the settings window, if I go back into settings, the "me.com" settings have been changed to "mac.com."
    Has anyone else noticed this? Is there a fix?

    Do a backup, using either Time Machine or a cloning program, to ensure files/data can be recovered. Two backups are better than one. 
    Try setting up another admin user account to see if the same problem continues. If Back-to-My Mac is selected in System Preferences, the Guest account will not work. The intent is to see if it is specific to one account or a system wide problem. This account can be deleted later.
    Isolating an issue by using another user account
    Try booting into the Safe Mode using your normal account.  Disconnect all peripherals except those needed for the test. Shut down the computer and then power it back up after waiting 10 seconds. Immediately after hearing the startup chime, hold down the shift key and continue to hold it until the gray Apple icon and a progress bar appear and again when you log in. The boot up is significantly slower than normal. This will reset some caches, forces a directory check, and disables all startup and login items, among other things. When you reboot normally, the initial reboot may be slower than normal. If the system operates normally, there may be 3rd party applications which are causing a problem. Try deleting/disabling the third party applications after a restart by using the application un-installer. For each disable/delete, you will need to restart if you don’t do them all at once.
    Safe Mode - Mavericks   also Yosemite
    Safe Mode - About

  • HT1677 What happens when you press "save" and the device won't save your settings?

    Today, I upgraded my ipod touch 4 gen to IOS 6.
    I just tried to save my settings under Safari, and I get an error message, "https://www.google.com Sorry, we failed to save your settings. Try again later."
    I tried most of the evening, and still the same error message...
    I've tried to "Google" the error message, there is NO match, lots of other stuff, but no match to my error message.
    Topbarhive

    Mor info on this issue, I can't disable the "Search History" (ie: check "Do not save searches") IF I try I get the error message...
    I seem to be able to disable the rest of the stuff, without the Search History checked "do not save searches" and save without the error.
    If I try to check only "do not save searches" it will give me the error.
    There must be something in IOS6 that I checked in someother place on my device that is causing my issue.
    BTW there is no option to "remove all website data" on my device, it just show a "grayed out" "0 bytes" beside the "term" Website Data.
    Thanks for helping me.

  • Why, when I startup my Macbook, does it try and boot from a disc even when there is nothing in the disc drive?

    This is a frustrating problem, will I need to format and reinstall the OS? The only temporary fix is if I hold the option key and tell it to boot from the hardrive.

    I hate to be a pain, but given the considerable oddity of your situation, I think it might be helpful for us to know the exact wording of the message.
    Start up from your most recent OS X installer DVD, open Disk Utility from the Utilities menu, select your internal hard drive in the left pane of DU, click the First Aid tab in the right pane, and run the Repair Disk routine. Then quit Disk Utility, quit the Installer, and try again to sart the computer up normally.

  • Flash Player won't save local settings

    We are waiting Adobe.  Fix this problem.  With Flash not working on both Macs and Windows systems it seems that Flash will soon be irrelevant.

    Hi fmlogue, What thread people post on doesn't necessarily reveal their system nor their problem. Regarding the fact that a bug report has been filed would not be the determining factor whether there is a bug in the Flash Player code. I'm sure you know that Java has  a system of reporting bugs and if and when THEY decide if it is valid then they assign an ID
    to the report. They then investigate and make the determination whether it is so or not. So just because someone reported a bug doesn't make it so. Like I said if there were a true bug, then it would affect everyone that installed Flash Player and that is simply not the case.
    Regarding the link you provided, http://bugs.adobe.com/jira/browser/FP-1914, I am not registered. However, I did take a look at JIRA, a maker of plug-ins. Also I took a look at Atlassian, an Australian based Software Company, that is into
    Software Development Tools and Collaboration Software & JIRA plugins.
    What this has to do with Flash Player, escapes me. I also took a look at Pandora Streaming Music and don't see where it is much different than other streaming music programs.
    Are you a developer? How is Adobe Air needed for streaming music? Just a question, since I don't use Adobe Air and am able to listen to almost anything on the Internet, TV and radio, etc.
    fmlogue, this is not MY program, please, if it was do you really think I would be on this forum? :-) I am a user like yourself,
    just trying to help people with their Flash Player problems, since I don't have any.
    Now, I am not familiar with MAC, although I was able to help a couple of users with their MAC and Flash Player issues. Not because I knew anything about MAC, but because they were good at sending screenshots and I was able to see what their problems were. PC's and MAC are so different and I'm not sure of the "language" so have some problem with that.
    You would probably be better served if you started a new thread with the information that you provided here and get advice from the MAC users. That is up to you. Like I said, I am just not that familiar.
    From your Macromed folder you have the latest FP; and in Library, the Shockwave 10 is most likely for Adobe Air.
    The only way you and I can work together on this if I speak PC to you and you interpret and speak PC to me.
    Regards,
    eidnolb

  • Camera Raw 6.7 won't save developer settings

    I'm running Adobe CS 5 with Camera Raw 6.7 on a Windows Vista machine.
    I have a Canon T3i that I shoot all of my Raw files from. Which Camera Raw 6.7 supports and have not had trouble in the past.
    Recently everytime I've loaded the Raw files into a new project folder and begin to adjust the first Raw file, none of the develper settings are saved or the updated Raw file won't show anything on Bridge (The little triangle on top of the Raw file won't show on Bridge). The XMP file contains the adjustments but bridge and camera raw will not load the adjustments. I am not able to copy or paste settings from other previous Raw files either.
    The weird part is that I am able to adjust Raw files and developer settings are properly saved in older folder created previously. This seems to happen everytime I start a new project and load the Raw files into it.
    I've tried clearing out the Camera Raw cache, and export cache for that folder but nothing help. I've even tried rebooting. Only after a good amount of time has passed and I've tried to keep on clearing the cache does Camera Raw finally functions properly and saves the developer settings afterwards. It's very random and very annoying. I usually end up wating alot of time trying to get it to work and at times can get very frustrating when the projects needs to be completed.
    Has anyone had similar issues with Camera Raw? Any solutions or work arounds? Or what's causing it, and how can I avoid it??
    Any help would be greatly appreciated and would help me not loose too much sleep.

    So after looking around in the forums I found the solution. Some other members had similar issues.
    The issue stems from not having the correct time set on the camera. Here's the link to the forum post with more detail:
    http://forums.adobe.com/message/4962247#4962247

  • ITunes 7 won't save my settings - Please Help!!!

    I just downloaded the latest version of iTunes, and every time I open it, it takes me to the 'iTunes Setup Assistant' and it deletes all of my settings whenever I close and re-open it. What's going on?!

    it's possible that this is being caused by damaged itunes preference files. perhaps try the techniques in this user tip to see if they work with that:
    b noir: iTunes won't let me change a preference

  • Quicktime 7.1.5 Won't Save Miscellaneous Settings

    Please help ...
    Just recently upgraded my Quicktime Pro to 7.1.5. Never noticed any streaming problems before, but now, I get the Quicktime ? (question mark) symbol on a few browsers (AOL, Netscape).
    I went into Quicktime>System Preferences>Advanced & first unchecked "Enable Flash," then I go into "MIME Settings" and check the "Miscellaneous (Miscellaneous file formats)" then click "OK." However ... went I either restart or quit of the application then open it up again, the Miscellaneous button is unchecked. Why is it not saving the changes??
    Many thanks in advance. Hope you can help.
    Thanks
    mbdrums

    To Apple Discussions!
    Try the following:
    Make sure you have the latest versions of Adobe Flash Player Software
    QuickTime Preferences > Advanced > MIME Stettings > Miscellaneous.
    Deactivate the "Flash Media" option.
    This tells the browser not to to display Flash Media and lets the newly installed Adobe software work its magic.

  • Flash won't save to a network mapped drive

    We upgraded a RAID5 disk array that we map from a network
    share recently. The original disk was 1.8TB the new one is a GPT
    disk that is 3.6TB.
    Now when we try to save files from FLASH CS3 we get errors
    concerning the file or disk is read only, make sure another program
    doesn't have the file open..etc..etc...
    All the permissions on the disk are fine. Photoshop CS3,
    Dreamweaver etc..all play fine with the large GPT disk. Anyone else
    have this problem or know of a solution.
    I know the first release of Encore had this problem even with
    TB drives. If it was over 1,000MB it did the same.
    thanks for any input.
    PS: I have let the adobe updated get all the appropriate
    updates for all products.

    Hi and welcome to Apple Discussions,
    Did you get the flash drive from a reliable source. There are some available on the net that show a large capacity but are only 512 mb. or 1 gb. drives that have been altered to display a much larger capacity.
    Good luck,
    Alan

  • Flash won't save or test run my files

    Hi, I guess this might have already been posted before, most
    things I post have....
    When I have copied my fla files over to my laptop so I can
    take work home with me, I can't then test movie, publish or save
    the files.
    How come? I just get this message:
    "Error creating Flash Movie File.
    Be sure the destination file is not reed-only or opened by
    another application. Also, check that the file name is not too
    long."
    None of the files are reed only and it only happens when I
    move them to my laptop.
    I really need to get this work done this weekend but can't if
    they don't run on my laptop.

    Not sure which OS you're using, but if you use Vista or Win7, the first time you launch DW, right-click and run as Administrator.  Set-up your site definition settings, extensions, browsers and other preferences from this elevated mode.
    Hope this helps,
    Nancy O.
    Alt-Web Design & Publishing
    Web | Graphics | Print | Media  Specialists
    http://alt-web.com/
    http://twitter.com/altweb
    http://alt-web.blogspot.com

  • T520 with dual monitors won't save resolution settings

    I have a new T520 docked with a 4338 docking station.  I've connected 2 Lenovo L1940p LCD's to the dock using the 2 DVI ports.  In order to set the 2 LCD's to 1440 x 900 (their max resolution), I have to disconnect the 2 DVI cables from the dock and boot the T520.  Once the T520 is up, I reconnect the 2 LCD's and they work fine.  If I leave them connected during the bootup, I am not able to set them to 1440 x 900.  The max it will go at that point is 1366 x 768.  Even if I boot the laptop before docking and then dock it after it's up, I lose my max resolution until I reboot without the LCD's connected.  I have the NVIDIA NVS 4200m and the driver is up to date (according to Windows).  I am running Win7 Enterprise.  I also tried changing to discrete graphics in the BIOS with no luck.
    Can anyone help with how to save this configuration so I don't have to go through this everyday?  Much Appreciated!!

    At this point I think you should get Applejack...
    http://www.versiontracker.com/dyn/moreinfo/macosx/19596
    After installing, boot holding down CMD+s, then when the prompt shows, type in...
    applejack AUTO
    Then let it do all 5 of it's things.
    Though it might just be that you need to use Disk Utility to Fix Permissions, but I'd do the Applejack thing with any messed install.

  • Urgent help need. DB is crashed. To save it I try to Upgrade from Oracle XE

    Hi.
    We have DB on Oracle XE 10.2.0.1. PC (Windows XP) was reboot and DB don’t start with C:\oraclexe\app\oracle\flash_recovery_area\XE\ONLINELOG\O1_MF_2_6YJ6WJX9_.LOG file. It is crashed with 0600 internal error. I have deleted this file and start DB with reset logs and “*._allow_resetlogs_corruption=TRUE” in initXE.ora. DB is crashed too. I have tested all DBF files by dbv – all files are valid.
    I have installed Oracle XE 11.2.0.2 and opened my DB in it with “startup upgrade”. DB is opened but I receive “ORA-04023: Object SYS.STANDARD could not be validated or authorized” and view ALL_OBJECTS is invalid. So I cannot export my data from DB (exp.exe also shows this error).
    I have read and try o lot of advice from Inet but I still have this error.
    I cannot export data by SQLDeveloper or Quest Toad for Oracle because view ALL_OBJECTS is invalid. But I can select data from my tables in SqlPlus.
    Our company will pay you for your help.
    Please help ASAP.
    My skype: thenoone18.
    Thanks.

    When you get ora 600 error you should contact oracle support. Also you should not use undocumented parameters.
    Looks like you have done so many things and only a valid consistent backup can save you.
    Edited by: manoj_kumar22 on Aug 4, 2012 5:59 AM

  • My iMac stayed with grey screen after power on. It repeatedly booting when I try to boot from the Mac OX install Disc.

    After I run bootcamp and try to install WinXP.
    I can't boot up from any system.

    Reboot and hold the option key down, choose OS X on your boot drive and set the System Preferences > Startup disk to OS X.
    You can't install XP on a Mac, Apple only supports Windnows 7
    Read the Bootcamp manual
    https://www.apple.com/support/bootcamp/
    https://discussions.apple.com/community/notebooks/macbook_pro?view=documents

Maybe you are looking for