After full restore from Time machine, my TM hard drive won;t mount

I got my macbook pro back from a logic board repair and restored it fully from Time Machine using my leopard install disc.
Took a while, but it has installed OK. But some applications weren't restored and now the Time Machine drive won't mount on the Macbook at all. When I open up time machine - and try to choose a backup disc nothing comes up.
The drive shows up on a PC when i connect it (but won;t read it as its mac formatted) so I'm pretty sure there;s nothing wrong with the drive.

Also, be aware that TM thinks you got a new Mac, not a new logic board. Thus you won't see your TM backups in the normal way. You'll need the (badly named) +*Browse Other Time Machine Disks+* option (see #E2 in the Time Machine - Troubleshooting *User Tip* at the top of this forum).
In addition, when you start doing new backups, TM will start a whole new "sequence," as if it were a different Mac. See #C8 in the Troubleshooting Tip for options.

Similar Messages

After restoring from Time Machine to new Hard drive, system will not boot

I replaced my hard drive on my Macbook (2008 model) with a larger drive. I then put in my Snow Leopard disk, and followed the steps to restore from Time Machine backup. a few hours later it said it was restored, but when trying to boot up, I just get a blue screen with an occasional flicker to the Leopard screen. I tried an earlier back up as well but with the same results. Any suggestions??

Same exact problem here just yesterday, folks.
Got a bigger hard drive on my MacBook Pro (15-inch Core 2 Duo) and installed it. Followed the restore procedures from Gizmodo (http://gizmodo.com/333319/the-secret-of-the-time-machine+assisted-hard-drive-swa p). Then got the blue screen immediately after the chimes.
I only managed to transfer my old disk content by using CarbonCopyCloner.
Having said that, your solution looks uselful, Portland Mac! :
Portland Mac wrote:
... But when I decided to try and just do a fresh install and work my way back through all my software, I started by installing Snow Leopard and suddenly it boots and everything from my Time Machine backup is there...
But I would not say the following:
Portland Mac wrote:
... On a new drive apparently you have to install Snow Leopard before you do a time machine restore.
Am I mistaken, or did you do a fresh install after restoring your TimeMachine backup?
In any case, I found an interesting Apple article that might confirm that there is a problem: [Mac OS X v10.6: Issues after restoring a Mac from a Time Machine backup made with a different Mac ("Restore System From Backup…")|http://support.apple.com/kb/TS3243]. Or is it a completely different thing?
And another discussion that might give some good advice: [http://discussions.apple.com/message.jspa?messageID=12578529#12578529]. Personally, I will now do as the man says: two backups, on two different external hard drives, using different apps, the other one being CarbonCopyCloner...
For info, and I don't know whether that matters, my backup disk had been full and some past content had been erased automatically by Time Machine. But I don't think this should have mattered...

Toasted my installation. Restoring from Time machine to 2 hard drives?

I just installed a second hard drive into my macbook pro. SSD is the system drive and HDD is the data drive.
When it was still working, I had my home folder on the SSD and my iTunes and Photo libraries on the HDD. Things were good.
Then I decided to move the entire home folder to the HDD.
Sys Prefs -> Users -> right-click the user -> advanced -> "move the home folder"
and again, everything was good.
Then I read something about having the user Library folder on the SSD is a good thing.
So I moved the home folder back to the SSD. Rebooted and all my prefs were now gone. Figured I messed up something and didn't want to troubleshoot.
So time for a restore.
Attempt 1
- Open Time Machine, select both hard drives, selected a past date and hit restore.
- Got a message that I didn't have enough space.
* I figure this is because time machine restores the entire contents of each drive as entire new volumes as a first step.
Attempt 2
- Go into recovery mode COMMAND+R
- Discovered I don't have a recovery partition
* I guess this is because I cloned my original system drive to the SSD using CCC and it didn't move this part.
Attempt 3
- I created a LION USB Install Key
- Booted from it, and selected 'Reinstall Lion' (because I read an article that I could recover my files after Lion had finished installing)
* Discovered that it reinstalled 10.7.0 and I would have to apply all patches on top. It didn't restore my HDD either.
* Later found out this method only restores the main system drive.
Attempt 4
- Now that I have a recovery partition, I booted from it.
- I selected "Restore from Time Machine Backup"
- Was able to select my Time Capsule, and it gave me choices on which date I would like to restore to.
- I selected and hit restore.
* It's about 25% done now. And I realize that i should've done this in the first place.
Question: Will this method restore both of my hard drives?

hsmp wrote:
Question: Will this method restore both of my hard drives?
No, only a single OSX drive. If both were backed-up, and both contained OSX, there was a (not very obvious) option to select which one you wanted.
See Time Machine - Frequently Asked Question #14. Section (g) shows this.
If you want to restore the "other" drive, and it contains OSX, run the restore again and select it.
If the other drive doesn't contain OSX, use the "Star Wars" display to restore it, per FAQ #15.

After Full Restore from Time Machine..

Hello All!
I've searched around but can't find the solution.. Unfortunately there was a terrible accident with my last Macbook Pro so I purchased a new one... I did a full install using Migration Assistant to replace my User account from Time Machine. I never got the option to 'use time machine history' and now aren't sure whether it's 'building' on top of my old Time Machine or just starting a new one. When I go into preferences it says 'oldest Back Up - None' & 'Latest Back Up - None'
Does any of this matter as the Old back ups are still there - the External Harddrive says 127 of 250Gb used... Or do I need to 'merge' these backups?
Many thanks.

I think that you should be fine. If you open Time Machine you should be able to determine the status and it should work as designed.
I have never encountered the"Inherit Backup History" that you mention. It probably is a Lion feature (I still use Snow Leopard) and I have never used Time Machine to transfer data to a new MBP or a restore. I prefer to select what I want to retain and let the rest go by the wayside. This way any 'trash' I may have does not get copied to the new MBP. Consequently when I connect the Time Machine HHD, it then does an entirely complete new update.
Keep the Pondini web site in mind. It has a plethora of useful Time Machine information.
Ciao.

After full restore from Time Machine Backup, will TM continue

I fully restored my iMac using my time machine backup. Since my iMac looks the exact same as before why won't time machine just continue backing up like normal? Why do I have to start all over again with a full backup and then the incremental backups?

Endeesea wrote:
Just checked out the linked article, and it looks very helpful. I'm at work at the moment, but when I get home I will take a look. Thanks.
That article wouldn't apply if the mac is exactly the same.
I think it would probably be easier just to wipe the backup drive and start over, if everything really is exactly the same.
Good luck!

How do I get past a blue screen after full restore from time machine and rebooting?

Wife had her hard drive replaced by apple, they reinstalled the os. After boot up system questions, the option to restore everything from timemachine backup was selected. System came up to login but would not take what the password should have been. I rebooted the macine and it has not come back.

That;s really not enough free space... you can use a tools such as OmniDiskSweeper to find out where your large files reside and begin pruning (or copying to an external if they're files that you want to keep).
One thing is certain - if you're going to continue your current usage you're certainly going to need to install a larger boot drive.
Clinton

Restore from time machine on clean hard drive

I want to change my current hard drive to a SSD hard drive. Unfortunately i lost the DVD that came with the Mac, so my question is whether i can do a complete restore from the time machine backup? Does it include all the iOs file and everything?

You will need the Install DVD that shipped with your Mac...
Contact AppleCare and for a small Handling fee they will send you the Appropriate disc.
Contacting Apple World Wide for Support and Service
http://support.apple.com/kb/HE57
Apple Contact USA
http://www.apple.com/contact/

Leopard. Did a full restore from Time Machine. Now I can't access my other internal and external drives. I get the following error: The folder "Capture Video" can't be opened because you don't have permission to see its contents.

Leopard. Did a full restore from Time Machine. Now I can't access my other internal and external drives. I get the following error: The folder “Capture Video” can’t be opened because you don’t have permission to see its contents. I have repaired permissions pn the main harddrive. When I try too click on a disk I get the previously stated error. I can't even open up information to see what permission/access there is. It simply will not let me see the content. It shows the content of my main hard drive when I have clicked the other harddrive's name.

Solved:
sudo chflags 0 /Volumes/"FCP Time Machine BU"
sudo chown 0:80 /Volumes/"FCP Time Machine BU"
sudo chmod 775 /Volumes/"FCP Time Machine BU"
sudo chmod -N /Volumes/"FCP Time Machine BU"

Full restore from Time Machine fails

I am trying to replace a failing hard drive. The failing drive in in a box. A new one is in the computer.
When I try to run a full restore from Time Machine it comes up with an error saying the restore failed. No useful information like codes or reasons are given.
I'd prefer to do a full restore, but I fear the cause is too much system file corruption on the TM drive. I think the only alternative is to recreate the four user accounts and somehow copy the files back to the accounts.
Before I swapped the drives I set all permissions on the files in each account to admin=read/write, user=read/write, other=read only. I then created a couple incremental backups to Time Machine.
Currently I have 10.5.0 installed. I have to install 10.4, then upgrade, which is a very lengthy process.
The old drive is still (barely) functional. While using it though, if I try to run any program, the system hangs for minutes at a time, (BBOD).
How should I proceed? Is there a way of repairing the backup? Do I try the copying all the files? I have no way of using the Migration feature since I only have the one Mac. I do have a PC.
Thank you in advance.

Melnibonean wrote:
When I try to run a full restore from Time Machine it comes up with an error saying the restore failed. No useful information like codes or reasons are given.
It's possible that as the HD was failing, it corrupted something in your installation of OSX, and that was backed-up, so when you restore it, you're restoring damaged items.
Try again, but pick an earlier backup, from before the problems started.
When you do, once it starts, select Window, then +Show Log+ and +Show All logs+ from the menubar. Watch the messages; if it fails again, note what it says. That will tell us, roughly, where it was, so we may be able to avoid it.
Currently I have 10.5.0 installed. I have to install 10.4, then upgrade, which is a very lengthy process.
Huh? Why would you install Tiger?
How should I proceed? Is there a way of repairing the backup?
Possibly, depending on what's wrong.
Instead of selecting +Restore System from Backup+ from the Utilities menu, select +Disk Utility+ and use it to do a +*Repair Disk+* on the backups (via your Leopard Install disc). Then quit DU and try +Restore System from Backups.+
I have no way of using the Migration feature since I only have the one Mac.
Yes, you do, if the backups are ok. You can use +Setup Assistant+ or +Migration Assistant+ from your backups (or a clone), not just another Mac. But they both only use the most recent backup, which may be damaged, so try the full restore first.

Full restore from Time Machine fails what now!

Just upgraded to 10.8 and all was fine except on crucial pice of software that was supposed to work in 10.8 but didn't.
I tried to revert back to 10.6 via full restore but it failed. Now I just tried to restore from TM backup of the 10.8 restore point.
It fails too. All my HDs check out fine. What went wrong and how can I get back to working?

Melnibonean wrote:
When I try to run a full restore from Time Machine it comes up with an error saying the restore failed. No useful information like codes or reasons are given.
It's possible that as the HD was failing, it corrupted something in your installation of OSX, and that was backed-up, so when you restore it, you're restoring damaged items.
Try again, but pick an earlier backup, from before the problems started.
When you do, once it starts, select Window, then +Show Log+ and +Show All logs+ from the menubar. Watch the messages; if it fails again, note what it says. That will tell us, roughly, where it was, so we may be able to avoid it.
Currently I have 10.5.0 installed. I have to install 10.4, then upgrade, which is a very lengthy process.
Huh? Why would you install Tiger?
How should I proceed? Is there a way of repairing the backup?
Possibly, depending on what's wrong.
Instead of selecting +Restore System from Backup+ from the Utilities menu, select +Disk Utility+ and use it to do a +*Repair Disk+* on the backups (via your Leopard Install disc). Then quit DU and try +Restore System from Backups.+
I have no way of using the Migration feature since I only have the one Mac.
Yes, you do, if the backups are ok. You can use +Setup Assistant+ or +Migration Assistant+ from your backups (or a clone), not just another Mac. But they both only use the most recent backup, which may be damaged, so try the full restore first.

Full restore from Time Machine has not restored my photos

I was getting a triangle with an exclamation mark in it when I tried to click on my photos in iPhoto (photos uploaded from my camera only - iPhone pics are still there). A backup from Time Machine didn't work, so I did a full restore from Time Machine to a date when I knew all was well with my photos but I still get the triangle/!. Where are my photos?

The ! means that iPhoto has lost the link to the original file.
Are you running a Managed or a Referenced Library?
A Managed Library, is the default setting, and iPhoto copies files into the iPhoto Library when Importing. The files are then stored in the Library package
A Referenced Library is when iPhoto is NOT copying the files into the iPhoto Library when importing because you made a change at iPhoto -> Preferences -> Advanced. (You unchecked the option to copy files into the Library on import) The files are then stored where ever you put them and not in the Library package. In this scenario you are responsible for the File Management.

Restore using Time Machine to new hard drive, but last "full" backup was 2012. how do I restore the rest of the Time Machine backups, particularily IPHOTO libraries for each user?

Restore using Time Machine to new hard drive, but last "full" backup was in 2012. How do I restore the rest of the Time Machine backups, particularily IPHOTO libraries for each user?
I entered Iphoto for my user and only photo up until 2012 were in the library. I thought the restore would do the incremental Time Machine backups too.....
Running 10.8.2

It usually means you are running Mavericks but have an earlier version of iPhoto. Open the App Store and upgrade your version of iPhoto to the Mavericks version.
The iWork apps are free with a new iOS device since 1 SEP 2013. They are free with a new Mac since 1 OCT 2013. They are also free with the upgrade to OS X Mavericks 10.9 if you had the previous version installed when you upgraded.The iWork apps are free with a new iOS device since 1 SEP 2013. They are free with a new Mac since 1 OCT 2013. They are also free with the upgrade to OS X Mavericks 10.9 if you had the previous version installed when you upgraded.
iWork and iLife for Mac come free with every new Mac purchase. Existing users running Mavericks can update their apps for free from the Mac App Store℠. iWork and iLife for iOS are available for free from the App Store℠ for any new device running iOS 7, and are also available as free updates for existing users. GarageBand for Mac and iOS are free for all OS X Mavericks and iOS 7 users. Additional GarageBand instruments and sounds are available for a one-time in-app purchase of $4.99 for each platform.

How to restore from Time Machine onto an external drive

Hi all,
I am a backup freak, and I don't feel entirely safe with Time Machine taking care of backing up my system unless I can test every now and then that I would be able to do a full restore. I've had problems in the past with .Mac/MobileMe's Backup.app, which would not be able to restore from an otherwise apparently successful backup, for one reason or another.
So, is there a way to test a full restore from Time Machine onto an external hard drive?
Thanks for your advice

Allamistakeo wrote:
Hi all,
I am a backup freak, and I don't feel entirely safe with Time Machine taking care of backing up my system unless I can test every now and then that I would be able to do a full restore. I've had problems in the past with .Mac/MobileMe's Backup.app, which would not be able to restore from an otherwise apparently successful backup, for one reason or another.
So, is there a way to test a full restore from Time Machine onto an external hard drive?
of course. connect an external, boot from the snow leopard DVD and choose "restore system from backup" from the utilities menu. follow the instructions and choose the external drive as the restore destination. make sure it's properly formatted. it should be formatted mac os extended with GUID partition scheme.
also, you might want to consider doing secondary backups in addition to TM by making a bootable clone on another external drive. use CCCloner or Superduper for such backups.
Thanks for your advice

Trying to restore from time capsule to nes hard drive, keeps looking for disks ! Can you help

ccan't restore from time capsule to new hard drive, after changing to new HD, after calculating required space to restore it keeps looking for disks! Have have put original OS X install disk 1 in it won't Eject , any help

The very best way to do this is with ethernet to the existing router. Put the TC in bridge mode manually.
Then plug it in to existing router.. we recommend LAN router to WAN on the TC but even that is not 100% necessary.
If you want to link by wireless, to a non-apple router that is bad.. recommend strongly against it. Join a wireless network is super slow.
If you have a desktop Mac you can plug it directly into the Mac by ethernet.
But we need to know how the Mac is connected to internet.
I have given some info on one layout here.
https://discussions.apple.com/thread/4817218?tstart=30
If you end up relying on an old TC. And any of the models from Gen1-3.. and increasingly Gen4 have all reached EOL.. they can die suddenly and either take your files with them or be hard to recover. Also a TC is slow cf a USB external drive even, which is more reliable. Considering a 2TB is <$100 I would be careful using an old TC simply because you got it free.

After a full restore from Time Machine, I get "error code -6584" when trying to go into TM.

I took our iMac in, at the direction of Apple, to have the hard drive replaced. When we got it back, I restored from Time Machine (on Time Capsule). One file on the desktop, a spreadsheet file, has reverted to a version five months old, with the loss of considerable data, so I don't know which files I can now trust. Also, when I try to go into Time Machine, I get "error code -6584" and am unable to access my backups
This is potentially very very bad. What can I do?

Solved:
sudo chflags 0 /Volumes/"FCP Time Machine BU"
sudo chown 0:80 /Volumes/"FCP Time Machine BU"
sudo chmod 775 /Volumes/"FCP Time Machine BU"
sudo chmod -N /Volumes/"FCP Time Machine BU"

After full restore from Time machine, my TM hard drive won;t mount

Similar Messages

Maybe you are looking for