After Install. Templates in App Builder not correct.

After upgrading from 1.5 to 1.6 Images were not showing after logging into INTERNAL/ADMIN.
I fixed that by copying the images directorio into CCD_HOME/marvel/images and setting the /i/ in marvel.conf.
Now images are OK but the page is still not using the correct template since fonts are too big, buttons are not showing correctly, and page is not formatted correctly.
I am comparing to another installation which I did the same installation about a month ago.
Can anyone help with anything I can try.
Thanks

Apparently flows.css is not being found.
I tried removing this file on the working system and I got exactly the same problem.
The file is present in ...marvel/images/css/flows.css so it looks like it is not being found.
The images are found but the css is not.
My marvel.conf references /i/ correctly. Does the css use this reference or one configured elsewhere?
Can anyone help?

Similar Messages

TS4436 Iphone 4 camera worked fine for 2 years then turned all flash photos red after installed Fast Torchlight App - deletion of app did not fix camera problem - please help?

Iphone 4 camera worked fine for 2 years then all photos with flash came out as red after installed Fast Torchlight App - deletion of app did not fix camera problem - please help?

Try This...
Close All Open Apps... Sign Out of your Account... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430
If no joy...
Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414

After installing it, my macbook would not restart. All i would see is the Apple and the twirling circle. To get back to be able to use internet i had to put Snow Leopard disc holding "C" key.

I did a software update check. It showed to update to 10.6.8v1.1. After installing it, my MacBook would not restart.
I have tried this more than once. After the install all that happens is i get the Apple emblem and the twirling circle. I have let that go for literaly a couple hours with no results.
To get to be able to use my Macbook i have had to install Snow Leopard by holding the C" key and re-installing Snow Leopard.
Any help would be appreciated. i Have purchased "Lion" and cant access App Store to install until this update is done.
Very frustrating.
thanks in advance.

That's why you can't access the App Store. Minimum requirement is v10.6.6
Install this combo update > Mac OS X 10.6.8 Update Combo
Then restart your Mac, open the App Store.
You can download Lion by clicking Redeem under Quick Links right side of the App Store window then entering the redemption code.
You have checked to make sure your Mac can run v10.7 Lion? >>>> OS X Lion - Technical Specifications

After installing Lion all Adobe products not working will and to slow

After installing Lion all Adobe products not working will and to slow
Like the photoshop is to slow to work on it
Please I need to now what's the problem and how can I solve it
Best regards

Yeah Im at a loss too for what is going On here I Do Audio video Editing On the PC side till Now Just got a Not even 6 mo old Mac book pro Dual core 2.5 Ghz 17 in 160 Gb HD 2 GB Ramm did fresh reinstalled of tiger Patched to 10.4.11 then asked the tech at apple store best way to go for Installing my Adobe CS3.3 Master Suite for windows on Here As I said I did not want to go with Lepord as well as I do not use vista yet on PC side with my audio video Apps Abelton live 7.0 Reason 4 Pro tools 7.4 M powered Avid media Composer 3.0 and everything Adobe Makes now he says 2 ways to go VM fusion Or Parallels He likes the Parallels I go that route I install it realize to make Adobe suite work I have too do a custom Virtual machine with 1.5 GB ramm instead of default 512 MB and I create virtual HD at 60 GB instead of default 32 GB which The first time i Installed the master Collection at the 32 GB setting I think it ran out of disk space on the install so i increased the VM to the current settings went to Adobe to Parallels site and Got updates and windows and apple removal tools and ran them here goes reinstall # 3 it takes about 1 1/2 Hrs then at end give ya the error 19-20 errors and when you go look into the folders in Program files adobe there are no Icon launch files and in your programs tab under adobe suite all you see is 2 icons that do not launch anything ? any help is greatly appreciated new to Macs Like them but a lil discouraged !!!!

I purchased iPhoto after installing Yosemite, but App store shows the download is "waiting"

I purchased iPhoto after installing Yosemite, but App store shows the download is "waiting", with a greyed out box that says pause.

Hi exyankee,
Thanks for the question. If I understand correctly, an app is stuck on waiting. I would recommend that you read this article, it may be able to help you isolate or resolve the issue.
iTunes: How to resume interrupted iTunes Store downloads - Apple Support
Thanks for using Apple Support Communities.
Have a great day,
Mario

How do i reinstall mountain Lion after installing maverick. Maverick is not compatible with FileMaker 13 server. Maverick is now objecting to reinstalling Mountain Lion. Where do I go from here? Help?

How do i reinstall mountain Lion after installing maverick. Maverick is not compatible with FileMaker 13 server. Maverick is now objecting to reinstalling Mountain Lion. Where do I go from here? Help?

If you can download the ML installer you can make a bootable install media by using:
http://liondiskmaker.com/
If your Mini came with ML you can also boot to Internet Recovery
OS X: About OS X Recovery
and it will install ML. Make sure you boot to Internet Recovery and not the Recovery Partition. If to the partition you will only get Mavericks.

After installing iOS6, my Maps are not working at all, anything i search it says "result not found" even after placing a pin and selecting "Direction to here" i get the same result not found. Very disappointed with the new iOS

After installing iOS6, my Maps are not working at all, anything i search it says "result not found" even after placing a pin and selecting "Direction to here" i get the same result not found. Very disappointed with the new iOS.

Have you run it in a debugger? That will show you exactly what is happening and why.

Ipad mini working sluggish after installing ios7 why apple is not fixing this issue

Ipad mini working sluggish after installing ios7 why apple is not fixing this issue
Now it doesn't feels like i m using an apple device .
idevices should be flawless thats what it was

(A) Reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.
(B) Reset all settings
Settings>General>Reset>Reset all settings
Note: Data will not be affected but settings will be reset.

After installing Mountain Lion, contacts will not sync

After installing Mountain Lion, contacts will not sync to iphone 3G

I have the same problem... but when i connect my MacBook Pro late 2009 on my cousin internet the facebook page works normaly. but when i reconnect in my wifi it stops to work again... and it only hapens with macbook pro, On my iPad, iPhone and PC the facebook page works properly. And another thing, when my counsins bring their Macbooks to my network, it stops to enter on facebook too... I already reset my router config everything and facebook dont work with anything with mountain lion... My router is a linksys wag200n and the problem started when i install mountain lion. Thanks for help and sorry for bad english xD.

After installing Leopard, the app store icon disappeared

Hi,
After installing Leopard, the app store icon disappeared; how do I access it to download Lion? There is no trace of any App store in the Finder.
Thank you

You need to update to 10.6.6 (at least) to have the App Store.

HT2178 No sound from Doom3 after installed from the App store onto my intel iMac

No sound from Doom3 after installed from the App store onto my intel iMac 10.7.3 Any solutions?

Just just launch the Mac App Store, select the "Purchased" tab and download MainStage or any other application you already bought.

HT4623 after installing ios7 my Iphone4 will not work

after installing ios7 my Iphone4 will not work

Try a reset: hold down the home button along with the power button until you see the Apple, then let go.

TS1702 What to do when you get "iTunes library app not installed on iPhone; app could not be found"

What to do when you get "iTunes library app not installed on iPhone; app could not be found". None of the Apple suggestions fix the problem. For example, with Animoto, one of the problem apps, I have removed it, reinstalled it, and still get the eoor message.

Of course.
First of all, this started when an external drive i was using died on me. I have no doubt that these apps indeed are off my system. I figure between the apps I've bought for myself and my kid, I have about 150 apps.
Now. The issue.
When I sync my iPad with iTunes on my desktop, it goes through normally until it gets to the apps. When that happens, it get an error box that reads "Some of the apps in your iTunes library were not installed on the iPad because one or more errors occurred. For a list of appps that could not be installed, click on the triangle below."
Then I get a list of apps.
(Added note to any iTunes developers out there: The titles of the apps in this list do not always match the titles of the apps in the App Store. For example, one was called "MuseumGame" on my iPad. It's called "Museum of Thieves" on the App Store. I started out with a list of 60 apps. It was a major pain to track them all down. It would be nice to have everything the same so I can use the App Store search more effectively.)
Anyway, moving on....
The error message stops my sync until I dismiss it. That, honestly, is what makes this whole thing annoying enough to seek out an answer. I can't let my iPad start syncing and walk out of the room. Yeah. I know. First World problems.
Once I dismiss the error, the sync continues and all is well.
I did the following to try to fix the problem. Mostly, I did a lot of searches:
My list of purchased apps on my iPad both using the search box and by going to every page
Searched the main App Store on my iPad using the search field. When that didn't work, I used wider searches and just scanned the page(s) for the little cloud icon that showed I had purchased the app.
I got on my desktop iTunes and searched the apps from there (without a lot of hope, but trying to be complete)
At that point, I came to the conclusion that a small number of the apps are no longer available on the App Store.
Fine. I didn't want them anyway.
I got into iTunes and went to the Apps page. None of the errant apps showed up there. I searched the iTunes help files. Nothing. I crossed my fingers, said a little prayer to the search engine gods, and tried Google. I found some things that sort of matched but they basically boiled down to "re-download the app from the App Store" or "Restore your iPad".
So I spent a couple of hours restoring my iPad. I got the error message again. I hit Google again and came up with this thread. It was as close to my problem as I found.
I think that brings us up to date.
My fundamental problem is that I seem to have found a scenario where if you have to restore apps (because, perhaps, your external drive died) and some of the apps are no longer available for download, there is an error generated that can not be permanently dismissed.
Did I miss anything important?

After installing lion, time machine does not always back up. The back up disk is occasionally not recognized.

after installing lion, time machine does not always back up. The back up disk is occasionally not recognized. Help!

This is easy one.. for most.. just restart the TC.. ie pull out the power.. count to 10.. plug in the power.
If the simple doesn't work you can see more info here.
C12 http://pondini.org/TM/Troubleshooting.html

11g R2 -silent install: "Template General_Purpose.dbc does not exist"

I'm working in an environment where no X-Windows/GUI is permitted; therefore, I'm attempting to perform a -silent install of 11g R2 on RHEL 5.3 and am finding the screen output to my terminal window less than helpful. Fortunately, a thorough review of the install actions log provides what appears to be my problem.
The screen output I receive is as follows (I've added some line breaks to make it more readable):
(oracle@blade2-1 database)$ cd /opt/oracleStagingArea/Oracle11gR2/11.2.0.1.0/Disk1/database
(oracle@blade2-1 database)$ ./runInstaller -silent -responseFile /home/oracle/ResponseFiles/11gR2/ORCL11GD_enterprise_11201.rsp
Starting Oracle Universal Installer...
Checking Temp space: must be greater than 80 MB. Actual 91127 MB Passed
Checking swap space: must be greater than 150 MB. Actual 8000 MB Passed
Preparing to launch Oracle Universal Installer from /tmp/OraInstall2009-09-14_01-25-28PM. Please wait ...
(oracle@blade2-1 database)$
You can find the log of this install session at:
/u01/app/oracle/oraInventory/logs/installActions2009-09-14_01-25-28PM.log
That's it - no indication as to whether the installation was successful or failed or whether the NETCA/DBCA/etc. were successful or not.
I found that a listener existed after the install:
(oracle@blade2-1 database)$ ps -ef | grep tns
oracle 22597 1 0 13:29 ? 00:00:00 /u01/app/oracle/product/11.2.0/db_1/bin/tnslsnr LISTENER -inherit
My instance didn't appear to be up, though:
(oracle@blade2-1 database)$ ps -ef | grep ORCL11GD
oracle 22776 19142 0 13:39 pts/0 00:00:00 grep ORCL11GD
So, I checked the /u01/app/oracle/oraInventory/logs/installActions2009-09-14_01-25-28PM.log to see what it revealed. It shows me the following for the DBCA:
INFO: Started Plugin named: Oracle Database Configuration Assistant
INFO: Found associated job
INFO: Starting 'Oracle Database Configuration Assistant'
INFO: Starting 'Oracle Database Configuration Assistant'
INFO: Executing DBCA
INFO: Command /u01/app/oracle/product/11.2.0/db_1/bin/dbca -silent -createDatabase -templateName General_Purpose.dbc -sid ORCL11GD -gdbName orcl11gd.blade2-1.mycompany.com -emConfiguration LOCAL -storageType FS -datafileDestination /u02/oradata -datafileJarLocation /u01/app/oracle/product/11.2.0/db_1/assistants/dbca/templates -responseFile /home/oracle/ResponseFiles/11gR2/ORCL11GD_enterprise_11201.rsp -characterset WE8ISO8859P15 -obfuscatedPasswords false -sampleSchema false -oratabLocation /u01/app/oracle/product/11.2.0/db_1/install/oratab -automaticMemoryManagement true -totalMemory 2048 -maskPasswords false -oui_internal
INFO: ... GenericInternalPlugIn.handleProcess() entered.
INFO: ... GenericInternalPlugIn: getting configAssistantParmas.
INFO: ... GenericInternalPlugIn: checking secretArguments.
INFO: ... GenericInternalPlugIn: starting read loop.
INFO: Read: SYS_PASSWORD_PROMPT
INFO: Processing: SYS_PASSWORD_PROMPT for argument tag -sysPassword
INFO: Read: SYSTEM_PASSWORD_PROMPT
INFO: Processing: SYSTEM_PASSWORD_PROMPT for argument tag -systemPassword
INFO: Read: DBSNMP_PASSWORD_PROMPT
INFO: Processing: DBSNMP_PASSWORD_PROMPT for argument tag -dbsnmpPassword
INFO: Read: SYSMAN_PASSWORD_PROMPT
INFO: Processing: SYSMAN_PASSWORD_PROMPT for argument tag -sysmanPassword
INFO: End of argument passing to stdin
INFO: Read: Template General_Purpose.dbc does not exist. Please specify an existing template for database creation.
INFO: Completed Plugin named: Oracle Database Configuration Assistant
INFO: Oracle Database Configuration Assistant failed.
INFO: Oracle Database Configuration Assistant failed.
I don't see a template named "General_Purpose.dbc" in the $ORACLE_HOME/dbca/templates directory:
(oracle@blade2-1 database)$ cd /u01/app/oracle/product/11.2.0/db_1/assistants/dbca/templates
(oracle@blade2-1 database)$ ls -lrt
total 23216
-rw-r--r-- 1 oracle oinstall 11492 Feb 25 2009 New_Database.dbt
-rwxr-xr-x 1 oracle oinstall 1179648 Aug 14 03:01 example.dmp
-rwxr-xr-x 1 oracle oinstall 22536192 Aug 14 03:01 example01.dfb
Any suggestions would be welcomed!

Hans: None at all, unfortunately.
Srini: I obtained a copy of the note and read through it. It does look as though I should be able to run the DBCA in -silent mode to create a template, so no GUI needed. Thanks again!
On a side note: Did anybody else notice the "General_Purpose.dbc" template missing from the $ORACLE_HOME/dbca/templates directory after an 11g R2 software install on RHEL 5.3? I'm beginning to suspect that not all components were installed as expected during the software installation. the oraInstall<Date/Time>.err file is full of errors such as the following:
java.io.FileNotFoundException: /opt/oracleStagingArea/Oracle11gR2/11.2.0.1.0/Disk1/database/stage/Components/oracle.rdbms.install.seeddb/11.2.0.1.0/1/DataFiles/filegroup2.jar (No such file or directory)
All of these errors are complaining about only the following 4 compoments:
- oracle.ctx
- oracle.sysman.console.db
- oracle.owb.rsf
- oracle.rdbms.install.seeddb
Upon investigation, I found that there is no oracle.ctx, oracle.sysman.console.db, oracle.owb.rsf, or oracle.rdbms.install.seeddb under /opt/oracleStagingArea/Oracle11gR2/11.2.0.1.0/Disk1/database/stage/Compoments. Instead, the grouping is located under /opt/oracleStagingArea/Oracle11gR2/11.2.0.1.0/Disk2/database/stage/Components.
It seems that I may have staged the media incorrectly in two separate directories. Should I have unzipped both files into the same directory instead of separating them out?

After Install. Templates in App Builder not correct.

Similar Messages

Maybe you are looking for