After installing Mountain Lion, there's a ghost in the machine.

Pages open and close by themselves, the cursor jumps around the open page.

There are several possible causes for this issue. Take each of the following steps until it's resolved.
1. Follow the instructions in this support article.
2. Open the Bluetooth preference pane in System Preferences and check for unknown or forgotten input devices. Disconnect any USB input devices that you aren't using.
3. Boot in safe mode and test, preferably without launching any third-party applications. If you don't have the problem in safe mode, but it comes back when you reboot as usual, stop here and post your results. If you can't boot in safe mode, do the same. If you booted in safe mode and there was no change, go on to the next step.
4. Reset the System Management Controller.
5. If you're using a Bluetooth trackpad, investigate potential sources of interference, including USB 3 devices.
6. A swollen battery in a MacBook Pro or Air can impinge on the trackpad from below and cause erratic behavior. If you have trouble clicking the trackpad, this is likely the reason. The battery must be replaced without delay.
7. There's a report that a (possibly defective) Thunderbolt Ethernet adapter can cause the built-in trackpad of a MacBook to  behave erratically. If you're using such an adapter, disconnect it and test.
8. There's also a report of erratic cursor movements caused by an external display that was connected but not turned on.
9. If none of the above applies, or if you have another reason to think that your computer is being remotely controlled, remove it from the network by turning off Wi-Fi (or your Wi-Fi access point), disconnecting from a Bluetooth network link, and unplugging the Ethernet cable or USB modem, whichever is applicable. If the cursor movements stop at once, you should suspect an intrusion.
10. Make a "Genius" appointment at an Apple Store to have the machine and/or external trackpad tested.

Similar Messages

  • Final Cut Pro X after installing Mountain Lion I have lost some of the "additional content" which was available by clicking on "Download Additional Content" in the roll down from "Final cut Pro". Now this feature takes you to store update?

    Final Cut Pro X after installing Mountain Lion I have lost some of the "additional content" which was available by clicking on "Download Additional Content" in the roll down from "Final cut Pro". Now this feature takes you to Apple store update? which produces nothing! How can I download these free sound and music files, what has happened? Please help as there is nothing on the apple site to cover this??

    Final Cut Pro X after installing Mountain Lion I have lost some of the "additional content" which was available by clicking on "Download Additional Content" in the roll down from "Final cut Pro". Now this feature takes you to Apple store update? which produces nothing! How can I download these free sound and music files, what has happened? Please help as there is nothing on the apple site to cover this??

  • After installing Mountain Lion, Expose no longer works.

    After installing Mountain Lion, Expose no longer works.

    Unfortunately the Expose feature as you know it from Snow Leopard was removed by Apple in Lion and Mountain Lion.
    You can make all windows for an app 'expose' by putting the cursor on the Dock icon and using a 4-finger swipe-down.

  • Why does Google chrome not open or crash after installing mountain lion?

    Why does Google chrome not open and/or crash after installing mountain lion?

    Thanks.
    I have the updated chrome (9.0.597.19).
    I have just now tried the recommendation by Zohaib Sharif in teh google gropus link you sent
    http://funbird.co.uk/tech-articals/google-chrome-freezing-and-hanging-problems/
    Hope this works!

  • Lost mousescreen zoom after installing Mountain Lion

    After installing Mountain Lion I could not longer use the screen zoom feature on the magic mouse.  Scroll,swipe and click work fine.

    Welcome to Apple Communities
    Open System Preferences > Accesibility > Zoom and mark Use scroll gesture with modifier keys to zoom

  • After installing Mountain Lion, why is there Yahoo access for one user but not another?--both are administrators.

    After installing Mountain Lion, why is there Yahoo access for one user but not another?--both are administrators.

    We've had several instances where we have had to run chkdsk on arrays with over 1m files. Average completion time is approximately 72 hours. The maximum downtime window they have available is the 64 hour weekend window. File sizes and number of files were
    much smaller then than they are now.
    The idea, in theory, was to use VHDs to compartmentalize the data into smaller volumes which could be more easily managed. It would also improve performance when transferring these compartments of data as they would use sequential read/write rather than
    fragmented/random. This idea was never fleshed out in entirety, they don't split data up into little containers, but simply into big ones per project. Hence the 11m files in one container that I am currently trying to diagnose.
    Some other important facts: The VHD in question is mounted in B:/project/ as this server also allows remote workers to log in, but they are restricted to see only data in E:. Disks A-D are hidden via group policy.
    Update: icacls is failing on a large number of files within this dataset. I counted the path characters to ensure it wasn't the 255 character limit I was encountering and verified that the paths being blocked are only about 150 characters long. Once it finishes,
    I'll have to try taking ownership and then re-running it. At this point I still have no idea how long to expect. I'm running out of time as the environment will be in use again at 9AM tomorrow morning.

  • After installing Mountain Lion.  Under sound, where it says select an output device, it say no output devices found and there is no sound.  How do I fix this?  I have reinstalled the os twice and still the same.  I have also repaired permissions.

    After installing Mountain Lion.  No sound. Under sound, where it says select an output device, it says no output devices found, and there is no sound.  How do I fix this?  I have reinstalled the os twice and still the same.  I have also repaired permissions.

    Try resetting the PRAM and SMC...
    PRAM Reset:
    http://support.apple.com/kb/HT1379
    SMC Reset:
    http://support.apple.com/kb/HT3964
    Hope this helps!

  • After installing mountain lion i lost my pictures in iPhoto, lost my music in iTunes, internet became very slow. What can I do to fix this issues

    after installing mountain lion I lost pictures in iphoto, lost my musisc in itunes, my icluod is not working, internet its very slow and some other issues. There is a way how to fix these issues

    Open System Preferences > iCloud
    Deselect the box next to Photo Stream then reselect it.
    Now for your music. Launch iTunes. From the iTunes menu bar top of your screen click iTunes > Preferences then select the Store tab.
    Select: Music.  (and Apps and Books) if you want.
    Click OK.
    iCloud syncs via your Wi-Fi network so give it a minute or two to reset your photos and music.
    Slow internet ...   try turning off the modem for a few minutes, then turn it back on.

  • No video after installing Mountain Lion

    I have downloaded and installed Mountain Lion on my Mac Pro.  After the install and restart, my Mac Pro restarts however, I do not get a signal sent to my monitor.  I have attached different monitors and connected to both DVI ports with no luck.

    I just wanted to add to the conversation that this was EXACTLY what happened to me after installing Mountain Lion. All my contacts were gone. It showed the Groups on the side of the address book after one day but the contacts never showed up. I tried unchecking the box for the contacts in system preferences for the iCloud and then rechecking it again.  That didn't help either. Came across this remedy up above about taking the Address Book from the Application Support Folder and putting it in the trash. Viola! It worked. However, I would add that I had to go into the iCloud pane and check the address book box since it then became unchecked. Once I did that, they ALL loaded back up and now they are finally there.

  • My macbook pro is very slow after installing mountain lion

    my macbook pro is very slow after installing mountain lion?  Is anyone else having this issue?

    If you don't use an SSD and bump your RAM up to 8 Gb's you may experience slow speeds, but I noticed slow speeds with your general configuration in SL.
    one thing you should consider right now is, Spotlight is Reindexing your hard drive, that takes time and resources, (resources which you don't necessarily have to spare).
    If you continue feeling like your performance is slow, you have a few options with this computer (I have the same one).
    the express card slot can house a wintec SSD drive. That little door on the side of your machine is pure gold for a really quick solution for speeding up your machine. I have one in mine right now i'm using as a scratch disk for CS6 but I used to boot from it, and the speed boost was out of this world.
    You could take out the internal HDD and put in a new SSD (I have a Vertex 4 from OCZ) it is completely over kill but my experience is pretty fast and I keep up with the later MBP models colleagues have.
    There are some other options for you like taking out the optical drive (however I don't know if I'm supposed to talk about that here). Google Data Doubler.
    You need to also set it to always use the 9600 chipset, this will increase performance a lot too. to do this go to system preferences>energy saver>Better Performance. This switches the video card to the better one and makes a world of difference.
    Lastly, your RAM. after an EFI Firmware update, our computer support up to 8GBs of RAM. Do it!
    Late 08 MBP 2.53 GHZ 9600 chipset 8gb ram, Vertex 4 SSD

  • Printer won't work after installing mountain lion?

    printer won't work after installing mountain lion?

    Assuming you've first checked Software Update to see if there are any updated drivers and it's still not working, you could try resetting the printing system.
    System Preferences>Print & Scan, Control+Click or Right Click on a printer on the left and select 'reset printing system'. All printers will be deleted and need to be added again.

  • Why won't iTunes 10.6.3 work after installing Mountain Lion?

    Why won't iTunes 10.6.3 work after installing Mountain Lion?

    Instead of downloading from Apple updates on my computer, I went to apple.com, loaded it from there and the update worked fine. 

  • After installing mountain Lion my wireless mouse stopped working

    After installing mountain Lion my wireless mouse stopped working my wireless keyboard still works so I can get to the Bluetooth menu via search but once I'm there I can not figure out how to scroll down and select the mouse that is still listed as a linked device. I have already tried restarting the computer and changing the batteries. Called apple thinking they would help since I just bought mountain Lion but silly me apple does not give anything away for free. I was I never payed $20 for this p.o.s So-called operating system

    You can bypass GateKeeper.

  • After installing mountain lion the local mail boxes disappeared

    after installing mountain lion the local mail boxes disappeared.

    This is my problem too:
    All of my local mailboxes (On my Mac) disappeared from the sidebar.  However, I do not have the 'triangle' on the Inbox that I can turn to reveal the list of mailboxes -- that disappeared too (and nothing happens when I hover over "Inbox").  I do know that the mailboxes are still there, somewhere, because when I go to create a New Mailbox, I can navigate to "On My Mac" and the entire mailbox list shows up there in the dropdown.  How do I get them back onto my sidebar if the option to do that is no longer on the "Inbox" icon?

  • After installing Mountain Lion, my Time Machine won't back up ... says the sparsebundle is in use

    After installing Mountain Lion, my Time Machine won't back up ... says the sparsebundle is in use

    Standard problem in ML.. apple do not seem to want to recognise.
    Reboot the TC .. if that fails restart the whole network in correct order.. modem.. router/TC... clients.. with 2min gap.
    There are other suggestions like changing the password.. all they do is the same as reboot.
    Read C12.. most quoted Q in pondini website history. This is asked 10 times a day.
    http://pondini.org/TM/FAQ.html
    Here is another way to get a useful utility in ML.. rather than toyland version.
    How to load 5.6 into ML.
    1. Download 5.6 for Lion.
    http://support.apple.com/kb/DL1482
    Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
    2. Download and install unpkg.
    http://www.timdoug.com/unpkg/
    Run unpkg on the desktop.. it is very simple.. drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. drill down.. applications utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
    You cannot uninstall 6.1 so don't try.. and you cannot or should not run them both at the same time.. so just ignore the toyland version.. the plastic hammer.. and start using 5.6.. a real tool.

Maybe you are looking for

  • How to generate a PDF output using batch file in 10G

    Hello, I am using .bat file to generate a report PDF output. I have done this many times in 6i but for 10G I am unable to do the same. Can someone please look at the syntax below and let me know where I am going wrong. I understand that reports are d

  • ERROR In PR BAPI

    Sir, I'm getting error  while executing PR BAPI  i.e id delivery date. but i'm not getting why?. Please, help me. Thanks Manoj. *& Report  ZTEST_BAPI1 REPORT  ZTEST_BAPI1. DATA: BEGIN OF itab OCCURS 0,       bsart(4),   "Purchase requisition document

  • How to display the Full Name in Masthead of the Portal

    Where exactly in the HeaderiView.jsp I need to edit to be able to display the full name in the Masthead of the portal. e.g. Welcome Paul Jones

  • Typing in any program freezes it. I have an HP Pavilion p7-1240

    Hey, my HP Pavilion p7-1240 has been acting weird lately. Everytime I type in a browser or a program, the said program freezes, this has been happening since Saturday, the only thing I changed is the monitor. (I bought a tv, and use it as a monitor)

  • Mounting folders error

    I work for a school division where we needed a script that logs the user on to the servers User folder and Assignment folder. We had one that worked last year on the iBook carts but now our staff have macbooks and the original script no longer fuctio