After NICs teaming, DHCP can't bind the NIC, and DHCP stop working.

Hello, we have a DELL Server with windows 2008r2,
I used the windows network Bridge first, in that situation I can see DHCP can Bind the "network Bridge".
Now I need use LACP to team the NICs, I downloaded the
 Broadcom Advanced Control Suite to Teaming the 3 NICs(BCM5709C),
I followed this video, and the teaming works, but now in DHCP I can't see the virtual adapter,
https://www.youtube.com/watch?v=x2nq-qEwAzg
The DHCP got 1041 error: The DHCP service is not servicing any DHCPv4 clients because none of the active network interfaces have statically configured IPv4 addresses, or there are no active interfaces.
Same like here 
http://www.experts-exchange.com/Networking/Network_Management/Network_Operations/Q_28159948.html
Anyone had this issue before and know a solution?
Thanks
Jason
Jason

Hi,
I am investigating the issue. I did find a post here
https://communities.intel.com/message/61068 that indicates after configuring NIC teaming you might need to wait a while for the team to initialize before configuring a static IP address. Otherwise, the static IP address does not work correctly.
-Greg

Similar Messages

  • A toolbar called Searchqu got installed in my web browsers.I uninstalled Mozilla Firefox without removing the toolbar and it stopped working saying that can't connect to the server.I uninstalled and installed Firefox but it isn't working.

    A toolbar called Searchqu got installed in my web browsers.I uninstalled Mozilla Firefox without removing the toolbar and it stopped working saying that can’t connect to the server.I uninstalled and installed Firefox but it isn’t working.

    See this thread for potential ways of removing Searchqu from your system: https://support.mozilla.com/en-US/questions/790833

  • I cal apple from israel i say i gat i phone5 in the philippines and it stop working the say bring it to us apple and i gat ther the say sand it to hong kong ?

    i cal apple from israel i say i gat i phone5 in the philippines and it stop working the say bring it to us apple and i gat ther the say sand it to hong kong ?

    iPhone warranty is valid only in country of original purchase.
    If the iPhone was originally sold in the Philipines, it must be
    returned to there for repair/replacement. You must take it or
    send it to a friend/relative there to take to Apple repair in the
    Philipines. Apple does not accept international shipments for
    repair nor does Apple ship out of the country after repair.
    If Apple told you that the iPhone had to go to Hong Kong for repair,
    then the iPhone was originally sold in Hong Kong and then resold
    to you in the Philipines. In that case, take it to Hong Kong.

  • I have Photoshop CS2 for the MAC and it stopped working on my MAC. I recently bought a new MAC, an iMAC. There appears to be no way to contact Adobe about this.  What do I do? Ed

    I have Photoshop CS2 for the MAC and it stopped working on my MAC. I recently bought a new MAC, an IMAC and it doesn't work on that either. There appears to be no way to contact Adobe. What do I do? Thanks, Ed

    That because the activation servers were retired. Now for the good news:
    Adobe has provided a non-activation version of Photoshop CS2 free of charge for their CS2 license holders.
    Download the Mac version of Photoshop (not the suite) and copy down the serial number next to it.  Do not use your original serial number or cs2 disc.
    Download Acrobat 7 and CS2 products
    Uh... one more thing CS2 is PPC only.  OSX 10.6.8 has Rosetta to run legacy PPC products. 10.7 and above will not.
    Good luck,
    Gene

  • Why have the ports on the left of my macbook pro and the wifi and bluetooth stopped working?

    Hey All,
    About a week ago the two usb ports on the left of my 17" macbook pro, soundcard, wifi, and bluetooth stopped working. The power port, ethernet, remaining usb on the right are still functional. I've tried repairing the permissions and other software based solutions but to no avail. I'm worried that this might be a motherboard issue but am apprehensive about taking the ol' girl into a genius because it will probably cost more to repair than the remaining value of the system. Anyone have any ideas, can confirm my suspicion?
    Thanks!

    Well I'm using Google Chrome browser on Lion and when I type in that URL nothing happens. Except for the "This webpage is not available" banner.
    So it looks like your website is down and what you are getting on your devices are cache.
    Oh just deleted the www and now I see the page. Yup all the info looks intact. home about us products Q&A and so on.

  • I can't install itunes 10.6 after download I'm getting error code 2324? and itunes stopped working?

    After downloading the update package and trying to install it, the installation didn't work with error code 2324, and i can't open itunes on my laptop anymore?

    First of, what sort of system have you got. (Right-click My Computer in the start Menu and select properties) There are two flavours of Windows 7 x64 OEM (original equipment manufacture)  One is a total x64 system for the OS and all programs.  The other runs x64 address space for the OS and x32 address space for programs.  I had exactly the same problem with my system and microsoft office. Roll back (using the recovery console to rewrite all the original registry values before you upgraded will give you a clean system for the upgrade).  The upgrade itself should recognise the correct upgrade version for you automatically.  However, sometimes it fails to do this due to data corruption.  Go here-  http://www.apple.com/itunes/download/ and manually download what you need.  after download Right-click the file and select "properties"  and click on "unblock" box in lower right corner. close, Then right click the file again and select "Run as administrator".  If u still have problems, reboot into Safe mode.  Uninstall itunes. Reboot again to safe mode. Disconnect from internet and disable any 3rd party system watch and antivirus programs.  Reinstall itunes, then reboot normally.  If the problem still persists run a system diagnostic check using "Problem Reports and Solutions" from in Control Panel.  Let me know how you get on.

  • I can connect to the internet and everything is working o.k. but I cannot connect to the app store. Error message reads Cannot connect to App Store

    I can connect to the internet with no problems ,but I am unable to connect to the App Store. Error message reads--- Cannot connect to App Store.

    Hey William,
    It sounds as though you are having difficulty with your Mac being unable to connect to the Mac App Store. This article has some steps that may help you troubleshoot -
    Can't connect to the iTunes Store - Apple Support
    Note that the title is for the iTunes Store, the steps are still relevant.
    Thanks for using Apple Support Communities.
    Happy computing,
    Brett L 

  • Hello Apple members, my iPad Air fell on the ground and camera stopped working, please how can you help me out, this is because the camera is so important especially when I am out for events, thanks

    My iPad fell and the back camera stopped working, please help me out, thanks,

    If it doesn't come back after you restore the iPad, it sounds like you've damaged the hardware, you'll need to take it to Apple or an authorized service center.
    Matt

  • Embed animate file in Dreamweaver, make the drag and drop stop working

    The drag and drop works fine when I open the Animate file, but when I embed it using the "Media > Edge Animate", it does not work. How can I solve this problem?
    I'm using an external js file.
    Thanks.

    Need you to share the dreamweaver project along with the edge animation, to check the issue.
    Regards,
    Vivekuma

  • My digital output plug on my Imac has a broken rca in it can I disable the plug and make speakers work again?

    Does anyone know a way to restablish my speakers, there is a broken rca plug in the digital output.

    No because there is a micro switch built in the output port that tells the audio to use that output.
    1. Most times the broken jack can be removed with the correct size drill bit or small screw extractor because it is hollow. (shutdown and disconnect the power before attempting to remove the broken jack plug)
    2. If you do not have the correct tools to do the job, then take the iMac into your local Apple Store or AASP and have the broken plug remover.
    For more idea's, visit > removing a broken 3.5mm jack - Google Search

  • Mid 2011 Macbook Air - Yosemite keyboard and trackpad stopped working, the only button that worked was the power button, only one USB port works.

    I have a Mid 2011 Macbook Air.
    Upgraded to Yosemite last week.
    Three days ago I was using my Macbook Air for the first time since upgrading to Yosemite. I had been using my Macbook Air for approximately 30 minutes, I was using safari and the keyboard and trackpad stopped working (would not respond). The only button that worked was the power button.
    I rebooted and they were still not working. I plugged in a USB mouse and external USB keyboard, only one USB port would work (the Left USB port if looking at the screen) so I had to swap between keyboard and mouse.
    After logging in there is a bluetooth icon at the top of the screen with a sawtooth line through it. Bluetooth is unavailable and the bluetooth icon is missing from the system preferences menu.
    If I run a hardware test by holding D (on USB keyboard) at startup it says that no problems are found and at the conclusion of the test the keyboard and trackpad start working again. When I log on the bluetooth is working again.
    I shut down the Macbook Air and when I started it again the keyboard and trackpad and right side USB ports were all not working again. I logged in using the USB keyboard and mouse and the bluetooth not available sawtooth icon had returned.
    I ran the hardware test again and at the conclusion of the test the trackpad and keyboard started working again.
    I have tried deleting com.apple.Bluetooth.plist and com.apple.Bluetooth.plist.lockfile from /Library/Preferences/ and tried resetting SMC and Power Functions but this did not fix the issue. The only thing that seems to work is running a hardware test - obviously I don't want to do this every time I use the computer.
    I do not believe any hardware is faulty/damaged - I think it has something to do with bluetooth/Yosemite.
    I do not have the Macbook with me at the moment, if you have suggestions that I can try or additional checks/info you require please let me know and I can get back to you.
    Thanks,
    John

    Hi!
    I have exactly the same problem, and I can't find any solution.
    I can't even track down the root of the problem: the Bluetooth/Wifi module? The trackpad? The keyboard/top case? The logicboard?
    I've tried all the usual: SMC/PRAM reset, clean install, kext cache clearing.
    Any suggestion is greatly appreciated!

  • Trackpad and Trackpoint stop working all the time

    Hi Lenovo!
    I'm loving my thinkpad tablet! Only issue I have really had so far is that the trackpad and trackpoint stop working every once in a while... (as in once a month they will suddenly stop working). Then I install a driver, they start working again, only for the same problem to turn up after some more time has gone by. Last time this happened, installing the driver didn't help, nor did doing windows restore, which was very worrisome...
    I've had this laptop for less than a year so it is still under warranty, but I was wondering if there is a quick fix?
    Much appreciated!
    Ilana

    If two different ATVs are having the same problem on the same TV, the problem could be the HDMI cable or the HDMI port on the TV.

  • Mouse and Keyboard stop working after reboot

    So far the computer is working great except for the fact everytime you reboot the keyboard and mouse stop working... I did a clean format x2 and put the service pack on and I am still getting the same problem.
    Anyone have this problem or something similair ? Any ideas ?
    Thanks in advance :-)

    The problem is not your S/W install. It's with the MSI Motherboard. Your best bet is to ask MSI when a fix will be available, or go buy a different board.

  • Hi Team, Showing Yellow icons after every 15 to 20 Min and internet stop working.when we enable- disbale the network connection then will internet start working fine.Some time network connection is disable but when we renable that connection it will st

    Hi Team,
    Showing Yellow icons after every 15 to 20 Min and internet stop working.when we enable- disbale the network connection then will internet start working fine.Some time network connection is disable but when we renable that connection it will stuck on enabling
    and will not renable till i am not restart that machine. I have 350 Machine in network but facing this issue in 25 machines. Kindly help me on this issue .
    Regards
    Sahil bhateja

    Hi，
    So switch a LAN card fix this issue...seems a compatibility issue or maybe some packs or programs you installed recently cause this issue.
    Have you manually check the network adapter driver from the PC's manufacture website? sometimes, it will be a time delay before Microsoft push out the driver update.
    Check if issue exists in safemode with network, this mode will launch Windows with limited sets of files and drivers. 
    if you have a restore point, restore the pc to a previous point at which the pc is functioning fine.
    Yolanda Zhu
    TechNet Community Support

  • I have Adobe Photoshop Elements 10. It came installed on my HP Desktop. I am can not get the warp text tool to work. It has worked in the past. Once I click warp text, the little window does not pop up, and if I try to do anything else after I click warp

    I have Adobe Photoshop Elements 10. It came installed on my HP Desktop. I am can not get the warp text tool to work. It has worked in the past. Once I click warp text, the little window does not pop up, and if I try to do anything else after I click warp text, it wont let me. Just sounds the ding, alert, can still slightly navigate the program but can not use any other tools after clicking warp text. I just have to open task manager and close the program. not sure if I'm doing something wrong or maybe I just need to uninstall and re install. Having trouble finding out how to uninstall and reinstall because the program came pre installed on my desktop.

    It actually sounds like the warp text window is opening off screen.
    Resetting the photoshop elements 10 preferences should fix it.
    *Press and hold the Shift+Ctrl+Alt keys just after you start the launch of the photoshop elements 10 editor
    *Keep holding the keys down until you get a dialog asking if you want to delete the adobe photoshop elements setting file
    *Press Yes

  • After creating a pdf can I change the size of the font when uploading in acrobat and what version?

    After creating a pdf can I change the size of the font when uploading in acrobat and what version?

    What do you mean by "uploading in Acrobat"?
    (Note that if you change the size of text, it won't reflow, so you end up with a mess. Answer is, probably not useful)

Maybe you are looking for