After Performing simple Terminal Command Mac 10.10 won't boot properly

hey guys,
recently, i followed the steps in this tutorial:
How to Change View Options for ALL Finder Windows?
After doing so, my MacBook Pro OS X 10.10 does not start properly, getting stuck at the turning wheel after typing in the pw.
I noticed the terminal going through every single folder saying "find rm 'xxx' is a directory"
I triple checked the command line before.
I tried booting in safe mode.
I Hope there is a solution other than wiping all of it.

The command listed in that thread is exceptionally dangerous. Erase your hard drive and restore from backup.

Similar Messages

Mac won't boot properly unless in safe mode

Recently I updated my MacBook Pro to OS X Yosemite. I then started the process of the data encryption.
I don't know what happened, but maybe the encryption failed, because now every time I turn my mac on, it won't boot properly unless it's in safe mode.
Either it will have a black screen with a visible cursor, or just the desktop with no dock or the bar along the top and no icons, or it does boot up properly, but works extremely slowly. Like if I was to press the apple symbol on the top-right of the screen, it would take 5 minutes to actually open it. Nothing works properly.
And so I opened up my system preferences, and discovered that the Encryption is stuck on half-finished. But I can't stop it. If I try to turn encryption off it says I have to wait till it's finished. But it never does, the progress bar never moves.
If I open System Preferences while in Safe Mode, the progress bar for Encryption is grey, and underneath it says "connect to power to continue encryption". But it IS connected to power.
Have I stuffed my Mac? Is there a way to get it working again?

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB ' com.adobe.AAM.Updater-1.0 com.adobe.AAM.Updater-1.0 com.adobe.AdobeCreativeCloud com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.adobe.SwitchBoard com.apple.aelwriter com.apple.AirPortBaseStationAgent com.apple.FolderActions.enabled com.apple.installer.osmessagetracing com.apple.mrt.uiagent com.apple.ReportCrash.Self com.apple.rpmuxd com.apple.SafariNotificationAgent com.apple.usbmuxd com.citrixonline.GoToMeeting.G2MUpdate com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper com.oracle.java.JavaUpdateHelper org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.startx ' ' 879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 3694147963 1233118628 2456546649 2806998573 2778718105 2636415542 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 523110921 2883943871 3873345487 ' 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<10) print "com.apple.";} ' ' { sub(/ :/,"");print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\$[0-9]+\$\$.+\$/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"cksum "F|getline C;split(C, A);C="checksum "A[1];"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F" ("T", "C")";else F=F" ("C")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;' ' s/^.+ |\(.+$$//g;p ' '/\.(appex|pluginkit)\/Contents\/Info\.plist$/p' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' pluginkit scutil dtrace profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$(RefProc): \$Message' -k Sender Req 'fsev|kern|launchd' -k RefProc Rne 'Aq|WebK' -k Message Rne 'Goog|ksadm|probe|Roame|SMC:|smcD|sserti|suhel| VALI|ver-r|xpma' -k Message Req 'abn|bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|NVDA$|pagin|proc: t|Roamed|rror|SL|TCON|Throttli|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,Ex}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,In{p,ter},iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????|wc -l' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' " -F '\$Time \$Message' -k Sender kernel -k Message CSeq 'n Cause: -' " );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors App\ extensions Lockfiles Memory\ pressure SMC Shutdowns );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};A'$((7+i))'() { v=` eval sudo "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};';done;A9(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2 7 8;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;B1&&D73 19 53 67 55;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 54 12 56;D23 5 14 12 14;D22 6 36 13 15;D22 20 52 66 54;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D82 35 49 61 51;D82 11 17 17 20;for i in 0 1;do D82 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A8 18 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 26 50 64;B7 16;C3 52;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D73 21 0 32 19;D73 10 42 32 40;D82 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 21 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D83 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 10 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 21 48 49 49;B3 4 22 57;A1 21 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D12 4 51 32 53;D23 22 9 37 7;A9;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Mac LC 580 won't boot

My Mac LC 580 won't boot. I have tried the following in a attempt to get it to work:
Reset the logic board. Replaced the hard drive. Cleaned the logic board's end connector with contact cleaner. Cleaned the RAM modules with contact cleaner. The only thing I know for sure is that Apple's service manual for the LC 580 keeps pointing towards a bad logic board or analog board or both as the cause of death. I'm not even getting a bong from the Mac. The only thing I hear when I turn it on is the sound of the Mac running. Maybe the hard drive too. No video appears on screen either. The original hard drive was a Apple OEM Connor 800 MB OEM drive. Personally I've heard far too many horror stories about Connor hard drives from the PC world online to trust it as being reliable. It even said right on the drive that it was made in Malaysia of all places. Not a good sign if you ask me. I have managed to locate a replacement logic board on eBay if that turns out to be the cause of the Mac's death. What's the next step in getting this old Mac up & running?

Update: I have more info on what's been going on with the LC 580. I finally figured out that the 33MHz Motorola 68040 processor I installed may be defective. After switching the the original Motorola 33MHz 68LC040 & removing the RAM the Mac booted but I got a Quizzical Floppy on screen indicating the Mac couldn't find a valid System Folder. After that I figured out that the Apple SCSI 4X CD-ROM drive was defective. I replaced it with a known good Apple 8X SCSI CD-ROM drive. I then attempted to boot from a Mac OS 7.6.1 CD-ROM. I got a error type 41 & restarted with extensions off like the error told me to. I then attempted to boot from a Mac OS 8.1 CD-ROM but I got a Sad Mac error code. The error code looked like this:
0000000F
00000001. Just now I tried to boot from the Mac OS 7.6.1 CD-ROM. Again I got a error type 41. After that I booted with extensions off from the Mac OS 7.6.1 CD-ROM. I still got a error type 41 too. I then restarted & got the following Sad Mac error code:
0000000F
00000033. I also have a Mac OS 8.0 CD-ROM that I haven't tried to boot from yet. What does all of this mean & what should my next move be?

Mac Mini server won't boot after logoff, any suggestions?

My mac Mini Server will not boot after administrator logoff, I get a gray screen with the spinning progress wheel, but nothing happens. Any suggestions?

Can you boot into single user mode? If so, run fsck and post the results.

Mac Pro 2010 Won't boot after adding Ram

Just got my Mac Pro 2.8 a few days ago. My 4x2 8Gig Crucial Ram upgrade arrived today along with my SIIG FireWire400 PCIe card. It seems as though the Mac Pro won't boot with both the Crucial Ram and the Samsung Ram that came stock with the Mac Pro. I kept 2 of the 1 gig Samsung chips and put in the 2 4Gig Chips from Crucial. They are all the DDR3 1066 240 pin chips. I've moved the 4Gig chips to slots 1 & 2 and I've tried them in slots 3 & 4. I've moved the 1Gig Samsung chips accordingly. The power light on the Mac Pro blinks continuously when they are both installed. I even tried removing the new SIIG FireWire 400 card but that doesn't change anything. It seems as though combining these two types of ram just doesn't jive. Any ideas? I'm dragging the tower from queens to SoHo tomorrow to let the Apple Genius gang have a look at it.

FYI, when I did install the Registered or "buffered" 8 Gigs of Crucial Ram by themselves the system did boot up normally and a memory notification popped up and said that my ram was in the "correct" or "suggested" configuration. I can't remember the exact phrasing but the OS definitely gave me a thumbs up. So now I am trolling the web trying to find out if the Registered memory is ok. I'm fine to just have 8gigs for now. But don't want to jeopardize the stability of my system. So, Is it ok to use Registered memory and if it is, am I using a lesser quality of ram in doing so?

Mac OS X won't boot--tried everything

I did the Quicktime update that came out a few days ago... When I restarted, everything went okay until the "Mac OS X" screen. It went about a half a centimeter on the progress bar in the "Mac OS X" window and then the window disappeared and I was faced by a blue screen. I tried restarting repeatedly. Same thing every time. The "Mac Os X" window disappears. The screen changes to a lighter shade of blue after a few seconds. Every few seconds, a progress wheel like the one under the apple when you first start up the computer appears, makes half a revolution, and vanishes. I have run Techtool Deluxe, Disk Utility off of the install disk (a volume had to be repaired, but as far as I can tell repairing it didn't help at all), Mac OS X Boot Utility, reset the Pram, and booted in Safe Mode as well. Mac OS X Boot Utility said that I had a memory error--the error code was "post/0/2048". Is there anything else I can do? I don't want to have to send my laptop in to Apple.
Someone said something about a "Setup Assistant" in a reply to my earlier post, what is that? Would it help?

Hello,
this is a known issue for some who installed the QT 7.4.1 update.
Here are two suggested fixes:
(1) The first thing to try in this case (if you are in the Setup Assistant loop) is to simply choose "Shutdown" from within Setup Assistant. This may cause the QuickTime installer to resume or re-apply and a normal restart to occur.
(2)The next recommended procedure is to simply boot in Safe Mode -- accomplished by holding down the Shift key while your Mac is starting up. After the safe boot, restart normally. A number of maintenance tasks are performed during the safe boot, and you might not need to perform any additional troubleshooting. You might receive a message indicating that the update has finished installing after performing the safe boot.
Sounds like #2 of 2 should be the first thing you try.

Startup Manager displays Mac HD but won't boot to it

I have a 2008 MacPro (2x2.66 GHz Dual-Core Intel Xeon) that has been successfully running Bootcamp for a couple years with a Windows XP partition and a Mac 10.5~ partition (actually I can't remember if it was 10.6 or 10.5). We recently made a new partition for Windows 7. (This is in a classroom full of identicle MacPros, but noteably, the problem machine is the teacher's station).
As of today, the MacPro no longer boots into the Mac OS partition. It boots, by default, into Windows XP every time. Holding down option on start up brings up the Startup Manager, and the Mac HD is visible, and you can click on it or tab to select it, but then nothing happens. We tried a bootable external hard drive, but had the same problem with the Startup Manager and an inability to select anything (the keyboard and mouse both seem to work) but nothing happens when you click on your selection.
Once booted into XP, you can see the "Mac HD" option in the Boot Camp Control Panel. You can select it, but then the computer boots back into XP.
I did get the computer to start up off a Mac OS Snow Leopard install CD by holding "C" on start up. I ran "Repair Disk" using Disk Utility and found no problems. I tried repairing the disk permissions, and although they seemed fine.
I tried zapping the PRAM but there was no effect (booted into XP).
I unplugged the computer for a few minutes to reset the "NVRAM". No effect.
I tried different key combinations to attempt to boo in Safe Mode, Single User Mode, Verbose Mode, and none of those things worked, the computer booted straight into Windows XP every time.
I tried holding "d" for a hardware test, but nothing happened. Do you need to be on the internet for this? Because, I also tried, based on some suggestions I saw online, unplugging all peripherals (like our bootable firewire drive) and ethernet cables and not using a third party mouse. No effect.
Finally, I let the Snow Leopar install CD install, and although it seemed successful this had absouletly no effect. It still boots straight into Windows XP. Granted, I did not delete everything for a clean install, as I'm not sure the files are backed up anywhere.

""To update anyone watching this, we tried putting the hard drive in a different machine and still had the same boot issues,""
Are you saying that the questionable HD was put in another computer and THAT computer had the same issue as the Professors?
If so I would just backup and erase the hard drive, reformat and reinstall everything as something buggered up the Boot Manager and your going to take more time figuring it out as to redo everything.
I don't think the HD is going out but you MAY have some bad sectors on the Mac partition, if that's the problem then the bad sector might be in the bootable part and thats why it can't boot. If you want to save the HD have a disk utility do a Surface Scan to make sure.
As far as not being able to boot into Safe mode, etc, if it had a bad sector it won't be able to read the boot part which is why you can still boot into the Install DVD.
You know, looking back at your original post if you can't boot into safe mode while pressing the Shift Key after the bong, can't boot from an external HD or any of the other ways, then I would say it's a hardware problem.
Like I mentioned before, if you can put in another Dual boot HD from another machine into the Professors machine and it still won't boot into both OS's then you have confirmed it's a hardware problem.
Good luck...

Mac Mini server won't boot.

Our server is on, but when we try to access it via its screen it excepts password but returns to login page. Any ideas?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
*Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

Mac Pro 2008 won't boot from install disc - black screen

Hello,
I recently purchased a new hard drive to replace the original that came with my Mac Pro 2008. I was able to format the new drive using Disk Utility. I am now at the point where I need to install OS X onto the new drive, but the computer refuses to boot from the disc. The disc is recognized by the computer (I can access the disc and am able to use the BootCamp applications, etc.) but I just get a black screen when trying to boot directly from the disc. The computer boots fine otherwise.
I have tried the following:
I have tried using both the gray install disc that came with the computer and the Snow Leopard Install DVD disc.
I have tried booting using the "C" key and the "option" key but still receive a black screen following the chime (I've held these down for several minutes).
I have tried restarting from either install disc using the Bootcamp Assistant.
I have tried running the installation software to get it to restart from the disc.
I have tried a combination of the drives, i.e. trying to boot from the discs with just the new drive installed, just the original drive installed, and with both in bay1 and 2.
Everything results in the computer starting up, hearing the chime, and then nothing..just black screen. I have the original drive partitioned with BootCamp with OSX Snow Leopard and Windows 7 installed (I don't know that that matters).
I am at a loss as to what to try next. It doesn't seem like the superdrive because it is recognizing the disc, it just won't boot from it.
Any help is appreciated, thank you.

Clone should be a must and easy to do and learn (learn by doing! 2)
6800 would 'qualify' as 5x70 series flashed etc and same rule: 10.6.5
In the past there was 10.4.6, 10.5.6, but not 10.6.6 - even though strong need for such a DVD.
10.6.8 DVD would be excellent
Lion or ML - buy, download, make an installer flash card would be what I would do at this point.
Then keep both - dual boot as you learn and test and see what ML does and waht you had that required Rosetta to support PowerPC. See www.roaringapps.com about that.
With Carbon Coyp Cloner - was share, now commercial, great utility been around since 10.2.2 at least - this time 2003. 10 yrs.
You can clone the system folders, you can even selectively choose. You can skip copy of most of your home account and do that separately to another drive if you want.
Clone Windows with Paragon or WinClone and use Windows 7 or 8 DVD to do a system repair (automatic) or to edit the BCD file. It can and should - and all you do is boot Windows 7 DVD w/ only the one drive present and go at it. Piece of cake. But yes, Windows gets fussy if you change or remove or move. BCD to the rescue. A proper program for cloning like Paragon's "Clone OS" meant for going from disk drives to SSDs, knows that and how to do it.
Back to how to clone etc:
Clone
Disk utility has RESTORE which will also clone your system but not the Lion Recovery partition. Oddly Apple did not 'endorse' making bootable clone of the system which works too but most choose Carbon Copy Cloner - it works more consistently; it allows for smart update of the backup volume. Both can backup to a sparse disk image if desired.
Using Cloning as a Backup Strategy
http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
http://www.bombich.com/software/updates/ccc-3.5.html
OS X Lion Install to Different Drive
How to create an OS X Lion installation disc MacFixIt
Migration Assistant Update for Mac OS X Snow Leopard
http://www.apple.com/support/lion/installrecovery/
Create an OS X Lion Install disc
http://reviews.cnet.com/8301-13727_7-20080989-263/how-to-create-an-os-x-lion-ins tallation-disc
How to clone your system:
http://macperformanceguide.com/Mac-HowToClone-backup.html
http://macperformanceguide.com/Mac-HowToClone.html
http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
http://www.macperformanceguide.com/blog/2012/20120711_2-MacPro-internal-clone-ba ckup.html
The DVD is dependent on your hardware. And your hardware changed. The drivers for the 5780 and 6xxx are bundled in the OS and lacking. Minimum build thing.
Put the new drive anywhere you want. Does not matter. Can move it later. Can be drive bay 0-3 or a Firewire external or under the DVD drive.
When you clone pull the old drive and boot from the newly cloned.
After that keep a backup clone around all the time. Takes less than 10 minutes to do a smart update to copy just the changes to keep it current. So you have working copy of the system. I keep Clone "A" that I keep "as was" the system as of last month or whatever (like 10.7.4 before upgrade to 7.5).
Comes easier after doing it once and have all your ducks in a row.

Mac OS X won't boot, logo doesn't even show! Cannot reinstall OS X

I'm really frustrated. I'm logging in from Bootcamp Windows.
First, I formatted my Hard Disk yesterday, and I accidentally erased the bootcamp partition without using Bootcamp assistant, so the "free space" partition was created. I formatted the Mac OS X side reinstalled Mavericks and everything was working perfectly. Next, I wanted to install Parallels 7, using the Bootcamp partition that I wanted to reclaim. So I created another windows partition and unistalled using the Bootcamp assistant, and the free space was merged with OSX hard disk this time. So things seemed to be perfect. The Mac OS X hdd had all its original volume.
Second, this is where everything turned haywire. Because I needed to use Revit and Rhino on a larger partition, I had to install Windows again, creating a 115 GB partitiod. I used BC assistant. It installed Windows fine, but on restarting, Mac OS X did not boot. It didn't even show up as a disk when I hit the ALT key. But when I checked Disk Utility in Recovery mode, the disk was showing up fine. So I decided to reformat it again - erasing the contents and tried installing Mountain Lion, which was the only option I had using Internet recovery. The installation did not work! It said, the recovery system from the main volume was missing, or something like that.
Third, I tried to restore from Time Machine. Now, it boots, and the apple logo shows up, but then after a few seconds, the logo is replaced by a (X) sign instead, and nothing shows up. I'm so afraid my computer is permanently damaged, can somebody please tell me how to fix this? I have loads of assignments due this week, I'm about to cry

You may need another Mac so you can boot up into target disk mode. Some how you need to get that software off. You may need those OS installer disks. Are you near an Apple store or AASP? By the way it is perfectly legal to make a copy of your OS installer disk to take with you when you travel. Never leave home without it.

Start-up disc is full and mac book pro won't boot

I got the your startup disc is full pop-up a few hours ago, but didn't do anything about it. I powered down my machine, but now when I try to power it on again, it won't boot, I simply get the spinning gear and apple logo. I opened disc utility and performed a disc check and it said the disc was ok, however there is only 700 kb of free space. I want to free up some space to allow the computer to boot, but don't know how. Is there a way to do this? I don't have another mac available to me, not sure how to fix this issue.

You're Welcome. Glad you got it sorted and Thanks for posting back.
All Kudos goes to the Author of the User Tip by ds store

Mac OS X Won't Boot Up

Ever since I have installed the new Yamaha Pro Audio network driver, http://www.yamahaproaudio.com/downloads/firmsoft/network_driver/networkmidi.html My Mac won't boot up, when I turn it on, it is stuck at a violent apple/"do not" icon strobe. See the video at: http://www.youtube.com/watch?v=kUrb1LLgnJ0
I can still boot into my Windows 7 boot camp partition (ironic isn't it) which is how I'm typing this. I don't have my boot disks with me, and the shift key at start-up for safe mode has proven ineffective too. Zapping the PRAM seemed to not work as well (The startup sound doesn't even happen
Thanks for any help!

You may need another Mac so you can boot up into target disk mode. Some how you need to get that software off. You may need those OS installer disks. Are you near an Apple store or AASP? By the way it is perfectly legal to make a copy of your OS installer disk to take with you when you travel. Never leave home without it.

Power Mac G4 Cube won't Boot from CD

My Power Mac G4 Cube would not boot from the Mac OS X CD. Would you please tell me of a solution. Thank you very much.
Power Mac G4 Cube Mac OS 9.2.x

Hello! If the firmware hasn't been updated you'll need to do that first. HERE is the link if your firmware isn't up to date. Tom

2014 Mac Book Pro won't boot

2014 MBP SSD w/Retina Display won't boot. Machine was running fine and exhibited no problems. But when I try to power up the screen stays dark.

Hey RemyVSP,
It sounds like you are experiencing an issue where you computer will not power up. Here is an article with some tips on addressing this issue:
If your Mac won't turn on - Apple Support
https://support.apple.com/en-us/HT204267
Thanks for using the Apple Support Communities. Have a good one!
-Braden

SQL: System locks up and runs slow after performing simple DML record insert

SQL Version: 2008 R2
I am having a serious problem. I ran the following code to perform a simple table record insert which ran successfully. However, after running this code I could no longer access the related table. I couldn't run a query against it.
I tried to delete all the records and that wouldn't work either. When attempting to run any DML statements (i.e. Select * From vPCCertificateTypes) against this table SQL gets locked up and never returns anything and no error messages. I have
to manually stop the query. Now the entire SQL system is running slow.
Any help would be greatly appreciated. The code I ran to originally insert the records is below.
Regards,
Bob Sutor
CODE:
Begin TRAN
INSERT INTO vPCCertificateTypes (VendorGroup, CertificateType, Description, Active, Category)
SELECT HQCo, 'MBE', 'Minority-owned Business Enterprise', 'Y', 'Affirmative Action'
FROM HQCO
Where HQCo IS NOT NULL
AND HQCo <> 100
AND HQCo <> 99
IF @@ROWCOUNT <> 44 ROLLBACK ELSE COMMIT
Bob Sutor

The problem was an open uncommitted transaction against the table as you suspected. I ran your code and it cleared the transaction. In the past I would intentionally leave our the Commit statement and then if the transaction ran fine, I would
simply highlight and run 'COMMIT' and it would close the transaction. Apparently that is not the correct approach. I'll use your suggested code from now on.
Thanks for the help.
Bob Sutor

After Performing simple Terminal Command Mac 10.10 won't boot properly

Similar Messages

Maybe you are looking for