After Reset LED Off

Hello, after the reset with the Airport Utility will not boot the Time Capsule. The LED is off! If I pull the power plug and a few minutes wait, everything goes back. When I try a reset on the Airport Utility, it is not folding. The LED remains off. I have already reset the Time Capsule to factory settings. What can that be?

Ok.. Gen4 has some fault that is at this point unrepairable.
It is AFAIK at this stage bad soldering.. as general poking and prodding... or the occasional suddenly crash down on the table can bring it back to life.. don't do it powered as the hard disk is running. But a solid whack on the top or bring the TC down on the bench with solid hit, can bring them back to life albeit briefly.. long enough to recover files if you ware lucky.. remember not powered.
The problem is the TC has failed to boot.. that is why it is dead.. but it is supplying power to the hard disk which you can feel spinning.. or hear it if you put your ear on it.
At this point in time the best thing is to get Apple to replace it.
How you do that depends on where you are in the world and your local warranty support.
Certainly if it is even a day less than 2years, the trick is to buy something with applecare that covers the TC.. ie Apple TV.
See the extra info here.
https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair/gen4-a1409-issues

Similar Messages

ICloud Drive will not work on my iPad 3. Pages crashes when I try. Setting resets to off after it crashes. any suggestions?

iCloud Drive will not work on my iPad 3. Pages crashes when I try. Settings resets to off after it crashes. any suggestions?

From the Ipad manual - actually the same in Ipad, Ipod, Iphone --- the support site listed has frequently asked questions on Icloud drive.
Set up iCloud Drive
You can set up iCloud Drive using Setup Assistant when you install iOS 8, or you can set it up later in Settings. iCloud Drive is an upgrade to Documents & Data. When you upgrade to iCloud Drive, your documents are copied to iCloud Drive and become available on your devices using iCloud Drive. You won’t be able to access the documents stored in iCloud Drive on your other devices until they are also upgraded to iOS 8 or OS X Yosemite. For more information about upgrading to iCloud Drive, see support.apple.com/kb/HT6345.
Set up iCloud Drive. Go to Settings > iCloud > iCloud Drive, turn on iCloud Drive, then follow the onscreen instructions.

HT201252 I can not turn off find my iPhone after resetting my ipad

can not turn off find my iPhone after resetting my ipad. I reset my iPad and now the iCloud account is associated with an old account. How do I associate iCloud with my proper appleID?

I was able to restore my iPad using iTunes. Thanks for replying. I used the technique described here If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support

What to do after resetting the MBP SMC?

I have a MBP 2011 model. After having slow frame rates on games running on bootcamp, I decided to do the SMC reset as recommended by various forums and discussion threads, and the SMC was successfully reset, HOWEVER..
After restart..
- Battery icon has a "X" on it as teh battery is damaged.
- Keyboard back lights are not working.
- Sleep mode not entered with screen led off.
- Fans are always running at full speed.
- Windows does not start fully.
- Other people reported USBs don't recognize connected devices.
I know all these settings are managed by the SMC and that's why they're not working, so nothing is wrong with the hardware. I serched for these settings in OSX but couldn't find. And all discussions on the net are only talking about how to reset the SMC but not what to do after that.
How do I get these things back?

hi luxuryliner67,
I have already reset pram, here you can read all things I've done and why >
[https://discussions.apple.com/message/22661511#22661511]
when you speak about "chimes"...you mean the "apple restart sound"? I have to hear it at least a couple of times? I'll do...again everything ;-)
finally I'll try also to disconnect the battery connection (I have opened 2 months ago my mac to upgrade memory) as someone suggested here >
https://discussions.apple.com/thread/4270970?start=15&tstart=0
if you have any other suggestion, please! you are welcome
thank
andrea

When I boot up the iphone 5s after it being off it will load then as soon as it gets to the lock screen it goes to sleep right away it will show me the lock screen for a second if that

When I turn on the iphone 5s after it being off it will load then show me the lock screen for a second if that and then go right to sleep mode right away as soon as the lock screen comes on

Hi Apple user 789,
Welcome to the Support Communities!
The following article will provide some troubleshooting steps for your iPhone.
iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting
http://support.apple.com/kb/HT1430
If that does not resolve the issue, refer to page 146 in the iPhone User Guide to Reset All Settings:
iPhone User Guide for iOS 7
manuals.info.apple.com/MANUALS/1000/MA1565/en_US/iphone_user_guide.pdf
The final troubleshooting step would be to restore your device:
iTunes: Restoring iOS software
http://support.apple.com/kb/ht1414
Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition. Before restoring:
Verify that you are using the latest version of iTunes.
Back up your device.
Transfer and sync content to your computer.
I hope this information helps ....
Happy Holidays!
- Judy

Even after resetting apple id password still won't activate my phone

I did a reset erase all contents and settings but i'm stuck at activation lock! The iphone is mine and email is correct but even after i reset my password, IT STILL WON'T ACCEPT THE NEW PASSWORD :(( please help! Thank you.

moniiice
Re: Does reset all content and settings automatically sets Find my iphone off?
Jan 27, 2014 8:54 AM (in response to KiltedTim)
But when i sign in my icloud account on the activation lock, it still won't accept it. Even if i tried resetting my password. I believe that i use the right icloud account but still it won't activate it. I tried locating my device on find my iphone and the device was not there, does it mean my device has already been erased?(i resetted all content and settings) but why does it still have an activation lock after reset? Tried everything but still no luck :( reset apple id or password but still nothing :(

I downloaded ios7 and now some apps won't open even after resetting them. Don't won't to lose my info by deleting them and starting over. What to do?

I downloaded ios7 and now some apps won't open even after resetting don't won't to lose my info by deleting and starting over.. What to do?

Try close all inactive apps
1. Double tap the home button to bring up the multi-tasking view
2. Swipe up on the screenshot of the app you want to exit.
3. The app will fly off the screen

Hi. I tried to change my old icloud account on a new one. After reset the settings I need to enter my old Apple ID account and password, that I don't remember.

Hi. I tried to change my old icloud account on a new one. After reset the settings I need to enter my old Apple ID account and password, that I don't remember.
I do not remember it because when I bought the my iPhone 4s in 2011 I didn't understand how it works and asked a representative to set it up for me. The representative helped me and gave a piece of paper with login and password but I lost it a long time ago.
Before resetting the settings I turned off "Find my iPhone" function, but it anyway asks me to enter my old Apple ID and password. I have the original box, documents, receipt. So how can I solve this problem?

You do not have to call US, but you need to call. Or else.
Contact Apple for support and service - Apple Support

HT201263 my ipod touch 4th gen isnt work after a long time with 0 percent battery power.Then its not working. computer doesnt respond to my ipod .only black screen is appearing it even not wake up after reset it what can i do please help me

my ipod touch 4th gen isnt work after a long time with 0 percent battery power.Then its not working. computer doesnt respond to my ipod .only black screen is appearing it even not wake up after reset it what can i do please help me

After being connected to a charging source overnight try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Camera on 5s is frozen even after reset any ideas? Thx

My camera is frozen on my iPhone 5s even after resetting...any ideas? Thx

That is NOT unfreezing it for me. It returns to home page now after about thirty seconds of total freeze (worsened from last night).
And now some really strange things are adding to it, like when waking and sliding to unlock, the tab is sticking for several seconds to the right before opening home page. Nobody seems to know whether apps are saved in sync for easy load following a restore. (??)
Edit to add: when I try the hard reset, it simply prompts whether I want to shut down, so I guess yes, it does finally help to exit the frozen shutter, though as I said, it releases after about thirty seconds.
One more edit: I turned my iphone off and restarted it to find, knock on wood, that the camera's working now. Will see where it goes from here.
null

Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

hi,
I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives Ethernet LED = Off; Radio LED = RED ; Status LED = RED and only next listing in the screen:
Xmodem file system is available.
Flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error during initializion of the flash filesystem.
The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
ether_init
tftp_init
boot
When I type this commands, it doesn't help at all. The output will be following:
ap: flash_init
Initializing Flash...
flashfs[0]: out of memory
...done Initializing Flash.
ap: ether_init
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ap: tftp_init
Unable to get our ip address: no "IP_ADDR" variable set
ap: boot
Loading ""...; permission denied
Error loading ""
Interrupt within 5 seconds to abort boot process.
Boot process failed...
ap:
what i do ? please help , thanks

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red

Safari misbehaving after reset

I've been having serious beachball issues with Safari, so in my troubleshooting one of the first things I tried was to reset Safari. The result has been that the beachball issues haven't gone away, and more problems have arisen, specifically:
1) Using CMD+[comma] to get to Preferences doesn't work the first time I do use it in a session. The Safari menu flashes blue, but nothing happens. When I hit the key combo a second time, the Preferences come up.
2) Once in Preferences, when selecting a particular preference in the toolbar, sometimes that preference does not come up, and I have to click away to another preference, then click back. This happens most often with the add-on preference Safari Cookies, which leads to...
3) I have Safari Cookies installed, and after resetting Safari, this preference doesn't work, the Cookies tab displays no content — not even my saved favorites — and the About tab is blank.
I've been in contact with the programmer of Safari Cookies, and we're both stumped.
But here's the kicker: Out of frustration, I ran just about every **** thing in Onyx — clearing system and user cache and logs, etc. After doing so, Safari was back to normal, with Safari Cookies working again — for about a week. Then it was right back to beachballs and preference problems, and I can't think of a single thing that would have triggered the return to the broken behavior.
Anybody got an idea or two?

Hi,
A common troubleshooting tip we suggest is to login to anohter user account, launch Safari there. If you see the same problems, that can be indicative of a problem with the startup disk. Launch Disk Utility from the admin account. Select MacintoshHD in the panel on the left then select the FirstAid tab. Click: Verify Disk.
If Disk Utility reports problems, follow the instructions here for Using Disk Utility to Verify or Repair Disks. You will need your install disc.
If Safari runs ok in another account, then go to Safari / Preferences - Extensions. Turn that off, see if it makes a difference.
If it's not Extensions, follow the instrucitons here for troubleshooting Safari third party plugins.
Safari: Unsupported third-party add-ons may cause Safari to unexpectedly quit or have performance issues
And try troubleshooting the Safari .plist file. Quit Safari. Open a Finder window. Select your Home Folder in the Sidebar on the left. It has a small house icon. Then open the Library folder then the Preferences folder. Move the com.apple.Safari.plist file from the Preferences folder to the Desktop. Now launch Safari. If Safari functions as it should, move that .plist file to the Trash.
Carolyn

Firefox slow wireless but fast wired. No issues running IE wireless. Tried system restore, fact. reset, turned off accl, disabled addons, run in safe mode.....

So i have an HP e118dx running on windows 8.1 with very little software on it. Currently running FF 37.0.1 and in wireless mode it always hangs up, runs slow, or times out. When plugged in it runs just fine. Can get on net using IE via wireless and no issues. So it seems to be something specific to FF on the wireless side. Thought it might have been my wireless card but running IE just fine seems to rule that out.
Have already tried system restore a few times, factory reset, turn off hardware accel., run in safe mode(FF), disabled add ons and nothing seems to help. If i have tabs open while wired, then go wireless and refresh the pages or browse on the already open pages i tend to get a couple minutes of trouble free experience before it slows to a halt again.
To recap....FF on wireless=slow and wired=fast. No difference when using IE wireless---always fast.

Not sure what you mean by # of connections being made. Not sure if that means tabs open, or folks using the actual wireless network. A while back when i was going through this with the isp i got a crash coarse on how to go into the modem and check a bunch of different stuff, as well as reset things. When looking in there only 1 or 2 computers showed on the network. The network is password protected......i guess protected only to the extent that a pswrd can. Not certain if someone nefariously connected somehow.....didn't show up when looking for users on the network though.
The first bullet point......Not sure how to do any of that so i'd say no.
Second bullet point......Yes, did lots of clearing temp files, caches, history, etc. along with systems restores and factory resets. although not exactly sure what you mean by dns cache. Might have done this but don't recall specifically seeing that.
Third bullet point.....It doesn't make any difference on this end whether its on no proxy, auto proxy, manual proxy. While i have no idea what all this stuff does/affects performance i played with it on all different settings and nothing changed here. Put it back to no proxy.
The thing is even when my wireless FF is acting up other devices in the home can be on the wireless with no issues. Think the other devices are using Chrome and some phone wifi hookup. Keep in mind if i switch to IE on the same device with FF windows open the IE will run just fine. At any given time there should only be 1-4 devices on the network so i'm guessing that shouldn't overload anything. Besides none of the other devices ever seem to come into this issue.
There always seems to be some issue that pops up after updates. Can't ever just leave working things alone.

HT1766 My Iphone 4s dont open up after i switched off it. when i open it it is stuck in the apple logo mode. I cannot switch it on again. is their any way to backup my photos since i cannot switch on my phone?

My iphone 4s dont open up after I switch off it. When I click the switch on button it blinks the apple logo in the black background. Is there anyway that i can backup my photos since I cannot open my phone?

Hello Ganewee,
Thank you for posting in the Apple Support Communities. It is certainly impossible to use your iPhone if it won't power on. I found some steps that can help with an issue like this:
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 15 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
You can find the full article here:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
If you get to step 6 where you have to restore your iPhone and your iPhone is recognized in iTunes, I would try backing it up before going through the restore. You can find steps to backup your iPhone here:
iOS: How to back up
http://support.apple.com/kb/HT1766
I hope this helps!
Best,
Sheila M.

HT201412 my ipad3 does not turn on after it went off while using it, anyone with same experience and have it resolve already?

my Ipad 3 will not turn-on after it went off while using it, anyone with the same experience and have it resolve?

Is the battery charged?
Frozen or unresponsive iPad
Resolve these most common issues:
    •    Display remains black or blank
    •    Touch screen not responding
    •    Application unexpectedly closes or freezes
http://www.apple.com/support/ipad/assistant/ipad/
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
 Cheers, Tom

After Reset LED Off

Similar Messages

Maybe you are looking for