After standby no 1Gbit Lan

Hello,
I use a T500 5253 with a Intel 82567LM Gigabit network adapter.
After standby, I loose the gigabit connection to the router. You have to deactivate and activate the adapter again, otherwise it will be fixed at 100 Mbit/s. The driver built-in diag method fails and return only "100 Mbit possible" after a standby.
LAN driver version: 10.1.17.0
Intel ProSet version 18.2.63.0
the energy settings are on maximum, the network card is not allowed to reduce speed for energy saving.
Does a work around exists?
Thinkpad T500 2082-52g
HDD changed into SAMSUNG HM500LI
Microsoft Windows 6.1 Built 7600 - Windows 7

I would begin by updating your version of OS X to 10.7.4, if you have not done so already, according to your profile. That indeed may solve it.
Hope this helps

Similar Messages

Swing application eats CPU on resume after standby

My application contains a mix of regular Swing components and about 200 (small) custom components (JPanels) that draw themselves. The problem is that if put my laptop into Standby, then restart it, the application eats CPU. It goes from ~4% pre standby to ~48% after standby. Totally repeatable. There is only the main thread, the AWT thread and a couple timers firing: one to get data from a server and one to redraw the custom controls to make the control blink (calls repaint() to cue up a call to paintComponent()). I put timing code in the two timer driven threads and both are running fine. NOTE: each of the custom components is just a rectangle with a short text string in it. Think checkerboard with text. The background color is all that is being changed. It's basically a grid of alarm/status "lights".
I did some searching and only found a reference to a drawing bug that was fixed back in 1.4.x that had to do with WinXP and dual-headed computers.
Note that another simple Swing application I wrote (no custom controls), doesn't appear to behave this way, so I suspect it has to do with the custom drawing stuff (rolling my own paintComponent() method).
Any thoughts on how to figure out what is eating the CPU? I'm using NetBeans 6.7 and JDK 1.6_14 under Windows XP.
Edited by: garrysimmons on Sep 15, 2009 1:52 PM
Edited by: garrysimmons on Sep 15, 2009 2:57 PM
Edited by: garrysimmons on Sep 15, 2009 3:02 PM

It doesn't matter if it's a Swing timer or a Util timer. It behaves the same either way. That was one of the first things I tried.
I ended up refactoring the code to go from a grid of individual controls (think checker board where each square is a control that draws itself), to a single "board" control that draws a grid. That seems to have fixed the issue. I can go in/out of Standby and the app doesn't eat a ton of CPU any more. The real problem may still be there, just too small of an effect to notice.
I don't know why the original design would work fine before a Standby, but not after. Having ~200 little controls doing repaints twice a second must confuse something in the JVM/Windows versus having 4 large controls doing the same amount of drawing.
It's working, so time to move on.

Satellite A100-049: CDs and DVDs don't read after standby

I have a new satellite A100-049 that came with vista home premium pre-installed. After returning to the computer from sleep/standby (Whatever the mode is when the light pulses yellow) no discs can be read in the drive. The disc will spin continually but nothing will happen.
Everything works fine when the computer is turned on first time, but after sleep it stops reading discs. Is there anything I can do about this?

It doesn't recognize it when i re-insert it or put it in fresh after standby. It just keep spinning without loading. Wierd thing is, if i try to load a program with the disc spinning and by clicking on the desktop icon and then take the disc out while it isn't loading I get a message saying please insert disc

After installation, the mobo LAN port is not working? urgent, help ple

I just installed archlinux on my new i7 860 Asus p7p55d-e Deluxe build, but after the installation the LAN port is not working anymore. Before this, this Lan port works perfect in windows as well as in the arch installation. But after the installation, the led is orange and is blinking slowly, windows complains that the cable is not properly plugged, and even arch installation can't pull DHCP from it also.
Luckily, the mobo has another lan port, so I have to plug the cable out and to the second port, but I couldn't seem to be able to find anyway to enable the first Lan port anymore?
Have you seen anything like this, what possibly is the reason?
Thanks, any help will be appreciated.

heleos, thanks for the reply, the first thing I check is BIOS. There is definitely nothing wrong with that, since I loaded the default one.
It is really strange, it seems no matter what I do, the 1st port which used to work, simple doesn't work, but the second one works fine.
But after some poking around with the "ethtool", it starts to work again. I have no idea what cause the disfunction and what magically heal it again.
Now I am really curious.
Last edited by mark.altern (2010-04-18 09:52:09)

Audigy2 NX USB not recognized after Standby-M

Hi,
if somebody uses a Laptop there is only the possibility to use an USB, Firewire or PCMCIA Soundcard.
I am using the Audigy2 NX USB with my portable PC (Windows XP SP2 installed).
When I close the lid of my Laptop and it goes into Standby-Mode and then reactivating Windows again an Error Message appears when Music is going to be played.
The Device seems to have a driver problem.
I need to reboot Windows XP everytime again when I want to play Sound. :angry:
(I've installed the newest Soundblasterdrivers and Firmware with Autoupdate!)
Questions:
: Is this a known problem?
2: Is there a solution?
3: Which external Creative-Soundcards do support Notebookfeatures like Standbymode?
4: Why aren't 64bit drivers released for Win XP64bit's

PAPPL wrote:
Hi,if somebody uses a Laptop there is only the possibility to use an USB, Firewire or PCMCIA Soundcard. I am using the Audigy2 NX USB with my portable PC (Windows XP SP2 installed).When I close the lid of my Laptop and it goes into Standby-Mode and then reactivating Windows again an Error Message appears when Music is going to be played. The Device seems to have a driver problem. I need to reboot Windows XP everytime again when I want to play Sound. :angryI've installed the newest Soundblasterdrivers and Firmware with Autoupdate!)?Questions:: Is this a known problem?2: Is there a solution?3: Which external Creative-Soundcards do support Notebookfeatures like Standbymode?4: Why aren't 64bit drivers released for Win XP64bit's
. Not a known problem at least I dun read it here.
2. The problem maybe with Windows itself cos I known that the OS have many problem with standby. If you go to microsoft website and do a search in their kbase, you will find many problem occur with USB device after standby.
3. As say, it may be a problem of OS and not the card.
4. There are 64bit driver being developed but just not release yet. This is what I found on their kbase.
http://us.creative.com/support/XPx64/
Here's one solution I found at microsoft kbase.
Do not configure your computer to turn off USB devices to save power while the computer is on standby. To do this, follow these steps:
. Click Start, click Control Panel, and then double-click System.
2. In System Properties, click the Hardware tab, and then click Device Manager.
3. In Device Manager, double-click Uni'versal Serial Bus Controllers.
4. Right-click USB Root Hub, and then click Properties.
5. In USB Root Hub Properties, click the Power Management tab, and then click to clear the Allow the computer to turn off this device to save power check box.
6. Repeat steps 4 and 5 for each instance of USB Root Hub that is listed in Device Manager.

Processor speed after Standby Mode

I have the T400 with Windows XP (32bit). Dual P8600 2.4GHz processors & 3GB memory. Fairly new computer so there is plenty of space.
I run a macro out of Excel every day. When I run the program it takes about 15 to 20 mins and Excel struggles to move. This is normal with this laptop and it is annoying. I found that there have been times when the program runs fast as it should - fast as in 4 minutes. Processing speed is clearly faster but all programs are the same. I have also come to realize today that it runs faster after it comes out of Standby Mode. If I shut down and then re-start the computer and then run the program out of Excel it takes 20 minutes. If I start up, then go to standby then come out and run the program it runs in 4 minutes.
What would cause this? Is there some background process that stops after Standby that would allow the processors to perform as they should?
Thanks

is your CPU throttling down. Download HWinfo32 and check the cpu speed when the excel is running slow (the 20 minutes).
also are you running the laptop with the battery inserted? and do you have the latest thinkvantage power manager installed? what version of the bios firmware are you running?
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Thinkpad X300 with windows xp sp2 gets blue screen after standby.

We have a Thinkpad X300 (with windows xp sp2) gets blue screen after standby. I mean after you close the lid then open it. Anyone has see this kind of behave before?
Thanks,

I have found the solution to this problem - hope you are still watching the thread.
Express install in parallels seems to be the culprit. Do a custom install instead and set your own virtual hard disk size. I set mine to 12 Gb (12000 Mb)and made it a fixed size instead of "growing" or whatever the heck parallels calls it. I also chose shared network instead of "bridged" (I read that someone else had identified this as part of the problem).
After making those changes it worked like a charm.

Airport does not reconnect after standby...

Is anyone having issues w/ wireless not reconnecting after standby? In order to resolve the problem, I have to turn airport off then back on. Most of the time I can get back on using on/off method, but seldomly I have to reboot. This is my config:
SSID is not broadcasted, using capital letters and numbers for SSID Name.
WPA TKIP set for router encryption. WPA Personal selected on Airport.
I don't seem to have this problem on my Macbook running Leopard, so I'm pretty sure it's hardware/driver related to my Macbook Pro. I have to keep tabs on this, but I almost think this problem does not appear when a network SSID is broadcasted and/or unecrypted. It could be my imagination but not sure.
Any ideas or same issues out there?

I always have the same problem; I assume it has something to do with the fact that I regularly switch my cable modem to "standby" when done surfing the internet. Seemingly Airport loses the signal (or whatever) because the modem isn't feeding a signal being in standby mode? When I turn the modem back on, I have to turn Airport back on as well. So far, I've just felt it to be a small inconvenience.

Redo Log Apply after Standby Restarts

hi all,
To start my learning on Data Guard, I've successfully followed the manual steps to create a physical standby database. What I noticed is when I restart the standby database, the received redo log aren't automatically applied until I issued the following command:
ALTER DATABASE RECOVER MANAGED STANDBY DATABASE DISCONNECT FROM SESSION;Is that normal? If yes, is there a way to make redo application remains automatic after standby database restarts?
Thanks in advance.

When you configure the DataGuard in an SQL environment you need to manually start the redo apply process after the Standby Database is mounted. You can script the database startup and include that when "select database_role from v$database" is Physical Standby then "ALTER DATABASE RECOVER MANAGED STANDBY DATABASE USING CURRENT LOGFILE DISCONNECT;"
OR
Yo can configure the DataGuard under the broker control which will start the redo apply process automatically when the Standby Server starts.
Sudhir.

Satellite Pro A300 - After standby the mouse stops working

Hi all,
Really hope you can help me out wiht this problem as I believe I have tried anything I know and my next step is formating the whole computer again and still not knowing if it will work this time, as this is what I just did, when upgrading to win 7.
I have 2 problems:
When computer goes on standby and I start it backup - the mouse stops working, unless i move it to another usb-port. I get a message aswell about usb can perform faster...
Another problem is a program freezing at this point aswell, this program is Oracle JDeveloper, do not know if this has any relevance??
I have tried updating EVERY driver from toshibas webpage- theese problems still occur...
Please help!
Would rather not format again...!
// Christian

Hi
Can you please tell us what Windows 7 version you have installed? I mean if you have 32bit or 64bit.
Is this right that you are using an external mouse?
Does the touchpad work after standby mode? If yes I think its something wrong with the external mouse maybe.
By the way: Make sure that you are using newest BIOS version. You can find it on the Toshiba page.
And regarding the Oracle question I think you should contact the Oracle support directly. ;)

After standby AirPlay Mirroring tranfers only sound and no video

After standby, my Mac (mid 2012) with Yosemite is just transferring audio and no video to Apple TV (the newest one)... When i Reboot the mac all works great.
What is the problem please ? Thanks for any help !

You have to follow the following two steps when doing AirPlay from iMac:
Step 1: Open System Preferences and click on sound. Then Click on the output tab and select Apple TV instead of Built-in
Step 2: Click on AirPlay on the Menu bar and Click on Apple TV as you have already done.
It will work just fine. The trick is that you have to set the Sound option BEFORE you send the video to ATV. I don't know why this is but it is not automatic unlike MacBook Air. When you turn off AirPlay you have to change the sound option to Built-in to go back to listening to sound on your iMac.

No wlan after standby modus

hey,
I have no wlan connection after standby. I have to deactivate and then activate again...
Can anybody help?
Macbook Pro Mid 2012 Yosemite 10.0.2

hey,
I have no wlan connection after standby. I have to deactivate and then activate again...
Can anybody help?
Macbook Pro Mid 2012 Yosemite 10.0.2

Loss connection SMB on OSX 10.6.8 after standby

Hello,
I have a problem on an iMac with osx 10.6.8. After standby when I go to the MAC before I lose my connection SMB. I have to restart the Mac in force because it also blocks the judgment by the system.
Do you have a solution to my problem, thank you in advance.
Regards

Your crashreport is: 
https://crash-stats.mozilla.com/report/index/bp-12330949-db76-498f-af0a-2c9eb2111101 
Firefox 7.0.1 Crash Report [@ RapportTanzan7.dylib@0x7f7f ] 
Similiar crash here: http://support.mozilla.com/nl/questions/891272 
This is a crash in Trusteer Rapport. On Windows we were able to solve this problem by having users updating to the newest version of Rapport. You may need some help from the Trusteer helpdesk, because it seems like the automatic updates does not allways update to the newest version. 
See: 
https://support.mozilla.com/nl/questions/888019 
https://support.mozilla.com/nl/questions/887181

Qmaster and 1Gbit LAN

Will Qmaster works with a simple 1Gbit lan? I mean... is there a way to use 5 Macs to share a compressor rendering without having a Fiber Channel connection but just a simple lan comnection?
If yes, how should i configure qmaster controller, client and Compressor?
thank you.
Message was edited by: maxnix

well... seen that someone has answered me i have a lot of questions about this
first of all this is my hardware:
1 xserve
1 xride (where are stored proxy files and thumbnails for final cut server) connected to xserve via fiberchannel
2 mac pro connected via 1Gb lan
2 macbook connected via 1Gb lan
1 macbook pro connected via 1Gb lan
1 nas connected via 1Gb lan
this is the software:
compressor installed on all the MACs
final cut server installed on the xserve
we need this system to encode mov files and create flv video for internet streaming content; the FCS watches a folder in the NAS (where we save the mov files) and then creates the video assets and the flv files. the flv file created will then be moved to another folder (still by automations)
now a couple of issues:
1) I've followed all the instruction to create a distribuite processing, it works but it does distrbuite one job per processor and don't share a single job for all the processors... in this way it doesn't increase so much the transcoding speed.
2) I post this issue here but perhaps i should post it in another topic... anyway... the FCS watcher (particularly the automation that creates flv) suddenly starts to transcode all the file already transcoded. to make the situation worse, the FCS job monitor allows to cancel just one job at time... we have thousands of movs in that folder so you can understand how big the problem is
well, thats all
hoping that it will not be more difficult to understand my english than to solve the above issues
thank you a lot

X31 WinXP USB after standby Code 38

Hallo everyone!
I have a very annoying problem. My Thinkpad X31 supports internally only 802.11b that is too slow today. So I got Fritz!WLAN USB Stick which can 802.11g.
The Problem: The stick stops to work after standby. Worse: Not always. Rarely It works after first standby but by second one for sure. In Device Manager under USB controllers I can see that "USB mass storage device" has a trouble :
Windows cannot load the device driver for this hardware because a previous instance of the device driver is still in memory (Code 38)
I guess there is not a problem with WLAN USB Stick but interplay of Windows driver with hardware.
Has anyone idea how i get clue with this problem?
Thanx in advance
P.S. Microsoft recommends to restart pc. funny guys. :-E

It doesn't matter if it's a Swing timer or a Util timer. It behaves the same either way. That was one of the first things I tried.
I ended up refactoring the code to go from a grid of individual controls (think checker board where each square is a control that draws itself), to a single "board" control that draws a grid. That seems to have fixed the issue. I can go in/out of Standby and the app doesn't eat a ton of CPU any more. The real problem may still be there, just too small of an effect to notice.
I don't know why the original design would work fine before a Standby, but not after. Having ~200 little controls doing repaints twice a second must confuse something in the JVM/Windows versus having 4 large controls doing the same amount of drawing.
It's working, so time to move on.

After standby no 1Gbit Lan

Similar Messages

Maybe you are looking for