After the reboot, ssh demon is not starting up

Hi Folks,
After the reboot, ssh demon is not starting up in Solaris 9 server.
1) Does any change in package?
2) If it need to install the new package, sunfreeware seems to not active.
# /etc/init.d/sshd start
Starting SSHD
:/# OpenSSL version mismatch. Built against 90702f, you have 9080cf
:/# pkginfo | grep open
application SMCossh openssh
application SMCossl openssl
:/# pkginfo -l SMCossh
PKGINST: SMCossh
NAME: openssh
CATEGORY: application
ARCH: sparc
VERSION: 3.7.1p2
BASEDIR: /usr/local
VENDOR: The OpenSSH Group
PSTAMP: Steve Christensen
INSTDATE: Jun 22 2007 15:20
EMAIL: [email protected]
STATUS: completely installed
FILES: 51 installed pathnames
10 shared pathnames
11 directories
10 executables
1 setuid/setgid executables
3059 blocks used (approx)
:/# pkginfo -l SMCossl
PKGINST: SMCossl
NAME: openssl
CATEGORY: application
ARCH: sparc
VERSION: 0.9.8l
BASEDIR: /usr/local
VENDOR: The OpenSSL Group
PSTAMP: Steve Christensen
INSTDATE: Jan 10 2012 10:52
EMAIL: [email protected]
STATUS: completely installed
FILES: 1563 installed pathnames
1 shared pathnames
42 directories
27 executables
23412 blocks used (approx)

Clearly it's telling you what is wrong:
Starting SSHD
:/# OpenSSL version mismatch. Built against 90702f, you have 9080cf
Why not use the ssh that comes with Solaris 9 instead of the opensource version?
SUNWsshdr and SUNWsshdu or the Secure Shell Cluster (SUNWCssh):
http://docs.oracle.com/cd/E19683-01/817-0488/installbugs-222/index.html

Similar Messages

HT4972 after the update, my iphone is not starting, and itunes is not reading my iphone, itunes tells me that there is no sim card inserted, which is wrong, any solutions?

after the update to IOS 5.1.1, my iphone is not being activated, it tells me ''your iphone could not be activated server is temporarily unavailable. . . .'', and itunes is not reading my iphone, itunes tells me that there is no sim card inserted, which is wrong, any solutions?

Does your computer recognize other iPhones?
If the problem is only with this iPhone, try following along with this Apple doc -> iOS: Unable to update or restore
If the computer doesn't recognize other iPhones, try following along with this Apple doc -> iOS: Device not recognized in iTunes for Windows

After upgrading to 27, firefox will not start. Saw an error message during the upgrade process.

After upgrading to 27, firefox will not start. Saw an error message during the upgrade process but cannot remember.
Tried to run firefox.exe -P but receive error message:
XML Parsing error: undefined entity
Location: chrome://mozapps/content/profile/profileSelection.xul
Line number 18, Column 1:
<dialog
^
Running on Windows XP SP3. No problem whatsoever before upgrading to 27. Sending this from Chrome as I cannot open Firefox at all.

Thanks jschaer2000: after starting it once in safe mode, I closed Mozilla and tried several restarts in normal mode. So far, all worked:-)
Thank you very much again.
Still the automatic update process bothers me: it took me several days to discover the reason to the malfunction, since when I removed the problematic version from Add and Remove Programs, I didn't pay attention at first that it was another version, not v26 which I installed from my folder.
In addition, I like to save the installation files before I run new programs and if I didn't have v26 exe file, I couldn't have operated Mozilla at all. Not that it was fun to remove and install again each time v27 didn't react, but it was better than nothing, I still prefer Mozilla over its competition.

My ipad2 shuts down completely after I press the sleep button and does not start.... Help please

My ipad2 shuts down completely after I press the sleep button and does not start.... Help please
This started since the latest update!!!!!!!!!!!!!!

Hi Alkaf,
Welcome to Apple Support Communities.
It sounds like your iPad will not turn on. Take a look at the iPhone article linked below, it provides tips that will help resolve power issues for both iPhones and iPads.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
-Jason

I had an iMac with Snow Leopard 10.6.8, I downloaded and installed Lion, did not make me any questions. After the reboot I get this fatal error: Panic(cpu 0 ......) Kernel trap ......

I had an iMac with Snow Leopard 10.6.8, I downloaded and installed Lion, did not make me any questions. After the reboot I get this fatal error: Panic(cpu 0 ......) Kernel trap ......

Please post the Kernel Panic report. You will find it at /Library/Logs/DiagnosticReports per
http://support.apple.com/kb/ht2546
When we look at the KP report we may find some clues why it is occuring.

After the trial period I bought when starting an application, but does not advance. As I can activate it?

After the trial period I bought when starting an application, but does not advance. As I can activate it?

Hi,
Do you get any error while activating Muse, or could you please provide some more details.

HT5656 This is all great but for me the "IPv6 Delegated Prefix" field never sticks. After the reboot to apply the settings, it is empty again. I have tried the 6.2 Airport Utility on OS X 10.8.2 and the iOS Airport Utility. Any ideas?

Hi All,
   I had a working IPv6 tunnel with my Airport Express to tunnelbroker.net using the 7.6.1 firmware. After updating to 7.6.3, I have tried many things to get it to work and the only one that works is downgrading from 7.6.3 back to 7.6.1. After seeing this new technical note, it appears that the root of my issue is that I can not get the "IPv6 Delegated Prefix" field to stick - it is always empty after the reboot to apply the settings.
   Any ideas?
     Thanks,
       CraigN

I'm in the same boat with a 3rd Gen AEBS. Only thing I haven't tried is a complete reset and reconfiguration from nothing, which I may wind up doing this afternoon just to rule it out. The best irony of all of this is that tunnelbroker.net is under my responsibility, and I can't validate the new settings paradigm. At least getting back to 7.6.1 is easy enough and everything works fine there.
IPv6 Delegated prefix doesn't get saved when using the format from their example, then a 6to4 address shows up as the local address on the main Internet page, and no RAs are received once the AEBS comes back from a reload. Something's a little off on this release.

Why does a VRRP master with preemption disabled regain master state after the reboot ?

Q: Why does a VRRP master with preemption disabled regain master state after the reboot?
A: This issue is found in the following scenarios:
1. When spanning tree is disabled on either of the VRRP controllers but enabled on upstream switch(es).
2. When the controller(any one VRRP controller) and upstream device(s) run different versions of STP.
3. STP convergence time is different across the VRRP controllers.
In these scenarios, rebooted vrrp master is expected to come back as vrrp MASTER as the link takes some time to converge and fail to receive VRRP advertisement packets from its peer and may roll back to MASTER.
Trigger for this is, since STP is enabled on intermediate switch and disabled on controller, switch is taking some time ~30 secs to converge the link while port on the controller has become UP and fail-over to Master due to
not receiving VRRP advertisement packets
In all these cases, it is advised to enable holdtime to mitigate issue. Holdtime has been introduced to tackle this issue in the "preemption disabled scenario".
Configuration via CLI:
(controller) (config) #vrrp <id>
(controller) (config-vrrp)#holdtime
Description:
The VRRP virtual router does not begin listening to advertisements until the holdtime expires. If your deployment includes a VRRP master with preemption disabled and an uplink switch is running RSTP, a higher value will prevent the VRRP master from regaining the master state after it reboots.
Range: 30 - 120 seconds
Default: 45 seconds

Hey Jim,
Thanks for the follow-up. Here are some more details:
OS - 10.8.2
FCP X - 10.0.7
I can't update either of these because of my Avid installation.
Something else I didn't mention – this happens in a 4K project. Notice how a default Zoom title looks:
Lines 1 and 2 are almost stacked on top of each other.
Here's my title style:
Here's what the title looks after I apply the title style, modify Line 1, and remove the contents of Line 2:
And here's how it looks in the exported master file MOV:
Notice how it's pushed down?
Then I decided to make a 720p project. No more title problems.
So if you have some 4K footage, Jim, give it a go. Or if there's another 4K-er out there, try this and let me know.
Thanks!

HT3302 My iPod Touch fell into the washer and now does not start. What can I do to fix it?

My iPod Touch fell into the washer and now does not start. What can I do to fix it?

If it is totally dry:
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
Apple - iPod Repair price

Itunes will not start up after i downloaded it, itunes will not start up after i downloaded it

ok i have downloaded itunes 4 different times thinking it just didn't finish downloading . but still once more after i downloaded the software . it still will not start up when i click on the itunes . it gives me an error message about a apple support . and will not start up

it gives me an error message about a apple support
What's the precise text of that error message, please?

Have a Droid Razr M that is stuck in the reboot screen. I tried a hard reboot and a factory reset, and it still gets stuck in the reboot screen. How long should I wait for the reboot to occur until it starts back up?

Have a Droid Razr M that is stuck in the reboot screen. I tried a hard reboot and a factory reset, and it still gets stuck in the reboot screen. How long should I wait for the reboot to occur until it starts back up? I tried the steps for a factory reset given on this site, but it still does not want to work. Any help would be greatly appreciated.

Hello otter314!
Let's take a look into this to see if we can figure out what happened. When did this begin? What's the software version of the device? Do you remember what was happening with the device right before this started? Please supply me with some additional information, I'm happy to help with a resolution!
ChristinaB_VZW
VZW Support
Follow us on Twitter @VZWSupport

I have an Iphone 4 16gb and updated the IOS 6.1.2. after the update my 3G is not working at all??. can you please suggest what can be done to rectify this problem?

i have an Iphone 4 16gb and updated the IOS 6.1.2. after the update my 3G is not working at all??. can you please suggest what can be done to rectify this problem?

I have the same problem. After updating to 6.1.2 my iPad 3,2 will not find Verizon network. It just says "Searching..." for ever. Any thoughts?

My iphone will not sync to my computer saying the apple mobile device has not started

my iphone has not had problems with syncing to my computer. but when trying to sync today it wont. and my computer gives me a message that the phone cannot be used because the apple mobile device has not started. help?

Type "apple mobile device service" into the search bar at the top of this page by "Support" and read the resulting help articles.

HT1751 i bought a new, larger external hard drive. copied my itunes library from the old drive to the new one, changed the libarary location in Edit/Preferences/Advanced to the new drive. iTunes will not start or run unless old hard drive plugged in.??

I bought a new, larger external hard drive. I have my iTunes library on the external drive instead of C: drive, Using Windows 7.
I copied my itunes library from the old drive to the new one, changed the libarary location in Edit/Preferences/Advanced to the new drive.
iTunes will not start or run unless the old hard drive is plugged in.
If I disconnect the old drive iTunes shuts down.
Any ideas. ??

Hello kskip,
Thank you for providing so much information about what is going on. It sounds like you have setup iTunes to save new content to your new external hard drive in iTunes>Preferences, but it sounds like iTunes is not opening iTunes Library.itl file on the new external drive. You have one last step to take to have iTunes point to your new external hard drive rather than your old one:
Steps to create or choose a different iTunes Library file
If iTunes is running, quit iTunes.
If you are using Windows, hold down the Shift key and from the Start menu and choose All Programs > iTunes > iTunes.
You should see the following screen:
Additional information
If you do not see the screen above, then you did not hold the correct key at the correct time. You may want to try again. Note that if you pinned iTunes to the Start menu programs, and open it that way, it may not work.
Once you select "Choose Library," you will need to navigate to the iTunes Library.itl file on your new external drive.
You can find the full article here:
iTunes: How to open an alternate iTunes Library file or create a new one
http://support.apple.com/kb/ht1589
Thank you for using Apple Support Communities.
Best,
Sheila M.

When i plug my iphone 4 into itunes it says "this iphone cannot be used because the apple device serice is not started? what do i do

this iphone cannot be used because the apple device serice is not started? what do i do

http://support.apple.com/kb/ts1567

After the reboot, ssh demon is not starting up

Similar Messages

Maybe you are looking for